Make them more easy to read and edit by splitting to one element per
line when several elements are present.
Change-Id: I24ecfa1167b806dcb3a5a0c00343299df842a78b
When using 'check_PROGRAMS', autoconf/automake generates smarter
Makefiles, so that the test programs are not being compiled during
the normal 'make all', but only during 'make check'.
Change-Id: I18ebb7395024a490da743c0bcb20959e6e9c7017
Similar to what is already provided for power control loops. However,
there's no existing way to communicate TA control parameters from the
BSC to the BTS, so implement them locally in BTS vty.
Related: SYS#5371
Change-Id: I9fa71f836bb9a79b0ef2567bfcfdf38ff217840b
Field is renamed to look similar to similar fields in power control
loop. This is a preparation commit, next one will add functionality to
skip SACCH blocksi (P_CON_INTERVAL).
Related: SYS#5371
Change-Id: I169ce58ab827e38b64f4b15f935097a9118fa118
From TS 45.010 5.6.1 (delay tracking for circuit switched channels):
"""
Restricting the change in timing advance to 1 symbol period at a time
gives the simplest implementation of the BTS. However the BTS may use
a larger change than this but great care must then be used in the BTS design.
"""
In general 1 TA at a time (every 480ms of SACCH block) should be enough,
since section 5.6.3 states:
"""
The control loop for the timing advance shall be implemented in such a way that it will cope with MSs moving at a
speed up to 500 km/h
"""
Which is ~140 m/s, and 1 TA step around 500m, so most of the time we
should be save and no steps of more than 1 TA should be required.
However, unlikely changes from reflected to direct signal or vice versa
could produce higher increments, so let's increase the maximum step size
allowed to 2 in order to give more room.
Change-Id: I9e48faabf3090588233e274b2b39065cf85fbec7
First step improving and reworking TA loop:
Move trigger of the loop to similar place done by BS/MS Power Control
Loop, that is, upon receivial of UL SACCH block, which contains
information about the TA used to transmit the block encode in L1SACCH
Header. Hence, from computed received TOA and TA used when transmitting
from the MS, we can infer the desired TA to be used by the MS, which
will send back to it later during DL SACCH block.
The values taken are actually the ones calculated for the previous SACCH
block and stored in lchan->meas.ms_toa256. That's because L1SACCH
contains the TA used for the previous reporting period, similarly to
what's specified for MS Power Control loop (TS 45.008 sec 4.2):
"""
The MS shall confirm the power control level that it is currently employing
in the SACCH L1 header on each uplink channel. The indicated value shall
be the power control level actually used by the mobile for the last burst
of the previous SACCH period.
"""
(The reader may observe that currently this is not properly done for MS
Power Control loop when calling lchan_ms_pwr_ctrl(): this is a bug.)
This new method also permits changing TA quicker, since we have more
confidence that the TA we request is aligned with the one used to
transmit, and we don't simply increment/decrement based on the value we
request to transmit.
Related: SYS#5371
Change-Id: I2d0f128c8dcac93ee382283a1c91fca76623b8fc
The timing advance controller that is implemented in loops.c of
osmo-bts-trx only works for osmo-bts-trx and not for any of the phy
based bts. Lets move the timing advance controller into the common part
and make it available for every bts. Also lets add a unit-test.
Change-Id: If7ddf74db3abc9b9872abe620a0aeebe3327e70a
Related: SYS#4567
Pau Espin
Vadim Yanitskiy
Philipp Maier