2019-06-19 10:18:24 +00:00
<vtydoc xmlns= 'urn:osmocom:xml:libosmocore:vty:doc:1.0' >
<node id= '_common_cmds_' >
<name > Common Commands</name>
<description > These commands are available on all VTY nodes. They are listed here only once, to unclutter the VTY reference.</description>
<command id= 'help' >
<params >
<param name= 'help' doc= 'Description of the interactive help system' />
</params>
</command>
<command id= 'list' >
<params >
<param name= 'list' doc= 'Print command list' />
</params>
</command>
<command id= 'write terminal' >
<params >
<param name= 'write' doc= 'Write running configuration to memory, network, or terminal' />
<param name= 'terminal' doc= 'Write to terminal' />
</params>
</command>
2020-05-29 11:49:03 +00:00
<command id= 'write file [PATH]' >
2019-06-19 10:18:24 +00:00
<params >
<param name= 'write' doc= 'Write running configuration to memory, network, or terminal' />
<param name= 'file' doc= 'Write to configuration file' />
2020-05-29 11:49:03 +00:00
<param name= '[PATH]' doc= 'Set file path to store the config, or replace if already exists' />
2019-06-19 10:18:24 +00:00
</params>
</command>
<command id= 'write memory' >
<params >
<param name= 'write' doc= 'Write running configuration to memory, network, or terminal' />
<param name= 'memory' doc= 'Write configuration to the file (same as write file)' />
</params>
</command>
<command id= 'write' >
<params >
<param name= 'write' doc= 'Write running configuration to memory, network, or terminal' />
</params>
</command>
<command id= 'show running-config' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'running-config' doc= 'running configuration' />
</params>
</command>
<command id= 'exit' >
<params >
<param name= 'exit' doc= 'Exit current mode and down to previous mode' />
</params>
</command>
<command id= 'end' >
<params >
<param name= 'end' doc= 'End current mode and change to enable mode.' />
</params>
</command>
</node>
<node id= 'view' >
<name > view</name>
<command id= 'show version' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'version' doc= 'Displays program version' />
</params>
</command>
<command id= 'show online-help' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'online-help' doc= 'Online help' />
</params>
</command>
<command id= 'enable' >
<params >
<param name= 'enable' doc= 'Turn on privileged mode command' />
</params>
</command>
<command id= 'terminal length <0-512>' >
<params >
<param name= 'terminal' doc= 'Set terminal line parameters' />
<param name= 'length' doc= 'Set number of lines on a screen' />
<param name= '<0-512>' doc= 'Number of lines on screen (0 for no pausing)' />
</params>
</command>
<command id= 'terminal no length' >
<params >
<param name= 'terminal' doc= 'Set terminal line parameters' />
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'length' doc= 'Set number of lines on a screen' />
</params>
</command>
<command id= 'who' >
<params >
<param name= 'who' doc= 'Display who is on vty' />
</params>
</command>
<command id= 'show history' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'history' doc= 'Display the session command history' />
</params>
</command>
<command id= 'show e1_driver' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'e1_driver' doc= 'Display information about available E1 drivers' />
</params>
</command>
<command id= 'show e1_line [line_nr] [stats]' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'e1_line' doc= 'Display information about a E1 line' />
<param name= '[line_nr]' doc= 'E1 Line Number' />
<param name= '[stats]' doc= 'Include statistics' />
</params>
</command>
<command id= 'show e1_timeslot [line_nr] [ts_nr]' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'e1_timeslot' doc= 'Display information about a E1 timeslot' />
<param name= '[line_nr]' doc= 'E1 Line Number' />
<param name= '[ts_nr]' doc= 'E1 Timeslot Number' />
</params>
</command>
<command id= 'show bts <0-255>' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'bts' doc= 'Display information about a BTS' />
<param name= '<0-255>' doc= 'BTS Number' />
</params>
</command>
<command id= 'show trx [<0-255>] [<0-255>]' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'trx' doc= 'Display information about a TRX' />
<param name= '[<0-255>]' doc= 'BTS Number' />
<param name= '[<0-255>]' doc= 'TRX Number' />
</params>
</command>
<command id= 'show timeslot [<0-255>] [<0-255>] [<0-7>]' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'timeslot' doc= 'Display information about a TS' />
<param name= '[<0-255>]' doc= 'BTS Number' />
<param name= '[<0-255>]' doc= 'TRX Number' />
<param name= '[<0-7>]' doc= 'Timeslot Number' />
</params>
</command>
<command id= 'show lchan [<0-255>] [<0-255>] [<0-7>] [<0-7>]' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'lchan' doc= 'Display information about a logical channel' />
<param name= '[<0-255>]' doc= 'BTS Number' />
<param name= '[<0-255>]' doc= 'TRX Number' />
<param name= '[<0-7>]' doc= 'Timeslot Number' />
<param name= '[<0-7>]' doc= 'Logical Channel Number' />
</params>
</command>
<command id= 'show lchan summary [<0-255>] [<0-255>] [<0-7>] [<0-7>]' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'lchan' doc= 'Display information about a logical channel' />
<param name= 'summary' doc= 'Short summary' />
<param name= '[<0-255>]' doc= 'BTS Number' />
<param name= '[<0-255>]' doc= 'TRX Number' />
<param name= '[<0-7>]' doc= 'Timeslot Number' />
<param name= '[<0-7>]' doc= 'Logical Channel Number' />
</params>
</command>
2020-05-29 11:49:03 +00:00
<command id= 'logging filter l1-sapi (unknown|agch|bcch|cbch|facch/f|facch/h|fcch|idle|nch|pacch|pagch|pbcch|pch|pdtch|pnch|ppch|prach|ptcch|rach|sacch|sch|sdcch|tch/f|tch/h)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'filter' doc= 'Filter log messages' />
<param name= 'l1-sapi' doc= 'L1 SAPI' />
<param name= 'unknown' doc= 'UNKNOWN' />
<param name= 'agch' doc= 'AGCH' />
<param name= 'bcch' doc= 'BCCH' />
<param name= 'cbch' doc= 'CBCH' />
<param name= 'facch/f' doc= 'FACCH/F' />
<param name= 'facch/h' doc= 'FACCH/H' />
<param name= 'fcch' doc= 'FCCH' />
<param name= 'idle' doc= 'IDLE' />
<param name= 'nch' doc= 'NCH' />
<param name= 'pacch' doc= 'PACCH' />
<param name= 'pagch' doc= 'PAGCH' />
<param name= 'pbcch' doc= 'PBCCH' />
<param name= 'pch' doc= 'PCH' />
<param name= 'pdtch' doc= 'PDTCH' />
<param name= 'pnch' doc= 'PNCH' />
<param name= 'ppch' doc= 'PPCH' />
<param name= 'prach' doc= 'PRACH' />
<param name= 'ptcch' doc= 'PTCCH' />
<param name= 'rach' doc= 'RACH' />
<param name= 'sacch' doc= 'SACCH' />
<param name= 'sch' doc= 'SCH' />
<param name= 'sdcch' doc= 'SDCCH' />
<param name= 'tch/f' doc= 'TCH/F' />
<param name= 'tch/h' doc= 'TCH/H' />
</params>
</command>
<command id= 'no logging filter l1-sapi (unknown|agch|bcch|cbch|facch/f|facch/h|fcch|idle|nch|pacch|pagch|pbcch|pch|pdtch|pnch|ppch|prach|ptcch|rach|sacch|sch|sdcch|tch/f|tch/h)' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'logging' doc= 'Configure logging' />
<param name= 'filter' doc= 'Filter log messages' />
<param name= 'l1-sapi' doc= 'L1 SAPI' />
<param name= 'unknown' doc= 'UNKNOWN' />
<param name= 'agch' doc= 'AGCH' />
<param name= 'bcch' doc= 'BCCH' />
<param name= 'cbch' doc= 'CBCH' />
<param name= 'facch/f' doc= 'FACCH/F' />
<param name= 'facch/h' doc= 'FACCH/H' />
<param name= 'fcch' doc= 'FCCH' />
<param name= 'idle' doc= 'IDLE' />
<param name= 'nch' doc= 'NCH' />
<param name= 'pacch' doc= 'PACCH' />
<param name= 'pagch' doc= 'PAGCH' />
<param name= 'pbcch' doc= 'PBCCH' />
<param name= 'pch' doc= 'PCH' />
<param name= 'pdtch' doc= 'PDTCH' />
<param name= 'pnch' doc= 'PNCH' />
<param name= 'ppch' doc= 'PPCH' />
<param name= 'prach' doc= 'PRACH' />
<param name= 'ptcch' doc= 'PTCCH' />
<param name= 'rach' doc= 'RACH' />
<param name= 'sacch' doc= 'SACCH' />
<param name= 'sch' doc= 'SCH' />
<param name= 'sdcch' doc= 'SDCCH' />
<param name= 'tch/f' doc= 'TCH/F' />
<param name= 'tch/h' doc= 'TCH/H' />
</params>
</command>
2019-06-19 10:18:24 +00:00
<command id= 'logging enable' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'enable' doc= 'Enables logging to this vty' />
</params>
</command>
<command id= 'logging disable' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'disable' doc= 'Disables logging to this vty' />
</params>
</command>
<command id= 'logging filter all (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'filter' doc= 'Filter log messages' />
<param name= 'all' doc= 'Do you want to log all messages?' />
<param name= '0' doc= 'Only print messages matched by other filters' />
<param name= '1' doc= 'Bypass filter and print all messages' />
</params>
</command>
<command id= 'logging color (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'color' doc= 'Configure color-printing for log messages' />
<param name= '0' doc= 'Don't use color for printing messages' />
<param name= '1' doc= 'Use color for printing messages' />
</params>
</command>
<command id= 'logging timestamp (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'timestamp' doc= 'Configure log message timestamping' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with current timestamp' />
</params>
</command>
<command id= 'logging print extended-timestamp (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'extended-timestamp' doc= 'Configure log message timestamping' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
</params>
</command>
<command id= 'logging print category (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'category' doc= 'Configure log message' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with category/subsystem name' />
</params>
</command>
<command id= 'logging print category-hex (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'category-hex' doc= 'Configure log message' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with category/subsystem nr in hex ('<000b>')' />
</params>
</command>
<command id= 'logging print level (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'level' doc= 'Configure log message' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with the log level name' />
</params>
</command>
<command id= 'logging print file (0|1|basename) [last]' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'file' doc= 'Configure log message' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with the source file and line' />
<param name= 'basename' doc= 'Prefix each log message with the source file's basename (strip leading paths) and line' />
<param name= '[last]' doc= 'Log source file info at the end of a log line. If omitted, log source file info just before the log text.' />
</params>
</command>
<command id= 'logging set-log-mask MASK' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'set-log-mask' doc= 'Set the logmask of this logging target' />
<param name= 'MASK' doc= 'List of logging categories to log, e.g. 'abc:mno:xyz'. Available log categories depend on the specific application, refer to the 'logging level' command. Optionally add individual log levels like 'abc,1:mno,3:xyz,5', where the level numbers are LOGL_DEBUG=1 LOGL_INFO=3 LOGL_NOTICE=5 LOGL_ERROR=7 LOGL_FATAL=8' />
</params>
</command>
<command id= 'logging level (rsl|oml|rll|rr|meas|pag|l1c|l1p|dsp|pcu|ho|trx|loop|abis|rtp|sum|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'level' doc= 'Set the log level for a specified category' />
<param name= 'rsl' doc= 'A-bis Radio Siganlling Link (RSL)' />
<param name= 'oml' doc= 'A-bis Network Management / O&M (NM/OML)' />
<param name= 'rll' doc= 'A-bis Radio Link Layer (RLL)' />
<param name= 'rr' doc= 'Layer3 Radio Resource (RR)' />
<param name= 'meas' doc= 'Radio Measurement Processing' />
<param name= 'pag' doc= 'Paging Subsystem' />
<param name= 'l1c' doc= 'Layer 1 Control (MPH)' />
<param name= 'l1p' doc= 'Layer 1 Primitives (PH)' />
<param name= 'dsp' doc= 'DSP Trace Messages' />
<param name= 'pcu' doc= 'PCU interface' />
<param name= 'ho' doc= 'Handover' />
<param name= 'trx' doc= 'TRX interface' />
<param name= 'loop' doc= 'Control loops' />
<param name= 'abis' doc= 'A-bis Intput Subsystem' />
<param name= 'rtp' doc= 'Realtime Transfer Protocol' />
<param name= 'sum' doc= 'DSUM' />
<param name= 'lglobal' doc= 'Library-internal global log family' />
<param name= 'llapd' doc= 'LAPD in libosmogsm' />
<param name= 'linp' doc= 'A-bis Intput Subsystem' />
<param name= 'lmux' doc= 'A-bis B-Subchannel TRAU Frame Multiplex' />
<param name= 'lmi' doc= 'A-bis Input Driver for Signalling' />
<param name= 'lmib' doc= 'A-bis Input Driver for B-Channels (voice)' />
<param name= 'lsms' doc= 'Layer3 Short Message Service (SMS)' />
<param name= 'lctrl' doc= 'Control Interface' />
<param name= 'lgtp' doc= 'GPRS GTP library' />
<param name= 'lstats' doc= 'Statistics messages and logging' />
<param name= 'lgsup' doc= 'Generic Subscriber Update Protocol' />
<param name= 'loap' doc= 'Osmocom Authentication Protocol' />
<param name= 'lss7' doc= 'libosmo-sigtran Signalling System 7' />
<param name= 'lsccp' doc= 'libosmo-sigtran SCCP Implementation' />
<param name= 'lsua' doc= 'libosmo-sigtran SCCP User Adaptation' />
<param name= 'lm3ua' doc= 'libosmo-sigtran MTP3 User Adaptation' />
<param name= 'lmgcp' doc= 'libosmo-mgcp Media Gateway Control Protocol' />
<param name= 'ljibuf' doc= 'libosmo-netif Jitter Buffer' />
<param name= 'lrspro' doc= 'Remote SIM protocol' />
<param name= 'debug' doc= 'Log debug messages and higher levels' />
<param name= 'info' doc= 'Log informational messages and higher levels' />
<param name= 'notice' doc= 'Log noticeable messages and higher levels' />
<param name= 'error' doc= 'Log error messages and higher levels' />
<param name= 'fatal' doc= 'Log only fatal messages' />
</params>
</command>
<command id= 'logging level set-all (debug|info|notice|error|fatal)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'level' doc= 'Set the log level for a specified category' />
<param name= 'set-all' doc= 'Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' />
<param name= 'debug' doc= 'Log debug messages and higher levels' />
<param name= 'info' doc= 'Log informational messages and higher levels' />
<param name= 'notice' doc= 'Log noticeable messages and higher levels' />
<param name= 'error' doc= 'Log error messages and higher levels' />
<param name= 'fatal' doc= 'Log only fatal messages' />
</params>
</command>
<command id= 'logging level force-all (debug|info|notice|error|fatal)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'level' doc= 'Set the log level for a specified category' />
<param name= 'force-all' doc= 'Globally force all logging categories to a specific level. This is released by the 'no logging level force-all' command. Note: any 'logging level <category> <level>' commands will have no visible effect after this, until the forced level is released.' />
<param name= 'debug' doc= 'Log debug messages and higher levels' />
<param name= 'info' doc= 'Log informational messages and higher levels' />
<param name= 'notice' doc= 'Log noticeable messages and higher levels' />
<param name= 'error' doc= 'Log error messages and higher levels' />
<param name= 'fatal' doc= 'Log only fatal messages' />
</params>
</command>
<command id= 'no logging level force-all' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'logging' doc= 'Configure logging' />
<param name= 'level' doc= 'Set the log level for a specified category' />
<param name= 'force-all' doc= 'Release any globally forced log level set with 'logging level force-all <level>'' />
</params>
</command>
2020-05-29 11:49:03 +00:00
<command id= 'logp (rsl|oml|rll|rr|meas|pag|l1c|l1p|dsp|pcu|ho|trx|loop|abis|rtp|sum|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal) .LOGMESSAGE' >
<params >
<param name= 'logp' doc= 'Print a message on all log outputs; useful for placing markers in test logs' />
<param name= 'rsl' doc= 'A-bis Radio Siganlling Link (RSL)' />
<param name= 'oml' doc= 'A-bis Network Management / O&M (NM/OML)' />
<param name= 'rll' doc= 'A-bis Radio Link Layer (RLL)' />
<param name= 'rr' doc= 'Layer3 Radio Resource (RR)' />
<param name= 'meas' doc= 'Radio Measurement Processing' />
<param name= 'pag' doc= 'Paging Subsystem' />
<param name= 'l1c' doc= 'Layer 1 Control (MPH)' />
<param name= 'l1p' doc= 'Layer 1 Primitives (PH)' />
<param name= 'dsp' doc= 'DSP Trace Messages' />
<param name= 'pcu' doc= 'PCU interface' />
<param name= 'ho' doc= 'Handover' />
<param name= 'trx' doc= 'TRX interface' />
<param name= 'loop' doc= 'Control loops' />
<param name= 'abis' doc= 'A-bis Intput Subsystem' />
<param name= 'rtp' doc= 'Realtime Transfer Protocol' />
<param name= 'sum' doc= 'DSUM' />
<param name= 'lglobal' doc= 'Library-internal global log family' />
<param name= 'llapd' doc= 'LAPD in libosmogsm' />
<param name= 'linp' doc= 'A-bis Intput Subsystem' />
<param name= 'lmux' doc= 'A-bis B-Subchannel TRAU Frame Multiplex' />
<param name= 'lmi' doc= 'A-bis Input Driver for Signalling' />
<param name= 'lmib' doc= 'A-bis Input Driver for B-Channels (voice)' />
<param name= 'lsms' doc= 'Layer3 Short Message Service (SMS)' />
<param name= 'lctrl' doc= 'Control Interface' />
<param name= 'lgtp' doc= 'GPRS GTP library' />
<param name= 'lstats' doc= 'Statistics messages and logging' />
<param name= 'lgsup' doc= 'Generic Subscriber Update Protocol' />
<param name= 'loap' doc= 'Osmocom Authentication Protocol' />
<param name= 'lss7' doc= 'libosmo-sigtran Signalling System 7' />
<param name= 'lsccp' doc= 'libosmo-sigtran SCCP Implementation' />
<param name= 'lsua' doc= 'libosmo-sigtran SCCP User Adaptation' />
<param name= 'lm3ua' doc= 'libosmo-sigtran MTP3 User Adaptation' />
<param name= 'lmgcp' doc= 'libosmo-mgcp Media Gateway Control Protocol' />
<param name= 'ljibuf' doc= 'libosmo-netif Jitter Buffer' />
<param name= 'lrspro' doc= 'Remote SIM protocol' />
<param name= 'debug' doc= 'Log debug messages and higher levels' />
<param name= 'info' doc= 'Log informational messages and higher levels' />
<param name= 'notice' doc= 'Log noticeable messages and higher levels' />
<param name= 'error' doc= 'Log error messages and higher levels' />
<param name= 'fatal' doc= 'Log only fatal messages' />
<param name= '.LOGMESSAGE' doc= 'Arbitrary message to log on given category and log level' />
</params>
</command>
2019-06-19 10:18:24 +00:00
<command id= 'show logging vty' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'logging' doc= 'Show current logging configuration' />
<param name= 'vty' doc= 'Show current logging configuration for this vty' />
</params>
</command>
<command id= 'show alarms' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'alarms' doc= 'Show current logging configuration' />
</params>
</command>
<command id= 'show talloc-context (application|all) (full|brief|DEPTH)' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'talloc-context' doc= 'Show talloc memory hierarchy' />
<param name= 'application' doc= 'Application's context' />
<param name= 'all' doc= 'All contexts, if NULL-context tracking is enabled' />
<param name= 'full' doc= 'Display a full talloc memory hierarchy' />
<param name= 'brief' doc= 'Display a brief talloc memory hierarchy' />
<param name= 'DEPTH' doc= 'Specify required maximal depth value' />
</params>
</command>
<command id= 'show talloc-context (application|all) (full|brief|DEPTH) tree ADDRESS' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'talloc-context' doc= 'Show talloc memory hierarchy' />
<param name= 'application' doc= 'Application's context' />
<param name= 'all' doc= 'All contexts, if NULL-context tracking is enabled' />
<param name= 'full' doc= 'Display a full talloc memory hierarchy' />
<param name= 'brief' doc= 'Display a brief talloc memory hierarchy' />
<param name= 'DEPTH' doc= 'Specify required maximal depth value' />
<param name= 'tree' doc= 'Display only a specific memory chunk' />
<param name= 'ADDRESS' doc= 'Chunk address (e.g. 0xdeadbeef)' />
</params>
</command>
<command id= 'show talloc-context (application|all) (full|brief|DEPTH) filter REGEXP' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'talloc-context' doc= 'Show talloc memory hierarchy' />
<param name= 'application' doc= 'Application's context' />
<param name= 'all' doc= 'All contexts, if NULL-context tracking is enabled' />
<param name= 'full' doc= 'Display a full talloc memory hierarchy' />
<param name= 'brief' doc= 'Display a brief talloc memory hierarchy' />
<param name= 'DEPTH' doc= 'Specify required maximal depth value' />
<param name= 'filter' doc= 'Filter chunks using regular expression' />
<param name= 'REGEXP' doc= 'Regular expression' />
</params>
</command>
<command id= 'show stats' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'stats' doc= 'Show statistical values' />
</params>
</command>
<command id= 'show stats level (global|peer|subscriber)' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'stats' doc= 'Show statistical values' />
<param name= 'level' doc= 'Set the maximum group level' />
<param name= 'global' doc= 'Show global groups only' />
<param name= 'peer' doc= 'Show global and network peer related groups' />
<param name= 'subscriber' doc= 'Show global, peer, and subscriber groups' />
</params>
</command>
<command id= 'show asciidoc counters' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'asciidoc' doc= 'Asciidoc generation' />
<param name= 'counters' doc= 'Generate table of all registered counters' />
</params>
</command>
<command id= 'show rate-counters' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'rate-counters' doc= 'Show all rate counters' />
</params>
</command>
</node>
<node id= 'enable' >
<name > enable</name>
<command id= 'disable' >
<params >
<param name= 'disable' doc= 'Turn off privileged mode command' />
</params>
</command>
<command id= 'configure terminal' >
<params >
<param name= 'configure' doc= 'Configuration from vty interface' />
<param name= 'terminal' doc= 'Configuration terminal' />
</params>
</command>
<command id= 'copy running-config startup-config' >
<params >
<param name= 'copy' doc= 'Copy configuration' />
<param name= 'running-config' doc= 'Copy running config to... ' />
<param name= 'startup-config' doc= 'Copy running config to startup config (same as write file)' />
</params>
</command>
<command id= 'show startup-config' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'startup-config' doc= 'Contentes of startup configuration' />
</params>
</command>
<command id= 'show version' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'version' doc= 'Displays program version' />
</params>
</command>
<command id= 'show online-help' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'online-help' doc= 'Online help' />
</params>
</command>
<command id= 'terminal length <0-512>' >
<params >
<param name= 'terminal' doc= 'Set terminal line parameters' />
<param name= 'length' doc= 'Set number of lines on a screen' />
<param name= '<0-512>' doc= 'Number of lines on screen (0 for no pausing)' />
</params>
</command>
<command id= 'terminal no length' >
<params >
<param name= 'terminal' doc= 'Set terminal line parameters' />
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'length' doc= 'Set number of lines on a screen' />
</params>
</command>
<command id= 'who' >
<params >
<param name= 'who' doc= 'Display who is on vty' />
</params>
</command>
<command id= 'show history' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'history' doc= 'Display the session command history' />
</params>
</command>
<command id= 'terminal monitor' >
<params >
<param name= 'terminal' doc= 'Set terminal line parameters' />
<param name= 'monitor' doc= 'Copy debug output to the current terminal line' />
</params>
</command>
<command id= 'terminal no monitor' >
<params >
<param name= 'terminal' doc= 'Set terminal line parameters' />
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'monitor' doc= 'Copy debug output to the current terminal line' />
</params>
</command>
<command id= 'show e1_driver' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'e1_driver' doc= 'Display information about available E1 drivers' />
</params>
</command>
<command id= 'show e1_line [line_nr] [stats]' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'e1_line' doc= 'Display information about a E1 line' />
<param name= '[line_nr]' doc= 'E1 Line Number' />
<param name= '[stats]' doc= 'Include statistics' />
</params>
</command>
<command id= 'show e1_timeslot [line_nr] [ts_nr]' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'e1_timeslot' doc= 'Display information about a E1 timeslot' />
<param name= '[line_nr]' doc= 'E1 Line Number' />
<param name= '[ts_nr]' doc= 'E1 Timeslot Number' />
</params>
</command>
<command id= 'show bts <0-255>' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'bts' doc= 'Display information about a BTS' />
<param name= '<0-255>' doc= 'BTS Number' />
</params>
</command>
<command id= 'show trx [<0-255>] [<0-255>]' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'trx' doc= 'Display information about a TRX' />
<param name= '[<0-255>]' doc= 'BTS Number' />
<param name= '[<0-255>]' doc= 'TRX Number' />
</params>
</command>
<command id= 'show timeslot [<0-255>] [<0-255>] [<0-7>]' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'timeslot' doc= 'Display information about a TS' />
<param name= '[<0-255>]' doc= 'BTS Number' />
<param name= '[<0-255>]' doc= 'TRX Number' />
<param name= '[<0-7>]' doc= 'Timeslot Number' />
</params>
</command>
<command id= 'show lchan [<0-255>] [<0-255>] [<0-7>] [<0-7>]' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'lchan' doc= 'Display information about a logical channel' />
<param name= '[<0-255>]' doc= 'BTS Number' />
<param name= '[<0-255>]' doc= 'TRX Number' />
<param name= '[<0-7>]' doc= 'Timeslot Number' />
<param name= '[<0-7>]' doc= 'Logical Channel Number' />
</params>
</command>
<command id= 'show lchan summary [<0-255>] [<0-255>] [<0-7>] [<0-7>]' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'lchan' doc= 'Display information about a logical channel' />
<param name= 'summary' doc= 'Short summary' />
<param name= '[<0-255>]' doc= 'BTS Number' />
<param name= '[<0-255>]' doc= 'TRX Number' />
<param name= '[<0-7>]' doc= 'Timeslot Number' />
<param name= '[<0-7>]' doc= 'Logical Channel Number' />
</params>
</command>
2020-05-29 11:49:03 +00:00
<command id= 'logging filter l1-sapi (unknown|agch|bcch|cbch|facch/f|facch/h|fcch|idle|nch|pacch|pagch|pbcch|pch|pdtch|pnch|ppch|prach|ptcch|rach|sacch|sch|sdcch|tch/f|tch/h)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'filter' doc= 'Filter log messages' />
<param name= 'l1-sapi' doc= 'L1 SAPI' />
<param name= 'unknown' doc= 'UNKNOWN' />
<param name= 'agch' doc= 'AGCH' />
<param name= 'bcch' doc= 'BCCH' />
<param name= 'cbch' doc= 'CBCH' />
<param name= 'facch/f' doc= 'FACCH/F' />
<param name= 'facch/h' doc= 'FACCH/H' />
<param name= 'fcch' doc= 'FCCH' />
<param name= 'idle' doc= 'IDLE' />
<param name= 'nch' doc= 'NCH' />
<param name= 'pacch' doc= 'PACCH' />
<param name= 'pagch' doc= 'PAGCH' />
<param name= 'pbcch' doc= 'PBCCH' />
<param name= 'pch' doc= 'PCH' />
<param name= 'pdtch' doc= 'PDTCH' />
<param name= 'pnch' doc= 'PNCH' />
<param name= 'ppch' doc= 'PPCH' />
<param name= 'prach' doc= 'PRACH' />
<param name= 'ptcch' doc= 'PTCCH' />
<param name= 'rach' doc= 'RACH' />
<param name= 'sacch' doc= 'SACCH' />
<param name= 'sch' doc= 'SCH' />
<param name= 'sdcch' doc= 'SDCCH' />
<param name= 'tch/f' doc= 'TCH/F' />
<param name= 'tch/h' doc= 'TCH/H' />
</params>
</command>
<command id= 'no logging filter l1-sapi (unknown|agch|bcch|cbch|facch/f|facch/h|fcch|idle|nch|pacch|pagch|pbcch|pch|pdtch|pnch|ppch|prach|ptcch|rach|sacch|sch|sdcch|tch/f|tch/h)' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'logging' doc= 'Configure logging' />
<param name= 'filter' doc= 'Filter log messages' />
<param name= 'l1-sapi' doc= 'L1 SAPI' />
<param name= 'unknown' doc= 'UNKNOWN' />
<param name= 'agch' doc= 'AGCH' />
<param name= 'bcch' doc= 'BCCH' />
<param name= 'cbch' doc= 'CBCH' />
<param name= 'facch/f' doc= 'FACCH/F' />
<param name= 'facch/h' doc= 'FACCH/H' />
<param name= 'fcch' doc= 'FCCH' />
<param name= 'idle' doc= 'IDLE' />
<param name= 'nch' doc= 'NCH' />
<param name= 'pacch' doc= 'PACCH' />
<param name= 'pagch' doc= 'PAGCH' />
<param name= 'pbcch' doc= 'PBCCH' />
<param name= 'pch' doc= 'PCH' />
<param name= 'pdtch' doc= 'PDTCH' />
<param name= 'pnch' doc= 'PNCH' />
<param name= 'ppch' doc= 'PPCH' />
<param name= 'prach' doc= 'PRACH' />
<param name= 'ptcch' doc= 'PTCCH' />
<param name= 'rach' doc= 'RACH' />
<param name= 'sacch' doc= 'SACCH' />
<param name= 'sch' doc= 'SCH' />
<param name= 'sdcch' doc= 'SDCCH' />
<param name= 'tch/f' doc= 'TCH/F' />
<param name= 'tch/h' doc= 'TCH/H' />
</params>
</command>
2019-06-19 10:18:24 +00:00
<command id= 'logging enable' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'enable' doc= 'Enables logging to this vty' />
</params>
</command>
<command id= 'logging disable' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'disable' doc= 'Disables logging to this vty' />
</params>
</command>
<command id= 'logging filter all (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'filter' doc= 'Filter log messages' />
<param name= 'all' doc= 'Do you want to log all messages?' />
<param name= '0' doc= 'Only print messages matched by other filters' />
<param name= '1' doc= 'Bypass filter and print all messages' />
</params>
</command>
<command id= 'logging color (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'color' doc= 'Configure color-printing for log messages' />
<param name= '0' doc= 'Don't use color for printing messages' />
<param name= '1' doc= 'Use color for printing messages' />
</params>
</command>
<command id= 'logging timestamp (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'timestamp' doc= 'Configure log message timestamping' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with current timestamp' />
</params>
</command>
<command id= 'logging print extended-timestamp (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'extended-timestamp' doc= 'Configure log message timestamping' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
</params>
</command>
<command id= 'logging print category (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'category' doc= 'Configure log message' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with category/subsystem name' />
</params>
</command>
<command id= 'logging print category-hex (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'category-hex' doc= 'Configure log message' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with category/subsystem nr in hex ('<000b>')' />
</params>
</command>
<command id= 'logging print level (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'level' doc= 'Configure log message' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with the log level name' />
</params>
</command>
<command id= 'logging print file (0|1|basename) [last]' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'file' doc= 'Configure log message' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with the source file and line' />
<param name= 'basename' doc= 'Prefix each log message with the source file's basename (strip leading paths) and line' />
<param name= '[last]' doc= 'Log source file info at the end of a log line. If omitted, log source file info just before the log text.' />
</params>
</command>
<command id= 'logging set-log-mask MASK' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'set-log-mask' doc= 'Set the logmask of this logging target' />
<param name= 'MASK' doc= 'List of logging categories to log, e.g. 'abc:mno:xyz'. Available log categories depend on the specific application, refer to the 'logging level' command. Optionally add individual log levels like 'abc,1:mno,3:xyz,5', where the level numbers are LOGL_DEBUG=1 LOGL_INFO=3 LOGL_NOTICE=5 LOGL_ERROR=7 LOGL_FATAL=8' />
</params>
</command>
<command id= 'logging level (rsl|oml|rll|rr|meas|pag|l1c|l1p|dsp|pcu|ho|trx|loop|abis|rtp|sum|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'level' doc= 'Set the log level for a specified category' />
<param name= 'rsl' doc= 'A-bis Radio Siganlling Link (RSL)' />
<param name= 'oml' doc= 'A-bis Network Management / O&M (NM/OML)' />
<param name= 'rll' doc= 'A-bis Radio Link Layer (RLL)' />
<param name= 'rr' doc= 'Layer3 Radio Resource (RR)' />
<param name= 'meas' doc= 'Radio Measurement Processing' />
<param name= 'pag' doc= 'Paging Subsystem' />
<param name= 'l1c' doc= 'Layer 1 Control (MPH)' />
<param name= 'l1p' doc= 'Layer 1 Primitives (PH)' />
<param name= 'dsp' doc= 'DSP Trace Messages' />
<param name= 'pcu' doc= 'PCU interface' />
<param name= 'ho' doc= 'Handover' />
<param name= 'trx' doc= 'TRX interface' />
<param name= 'loop' doc= 'Control loops' />
<param name= 'abis' doc= 'A-bis Intput Subsystem' />
<param name= 'rtp' doc= 'Realtime Transfer Protocol' />
<param name= 'sum' doc= 'DSUM' />
<param name= 'lglobal' doc= 'Library-internal global log family' />
<param name= 'llapd' doc= 'LAPD in libosmogsm' />
<param name= 'linp' doc= 'A-bis Intput Subsystem' />
<param name= 'lmux' doc= 'A-bis B-Subchannel TRAU Frame Multiplex' />
<param name= 'lmi' doc= 'A-bis Input Driver for Signalling' />
<param name= 'lmib' doc= 'A-bis Input Driver for B-Channels (voice)' />
<param name= 'lsms' doc= 'Layer3 Short Message Service (SMS)' />
<param name= 'lctrl' doc= 'Control Interface' />
<param name= 'lgtp' doc= 'GPRS GTP library' />
<param name= 'lstats' doc= 'Statistics messages and logging' />
<param name= 'lgsup' doc= 'Generic Subscriber Update Protocol' />
<param name= 'loap' doc= 'Osmocom Authentication Protocol' />
<param name= 'lss7' doc= 'libosmo-sigtran Signalling System 7' />
<param name= 'lsccp' doc= 'libosmo-sigtran SCCP Implementation' />
<param name= 'lsua' doc= 'libosmo-sigtran SCCP User Adaptation' />
<param name= 'lm3ua' doc= 'libosmo-sigtran MTP3 User Adaptation' />
<param name= 'lmgcp' doc= 'libosmo-mgcp Media Gateway Control Protocol' />
<param name= 'ljibuf' doc= 'libosmo-netif Jitter Buffer' />
<param name= 'lrspro' doc= 'Remote SIM protocol' />
<param name= 'debug' doc= 'Log debug messages and higher levels' />
<param name= 'info' doc= 'Log informational messages and higher levels' />
<param name= 'notice' doc= 'Log noticeable messages and higher levels' />
<param name= 'error' doc= 'Log error messages and higher levels' />
<param name= 'fatal' doc= 'Log only fatal messages' />
</params>
</command>
<command id= 'logging level set-all (debug|info|notice|error|fatal)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'level' doc= 'Set the log level for a specified category' />
<param name= 'set-all' doc= 'Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' />
<param name= 'debug' doc= 'Log debug messages and higher levels' />
<param name= 'info' doc= 'Log informational messages and higher levels' />
<param name= 'notice' doc= 'Log noticeable messages and higher levels' />
<param name= 'error' doc= 'Log error messages and higher levels' />
<param name= 'fatal' doc= 'Log only fatal messages' />
</params>
</command>
<command id= 'logging level force-all (debug|info|notice|error|fatal)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'level' doc= 'Set the log level for a specified category' />
<param name= 'force-all' doc= 'Globally force all logging categories to a specific level. This is released by the 'no logging level force-all' command. Note: any 'logging level <category> <level>' commands will have no visible effect after this, until the forced level is released.' />
<param name= 'debug' doc= 'Log debug messages and higher levels' />
<param name= 'info' doc= 'Log informational messages and higher levels' />
<param name= 'notice' doc= 'Log noticeable messages and higher levels' />
<param name= 'error' doc= 'Log error messages and higher levels' />
<param name= 'fatal' doc= 'Log only fatal messages' />
</params>
</command>
<command id= 'no logging level force-all' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'logging' doc= 'Configure logging' />
<param name= 'level' doc= 'Set the log level for a specified category' />
<param name= 'force-all' doc= 'Release any globally forced log level set with 'logging level force-all <level>'' />
</params>
</command>
2020-05-29 11:49:03 +00:00
<command id= 'logp (rsl|oml|rll|rr|meas|pag|l1c|l1p|dsp|pcu|ho|trx|loop|abis|rtp|sum|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal) .LOGMESSAGE' >
<params >
<param name= 'logp' doc= 'Print a message on all log outputs; useful for placing markers in test logs' />
<param name= 'rsl' doc= 'A-bis Radio Siganlling Link (RSL)' />
<param name= 'oml' doc= 'A-bis Network Management / O&M (NM/OML)' />
<param name= 'rll' doc= 'A-bis Radio Link Layer (RLL)' />
<param name= 'rr' doc= 'Layer3 Radio Resource (RR)' />
<param name= 'meas' doc= 'Radio Measurement Processing' />
<param name= 'pag' doc= 'Paging Subsystem' />
<param name= 'l1c' doc= 'Layer 1 Control (MPH)' />
<param name= 'l1p' doc= 'Layer 1 Primitives (PH)' />
<param name= 'dsp' doc= 'DSP Trace Messages' />
<param name= 'pcu' doc= 'PCU interface' />
<param name= 'ho' doc= 'Handover' />
<param name= 'trx' doc= 'TRX interface' />
<param name= 'loop' doc= 'Control loops' />
<param name= 'abis' doc= 'A-bis Intput Subsystem' />
<param name= 'rtp' doc= 'Realtime Transfer Protocol' />
<param name= 'sum' doc= 'DSUM' />
<param name= 'lglobal' doc= 'Library-internal global log family' />
<param name= 'llapd' doc= 'LAPD in libosmogsm' />
<param name= 'linp' doc= 'A-bis Intput Subsystem' />
<param name= 'lmux' doc= 'A-bis B-Subchannel TRAU Frame Multiplex' />
<param name= 'lmi' doc= 'A-bis Input Driver for Signalling' />
<param name= 'lmib' doc= 'A-bis Input Driver for B-Channels (voice)' />
<param name= 'lsms' doc= 'Layer3 Short Message Service (SMS)' />
<param name= 'lctrl' doc= 'Control Interface' />
<param name= 'lgtp' doc= 'GPRS GTP library' />
<param name= 'lstats' doc= 'Statistics messages and logging' />
<param name= 'lgsup' doc= 'Generic Subscriber Update Protocol' />
<param name= 'loap' doc= 'Osmocom Authentication Protocol' />
<param name= 'lss7' doc= 'libosmo-sigtran Signalling System 7' />
<param name= 'lsccp' doc= 'libosmo-sigtran SCCP Implementation' />
<param name= 'lsua' doc= 'libosmo-sigtran SCCP User Adaptation' />
<param name= 'lm3ua' doc= 'libosmo-sigtran MTP3 User Adaptation' />
<param name= 'lmgcp' doc= 'libosmo-mgcp Media Gateway Control Protocol' />
<param name= 'ljibuf' doc= 'libosmo-netif Jitter Buffer' />
<param name= 'lrspro' doc= 'Remote SIM protocol' />
<param name= 'debug' doc= 'Log debug messages and higher levels' />
<param name= 'info' doc= 'Log informational messages and higher levels' />
<param name= 'notice' doc= 'Log noticeable messages and higher levels' />
<param name= 'error' doc= 'Log error messages and higher levels' />
<param name= 'fatal' doc= 'Log only fatal messages' />
<param name= '.LOGMESSAGE' doc= 'Arbitrary message to log on given category and log level' />
</params>
</command>
2019-06-19 10:18:24 +00:00
<command id= 'show logging vty' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'logging' doc= 'Show current logging configuration' />
<param name= 'vty' doc= 'Show current logging configuration for this vty' />
</params>
</command>
<command id= 'show alarms' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'alarms' doc= 'Show current logging configuration' />
</params>
</command>
<command id= 'show talloc-context (application|all) (full|brief|DEPTH)' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'talloc-context' doc= 'Show talloc memory hierarchy' />
<param name= 'application' doc= 'Application's context' />
<param name= 'all' doc= 'All contexts, if NULL-context tracking is enabled' />
<param name= 'full' doc= 'Display a full talloc memory hierarchy' />
<param name= 'brief' doc= 'Display a brief talloc memory hierarchy' />
<param name= 'DEPTH' doc= 'Specify required maximal depth value' />
</params>
</command>
<command id= 'show talloc-context (application|all) (full|brief|DEPTH) tree ADDRESS' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'talloc-context' doc= 'Show talloc memory hierarchy' />
<param name= 'application' doc= 'Application's context' />
<param name= 'all' doc= 'All contexts, if NULL-context tracking is enabled' />
<param name= 'full' doc= 'Display a full talloc memory hierarchy' />
<param name= 'brief' doc= 'Display a brief talloc memory hierarchy' />
<param name= 'DEPTH' doc= 'Specify required maximal depth value' />
<param name= 'tree' doc= 'Display only a specific memory chunk' />
<param name= 'ADDRESS' doc= 'Chunk address (e.g. 0xdeadbeef)' />
</params>
</command>
<command id= 'show talloc-context (application|all) (full|brief|DEPTH) filter REGEXP' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'talloc-context' doc= 'Show talloc memory hierarchy' />
<param name= 'application' doc= 'Application's context' />
<param name= 'all' doc= 'All contexts, if NULL-context tracking is enabled' />
<param name= 'full' doc= 'Display a full talloc memory hierarchy' />
<param name= 'brief' doc= 'Display a brief talloc memory hierarchy' />
<param name= 'DEPTH' doc= 'Specify required maximal depth value' />
<param name= 'filter' doc= 'Filter chunks using regular expression' />
<param name= 'REGEXP' doc= 'Regular expression' />
</params>
</command>
<command id= 'show stats' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'stats' doc= 'Show statistical values' />
</params>
</command>
<command id= 'show stats level (global|peer|subscriber)' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'stats' doc= 'Show statistical values' />
<param name= 'level' doc= 'Set the maximum group level' />
<param name= 'global' doc= 'Show global groups only' />
<param name= 'peer' doc= 'Show global and network peer related groups' />
<param name= 'subscriber' doc= 'Show global, peer, and subscriber groups' />
</params>
</command>
<command id= 'show asciidoc counters' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'asciidoc' doc= 'Asciidoc generation' />
<param name= 'counters' doc= 'Generate table of all registered counters' />
</params>
</command>
<command id= 'show rate-counters' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'rate-counters' doc= 'Show all rate counters' />
</params>
</command>
<command id= 'bts <0-0> trx <0-0> ts <0-7> lchan <0-1> rtp jitter-buffer <0-10000>' >
<params >
<param name= 'bts' doc= 'BTS related commands' />
<param name= '<0-0>' doc= 'BTS number' />
<param name= 'trx' doc= 'TRX related commands' />
<param name= '<0-0>' doc= 'TRX number' />
<param name= 'ts' doc= 'timeslot related commands' />
<param name= '<0-7>' doc= 'timeslot number' />
<param name= 'lchan' doc= 'logical channel commands' />
<param name= '<0-1>' doc= 'logical channel number' />
<param name= 'rtp' doc= 'RTP settings' />
<param name= 'jitter-buffer' doc= 'Jitter buffer' />
<param name= '<0-10000>' doc= 'Size of jitter buffer in (ms)' />
</params>
</command>
<command id= 'bts <0-0> trx <0-0> ts <0-7> lchan <0-1> loopback' >
<params >
<param name= 'bts' doc= 'BTS related commands' />
<param name= '<0-0>' doc= 'BTS number' />
<param name= 'trx' doc= 'TRX related commands' />
<param name= '<0-0>' doc= 'TRX number' />
<param name= 'ts' doc= 'timeslot related commands' />
<param name= '<0-7>' doc= 'timeslot number' />
<param name= 'lchan' doc= 'logical channel commands' />
<param name= '<0-1>' doc= 'logical channel number' />
<param name= 'loopback' doc= 'Set loopback' />
</params>
</command>
<command id= 'no bts <0-0> trx <0-0> ts <0-7> lchan <0-1> loopback' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'bts' doc= 'BTS related commands' />
<param name= '<0-0>' doc= 'BTS number' />
<param name= 'trx' doc= 'TRX related commands' />
<param name= '<0-0>' doc= 'TRX number' />
<param name= 'ts' doc= 'timeslot related commands' />
<param name= '<0-7>' doc= 'timeslot number' />
<param name= 'lchan' doc= 'logical channel commands' />
<param name= '<0-1>' doc= 'logical channel number' />
<param name= 'loopback' doc= 'Set loopback' />
</params>
</command>
2020-05-29 11:49:03 +00:00
<command id= 'test send-failure-event-report <0-255>' >
<params >
<param name= 'test' doc= 'Various testing commands' />
<param name= 'send-failure-event-report' doc= 'Send a test OML failure event report to the BSC' />
<param name= '<0-255>' doc= 'BTS Number' />
</params>
</command>
2019-06-19 10:18:24 +00:00
</node>
<node id= 'config' >
<name > config</name>
<command id= 'hostname WORD' >
<params >
<param name= 'hostname' doc= 'Set system's network name' />
<param name= 'WORD' doc= 'This system's network name' />
</params>
</command>
<command id= 'no hostname [HOSTNAME]' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'hostname' doc= 'Reset system's network name' />
<param name= '[HOSTNAME]' doc= 'Host name of this router' />
</params>
</command>
<command id= 'password (8|) WORD' >
<params >
<param name= 'password' doc= 'Assign the terminal connection password' />
<param name= '8' doc= 'Specifies a HIDDEN password will follow' />
<param name= '' doc= 'dummy string ' />
<param name= 'WORD' doc= 'The HIDDEN line password string' />
</params>
</command>
<command id= 'password LINE' >
<params >
<param name= 'password' doc= 'Assign the terminal connection password' />
<param name= 'LINE' doc= 'The UNENCRYPTED (cleartext) line password' />
</params>
</command>
<command id= 'enable password (8|) WORD' >
<params >
<param name= 'enable' doc= 'Modify enable password parameters' />
<param name= 'password' doc= 'Assign the privileged level password' />
<param name= '8' doc= 'Specifies a HIDDEN password will follow' />
<param name= '' doc= 'dummy string ' />
<param name= 'WORD' doc= 'The HIDDEN 'enable' password string' />
</params>
</command>
<command id= 'enable password LINE' >
<params >
<param name= 'enable' doc= 'Modify enable password parameters' />
<param name= 'password' doc= 'Assign the privileged level password' />
<param name= 'LINE' doc= 'The UNENCRYPTED (cleartext) 'enable' password' />
</params>
</command>
<command id= 'no enable password' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'enable' doc= 'Modify enable password parameters' />
<param name= 'password' doc= 'Assign the privileged level password' />
</params>
</command>
<command id= 'banner motd default' >
<params >
<param name= 'banner' doc= 'Set banner string' />
<param name= 'motd' doc= 'Strings for motd' />
<param name= 'default' doc= 'Default string' />
</params>
</command>
<command id= 'banner motd file [FILE]' >
<params >
<param name= 'banner' doc= 'Set banner' />
<param name= 'motd' doc= 'Banner for motd' />
<param name= 'file' doc= 'Banner from a file' />
<param name= '[FILE]' doc= 'Filename' />
</params>
</command>
<command id= 'no banner motd' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'banner' doc= 'Set banner string' />
<param name= 'motd' doc= 'Strings for motd' />
</params>
</command>
<command id= 'service terminal-length <0-512>' >
<params >
<param name= 'service' doc= 'Set up miscellaneous service' />
<param name= 'terminal-length' doc= 'System wide terminal length configuration' />
<param name= '<0-512>' doc= 'Number of lines of VTY (0 means no line control)' />
</params>
</command>
<command id= 'no service terminal-length [<0-512>]' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'service' doc= 'Set up miscellaneous service' />
<param name= 'terminal-length' doc= 'System wide terminal length configuration' />
<param name= '[<0-512>]' doc= 'Number of lines of VTY (0 means no line control)' />
</params>
</command>
<command id= 'line vty' >
<params >
<param name= 'line' doc= 'Configure a terminal line' />
<param name= 'vty' doc= 'Virtual terminal' />
</params>
</command>
<command id= 'service advanced-vty' >
<params >
<param name= 'service' doc= 'Set up miscellaneous service' />
<param name= 'advanced-vty' doc= 'Enable advanced mode vty interface' />
</params>
</command>
<command id= 'no service advanced-vty' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'service' doc= 'Set up miscellaneous service' />
<param name= 'advanced-vty' doc= 'Enable advanced mode vty interface' />
</params>
</command>
<command id= 'show history' >
<params >
<param name= 'show' doc= 'Show running system information' />
<param name= 'history' doc= 'Display the session command history' />
</params>
</command>
<command id= 'ctrl' >
<params >
<param name= 'ctrl' doc= 'Configure the Control Interface' />
</params>
</command>
<command id= 'e1_input' >
<params >
<param name= 'e1_input' doc= 'Configure E1/T1/J1 TDM input' />
</params>
</command>
<command id= 'log stderr' >
<params >
<param name= 'log' doc= 'Configure logging sub-system' />
<param name= 'stderr' doc= 'Logging via STDERR of the process' />
</params>
</command>
<command id= 'no log stderr' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'log' doc= 'Configure logging sub-system' />
<param name= 'stderr' doc= 'Logging via STDERR of the process' />
</params>
</command>
<command id= 'log file .FILENAME' >
<params >
<param name= 'log' doc= 'Configure logging sub-system' />
<param name= 'file' doc= 'Logging to text file' />
<param name= '.FILENAME' doc= 'Filename' />
</params>
</command>
<command id= 'no log file .FILENAME' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'log' doc= 'Configure logging sub-system' />
<param name= 'file' doc= 'Logging to text file' />
<param name= '.FILENAME' doc= 'Filename' />
</params>
</command>
<command id= 'log alarms <2-32700>' >
<params >
<param name= 'log' doc= 'Configure logging sub-system' />
<param name= 'alarms' doc= 'Logging alarms to osmo_strrb' />
<param name= '<2-32700>' doc= 'Maximum number of messages to log' />
</params>
</command>
<command id= 'no log alarms' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'log' doc= 'Configure logging sub-system' />
<param name= 'alarms' doc= 'Logging alarms to osmo_strrb' />
</params>
</command>
<command id= 'log syslog (authpriv|cron|daemon|ftp|lpr|mail|news|user|uucp)' >
<params >
<param name= 'log' doc= 'Configure logging sub-system' />
<param name= 'syslog' doc= 'Logging via syslog' />
<param name= 'authpriv' doc= 'Security/authorization messages facility' />
<param name= 'cron' doc= 'Clock daemon (cron/at) facility' />
<param name= 'daemon' doc= 'General system daemon facility' />
<param name= 'ftp' doc= 'Ftp daemon facility' />
<param name= 'lpr' doc= 'Line printer facility' />
<param name= 'mail' doc= 'Mail facility' />
<param name= 'news' doc= 'News facility' />
<param name= 'user' doc= 'Generic facility' />
<param name= 'uucp' doc= 'UUCP facility' />
</params>
</command>
<command id= 'log syslog local <0-7>' >
<params >
<param name= 'log' doc= 'Configure logging sub-system' />
<param name= 'syslog' doc= 'Logging via syslog' />
<param name= 'local' doc= 'Syslog LOCAL facility' />
<param name= '<0-7>' doc= 'Local facility number' />
</params>
</command>
<command id= 'no log syslog' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'log' doc= 'Configure logging sub-system' />
<param name= 'syslog' doc= 'Logging via syslog' />
</params>
</command>
<command id= 'log gsmtap [HOSTNAME]' >
<params >
<param name= 'log' doc= 'Configure logging sub-system' />
<param name= 'gsmtap' doc= 'Logging via GSMTAP' />
<param name= '[HOSTNAME]' doc= 'Host name to send the GSMTAP logging to (UDP port 4729)' />
</params>
</command>
<command id= 'stats reporter statsd' >
<params >
<param name= 'stats' doc= 'Configure stats sub-system' />
<param name= 'reporter' doc= 'Configure a stats reporter' />
<param name= 'statsd' doc= 'Report to a STATSD server' />
</params>
</command>
<command id= 'no stats reporter statsd' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'stats' doc= 'Configure stats sub-system' />
<param name= 'reporter' doc= 'Configure a stats reporter' />
<param name= 'statsd' doc= 'Report to a STATSD server' />
</params>
</command>
<command id= 'stats reporter log' >
<params >
<param name= 'stats' doc= 'Configure stats sub-system' />
<param name= 'reporter' doc= 'Configure a stats reporter' />
<param name= 'log' doc= 'Report to the logger' />
</params>
</command>
<command id= 'no stats reporter log' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'stats' doc= 'Configure stats sub-system' />
<param name= 'reporter' doc= 'Configure a stats reporter' />
<param name= 'log' doc= 'Report to the logger' />
</params>
</command>
<command id= 'stats interval <1-65535>' >
<params >
<param name= 'stats' doc= 'Configure stats sub-system' />
<param name= 'interval' doc= 'Set the reporting interval' />
<param name= '<1-65535>' doc= 'Interval in seconds' />
</params>
</command>
<command id= 'bts BTS_NR' >
<params >
<param name= 'bts' doc= 'Select a BTS to configure' />
<param name= 'BTS_NR' doc= 'BTS Number' />
</params>
</command>
<command id= 'vty telnet-port <0-65535>' >
<params >
<param name= 'vty' doc= 'Configure the VTY' />
<param name= 'telnet-port' doc= 'Set the VTY telnet port' />
<param name= '<0-65535>' doc= 'TCP Port number' />
</params>
</command>
<command id= 'phy <0-255>' >
<params >
<param name= 'phy' doc= 'Select a PHY to configure' />
<param name= '<0-255>' doc= 'PHY number' />
</params>
</command>
</node>
<node id= 'config-log' >
<name > config-log</name>
<command id= 'logging filter all (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'filter' doc= 'Filter log messages' />
<param name= 'all' doc= 'Do you want to log all messages?' />
<param name= '0' doc= 'Only print messages matched by other filters' />
<param name= '1' doc= 'Bypass filter and print all messages' />
</params>
</command>
<command id= 'logging color (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'color' doc= 'Configure color-printing for log messages' />
<param name= '0' doc= 'Don't use color for printing messages' />
<param name= '1' doc= 'Use color for printing messages' />
</params>
</command>
<command id= 'logging timestamp (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'timestamp' doc= 'Configure log message timestamping' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with current timestamp' />
</params>
</command>
<command id= 'logging print extended-timestamp (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'extended-timestamp' doc= 'Configure log message timestamping' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
</params>
</command>
<command id= 'logging print category (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'category' doc= 'Configure log message' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with category/subsystem name' />
</params>
</command>
<command id= 'logging print category-hex (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'category-hex' doc= 'Configure log message' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with category/subsystem nr in hex ('<000b>')' />
</params>
</command>
<command id= 'logging print level (0|1)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'level' doc= 'Configure log message' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with the log level name' />
</params>
</command>
<command id= 'logging print file (0|1|basename) [last]' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'print' doc= 'Log output settings' />
<param name= 'file' doc= 'Configure log message' />
<param name= '0' doc= 'Don't prefix each log message' />
<param name= '1' doc= 'Prefix each log message with the source file and line' />
<param name= 'basename' doc= 'Prefix each log message with the source file's basename (strip leading paths) and line' />
<param name= '[last]' doc= 'Log source file info at the end of a log line. If omitted, log source file info just before the log text.' />
</params>
</command>
<command id= 'logging level (rsl|oml|rll|rr|meas|pag|l1c|l1p|dsp|pcu|ho|trx|loop|abis|rtp|sum|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'level' doc= 'Set the log level for a specified category' />
<param name= 'rsl' doc= 'A-bis Radio Siganlling Link (RSL)' />
<param name= 'oml' doc= 'A-bis Network Management / O&M (NM/OML)' />
<param name= 'rll' doc= 'A-bis Radio Link Layer (RLL)' />
<param name= 'rr' doc= 'Layer3 Radio Resource (RR)' />
<param name= 'meas' doc= 'Radio Measurement Processing' />
<param name= 'pag' doc= 'Paging Subsystem' />
<param name= 'l1c' doc= 'Layer 1 Control (MPH)' />
<param name= 'l1p' doc= 'Layer 1 Primitives (PH)' />
<param name= 'dsp' doc= 'DSP Trace Messages' />
<param name= 'pcu' doc= 'PCU interface' />
<param name= 'ho' doc= 'Handover' />
<param name= 'trx' doc= 'TRX interface' />
<param name= 'loop' doc= 'Control loops' />
<param name= 'abis' doc= 'A-bis Intput Subsystem' />
<param name= 'rtp' doc= 'Realtime Transfer Protocol' />
<param name= 'sum' doc= 'DSUM' />
<param name= 'lglobal' doc= 'Library-internal global log family' />
<param name= 'llapd' doc= 'LAPD in libosmogsm' />
<param name= 'linp' doc= 'A-bis Intput Subsystem' />
<param name= 'lmux' doc= 'A-bis B-Subchannel TRAU Frame Multiplex' />
<param name= 'lmi' doc= 'A-bis Input Driver for Signalling' />
<param name= 'lmib' doc= 'A-bis Input Driver for B-Channels (voice)' />
<param name= 'lsms' doc= 'Layer3 Short Message Service (SMS)' />
<param name= 'lctrl' doc= 'Control Interface' />
<param name= 'lgtp' doc= 'GPRS GTP library' />
<param name= 'lstats' doc= 'Statistics messages and logging' />
<param name= 'lgsup' doc= 'Generic Subscriber Update Protocol' />
<param name= 'loap' doc= 'Osmocom Authentication Protocol' />
<param name= 'lss7' doc= 'libosmo-sigtran Signalling System 7' />
<param name= 'lsccp' doc= 'libosmo-sigtran SCCP Implementation' />
<param name= 'lsua' doc= 'libosmo-sigtran SCCP User Adaptation' />
<param name= 'lm3ua' doc= 'libosmo-sigtran MTP3 User Adaptation' />
<param name= 'lmgcp' doc= 'libosmo-mgcp Media Gateway Control Protocol' />
<param name= 'ljibuf' doc= 'libosmo-netif Jitter Buffer' />
<param name= 'lrspro' doc= 'Remote SIM protocol' />
<param name= 'debug' doc= 'Log debug messages and higher levels' />
<param name= 'info' doc= 'Log informational messages and higher levels' />
<param name= 'notice' doc= 'Log noticeable messages and higher levels' />
<param name= 'error' doc= 'Log error messages and higher levels' />
<param name= 'fatal' doc= 'Log only fatal messages' />
</params>
</command>
<command id= 'logging level set-all (debug|info|notice|error|fatal)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'level' doc= 'Set the log level for a specified category' />
<param name= 'set-all' doc= 'Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' />
<param name= 'debug' doc= 'Log debug messages and higher levels' />
<param name= 'info' doc= 'Log informational messages and higher levels' />
<param name= 'notice' doc= 'Log noticeable messages and higher levels' />
<param name= 'error' doc= 'Log error messages and higher levels' />
<param name= 'fatal' doc= 'Log only fatal messages' />
</params>
</command>
<command id= 'logging level force-all (debug|info|notice|error|fatal)' >
<params >
<param name= 'logging' doc= 'Configure logging' />
<param name= 'level' doc= 'Set the log level for a specified category' />
<param name= 'force-all' doc= 'Globally force all logging categories to a specific level. This is released by the 'no logging level force-all' command. Note: any 'logging level <category> <level>' commands will have no visible effect after this, until the forced level is released.' />
<param name= 'debug' doc= 'Log debug messages and higher levels' />
<param name= 'info' doc= 'Log informational messages and higher levels' />
<param name= 'notice' doc= 'Log noticeable messages and higher levels' />
<param name= 'error' doc= 'Log error messages and higher levels' />
<param name= 'fatal' doc= 'Log only fatal messages' />
</params>
</command>
<command id= 'no logging level force-all' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'logging' doc= 'Configure logging' />
<param name= 'level' doc= 'Set the log level for a specified category' />
<param name= 'force-all' doc= 'Release any globally forced log level set with 'logging level force-all <level>'' />
</params>
</command>
</node>
<node id= 'config-stats' >
<name > config-stats</name>
<command id= 'local-ip ADDR' >
<params >
<param name= 'local-ip' doc= 'Set the IP address to which we bind locally' />
<param name= 'ADDR' doc= 'IP Address' />
</params>
</command>
<command id= 'no local-ip' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'local-ip' doc= 'Set the IP address to which we bind locally' />
</params>
</command>
<command id= 'remote-ip ADDR' >
<params >
<param name= 'remote-ip' doc= 'Set the remote IP address to which we connect' />
<param name= 'ADDR' doc= 'IP Address' />
</params>
</command>
<command id= 'remote-port <1-65535>' >
<params >
<param name= 'remote-port' doc= 'Set the remote port to which we connect' />
<param name= '<1-65535>' doc= 'Remote port number' />
</params>
</command>
<command id= 'mtu <100-65535>' >
<params >
<param name= 'mtu' doc= 'Set the maximum packet size' />
<param name= '<100-65535>' doc= 'Size in byte' />
</params>
</command>
<command id= 'no mtu' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'mtu' doc= 'Set the maximum packet size' />
</params>
</command>
<command id= 'prefix PREFIX' >
<params >
<param name= 'prefix' doc= 'Set the item name prefix' />
<param name= 'PREFIX' doc= 'The prefix string' />
</params>
</command>
<command id= 'no prefix' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'prefix' doc= 'Set the item name prefix' />
</params>
</command>
<command id= 'level (global|peer|subscriber)' >
<params >
<param name= 'level' doc= 'Set the maximum group level' />
<param name= 'global' doc= 'Report global groups only' />
<param name= 'peer' doc= 'Report global and network peer related groups' />
<param name= 'subscriber' doc= 'Report global, peer, and subscriber groups' />
</params>
</command>
<command id= 'enable' >
<params >
<param name= 'enable' doc= 'Enable the reporter' />
</params>
</command>
<command id= 'disable' >
<params >
<param name= 'disable' doc= 'Disable the reporter' />
</params>
</command>
2020-05-29 11:49:03 +00:00
<command id= 'flush-period <0-65535>' >
<params >
<param name= 'flush-period' doc= 'Configure stats sub-system' />
<param name= '<0-65535>' doc= 'Send all stats even if they have not changed (i.e. force the flush)every N-th reporting interval. Set to 0 to disable regular flush (default).' />
</params>
</command>
2019-06-19 10:18:24 +00:00
</node>
<node id= 'config-line' >
<name > config-line</name>
<command id= 'login' >
<params >
<param name= 'login' doc= 'Enable password checking' />
</params>
</command>
<command id= 'no login' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'login' doc= 'Enable password checking' />
</params>
</command>
<command id= 'bind A.B.C.D [<0-65535>]' >
<params >
<param name= 'bind' doc= 'Accept VTY telnet connections on local interface' />
<param name= 'A.B.C.D' doc= 'Local interface IP address (default: 127.0.0.1)' />
<param name= '[<0-65535>]' doc= 'Local TCP port number' />
</params>
</command>
</node>
<node id= 'config-e1_input' >
<name > config-e1_input</name>
2020-05-29 11:49:03 +00:00
<command id= 'pcap .FILE' >
<params >
<param name= 'pcap' doc= 'Setup a pcap recording of all E1 traffic' />
<param name= '.FILE' doc= 'Filename to save the packets to' />
</params>
</command>
<command id= 'no pcap' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'pcap' doc= 'Disable pcap recording of all E1 traffic' />
</params>
</command>
<command id= 'e1_line <0-255> driver (misdn|misdn_lapd|dahdi|e1d|ipa|unixsocket)' >
2019-06-19 10:18:24 +00:00
<params >
<param name= 'e1_line' doc= 'Configure E1/T1/J1 Line' />
<param name= '<0-255>' doc= 'Line Number' />
<param name= 'driver' doc= 'Set driver for this line' />
<param name= 'misdn' doc= 'mISDN supported E1 Card (kernel LAPD)' />
<param name= 'misdn_lapd' doc= 'mISDN supported E1 Card (userspace LAPD)' />
<param name= 'dahdi' doc= 'DAHDI supported E1/T1/J1 Card' />
2020-05-29 11:49:03 +00:00
<param name= 'e1d' doc= 'IPA TCP/IP input' />
<param name= 'ipa' doc= 'HSL TCP/IP input' />
<param name= 'unixsocket' doc= 'Unix socket input' />
2019-06-19 10:18:24 +00:00
</params>
</command>
<command id= 'e1_line <0-255> port <0-255>' >
<params >
<param name= 'e1_line' doc= 'Configure E1/T1/J1 Line' />
<param name= '<0-255>' doc= 'Line Number' />
<param name= 'port' doc= 'Set physical port/span/card number' />
<param name= '<0-255>' doc= 'E1/T1 Port/Span/Card number' />
</params>
</command>
<command id= 'e1_line <0-255> socket .SOCKET' >
<params >
<param name= 'e1_line' doc= 'Configure E1/T1/J1 Line' />
<param name= '<0-255>' doc= 'Line Number' />
<param name= 'socket' doc= 'Set socket path for unixsocket' />
<param name= '.SOCKET' doc= 'socket path' />
</params>
</command>
<command id= 'e1_line <0-255> name .LINE' >
<params >
<param name= 'e1_line' doc= 'Configure E1/T1/J1 Line' />
<param name= '<0-255>' doc= 'Line Number' />
<param name= 'name' doc= 'Set name for this line' />
<param name= '.LINE' doc= 'Human readable name' />
</params>
</command>
<command id= 'e1_line <0-255> keepalive' >
<params >
<param name= 'e1_line' doc= 'Configure E1/T1/J1 Line' />
<param name= '<0-255>' doc= 'Line Number' />
<param name= 'keepalive' doc= 'Enable keep-alive probing' />
</params>
</command>
<command id= 'e1_line <0-255> keepalive <1-300> <1-20> <1-300>' >
<params >
<param name= 'e1_line' doc= 'Configure E1/T1/J1 Line' />
<param name= '<0-255>' doc= 'Line Number' />
<param name= 'keepalive' doc= 'Enable keep-alive probing' />
<param name= '<1-300>' doc= 'Idle interval in seconds before probes are sent' />
<param name= '<1-20>' doc= 'Number of probes to sent' />
<param name= '<1-300>' doc= 'Delay between probe packets in seconds' />
</params>
</command>
<command id= 'no e1_line <0-255> keepalive' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'e1_line' doc= 'Configure E1/T1/J1 Line' />
<param name= '<0-255>' doc= 'Line Number' />
<param name= 'keepalive' doc= 'Enable keep-alive probing' />
</params>
</command>
2020-05-29 11:49:03 +00:00
<command id= 'e1_line <0-255> ipa-keepalive <1-300> <1-300>' >
<params >
<param name= 'e1_line' doc= 'Configure E1/T1/J1 Line' />
<param name= '<0-255>' doc= 'Line Number' />
<param name= 'ipa-keepalive' doc= 'Enable IPA PING/PONG keep-alive' />
<param name= '<1-300>' doc= 'Idle interval in seconds before probes are sent' />
<param name= '<1-300>' doc= 'Time to wait for PONG response' />
</params>
</command>
<command id= 'no e1_line <0-255> ipa-keepalive' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'e1_line' doc= 'Configure E1/T1/J1 Line' />
<param name= '<0-255>' doc= 'Line Number' />
<param name= 'ipa-keepalive' doc= 'Enable IPA PING/PONG keep-alive' />
</params>
</command>
2019-06-19 10:18:24 +00:00
<command id= 'ipa bind A.B.C.D' >
<params >
<param name= 'ipa' doc= 'ipa driver config' />
<param name= 'bind' doc= 'Set ipa local bind address' />
<param name= 'A.B.C.D' doc= 'Listen on this IP address (default 0.0.0.0)' />
</params>
</command>
</node>
<node id= 'config-ctrl' >
<name > config-ctrl</name>
<command id= 'bind A.B.C.D' >
<params >
<param name= 'bind' doc= 'Set bind address to listen for Control connections' />
<param name= 'A.B.C.D' doc= 'Local IP address (default 127.0.0.1)' />
</params>
</command>
</node>
<node id= 'phy' >
<name > phy</name>
<command id= 'instance <0-255>' >
<params >
<param name= 'instance' doc= 'Select a PHY instance to configure' />
<param name= '<0-255>' doc= 'PHY Instance number' />
</params>
</command>
<command id= 'no instance <0-255>' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'instance' doc= 'Select a PHY instance to remove' />
<param name= '<0-255>' doc= 'PHY Instance number' />
</params>
</command>
<command id= 'virtual-um ms-multicast-group GROUP' >
<params >
<param name= 'virtual-um' doc= 'Virtual Um layer' />
<param name= 'ms-multicast-group' doc= 'Configure the MS multicast group' />
<param name= 'GROUP' doc= '(null)' />
</params>
</command>
<command id= 'virtual-um ms-udp-port <0-65535>' >
<params >
<param name= 'virtual-um' doc= 'Virtual Um layer' />
<param name= 'ms-udp-port' doc= 'Configure the MS UDP port' />
<param name= '<0-65535>' doc= '(null)' />
</params>
</command>
<command id= 'virtual-um bts-multicast-group GROUP' >
<params >
<param name= 'virtual-um' doc= 'Virtual Um layer' />
<param name= 'bts-multicast-group' doc= 'Configure the BTS multicast group' />
<param name= 'GROUP' doc= '(null)' />
</params>
</command>
<command id= 'virtual-um bts-udp-port <0-65535>' >
<params >
<param name= 'virtual-um' doc= 'Virtual Um layer' />
<param name= 'bts-udp-port' doc= 'Configure the BTS UDP port' />
<param name= '<0-65535>' doc= '(null)' />
</params>
</command>
<command id= 'virtual-um net-device NETDEV' >
<params >
<param name= 'virtual-um' doc= 'Virtual Um layer' />
<param name= 'net-device' doc= 'Configure the network device' />
<param name= 'NETDEV' doc= '(null)' />
</params>
</command>
2020-05-29 11:49:03 +00:00
<command id= 'virtual-um ttl <0-255>' >
<params >
<param name= 'virtual-um' doc= 'Virtual Um layer' />
<param name= 'ttl' doc= 'Configure the TTL for transmitted multicast GSMTAP packets' />
<param name= '<0-255>' doc= '(null)' />
</params>
</command>
2019-06-19 10:18:24 +00:00
</node>
<node id= 'phy-inst' >
<name > phy-inst</name>
</node>
<node id= 'bts' >
<name > bts</name>
<command id= 'ipa unit-id <0-65534> <0-255>' >
<params >
<param name= 'ipa' doc= 'ip.access RSL commands' />
<param name= 'unit-id' doc= 'Set the Unit ID of this BTS' />
<param name= '<0-65534>' doc= 'Site ID' />
<param name= '<0-255>' doc= 'Unit ID' />
</params>
</command>
<command id= 'oml remote-ip A.B.C.D' >
<params >
<param name= 'oml' doc= 'OML Parameters' />
<param name= 'remote-ip' doc= 'OML IP Address' />
<param name= 'A.B.C.D' doc= 'OML IP Address' />
</params>
</command>
<command id= 'rtp jitter-buffer <0-10000> [adaptive]' >
<params >
<param name= 'rtp' doc= 'RTP parameters' />
<param name= 'jitter-buffer' doc= 'RTP jitter buffer' />
<param name= '<0-10000>' doc= 'jitter buffer in ms' />
<param name= '[adaptive]' doc= '(null)' />
</params>
</command>
<command id= 'rtp port-range <1-65534> <1-65534>' >
<params >
<param name= 'rtp' doc= 'RTP parameters' />
<param name= 'port-range' doc= 'Range of local ports to use for RTP/RTCP traffic' />
<param name= '<1-65534>' doc= '(null)' />
<param name= '<1-65534>' doc= '(null)' />
</params>
2020-05-29 11:49:03 +00:00
</command>
<command id= 'rtp ip-dscp <0-63>' >
<params >
<param name= 'rtp' doc= 'RTP parameters' />
<param name= 'ip-dscp' doc= 'Specify DSCP for RTP/IP packets' />
<param name= '<0-63>' doc= 'The DSCP value (upper 6 bits of TOS)' />
</params>
2019-06-19 10:18:24 +00:00
</command>
<command id= 'band (450|GSM450|480|GSM480|750|GSM750|810|GSM810|850|GSM850|900|GSM900|1800|DCS1800|1900|PCS1900)' >
<params >
<param name= 'band' doc= 'Set the frequency band of this BTS' />
<param name= '450' doc= 'Alias for GSM450' />
<param name= 'GSM450' doc= '450Mhz' />
<param name= '480' doc= 'Alias for GSM480' />
<param name= 'GSM480' doc= '480Mhz' />
<param name= '750' doc= 'Alias for GSM750' />
<param name= 'GSM750' doc= '750Mhz' />
<param name= '810' doc= 'Alias for GSM810' />
<param name= 'GSM810' doc= '810Mhz' />
<param name= '850' doc= 'Alias for GSM850' />
<param name= 'GSM850' doc= '850Mhz' />
<param name= '900' doc= 'Alias for GSM900' />
<param name= 'GSM900' doc= '900Mhz' />
<param name= '1800' doc= 'Alias for DCS1800' />
<param name= 'DCS1800' doc= '1800Mhz' />
<param name= '1900' doc= 'Alias for PCS1900' />
<param name= 'PCS1900' doc= '1900Mhz' />
</params>
</command>
<command id= 'description .TEXT' >
<params >
<param name= 'description' doc= 'Save human-readable description of the object' />
<param name= '.TEXT' doc= 'Text until the end of the line' />
</params>
</command>
<command id= 'no description' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'description' doc= 'Remove description of the object' />
</params>
</command>
<command id= 'paging queue-size <1-1024>' >
<params >
<param name= 'paging' doc= 'Paging related parameters' />
<param name= 'queue-size' doc= 'Maximum length of BTS-internal paging queue' />
<param name= '<1-1024>' doc= 'Maximum length of BTS-internal paging queue' />
</params>
</command>
<command id= 'paging lifetime <0-60>' >
<params >
<param name= 'paging' doc= 'Paging related parameters' />
<param name= 'lifetime' doc= 'Maximum lifetime of a paging record' />
<param name= '<0-60>' doc= 'Maximum lifetime of a paging record (secods)' />
</params>
</command>
<command id= 'agch-queue-mgmt default' >
<params >
<param name= 'agch-queue-mgmt' doc= 'AGCH queue mgmt' />
<param name= 'default' doc= 'Reset clean parameters to default values' />
</params>
</command>
<command id= 'agch-queue-mgmt threshold <0-100> low <0-100> high <0-100000>' >
<params >
<param name= 'agch-queue-mgmt' doc= 'AGCH queue mgmt' />
<param name= 'threshold' doc= 'Threshold to start cleanup' />
<param name= '<0-100>' doc= 'in %% of the maximum queue length' />
<param name= 'low' doc= 'Low water mark for cleanup' />
<param name= '<0-100>' doc= 'in %% of the maximum queue length' />
<param name= 'high' doc= 'High water mark for cleanup' />
<param name= '<0-100000>' doc= 'in %% of the maximum queue length' />
</params>
</command>
<command id= 'uplink-power-target <-110-0>' >
<params >
<param name= 'uplink-power-target' doc= 'Set the nominal target Rx Level for uplink power control loop' />
<param name= '<-110-0>' doc= 'Target uplink Rx level in dBm' />
</params>
</command>
<command id= 'min-qual-rach <-100-100>' >
<params >
<param name= 'min-qual-rach' doc= 'Set the minimum link quality level of Access Bursts to be accepted' />
<param name= '<-100-100>' doc= 'C/I (Carrier-to-Interference) ratio in centiBels (10e-2 B or 10e-1 dB)' />
</params>
</command>
<command id= 'min-qual-norm <-100-100>' >
<params >
<param name= 'min-qual-norm' doc= 'Set the minimum link quality level of Normal Bursts to be accepted' />
<param name= '<-100-100>' doc= 'C/I (Carrier-to-Interference) ratio in centiBels (10e-2 B or 10e-1 dB)' />
</params>
</command>
<command id= 'max-ber10k-rach <0-10000>' >
<params >
<param name= 'max-ber10k-rach' doc= 'Set the maximum BER for valid RACH requests' />
<param name= '<0-10000>' doc= 'BER in 1/10000 units (0=no BER; 100=1% BER)' />
</params>
</command>
<command id= 'pcu-socket PATH' >
<params >
<param name= 'pcu-socket' doc= 'Configure the PCU socket file/path name' />
<param name= 'PATH' doc= '(null)' />
</params>
</command>
<command id= 'supp-meas-info toa256' >
<params >
<param name= 'supp-meas-info' doc= 'Configure the RSL Supplementary Measurement Info' />
<param name= 'toa256' doc= 'Report the TOA in 1/256th symbol periods' />
</params>
</command>
<command id= 'no supp-meas-info toa256' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'supp-meas-info' doc= 'Configure the RSL Supplementary Measurement Info' />
<param name= 'toa256' doc= 'Report the TOA in 1/256th symbol periods' />
</params>
</command>
<command id= 'smscb queue-max-length <1-60>' >
<params >
<param name= 'smscb' doc= 'Maximum queue length for SMSCB (CBCH) queue. In count of messages/pages (Default: 15)' />
<param name= 'queue-max-length' doc= '(null)' />
<param name= '<1-60>' doc= '(null)' />
</params>
</command>
<command id= 'smscb queue-target-length <1-30>' >
<params >
<param name= 'smscb' doc= 'Target queue length for SMSCB (CBCH) queue. In count of messages/pages (Default: 2)' />
<param name= 'queue-target-length' doc= '(null)' />
<param name= '<1-30>' doc= '(null)' />
</params>
</command>
<command id= 'smscb queue-hysteresis <0-30>' >
<params >
<param name= 'smscb' doc= 'Hysteresis for SMSCB (CBCH) queue. In count of messages/pages (Default: 2)' />
<param name= 'queue-hysteresis' doc= '(null)' />
<param name= '<0-30>' doc= '(null)' />
</params>
</command>
<command id= 'gsmtap-sapi (bcch|ccch|rach|agch|pch|sdcch|tch/f|tch/h|pacch|pdtch|ptcch|cbch|sacch)' >
<params >
<param name= 'gsmtap-sapi' doc= 'GSMTAP SAPI' />
<param name= 'bcch' doc= 'BCCH' />
<param name= 'ccch' doc= 'CCCH' />
<param name= 'rach' doc= 'RACH' />
<param name= 'agch' doc= 'AGCH' />
<param name= 'pch' doc= 'PCH' />
<param name= 'sdcch' doc= 'SDCCH' />
<param name= 'tch/f' doc= 'TCH/F' />
<param name= 'tch/h' doc= 'TCH/H' />
<param name= 'pacch' doc= 'PACCH' />
<param name= 'pdtch' doc= 'PDTCH' />
<param name= 'ptcch' doc= 'PTCCH' />
<param name= 'cbch' doc= 'CBCH' />
<param name= 'sacch' doc= 'SACCH' />
</params>
</command>
<command id= 'no gsmtap-sapi (bcch|ccch|rach|agch|pch|sdcch|tch/f|tch/h|pacch|pdtch|ptcch|cbch|sacch)' >
<params >
<param name= 'no' doc= 'Negate a command or set its defaults' />
<param name= 'gsmtap-sapi' doc= 'GSMTAP SAPI' />
<param name= 'bcch' doc= 'BCCH' />
<param name= 'ccch' doc= 'CCCH' />
<param name= 'rach' doc= 'RACH' />
<param name= 'agch' doc= 'AGCH' />
<param name= 'pch' doc= 'PCH' />
<param name= 'sdcch' doc= 'SDCCH' />
<param name= 'tch/f' doc= 'TCH/F' />
<param name= 'tch/h' doc= 'TCH/H' />
<param name= 'pacch' doc= 'PACCH' />
<param name= 'pdtch' doc= 'PDTCH' />
<param name= 'ptcch' doc= 'PTCCH' />
<param name= 'cbch' doc= 'CBCH' />
<param name= 'sacch' doc= 'SACCH' />
</params>
</command>
<command id= 'trx <0-254>' >
<params >
<param name= 'trx' doc= 'Select a TRX to configure' />
<param name= '<0-254>' doc= 'TRX number' />
</params>
</command>
</node>
<node id= 'trx' >
<name > trx</name>
<command id= 'user-gain <-100000-100000> (dB|mdB)' >
<params >
<param name= 'user-gain' doc= 'Inform BTS about additional, user-provided gain or attenuation at TRX output' />
<param name= '<-100000-100000>' doc= 'Value of user-provided external gain(+)/attenuation(-)' />
<param name= 'dB' doc= 'Unit is dB (decibels)' />
<param name= 'mdB' doc= 'Unit is mdB (milli-decibels, or rather 1/10000 bel)' />
</params>
</command>
<command id= 'power-ramp max-initial <0-100000> (dBm|mdBm)' >
<params >
<param name= 'power-ramp' doc= 'Power-Ramp settingsMaximum initial power' />
<param name= 'max-initial' doc= 'Value' />
<param name= '<0-100000>' doc= 'Unit is dB (decibels)' />
<param name= 'dBm' doc= 'Unit is mdB (milli-decibels, or rather 1/10000 bel)' />
<param name= 'mdBm' doc= '(null)' />
</params>
</command>
<command id= 'power-ramp step-size <1-100000> (dB|mdB)' >
<params >
<param name= 'power-ramp' doc= 'Power-Ramp settingsPower increase by step' />
<param name= 'step-size' doc= 'Step size' />
<param name= '<1-100000>' doc= 'Unit is dB (decibels)' />
<param name= 'dB' doc= 'Unit is mdB (milli-decibels, or rather 1/10000 bel)' />
<param name= 'mdB' doc= '(null)' />
</params>
</command>
<command id= 'power-ramp step-interval <1-100>' >
<params >
<param name= 'power-ramp' doc= 'Power-Ramp settingsPower increase by step' />
<param name= 'step-interval' doc= 'Step time in seconds' />
<param name= '<1-100>' doc= '(null)' />
</params>
</command>
<command id= 'ms-power-control (dsp|osmo)' >
<params >
<param name= 'ms-power-control' doc= 'Mobile Station Power Level Control (change requires restart)' />
<param name= 'dsp' doc= 'Handled by DSP' />
<param name= 'osmo' doc= 'Handled by OsmoBTS' />
</params>
</command>
<command id= 'phy <0-255> instance <0-255>' >
<params >
<param name= 'phy' doc= 'Configure PHY Link+Instance for this TRX' />
<param name= '<0-255>' doc= 'PHY Link number' />
<param name= 'instance' doc= 'PHY instance' />
<param name= '<0-255>' doc= 'PHY Instance number' />
</params>
</command>
</node>
</vtydoc>