This adds support for the new ngff_cardem board, a board that
basically combines a ngff breakout board with a built-in SIMtrace2.
Cardem works, but depending on the modem it might need a adjusted ATR to
ensure a lower baud rate is used by the modem, high rates might lead
to weird power cycling of the card after a few transfers.
Trace was also tested and appears to work as expected.
Change-Id: Ia96124fbe8a752c98e7fd4096d542a3b2b9bc255
likewise, enable HAVE_SNIFFER currently only if we build the sniffer
firmware.
It's been many years too long to finally get those all merged in one
firmware :(
Change-Id: Ib433f180746f75458a44f4988643465bd846b04b
While this differs from tha naming in the schematics ({CLK,IO}_PHONE),
this matches the naming scheme used for USIM2 and the naming on other
boards.
Change-Id: I486b14260faec897e8c8698c4b7987bf36492497
monitoring the state changes of the VCC and nRST lines is required
to correctly detect warm and cold reset
Change-Id: I72099956332724f84226e1495fdc5a5b1a034695
the LEDs (2 of them) were connected to the same pins on all
boards, up to the octsim-tester.
to be able to have board specific LEDs the definitions have moved
from common to the each board.
at the same time I added a bit of documentation what the LEDs are
used for.
Change-Id: I3226a9187a8d0b657ccf5dcd8f3586b2578f96d2
SIM_PWEN and VCC_FWD are signals specific to the simtrace boards.
the corresponding pins PA5 and PA26 are used for other signal
on the octsim-tester.
Change-Id: I51f37dd112cf681f4b1dbb3d2320ff9a697eaa08
UART baud rate is main clock (MCK) divided by CR*16.
The MCK values are chosen >= 48 MHz and <= 64 MHz to have a near
integer value CR for a baud rate of 921600 bps.
The end MCK frequency between simtrace and qmod differ slightly
but are close to 58 MHz.
Change-Id: Iaa4a97fc68494c93b9d128503515d88049de506c
USB reset can be signaled by pulling low USB D+ for at least 10 ms,
according to the USB specification. This force a re-enumeration.
This time is increased to 20 ms to work with more USB HUBs.
Some SAM3S based board have external D+ pull-up mechanism (such as
SIMtrace) which needs to be used to pull D+ low.
This is a legacy mechanism from SAM7S history.
This mechanism is not required anymore on the SAM3S, and the qmod
does not use it. When the USB HAL is suspended, the transceiver is
disabled, causing D+ and D- to be pulled low. Then the HAL is activated
again. This is particularly required when DFU is started (and
enumerated), and after flashing the SAM3S switched to the main
application (without reset), so it can properly re-enumerate.
This board difference is now defined on the board header.
Change-Id: I9b58d8101c2fcf5595026b675728826af26127a3
Use USART 0 connected to the SIM card side to sniff the communication.
The card side can also measure ETU times.
Do proper pin initialization.
This code can already capture the ATR communication between phone and card.
Change-Id: I0597ec723cb2225540c89c3821b91d8a45adfcd6
This way we can easily check with 'diff' for differences in our code and
Atmel softpack. Also, this layout is more suitable for building various
different firmware images (e.g. factory-test, dfu-loader, main
application) for a variety of different boards (simtrace, owhw, qmod).
Harald Welte
Kevin Redon