While NACC was initially developed, it became clear there was need for
a way to interact PCU<->BSC in order resolve ARFCN+BSIC into CGI-PS
for later RIM usage.
Hence, this resolution was first (until today) implemented using an out
of bands RPC system using the CTRL interface, which required specific
config to be written and matches in osmo-pcu and osmo-bsc VTY (ip+port
of the CTRL interface to use).
However, this has several shortcomings:
* As explained above, specific configuration is required
* Since recently, we do support BSC redundancy in osmo-bts. Hence the BTS
may switch to a BSC other than first one. If that happened, that'd mean
the CTRL interface would still point to the initially configured one,
which may not be the same currently serving the PCU.
During recent development of ANR related features, a similar need for
PCU<->BSC was required, but this time it was decided to extend the IPA
multiplex of the Abis OML connection to pass PCUIF messages,
transparently forwarded to each side by the BTS.
This has the advantage that connection PCU<->BTS is handled by BTS and
both sides send messages transparently.
Let's switch by default to using this new interface, while still
maintaing the old way for a while (announcing them as deprecated) to
avoid breaking existing deployments until they are upgraded to new
versions of osmo-pcu and osmo-bsc.
Change-Id: I9073a121564503f483c84263ac72476041e47c03
Related: SYS#4971
For balancing load across congested cells and across congested TCH/*
kinds, instead of comparing the number of lchans above the configured
congestion threshold, compare the percent of lchans of overload.
In short, using a percentage prevents cells with less min-free-slots to
fill up 100% while neighbor cells still may have several free lchans
available.
An obvious example of why this is desirable is illustrated by
test_balance_congestion_by_percentage.ho_vty:
Cell A has min-free-slots 2, and has all slots occupied.
Cell B has min-free-slots 4, and has 2 slots remaining free.
If we count congested lchans as in current master: cell A has a
congestion count of 2: two more lchans in use than "allowed". If we move
one lchan over to cell B, it ends up with a congestion count of 3, which
is worse than 2. So when counting lchans, we decide that cell A should
remain full.
Instead, when comparing percentage of remaining lchans, we would see
that cell A is loaded 100% above congestion (2 of 2 remaining lchans in
use), but when moving one lchan to cell B, that would only be 75% loaded
above its treshold (3 of 4 remaining lchans in use). So a percentage
comparison would cause a handover to cell B.
Related: SYS#5259
Change-Id: I55234c6c99eb02ceee52be0d7388bea14304930f
This new CTRL interface allows users of this BSC (such as attached PCU)
to gather neighbor information.
This interface is needed for PCU to translate ARFCN+BSIC keys provided
by MS in the Um side into CGI + RAC keys used to identify target cells
in RIM procedures against SGSNs on the Gb interface.
This patch extends the already existing neighbor information storage in
the VTY by allowing storage of CGI + RAC (RAC couldn't be stored
beforehand).
Related: SYS#4909
Depends: libosmocore.git Change-Id If48f412c32e8e5a3e604a78d12b74787a4786374
Change-Id: Ib07c9d23026332a207d4b7a0f7b4e76c0094e379
This adds some instructions on how to configure 3G/4G neighbor
cells within osmo-bsc. I didn't want to add a new top-level
chapter but instead chose to add it to the handover section which
describes also the configuration of 2G neighbors.
Change-Id: I81df1a453858b6fca80c8adf234b1d5b8bf5283d
Add chapter "Handover", explaining:
- intra- and
- inter-BSC handover,
- HO algorithm 1 and
- algorithm 2
- new neighbor configuration
Adjust copyright, add revision and add me as author.
Change-Id: I7afb3f66c98abda07fc8acc76e00c46091fe55e2
Pau Espin
Neels Hofmeyr
Martin Hauke
Harald Welte