sim-card
/
simtrace2
mirror of https://gerrit.osmocom.org/simtrace2
10
0
Fork 0
Code Issues Releases Wiki Activity
1,086 Commits 16 Branches 13 Tags 6.6 MiB
Commit Graph

143 Commits

Author SHA1 Message Date
Harald Welte 514c6d1da0 [firmware] wwan_perst: Print index when releasing WWAN_PERST 2017-11-03 20:40:56 +01:00
Harald Welte e7f2f9a5e0 [firmware] wwam_led: use 0/1 instead of 1/2 
most (all) other code modules have already moved over to
consistently using a 0-based index.
 2017-11-03 20:38:31 +01:00
Harald Welte 4e837d45db [firmware] card_pres: use modem number at start of line 
... like most other code modules, too
 2017-11-03 20:36:17 +01:00
Harald Welte b52b886186 [firmware] card_pres: Use 0/1 index number instead of 1/2 
We have moved most (all?) other code to work with slots 0/1
rather than 1/2.
 2017-11-03 20:33:10 +01:00
Harald Welte c47fc5febf set local slot LED according to remote/local state. 
The LED is illuminated as long as the slot is in local (physical SIM
card) mode.
 2017-05-20 14:46:57 +01:00
Harald Welte 02d0ec6e08 uart_console: Re-start watchdog during busy-waiting for serial chars 2017-05-20 14:46:57 +01:00
Harald Welte 253991789a dfu: make sure to not bloat the loader with main board init stuff. 2017-05-11 00:47:29 +02:00
Harald Welte 0709d2d842 perst/sim_switch: Log events using TRACE_INFO 2017-05-11 00:06:00 +02:00
Harald Welte 44622dfd8d consistently use 0-based counting of modems/slots 2017-05-11 00:04:50 +02:00
Harald Welte 5c583d3535 Generalize SIM switching code and allow local/remote switching via USB 2017-05-09 13:24:28 +02:00
Harald Welte 114e74d322 wwan_perst: Warn if somebody failed to initialize us 2017-05-09 13:24:28 +02:00
Harald Welte cb093ce878 wwan_perst: Support varying timeout and permanent active/inactive 2017-05-09 13:24:28 +02:00
Harald Welte ed1efc5035 qmod: debug_cmd: Avoid 'Unknown command' for valid commands 2017-05-07 23:10:02 +02:00
Harald Welte 28174982b6 qmod: Initialize ST12 specific I/O pins only on ST12 2017-05-07 23:10:02 +02:00
Harald Welte 8e7fca3255 migrate from req_ctx to msgb 
We now generalize the USB communiction and abandon the 'req_ctx'
structure inherited from openpcd.  Instead we use the libosmocore 'msgb'
structure to handle incoming and outgoing USB tranfers.  We also use
linuxlist-based msgb-queues for each endpoint.
 2017-05-07 23:09:56 +02:00
Harald Welte 6d1128e9d1 QMOD: Add code to determine SIM Card presence 2017-05-05 23:17:27 +02:00
Harald Welte 7e4390f181 qmod: wwan_led.c: Fix handling of LED for second Modem 2017-05-05 20:58:53 +02:00
Harald Welte 9164a6d335 qmod: Disable various console commands on ST34 
A number of commands related to the USB hub and the EEPROM are only
available on ST12, but not on ST34.  Let's remove them if not
applicable.
 2017-05-05 20:58:52 +02:00
Harald Welte 2cbc9b29f3 use same USB Product ID for DFU and runtime mode 
This was introduced for interoperability with operating systems that
might prefer such setup (I heard that Windows prefers this about a
decade ago, but I don't have any personal experience with it).

However, using different VID/PID between DFU and RT breaks usability of
dfu-util, and I really think this matters much more to our users and
developers.
 2017-05-05 00:34:28 +02:00
Harald Welte 353330dcc7 qmod: Fix polarity of SPDT switch 
the default boot state should be to use the local SIM, until the user
changes it (currently only possible via entering '!' or '@' on the
serial console).  The code so far had this completely inverted.
 2017-03-07 08:17:19 +01:00
Harald Welte abba8a8d85 LED: Introduce LED blinking pattern code 
It might be useful to display some different blinking patterns to
indicate specific system state (such as DFU mode vs. regular firmware)
 2017-03-06 16:58:00 +01:00
Harald Welte 912b183b29 qmod: Use different Interface Strings for Modem1+2 / Modem 3+4 
This makes it obvious in 'lsusb' and to other software on the USB host
which interface is for which of the modems.
 2017-03-06 09:28:13 +01:00
Harald Welte 809e5840f9 qmod: Add code to switch between physical and virtual SIM 2017-03-06 09:16:40 +01:00
Harald Welte 705e899e5f qmod: (re)activate USB port remapping. 
The port mapping is now as follows:

* port 1: ST12
* port 2: modem 1
* port 3: modem 2
* port 4: ST34
* port 5: modem 3
* port 6: modem 4
* port 7: daisy-chaining port
 2017-03-05 17:10:26 +01:00
Harald Welte 0e2959859a qmod: Replace hand-crafted delay loop with call to mdelay() 2017-03-05 16:48:47 +01:00
Harald Welte c6e482d581 qmod eeprom/i2c: Re-start watchdog while slow bit-banging 2017-03-05 16:24:29 +01:00
Harald Welte 1405100dff DFU: Introduce board/app-specific override for booting in DFU mode 
Using the USBDFU_OverrideEnterDFU() function, a board/application can
define extra conditions when the system should boot in DFU mode, even if
it was not explicitly switched to DFU mode from the application.

The app/dfu/main.c uses this mechanism to boot into DFU mode if the
stack + reset vector addresses are not plausible (i.e. some random junk
appears to be flashed in the application partition) or if the user
places a jumper accross the RxD+TxD lines of the debug UART.  The idea
is that the system can be recovered by placing this jumper and then
re-installing the application from DFU.
 2017-03-04 19:17:27 +01:00
Harald Welte aaba4af46c Use Supply Controller to avoid running SAM3 on voltages lower than 3.0V 
Sometimes there is some leakage current via some I/O that's sufficient
to power up the  SAM3S.  Use the supply monitor to make sure the CPU
will be reset (and kept in reset) if the supply voltage is below 3.0V.
 2017-03-03 18:48:13 +01:00
Harald Welte 3ecbf678db only simtrace is bus-powered, SAM3 on qmod + owhw are self-powered 2017-03-03 02:10:34 +01:00
Harald Welte f415d7163b Call USBD_Disconnect before software-triggered CPU reset 
This makes sure that we'll re-enumerate on the USB, as a CPU reset
apparently doesn't automatically release the pull-up and notify the hub
that we were gone?
 2017-03-03 01:51:43 +01:00
Harald Welte ec0837c463 change from \r\n (CRLF) to \n\r (LFCR) 
For some strange reason my output is garbled in both the 'screen' and
'cu' teerminal programs and 'raw' terminal (stty) mode.  I fail to
understand why, but let's simply adjust the code as needed for now.
 2017-03-03 01:33:24 +01:00
Harald Welte 91fc40240e DFU: make sure to properly initialize g_dfu pointer before using it 2017-03-03 01:05:22 +01:00
Harald Welte d1e963479e DFU: fix transitions between runtime and DFU mode 
we now always go through a processor reset to avoid any state that might
be persistent/left-over during the switch.
 2017-03-03 00:34:17 +01:00
Harald Welte db17e83960 cstartup: (re-)enable interrupts before calling main() 2017-03-02 23:19:13 +01:00
Harald Welte 0af4948211 cstartup / USBD: Use correct Makefile conditionals for DFU 2017-03-02 23:18:02 +01:00
Harald Welte cab66419d6 flashd: Set 6 Wait states as per Errata requiremens for Revision A 
It is utterly unacceptable that Atmel is shipping example code in 2011,
which doesn't support parts that are shipped still in 2016.  They would
have had five years to fix their code to implement the chip errata :(
 2017-03-02 19:22:50 +01:00
Harald Welte 0395bd15b3 move PLLB (for USB) initialization to board_lowlevel.c 
This way it is present both inside the DFU loader and in the main app.
 2017-02-28 01:28:56 +01:00
Harald Welte adba0ce80b fix g_dfu access from both DFU and runtime access 
We need to refer to g_dfu as a pointer from all code.  In DFU mode, it
gets assigned to the address of _g_dfu, which is placed by the linker
script at the start of RAM.  In runtime mode, the pointer is statically
defined to point at the start of RAM.  The linker script for the runtime
(dfu environment) is adjusted to save the first 32 bytes for the _g_dfu
structure.
 2017-02-28 01:10:32 +01:00
Harald Welte 65cca7cccc ensure g_dfu is linked to start of RAM when building DFU loader 2017-02-28 01:10:27 +01:00
Harald Welte 32852bc1d9 DFU: towards a more complete implementation 
* we now actually route the EP0 control requests in DFU mode to the
  correct handler (weak linker symbols are tricky)
* we now actually call code to read/write data from/to RAM/FLASH
 2017-02-28 01:10:23 +01:00
Harald Welte d09829dcc6 Remove newlib dependency, include own stdio/string/assert 2017-02-27 23:00:26 +01:00
Harald Welte d8a003dfd7 Structure build system to build for multiple boards/apps/environments 2017-02-27 22:18:45 +01:00
Harald Welte 3f5e3ddffc Change directory structure to align with Atmel softpack 
This way we can easily check with 'diff' for differences in our code and
Atmel softpack.  Also, this layout is more suitable for building various
different firmware images (e.g. factory-test, dfu-loader, main
application) for a variety of different boards (simtrace, owhw, qmod).
 2017-02-27 14:24:11 +01:00