When OM2000 has confirmed that a TS is started, call dyn_ts_init()
on the timeslot to start the processing for fully dynamic (osmocom
style) TCH/F_TCH/H_PDCH. This should in turn trigger the activation of
idle timeslots as PDCH until we want to allocate any of them for TCH/F
or TCH/H.
Change-Id: I1a1fd61d6afd85449cacad4bacfb830252dab6b1
The code for supporting the configuration of the OM2000 CON (LAPD
Concentrator) MO was so far incomplete and not used from the OM2000 FSM
initialization. This patch adds
* VTY commands for configuration of CON Groups and Paths
* The FSM integration to actually configure the CON MO
Change-Id: I56dc1b5e35adef3a2078bcf9536537eb0f454192
For TCH/F_PDCH, return an invalid chan comb (0) and print an error message
that hints at the proper pchan type to use instead: TCH/F_TCH/H_PDCH
Change-Id: Ibe0f944573f0a6d1be4bf7cf4986c4b2b3bd6d0d
When OM2K sets up the timeslots with the BTS, the dynamic channel state
is not yet resolved to any particular pchan type. Instead of using the
dyn state, always advertise dynamic timeslots as pchan2comb(TCH/F).
In the past, the Ericsson dynamic timeslots were handled as pchan type
TCH/F_PDCH. This is a mistake, as this pchan type is intended for
the ip.access dynamic PDCH way of dynamic channels. In any case, in the
initial state of this pchan type, the timeslot was initialized as
pchan2comb(TCH/F) because the ts->flags do not reflect an active PDCH
yet. In short, this patch does not change the behavior of TCH/F_PDCH
timeslots, only clarifies it.
It would in fact make sense to disallow use of TCH/F_PDCH for OM2K,
but that should probably be a separate patch.
The proper pchan to use for Ericsson dynamic timeslots is
TCH/F_TCH/H_PDCH. These do not use ts->flags, but ts->dyn.* as state,
which first reflects pchan_want == pchan_is == GSM_PCHAN_NONE. Hence
the timeslot was initialized by OM2K as pchan type zero, which is
unknown / invalid. So, instead of using pchan_is, which is not yet
reflecting anything meaningful, always initialize as TCH/F chan comb,
as Ericsson hardware apparently expects it.
Change-Id: If0693f7c5c85977b0e4acbc701ee5d635434d0d1
Throw warning message in case the MO state does not change
to enabled after sendeing an Enable-Request message.
Change-Id: Idfde8d6f71526e8acfea51835732515a4bee858e
This patch adds parsing for OM2000 MO fault report map parsing,
the bits in the fault maps are counted out and displayed.
Change-Id: I6e2928f39b09bc08e9ab78bc10bc81e07f7eb55d
When receiving the 'Start Result' message, for CF and TRXC MO
we directly transition to performing the Operational Info. In that
case, we need to return after sending the Operational Info and skip
the usual processing for the default case below.
Change-Id: I99860d198b337ffe461b240bda20dc10e1b5b2cb
Our existing OM2000 code for initializing all Managed Objects of a BTS
at startup was never complete. Rather than trying to fix the old-style
code, introudce a hierarchy of osmo_fsm's reflecting the full protocol
hand-shake and sequence of bringing up the individual MO's.
If this works out well, it mihgt make sense to convert the TS 12.21 OML
code for other BTS models, too.
Change-Id: I3e11b28ba22b8c227e0401e6207fdda5381dda8c
Add ts2comb() to switch on dyn TS so that dyn TS in TCH mode are also treated
like normal TCH/H or TCH/F pchans. Use ts2comb() instead of pchan2comb().
Change-Id: Iddc51a4409488d91db59228ca66aaab73ce3f1df
The libosmo-abis merge broke Ericsson RBS support, as it didn't get the
part right where the per-TRX OML sign_link is determined while
transmitting OM2000 messages.
As a result of this fix, we can remove the 'to_trx_oml' parameter to
_abis_nm_sendmsg(), which is a nice cleanup.
This is a big patch that ports openBSC over libosmo-abis.
Sorry, the changes that are included here are all dependent
of libosmo-abis, splitting them into smaller pieces would
leave the repository in some intermediate state, which is
not desired.
The main changes are:
- The directory libabis/ has been removed as it now lives in
libosmo-abis.
- new configuration file format for nanoBTS and HSL femto, we
need to define the virtual e1_line and attach it to the OML
link.
- all the existing BTS drivers (nanoBTS, hsl femto, Nokia site,
BS11 and rbs2000) now use the new libosmo-abis framework.
- use r232 input driver available in libosmo-abis for bs11_config.
- use ipa_msg_recv instead of old ipaccess_read_msg function.
- delete definition of gsm_e1_subslot and input_signal_data.
These structures now lives in libosmo-abis.
Most of this patch are deletions of libabis/ which has been
moved to libosmo-abis.
This patch also modifies openBSC to use all the new definitions
available in libosmocore and libosmo-abis. In order to do that,
we have replaced the following:
- DINP, DMI, DMIB and DMUX by their respective DL* correspondences.
- SS_GLOBAL by SS_L_GLOBAL
- SS_INPUT by SS_L_INPUT
- S_GLOBAL_SHUTDOWN by S_L_GLOBAL_SHUTDOWN
- SS_INPUT by SS_L_INPUT
- S_INP_* by S_L_INP_* sub-signals
- E1INP_NODE by L_E1INP_NODE vty node
This patch has been tested with:
- one nanoBTS
- the HSL femto with the examples available under libosmo-abis
- BS11 with both dahdi and misdn drivers.
This patch modifies openBSC code to use msg->dst which stores the
pointer to the signalling link structure instead of the pointer to
the transceiver structure.
This patch prepares the introduction of libosmo-abis.
libosmogsm is a new library that is distributed in the libosmocore.
Now, openbsc depends on it. This patch gets openbsc with this
change.
This patch also rewrites all include path to the new
osmocom/[gsm|core]
Signed-off-by: Pablo Neira Ayuso <pablo@gnumonks.org>
... and in order to do this reasonably well, we have to get rid of
the pre-computed message length field in the OML header. Instead,
we now simply compute it at abis_om2k_sendmsg() time based on the
msgb_l2len().
Harald Welte
Philipp Maier
Neels Hofmeyr
root