Since 95407f3f osmo-bts-trx supports scheduling all CSD specific
channel rates, however the rate adaptation was missing.
On the radio interface we deal with CSD-modified V.110 frames, which
need to be converted to normal 80-bit V.110 frames (RA1'/RA1), which
in turn need to be batched and sent in RFC4040 "clearmode" 160 octet
RTP payloads (RA1/RA2 as per I.460).
Note that this patch comments out TCH/F14.4 in bts_supports_cm_data(),
so that all channel allocations for this mode would be NACKed. The
reason for this is that the rate adaptation functions for TCH/F14.4
are different than the RA1'/RA1 and the RA1/RA2.
For more information, see:
* 3GPP TS 44.021, section 8 (functions RA1'/RA1)
* ITU-T I.460, section 1.1 "Rate adaption of 8, 16 and 32 kbit/s streams"
Change-Id: I5e3701ad52d5d428fd02caff037881045f2d0a02
Related: OS#1572
Random access is allowed on VGCS / VBS channels to access the uplink or
to detect listeners. Uplink Access from a listener is only reported once
after activating the channel. Uplink Access from a talker is reported
each time the uplink becomes occupied. RSL TALKER/LISTENER DETECT
messages are sent to the bsc.
The VGCS UPLINK GRANT message is sent by the BTS itself. Timer T3115 is
used to repeat the message up to NY2 times until one valid frame is
received from the MS (CM service request). The UPLINK BUSY / UPLINK FREE
message must be sent by the BSC.
The uplink is released by UPLINK RELEASE message from the MS or from the
BSC. Afterwards the UPLINK FREE message causes the MS to leave the
uplink without any acknowlege. An RSL REL-REQ must be used to terminate
the link locally. (Without layer 2 DISC procedure.)
Change-Id: I1bd07ab6802341b09a06e89df356665ffaf6d2bf
Related: OS#4851
This adds very minimalistic support for notification of VBS/VGCS calls.
Minimalistic in that we
* only notify via PCH (not via NCH or FACCH)
* only include notification in otherwise empty PAGING TYPE 1
This means that notification will cease to work once the PCH becomes too
loaded and we never would send otherwise empty PAGING TYPE 1 anymore.
Change-Id: I6f6f72d9a0123cb519b341d72a124aaa2117370e
Requires: libosmocore.git I9586b5cb8514010d9358fcfc97c3d34741294522
Related: OS#5781
Up until now, our approach to validating incoming RTP payloads and
dropping invalid ones has been to apply the preening function inside
l1sap_tch_rts_ind(), at the point of dequeueing from the DL input queue.
However, there are some RTP formats where we need to strip one byte
of header from the payload before passing the rest to our innards:
there is RFC 5993 for HR codec, and there also exists a non-standard
extension (rtp_traulike) that does a similar deal for FR and EFR.
Because of alignment issues, it will be more efficient (avoids memmove)
if we can do this header octet stripping before we copy the payload
into msgb - but doing so requires that we move this preening logic
to the point of RTP input before enqueueing. Make this change.
Related: OS#5688
Change-Id: I7fc99aeecba8303b56d397b8952de5eea82b301e
This way the data model in TS 12.21 (Figure 1) is followed, where
there's a BTS Site Manager containing one or more BTS. In our case we
only support 1 BTS (cell) so far.
Change-Id: Ideb0d458ec631008223f861cf8b46d09524a1a21
Related: OS#5994
Let's split all lchan and power_control specific stuff into their own headers,
it helps finding out data and operations available related to them.
We already have similar classification in osmo-bsc.
Change-Id: I6424dcbd2e329fc1a516f8886359554ed7e9487e
This new extension protocol is used to forward Osmocom PCUIF messages
BSC<->BTS<->PCU.
It will be sent re-using the IPA multiplex of the OML link between
BSC and BTS. BTS is responsible for forwarding the message over the unix
socket to the PCU.
PCUIF existing RX path needs to be reworked in order to accept
variable-size messages, in order to be able to transparently forward
messages without knowing about them (the new container message is
variable-length).
Related: SYS#5303
Change-Id: I73fdb17107494ade9263a62d1f729e67303fce87
This fixes old behavior mimicing broken behavior in nanoBTS (according to TS 12.21)
where BTS Site Mgr NM object was announced as Enabled despite no OPSTART
was sent by the BSC.
With this new FSM, BTS SiteManager will be announced as Disabled Offline
during OML startup conversation, instead of Enabled.
The new osmo-bsc OML management FSMs use this change in behavior to find
out whether it should use the old broken management states (without
Offline state, as per nanoBTS) or use the new state transitions (which
allow fixing several race conditions).
Change-Id: Iab2d17c45c9642860cd2d5d523c1baae24502243
Move all struct gsm_bts_trx references from bulky gsm_data to its own
file containing all related definitions and implementations. Also move a
few functions clearly related to that object which were placed in bts.*
Change-Id: Iebaf5b221c48b571f45408af867ce6f9c0cd9f4a
Using an FSM here will allow for more complex ordered shutdown
procedures, like power ramp down, waiting for TRX deact asyncrhonously,
etc.
Current commit leaves everything in place already prepared to implement
ramp down, which will be implemented in next commit in the series.
Related: SYS#4920
Change-Id: I8f48f17e61c3b9b86342eaf5b8a2b1ac9758bde5
Old _shared one comes from time where we shared header with other
componenets. It's no longer the case sine a logn time ago.
The gsm_data_shared.h is only being included by gsm_data.h nowadays, so
let's simply merge it to simplify header dependency and struct
definitions.
Similarly, gsm_data_shared.c is renamed to gsm_data.c
Change-Id: Id60e7582e3a32dbc5e3531b87b2b49f07aee734d
The timing advance controller that is implemented in loops.c of
osmo-bts-trx only works for osmo-bts-trx and not for any of the phy
based bts. Lets move the timing advance controller into the common part
and make it available for every bts. Also lets add a unit-test.
Change-Id: If7ddf74db3abc9b9872abe620a0aeebe3327e70a
Related: SYS#4567
* copy-paste gsm_data_shared.* from OpenBSC master
* remove corresponding configure check and option
* remove .deb dependency
Actual refactoring with removal of unnecessary structures/parts, moving
common OpenBSC/OsmoBSC parts into libraries etc. are left for further
patches.
Current patch will make coexistence with *BSC easier and will simplify
our build infrastructure.
Change-Id: I9f004fb5c4c1db29d4792dfd281d388c7063da13
Related: OS#1923
Use dedicated FSM to handle all DTX DL related events:
- add explicit checks if DTX DL is enabled (fixes regression for non-DTX
setup introduced in 654175f33b)
- fix handling of AMR CMI for SPEECH frames
- add FSM for DTX DL
- sync with corresponding changes in OpenBSC's
- handle FACCH-related DTX ONSET events
This affects both lc15 and sysmobts and requires corresponding change in
OpenBSC (Change-Id: Idac8609faf9b5ced818fde899ccfc6ed0c42e8fd).
Change-Id: I74a0b42cb34d525b8a70d264135e82994ca70d31
MS uplink power control is required in pretty much any BTS, and we
cannot assume that they PHY / L1 will always take care of it by
itself. So the correspondign code is moved to common/power_control.c
and called from the generic part of L1SAP.
The corresponding VTY paramter has been moved from the sysmobts-specific
trx VTY node to the common BTS VTY node.
Instead of handling primitives directly at layer 1 specific code,
osmo-bts handles primitives at common code.
When all primitive are moved, the l1sap interface will:
- receive PH-DATA indications and forward them to layer 2.
- check for RF link loss and notify BSC.
- receive TCH indications and forward them via RTP.
- receive PH-RTS indications and send PH-DATA requests with content
according to its logical channel.
- receive TCH-RTS indications and send TCH requests with content
received via RTP or loopback from TCH indications.
- send MPH-INFO requests to activate, deactivate and modify logical
channels and handle their confirms.
- receive MPH-INFO indications with measurements from tranceiver.
- forward received and transmitted PH-DATA to GSMTAP.
In order to support transmit power reduction by thermal management
as well as the variety of new internal / external PA configurations
of BTSs, we need a slightly more complex system.
Also, as at high power a single dB can be quite a big difference,
we are now doing all computations in milli-dB(m), i.e. 1/10000 bel.
Ramping is now used both for up and down ramping, as that is useful in
cases where you want to gracefully shut down a cell by shrinking its
radius, gradually handing over subscribers to neighboring cells.
Furthermore, this code is becoming part of the 'common' codebase, as it
is not really specific to how sysmobts is working.
The user can specify a single aggregate value for external system
gain/attenuation. Let's say you have 1dB loss of antenna cable, so you
can put that as 'user-gain -1' into the config, which means that a
'transmit power of 20dBm' will be compensatet for that and the TRX is
instructed to output 21dBm to compensate the cable loss. Similarly,
external PAs can be described by a positive user-gain.
One of the next steps will be to communicate those values and the
nominal power capability of the specific BTS to the BSC, so the BSC will
automatically show correct signal levels in the VTY and log files.
The code includes provisions for future extensions regarding
* an external and an internal PA with calibration tables
* a thermal attenuation setting to be controlled by the site manager
Extend the router to verify that the message received is
properly encoded. The code can deal with the basic structure
of ETSI OML and vendor specific messages for ip.access and
the osmocom project.
* Comment out the osmo-bts-bb/Makefile as we have removed it from
the SUBDIRS and are not packaging the code right now
* Add missing include files for the build
This only implements creating, binding, connecting and free'ing RTP
sockets, not yet anything regarding receiving or transmitting codec
frames on them.
You will need the rtp branch of libosmocore for libosmotrau
* gather measurements from each PH-DATA.ind
* check every TDMA frame about meas period expiration
* compute averages after period expired
* put MS DL MEAS REP into RSL MEAS RES messages, include UL meas
bugs:
* L3 INFO content seems to have some offset
* is_sub is not set anywhere
* measurement periods might have up/downlink offset
This code re-works osmo-bts to add support for the upcoming sysmocom BTS.
It also tries to add some level of abstraction between the generic
part of a BTS (A-bis, RSL, OML, data structures, paging scheduling,
BCCH/AGCH scheduling, etc.) and the actual hardware-specific bits.
The hardware-specific bits are currently only implemented for the sysmocom
femtobts, but should be (re-)added for osmocom-bb, as well as a virtual
BTS for simulation purpose later.
The sysmocom bts specific parts require hardware-specific header files
which are (at least currently) not publicly distributed.
Vadim Yanitskiy
Harald Welte
Mychaela N. Falconia
Pau Espin
Philipp Maier