This fixes a bug in the following circumstances:
* BSIC is set to 0 in the config file
* No TSC is explicitly specified at the BST level in the config file
In this case, we ended up using BSIC=0 and TSC=7, as TSC=7 is our
default initialization value.
The TSC of the CCCH/BCCH must always be the BCC, which is the lower 3
bits of the BSIC. Having configuration options for both the BSIC _and_
the TSC at the BTS level therefore makes no sense, as it only adds ways
in which users can configure non-oprational configurations. So we
remove the bts->tsc member, and keep only the ts->tsc members that allow
us to configure a timeslot-specific TSC that's different from the BTS
TSC (= BCC).
The signature of mr_config and the BSC implementation didn't
match and the compiler was warning about it:
osmo_bsc_api.c:530:2: warning: initialization from incompatible pointer type
.mr_config = bsc_mr_config,
^
osmo_bsc_api.c:530:2: warning: (near initialization for ‘bsc_handler.mr_config’)
Change the mr_config again and provide an implementation
that will set the ms and bts data structure. It would be
better to put the size outside of the IE but I am not going
to change it right now. It would also be nice to either move
the AMR setting into the "nitb" structure or have the msc
data be used _after_ the bts settings. This needs to be
cleaned up in the next step.
Manually verified by placing a MO call and checking that
both the channel mode modify and the mode modify request
contain the multi rate config with the rate mr config
(length two bytes, version 1, icmi==1, no start mode being
set).
This way a lot of if/else can just be killed by the caller deciding
which of the two instances to use.
I have copied both branches to new files, replace bts for ms in one
of them and ran diff on it. There is no difference.
Merge two copies into a local static helper function. The format
of the message will change and then it is easier to modify it in
one place than in two.
Sadly the original patch was merged before this clean-up so do
the clean-up as second step.
Conflicts:
openbsc/src/libbsc/abis_rsl.c
openbsc/src/libbsc/gsm_04_08_utils.c
As the comment says we should not rely that the paging
occurs on the current LAC. We might page at more BTS.
Walk all the BTS to stop paging. No callbacks will be
issued by this stop operation.
In case we can't page on a BTS then stop it everywhere. The
callers of paging_request assume that this is kind of an
atomic operation and we should help with that.
Check if the NAT has sent 16 bytes of RAND and if a key
has been configured in the system and then generate a
result using milenage. The milenage res will be sent and
noth the four byte GSM SRES derivation.
Unfortunately the basic structure of the response is broken.
There is a two byte length followed by data. The concept of
a 'tag' happens to be the first byte of the data.
This means we want to write strlen of the token, then we
want to write the NUL and then we need to account for the
tag in front.
Introduce a flag if the new or old format should be used.
This will allow to have new BSCs talk to old NATs without
an additional change. In the long run we can clean that up.
The code to do that doesn't belong to the control interface, so
abstract it out to a separate function gsm_bts_set_system_infos().
[hfreyther: Fix the coding style...]
We had issues with odd behavior on the nanoBTS which lead
to the introduction of the "broken" state. On busy multi
BTS cells (e.g. rhizomatica) with wifi backhaul the timeout
we set to wait for a RF Channe Release ACK is sometimes too
little and channels are marked broken that look to be okay
(besides the still to be determined delay).
In case of a sysmoBTS we now know that we can change the
state of a broken channel back to normal in case we do
receive the right response.
Manually verified using the Smalltalk BTS code
PackageLoader fileInPackage: 'FakeBTS'
bts := FakeBTS.BTS new.
bts btsId: '1903/0/0'.
bts connect: 'localhost'.
bts waitForBTSReady.
test := FakeBTS.OpenBSCTest new.
test bts: bts.
test requireAnyChannel
... wait for NITB output
<0004> abis_rsl.c:223 (bts=0,trx=0,ts=0,ss=0) Timeout during deactivation! Marked as broken.
... process pending messages
stdin next
<0004> abis_rsl.c:735 (bts=0,trx=0,ts=0,ss=0) CHAN REL ACK for broken channel. Releasing it.
So the channel went from broken to unallocated.
Create a control command to read and modify the gprs mode. Use
the get_string_value to indicate if the value was found or not.
This is useful for the ctrl interface where I didn't want to
replicate "none", "gprs" and "egprs". Share code to verify that
a BTS supports the mode.
Related: SYS#591
30f1f37638 introduced new channel
combinations but had a copy and paste error in the description.
The jenkins system didn't run the external tests so this issue
and others were not noticed until now.
Fix the copy and paste and update the test result.
This is a normal situation under high load: The BTS is out of resources
and the BSC cannot allocate any dedicated channel. We may send an IMM
ASS REJECT back to the MS. All well within normal parameters, not an
error that needs to be reported back to the caller, who propagates it
all the way up to libosmo-abis.
Move the "logging filter imsi IMSI" into the BTS/NITB code to
allow to set the gsm_subscriber and only compare it. This way
we simply compare the subscriber address and don't have to care
if the subscriber data is still valid.
The idea of ts_alloc()/ts_free() dates back to the very early days of
OpenBSC, where we didn't yet have a fixed PCHAN type assigned for every
lchan in a BTS. However, ever since, PCHAN types (channel combinations)
are configured by OML in a certain way, and we only allocate LCHANs
inside PCHANs of a matching type. There should be no PCHANs with
type GSM_PCHAN_NONE, unless those that you don't want to use for
administraive reasons or the like.
==25637==ERROR: AddressSanitizer: stack-buffer-overflow on address 0x7fff3f587c43 at pc 0x5bf591 bp 0x7fff3f587630 sp 0x7fff3f587628
READ of size 4 at 0x7fff3f587c43 thread T0
#0 0x5bf590 in tv_fixed_put /home/alphaone/local/osmo-asan/include/osmocom/gsm/tlv.h:237
#1 0x5b7e14 in generate_si4 /home/alphaone/scm/osmo/openbsc/openbsc/src/libbsc/system_information.c:607
#2 0x5b488b in gsm_generate_si /home/alphaone/scm/osmo/openbsc/openbsc/src/libbsc/system_information.c:882
#3 0x4cb247 in gsm_bts_trx_set_system_infos /home/alphaone/scm/osmo/openbsc/openbsc/src/libbsc/bsc_init.c:166
#4 0x4d3c26 in bootstrap_rsl /home/alphaone/scm/osmo/openbsc/openbsc/src/libbsc/bsc_init.c:272
#5 0x4ced44 in inp_sig_cb /home/alphaone/scm/osmo/openbsc/openbsc/src/libbsc/bsc_init.c:316
#6 0x7f4f15b563d7 in osmo_signal_dispatch /home/alphaone/scm/osmo/libosmocore/src/signal.c:105
#7 0x7f4f156c0e3f in e1inp_int_snd_event (/home/alphaone/local/osmo-asan/lib/libosmoabis.so.4+0x17e3f)
#8 0x7f4f156be7e5 in e1inp_event (/home/alphaone/local/osmo-asan/lib/libosmoabis.so.4+0x157e5)
#9 0x583a6a in ipaccess_sign_link /home/alphaone/scm/osmo/openbsc/openbsc/src/libbsc/bts_ipaccess_nanobts.c:675
#10 0x7f4f156e63b0 in handle_ts1_read (/home/alphaone/local/osmo-asan/lib/libosmoabis.so.4+0x3d3b0)
#11 0x7f4f156e4f4e in ipaccess_fd_cb (/home/alphaone/local/osmo-asan/lib/libosmoabis.so.4+0x3bf4e)
#12 0x7f4f15b540b6 in osmo_select_main /home/alphaone/scm/osmo/libosmocore/src/select.c:160
#13 0x43c656 in main /home/alphaone/scm/osmo/openbsc/openbsc/src/osmo-nitb/bsc_hack.c:355
#14 0x7f4f1462e4bc (/lib64/libc.so.6+0x224bc)
#15 0x43b6cc (/home/alphaone/local/osmo-asan/bin/osmo-nitb+0x43b6cc)
Address 0x7fff3f587c43 is located in stack of thread T0 at offset 483 in frame
#0 0x5b712f in generate_si4 /home/alphaone/scm/osmo/openbsc/openbsc/src/libbsc/system_information.c:580
This frame has 8 object(s):
[32, 40) ''
[96, 104) ''
[160, 164) 'rc'
[224, 232) 'si4'
[288, 296) 'cbch_lchan'
[352, 360) 'restoct'
[416, 420) 'l2_plen'
[480, 483) 'cd'
HINT: this may be a false positive if your program uses some custom stack unwind mechanism or swapcontext
(longjmp and C++ exceptions *are* supported)
SUMMARY: AddressSanitizer: stack-buffer-overflow /home/alphaone/local/osmo-asan/include/osmocom/gsm/tlv.h:237 tv_fixed_put
We can now configure the pyisical channel types for CBCH either in the
CCCH+SDCCH4 or in the SDCCH8 chanel combination.
Depending on whether a CBCH exists on the BTS, we also generate the SI4
with matching CBCH channel description to notify the phones of the
existance of the CBCH.
There is now a VTY command how a SMS-CB message can be sent to a given
BTS.
We do not yet have any logic at all for actual scheduling of multiple
CBCH RSL messages towards one or multiple BTSs yet, though.
The new lchan will be in speech mode already but for AMR we will
need to provide a working multirate config in the channel activation,
otherwise the channel act might be nacked.
Copy the config from the current lchan into the new lchan. The
abis code simply added the mrconf if the speech mode was amr.
Before this commit the invalidate mrconf with all zeroes was
copied/sent.
In case of a ho_chan_activ_nack (sent due another bug inside
both sysmobts and openbsc) the code would not stop the timer
but free the datastructure. This can lead to a clear segfault
when the timer has expired. Create a "free" function which is
responsible to detach the handover structure, stop the timer
(which is idempotent) and free the structure.
In case a BTS is dropped, iterate over the list of BTS and check
if a dependency is now missing and then drop the BTS. This check
could lead to check of 256*256 checks (e.g. all BTS on each other
in the chain and the master is being dropped). The performance
aspect of it doesn't matter for our usecase. We expect to have
pairs of BTS right now.
E.g. for the sysmoBTS2050 we have the requirement that the first
board connects before the second due clocking. The easiest point
to enforce this is the BSC. Add a simple bitmask based system to
allow to express dependencies for IP based systems.
Currently every subcriber object directly refers to the gsm_network
which contains a flag shared by every related subscriber
(keep_subscr). This adds a dependency on gsm_network even if only the
function defined in gsm_subscriber_base.c are used.
This patch adds a new struct gsm_subscriber_group which contains the
keep_subscr flag and a back reference to the network object. The
latter is not dereferenced in gsm_subscriber_base.c, so it can safely
be set to NULL when only that part of the gsm_subscriber API is being
used. It also changes that API to use gsm_subscriber_group instead of
gsm_network parameters.
Since there are some places where a pointer to the gsm_network is
needed but where only a gsm_subscriber is available, a 'net' back
pointer is added to the group struct, too. Nevertheless subscr group
and network could be separated completely, but this is not the topic
of this commit.
Sponsored-by: On-Waves ehf
Harald Welte
Jacob Erlbeck