mirror of https://gerrit.osmocom.org/osmo-tetra
Update README to reflect project status
This commit is contained in:
parent
7b423e9989
commit
6c73dad43d
86
README
86
README
|
@ -1,9 +1,9 @@
|
|||
TETRA MAC/PHY layer experimentation code
|
||||
(C) 2010 by Harald Welte <laforge@gnumonks.org>
|
||||
(C) 2010-2011 by Harald Welte <laforge@gnumonks.org>
|
||||
======================================================================
|
||||
|
||||
This code aims to implement the (so far) sending and (in the future)
|
||||
receiving part of the TETRA MAC/PHY layer.
|
||||
This code aims to implement the sending and receiving part of the
|
||||
TETRA MAC/PHY layer.
|
||||
|
||||
If you read the ETSI EN 300 392-2 (TETRA V+D Air Interface), you will
|
||||
find this code implementing the parts between the MAC-blocks (called
|
||||
|
@ -12,23 +12,58 @@ type-1 bits) and the bits that go to the DQPSK-modulator (type-5 bits).
|
|||
It is most useful to look at Figure 8.5, 8.6, 9.3 and 19.12 in conjunction
|
||||
with this program.
|
||||
|
||||
You will need libosmocore (http://bb.osmocom.org/trac/wiki/libosmocore) to link.
|
||||
|
||||
|
||||
== Demodulator ==
|
||||
|
||||
src/demod/python/cpsk.py
|
||||
* contains a gnuradio based pi4/DQPSK demodulator, courtesy of KA1RBI
|
||||
src/demod/python/tetra-demod.py
|
||||
* call demodulator on a 'cfile' containing complex baseband samples
|
||||
src/demod/python/usrp1-tetra_demod.py
|
||||
* use demodulator in realtime with a USRP1 SDR
|
||||
src/demod/python/usrp2-tetra_demod.py
|
||||
* use demodulator in realtime with a USRP2 SDR
|
||||
|
||||
The output of the demodulator is a file containing one float value for each symbol,
|
||||
containing the phase shift (in units of pi/4) relative to the previous symbol.
|
||||
|
||||
You can use the "float_to_bits" program to convert the float values to unpacked
|
||||
bits, i.e. 1-bit-per-byte
|
||||
|
||||
|
||||
== PHY/MAC layer ==
|
||||
|
||||
=== library code ===
|
||||
|
||||
Specifically, it implements:
|
||||
lib_crc.[ch]
|
||||
* CRC16-CCITT (currently defunct/broken as we need it for
|
||||
non-octet-aligned bitfields)
|
||||
tetra_rm3014.[ch]
|
||||
* (30, 14) Reed-Muller code for the ACCH (broadcast block of
|
||||
each downlink burst)
|
||||
tetra_conv_enc.[ch]
|
||||
* 16-state Rate-Compatible Punctured Convolutional (RCPC) coder
|
||||
tetra_interleave.[ch]
|
||||
* Block interleaving (over a single block only)
|
||||
tetra_scramb.[ch]
|
||||
* Scrambling
|
||||
tetra_burst.[ch]
|
||||
* Routines to encode continuous normal and sync bursts
|
||||
testpdu.[ch]
|
||||
* Routines to build some example SYNC-PDU and SYSINFO-PDU
|
||||
lower_mac/crc_simple.[ch]
|
||||
* CRC16-CCITT (currently defunct/broken as we need it for
|
||||
non-octet-aligned bitfields)
|
||||
lower_mac/tetra_conv_enc.[ch]
|
||||
* 16-state Rate-Compatible Punctured Convolutional (RCPC) coder
|
||||
lower_mac/tetra_interleave.[ch]
|
||||
* Block interleaving (over a single block only)
|
||||
lower_mac/tetra_rm3014.[ch]
|
||||
* (30, 14) Reed-Muller code for the ACCH (broadcast block of
|
||||
each downlink burst)
|
||||
lower_mac/tetra_scramb.[ch]
|
||||
* Scrambling
|
||||
lower_mac/viterbi*.[ch]
|
||||
* Convolutional decoder for signalling and voice channels
|
||||
phy/tetra_burst.[ch]
|
||||
* Routines to encode continuous normal and sync bursts
|
||||
phy/tetra_burst_sync.[ch]
|
||||
|
||||
|
||||
=== Receiver Program ===
|
||||
|
||||
The main receiver program 'tetra-rx' expects an input file containing a
|
||||
stream of unpacked bits, i.e. 1-bit-per-byte.
|
||||
|
||||
|
||||
=== Transmitter Program ===
|
||||
|
||||
The main program conv_enc_test.c generates a single continuous downlinc sync
|
||||
burst (SB), contining:
|
||||
|
@ -38,13 +73,14 @@ burst (SB), contining:
|
|||
|
||||
Scrambling is set to 0 (no scrambling) for all elements of the burst.
|
||||
|
||||
You will need libosmocore (http://bb.osmocom.org/trac/wiki/libosmocore) to link.
|
||||
It does not actually modulate and/or transmit yet.
|
||||
|
||||
|
||||
== Quick example ==
|
||||
|
||||
USAGE:
|
||||
|
||||
src/float_to_bits data/dqpsk-float.dat data/out.bits
|
||||
|
||||
src/burst_test data/out.bits
|
||||
# assuming you have generated a file samples.cfile at a sample rate of
|
||||
# 195.312kHz (100MHz/512 == USRP2 at decimation 512)
|
||||
src/demod/python/tetra-demod.py -i /tmp/samples.cfile -o /tmp/out.float -s 195312 -c 0
|
||||
src/float_to_bits /tmp/out.float /tmp/out.bits
|
||||
src/tetra-rx /tmp/out.bits
|
||||
|
||||
|
|
Loading…
Reference in New Issue