mirror of https://gerrit.osmocom.org/simtrace2
SIMtrace board: comment and fix pin definition
This commit is contained in:
parent
aa70887ce0
commit
5a7c848b43
|
|
@ -1,88 +1,112 @@
|
|||
#pragma once
|
||||
#include "board_common.h"
|
||||
|
||||
/** Name of the board */
|
||||
/* Name of the board */
|
||||
#define BOARD_NAME "SAM3S-SIMTRACE"
|
||||
/** Board definition */
|
||||
/* Board definition */
|
||||
#define simtrace
|
||||
|
||||
/* Board main oscillator frequency (in Hz) */
|
||||
#define BOARD_MAINOSC 18432000
|
||||
|
||||
/** Phone (SIM card emulator)/CCID Reader/MITM configuration **/
|
||||
/* Normally the communication lines between phone and SIM card are disconnected */
|
||||
// Disconnect SIM card I/O, VPP line from the phone lines
|
||||
// FIXME: Per default pins are input, therefore high-impedance, therefore the bus switch is in an unknown state by default for hardware version <= 1.4. It should be pulled high by an external resistor to set the bus switch to high-impedance (e.g. off).
|
||||
#define PIN_SC_SW_DEFAULT {PIO_PA20, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
// Disconnect SIM card RST, CLK line from the phone lines
|
||||
#define PIN_IO_SW_DEFAULT {PIO_PA19, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
#define PINS_BUS_DEFAULT PIN_SC_SW_DEFAULT, PIN_IO_SW_DEFAULT
|
||||
/** Pin configuration **/
|
||||
/* Button to force bootloader start (shorted to ground when pressed */
|
||||
#define PIN_BOOTLOADER_SW {PIO_PA31, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP}
|
||||
/* Enable powering the card using the second 3.3 V output of the LDO (active high) */
|
||||
#define SIM_PWEN_PIN {SIM_PWEN, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
/* Card presence pin */
|
||||
#define SW_SIM PIO_PA8
|
||||
/* Pull card presence pin high (shorted to ground in card slot when card is present) */
|
||||
#define SMARTCARD_CONNECT_PIN {SW_SIM, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP | PIO_DEBOUNCE | PIO_DEGLITCH | PIO_IT_EDGE }
|
||||
|
||||
/** Smart card connection **/
|
||||
/* Card RST reset signal input (active low; RST_SIM in schematic) */
|
||||
#define PIN_ISO7816_RSTMC {PIO_PA7, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
/* Card I/O data signal input/output (I/O_SIM in schematic) */
|
||||
#define PIN_SIM_IO {PIO_PA6A_TXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
/* Card CLK clock input (CLK_SIM in schematic) */
|
||||
#define PIN_SIM_CLK {PIO_PA2B_SCK0, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
|
||||
/* ISO7816-communication related pins */
|
||||
#define PINS_ISO7816 PIN_SIM_IO, PIN_SIM_CLK, PIN_ISO7816_RSTMC // SIM_PWEN_PIN, PIN_SIM_IO2, PIN_SIM_CLK2
|
||||
/* Pin to measure card I/O timing (to start measuring the ETU on I/O activity; connected I/O_SIM in schematic) */
|
||||
#define PIN_SIM_IO_INPUT {PIO_PA1B_TIOB0, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
|
||||
/* Pin used as clock input (to measure the ETU duration; connected to CLK_SIM in schematic) */
|
||||
#define PIN_SIM_CLK_INPUT {PIO_PA4B_TCLK0, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
|
||||
/* Pins used to measure ETU timing (using timer counter) */
|
||||
#define PINS_TC PIN_SIM_IO_INPUT, PIN_SIM_CLK_INPUT
|
||||
|
||||
/** Phone connection **/
|
||||
/* Phone USIM slot 1 VCC pin (VCC_PHONE in schematic) */
|
||||
#define PIN_USIM1_VCC {PIO_PA25, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
|
||||
/* Phone USIM slot 1 RST pin (active low; RST_PHONE in schematic) */
|
||||
#define PIN_USIM1_nRST {PIO_PA24, PIOA, ID_PIOA, PIO_INPUT, PIO_IT_RISE_EDGE | PIO_DEGLITCH }
|
||||
/* Phone I/O data signal input/output (I/O_PHONE in schematic) */
|
||||
#define PIN_PHONE_IO {PIO_PA22A_TXD1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
/* Phone CLK clock input (CLK_PHONE in schematic) */
|
||||
#define PIN_PHONE_CLK {PIO_PA23A_SCK1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
/* Pin used for phone USIM slot 1 communication */
|
||||
#define PINS_USIM1 PIN_PHONE_IO, PIN_PHONE_CLK, PIN_PHONE_CLK_INPUT, PIN_USIM1_VCC, PIN_PHONE_IO_INPUT, PIN_USIM1_nRST
|
||||
/* Phone I/O data signal input/output (unused USART RX input; connected to I/O_PHONE in schematic) */
|
||||
#define PIN_PHONE_IO_INPUT {PIO_PA21A_RXD1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
/* Pin used as clock input (to measure the ETU duration; connected to CLK_PHONE in schematic) */
|
||||
#define PIN_PHONE_CLK_INPUT {PIO_PA29B_TCLK2, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
|
||||
|
||||
/** Default configuration **/
|
||||
/* Disconnect VPP, CLK, and RST lines between card and phone using bus switch (high sets bus switch to high-impedance) */
|
||||
#define PIN_SC_SW_DEFAULT {PIO_PA20, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
/* Disconnect I/O line between card and phone using bus switch (high sets bus switch to high-impedance) */
|
||||
#define PIN_IO_SW_DEFAULT {PIO_PA19, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
/* Disconnect all lines (VPP, CLK, RST, and I/O) between card and phone */
|
||||
#define PINS_BUS_DEFAULT PIN_SC_SW_DEFAULT, PIN_IO_SW_DEFAULT
|
||||
|
||||
/** Sniffer configuration **/
|
||||
// Connect VPP, CLK and RST lines from smartcard to the phone
|
||||
/* Connect VPP, CLK, and RST lines between card and phone using bus switch (low connects signals on bus switch) */
|
||||
#define PIN_SC_SW_SNIFF {PIO_PA20, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
/* Connect I/O line between card and phone using bus switch (low connects signals on bus switch) */
|
||||
#define PIN_IO_SW_SNIFF {PIO_PA19, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
/* Connect all lines (VPP, CLK, RST, and I/O) between card and phone */
|
||||
#define PINS_BUS_SNIFF PIN_SC_SW_SNIFF, PIN_IO_SW_SNIFF
|
||||
|
||||
/* Pins used to sniff phone-card communication */
|
||||
#define PINS_SIM_SNIFF_SIM PIN_PHONE_IO, PIN_PHONE_CLK
|
||||
/* Disable power converter 4.5-6V to 3.3V; (active high) */
|
||||
#define PIN_SIM_PWEN_SNIFF {SIM_PWEN, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
/* Enable power switch: VCC_PHONE to VCC_SIM; (active high) */
|
||||
#define PIN_VCC_FWD_SNIFF {VCC_FWD, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
/* Use phone VCC to power card */
|
||||
#define PWR_PINS PIN_SIM_PWEN_SNIFF, PIN_VCC_FWD_SNIFF
|
||||
|
||||
#define SIM_PWEN_PIN {PIO_PA5, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
|
||||
#define PWR_PINS \
|
||||
/* Enable power converter 4.5-6V to 3.3V; low: off */ \
|
||||
{SIM_PWEN, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}, \
|
||||
/* Enable second power converter: VCC_PHONE to VCC_SIM; high: on */ \
|
||||
{VCC_FWD, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
|
||||
#define SW_SIM PIO_PA8
|
||||
#define SMARTCARD_CONNECT_PIN {SW_SIM, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP | PIO_DEBOUNCE | PIO_DEGLITCH | PIO_IT_EDGE }
|
||||
//#define SMARTCARD_CONNECT_PIN {SW_SIM, PIOB, ID_PIOB, PIO_INPUT, PIO_PULLUP | PIO_DEBOUNCE | PIO_IT_EDGE}
|
||||
|
||||
/// PIN used for resetting the smartcard
|
||||
// FIXME: Card is resetted with pin set to 0 --> PIO_OUTPUT_1 as default is right?
|
||||
#define PIN_ISO7816_RSTMC {PIO_PA7, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
|
||||
/// Pins used for connect the smartcard
|
||||
#define PIN_SIM_IO_INPUT {PIO_PA1, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
|
||||
#define PIN_SIM_IO {PIO_PA6, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
#define PIN_SIM_CLK {PIO_PA2, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
|
||||
#define PIN_SIM_CLK_INPUT {PIO_PA4, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
|
||||
//#define PINS_ISO7816 PIN_USART1_TXD, PIN_USART1_SCK, PIN_ISO7816_RSTMC
|
||||
#define PINS_ISO7816 PIN_SIM_IO, PIN_SIM_CLK, PIN_ISO7816_RSTMC // SIM_PWEN_PIN, PIN_SIM_IO2, PIN_SIM_CLK2
|
||||
|
||||
#define PINS_TC PIN_SIM_IO_INPUT, PIN_SIM_CLK_INPUT
|
||||
|
||||
#define PIN_USIM1_VCC {PIO_PA25, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
|
||||
#define PIN_USIM1_nRST {PIO_PA24, PIOA, ID_PIOA, PIO_INPUT, PIO_IT_RISE_EDGE | PIO_DEGLITCH }
|
||||
#define PIN_PHONE_IO_INPUT {PIO_PA21, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
|
||||
#define PIN_PHONE_IO {PIO_PA22, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
#define PIN_PHONE_CLK {PIO_PA23A_SCK1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT} // External Clock Input on PA28
|
||||
//#define PIN_PHONE_CLK {PIO_PA23A_SCK1, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT} // External Clock Input on PA28
|
||||
#define PIN_PHONE_CLK_INPUT {PIO_PA29, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
|
||||
#define PINS_USIM1 PIN_PHONE_IO, PIN_PHONE_CLK, PIN_PHONE_CLK_INPUT, PIN_USIM1_VCC, PIN_PHONE_IO_INPUT, PIN_USIM1_nRST
|
||||
//, VCC_PHONE
|
||||
|
||||
#define PIN_BOOTLOADER_SW {PIO_PA31, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP}
|
||||
|
||||
//** SPI interface **/
|
||||
/// SPI MISO pin definition (PA12).
|
||||
#define PIN_SPI_MISO {1 << 12, PIOA, PIOA, PIO_PERIPH_A, PIO_PULLUP}
|
||||
/// SPI MOSI pin definition (PA13).
|
||||
#define PIN_SPI_MOSI {1 << 13, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
/// SPI SPCK pin definition (PA14).
|
||||
#define PIN_SPI_SPCK {1 << 14, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
/// SPI pins definition. Contains MISO, MOSI & SPCK (PA12, PA13 & PA14).
|
||||
#define PINS_SPI PIN_SPI_MISO, PIN_SPI_MOSI, PIN_SPI_SPCK
|
||||
/// SPI chip select 0 pin definition (PA11).
|
||||
#define PIN_SPI_NPCS0 {1 << 11, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
/** External SPI flash interface **/
|
||||
/* SPI MISO pin definition */
|
||||
#define PIN_SPI_MISO {PIO_PA12A_MISO, PIOA, PIOA, PIO_PERIPH_A, PIO_PULLUP}
|
||||
/* SPI MOSI pin definition */
|
||||
#define PIN_SPI_MOSI {PIO_PA13A_MOSI, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
/* SPI SCK pin definition */
|
||||
#define PIN_SPI_SCK {PIO_PA14A_SPCK, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
/* SPI pins definition. Contains MISO, MOSI & SCK */
|
||||
#define PINS_SPI PIN_SPI_MISO, PIN_SPI_MOSI, PIN_SPI_SCK
|
||||
/* SPI chip select 0 pin definition */
|
||||
#define PIN_SPI_NPCS0 {PIO_PA11A_NPCS0, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
/* SPI flash write protect pin (active low, pulled low) */
|
||||
#define PIN_SPI_WP {PA15, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
|
||||
/** USB definitions */
|
||||
/* OpenMoko SIMtrace 2 USB vendor ID */
|
||||
#define BOARD_USB_VENDOR_ID USB_VENDOR_OPENMOKO
|
||||
/* OpenMoko SIMtrace 2 USB product ID (main application/runtime mode) */
|
||||
#define BOARD_USB_PRODUCT_ID USB_PRODUCT_SIMTRACE2
|
||||
/* OpenMoko SIMtrace 2 DFU USB product ID (DFU bootloader/DFU mode) */
|
||||
#define BOARD_DFU_USB_PRODUCT_ID USB_PRODUCT_SIMTRACE2_DFU
|
||||
/* USB release number (bcdDevice, shown as 0.00) */
|
||||
#define BOARD_USB_RELEASE 0x000
|
||||
/* Indicate SIMtrace is bus power in USB attributes */
|
||||
#define BOARD_USB_BMATTRIBUTES USBConfigurationDescriptor_BUSPOWERED_NORWAKEUP
|
||||
|
||||
#define BOARD_USB_VENDOR_ID USB_VENDOR_OPENMOKO
|
||||
#define BOARD_USB_PRODUCT_ID USB_PRODUCT_SIMTRACE2
|
||||
#define BOARD_DFU_USB_PRODUCT_ID USB_PRODUCT_SIMTRACE2_DFU
|
||||
#define BOARD_USB_RELEASE 0x000
|
||||
|
||||
/** Supported modes */
|
||||
/* SIMtrace board supports sniffer mode */
|
||||
#define HAVE_SNIFFER
|
||||
/* SIMtrace board supports CCID mode */
|
||||
#define HAVE_CCID
|
||||
/* SIMtrace board supports card emulation mode */
|
||||
#define HAVE_CARDEM
|
||||
/* SIMtrace board supports man-in-the-middle mode */
|
||||
//#define HAVE_MITM
|
||||
|
|
|
|||
Loading…
Reference in New Issue