doc: Copy Kevin's hardware section into the documentation
This commit is contained in:
parent
0c387d5882
commit
b230ec61fc
|
@ -0,0 +1,86 @@
|
|||
<?xml version="1.0" encoding="UTF-8"?>
|
||||
<chapter id="chapter_hw">
|
||||
<title>Getting and Building the Software</title>
|
||||
<section id="pcb_populated">
|
||||
<title>Populated PCB</title>
|
||||
<para>The version v1.0p is the first production that had an
|
||||
automatic SMT run. Due some production issues the labeling of
|
||||
components didn't make it to the PCB but can be found in this
|
||||
manual. The difference between the v1.0 and v1.0p hardware is
|
||||
in the footprint of some components to utilize the existing
|
||||
stock of the factory. This was mostly done for the LED and the
|
||||
shottky diodes.</para>
|
||||
|
||||
<figure><title>SIMtrace v1.0 PCB</title>
|
||||
<mediaobject>
|
||||
<imageobject>
|
||||
<imagedata fileref="images/simtrace_hw.jpg" width="15cm"/>
|
||||
</imageobject>
|
||||
<textobject><phrase>SIMtrace v1.0 PCB</phrase></textobject>
|
||||
</mediaobject>
|
||||
</figure>
|
||||
</section>
|
||||
|
||||
<section id="pcb_surface">
|
||||
<title>PCB Surface</title>
|
||||
<para>
|
||||
<figure><title>SIMtrace v1.0 Surface</title>
|
||||
<mediaobjectco>
|
||||
<imageobjectco>
|
||||
<areaspec id="surface" units="calspair">
|
||||
<area linkends="link_usb" coords="8800,0 8800,6100" id="usb"/>
|
||||
<area linkends="link_serial" coords="8800,7000 8800,8000" id="serial"/>
|
||||
<area linkends="link_debug" coords="8800,9000 8800,9500" id="debug"/>
|
||||
<area linkends="link_jtag" coords="5000,8900 5000,9000" id="jtag"/>
|
||||
<area linkends="link_bt1" coords="8900,0 9100,3500" id="bt1"/>
|
||||
<area linkends="link_ffc" coords="500,3000 700,9000" id="ffc"/>
|
||||
<area linkends="link_sim" coords="500,500 700,2000" id="sim"/>
|
||||
<area linkends="link_reset" coords="200,9000 500,9000" id="reset"/>
|
||||
<area linkends="link_bootloader" coords="1700,9000 1900,9000" id="bootloader"/>
|
||||
<area linkends="link_test" coords="6500,8700 7000,8900" id="test"/>
|
||||
<area linkends="link_erase" coords="7100,8700 7600,8900" id="erase"/>
|
||||
</areaspec>
|
||||
<imageobject>
|
||||
<imagedata fileref="images/simtrace_surface.png" width="15cm" />
|
||||
</imageobject>
|
||||
<calloutlist>
|
||||
<callout arearefs="usb" id="link_usb">
|
||||
<para>USB: USB mini-B connector. The main connector. The host software communicates (sniffing,...) through USB with the board. It can also be used to flash the micro-controller (using DFU).</para>
|
||||
</callout>
|
||||
<callout arearefs="serial" id="link_serial">
|
||||
<para>serial: 2.5 mm jack serial cable, as used by osmocomBB. port used to debug the device (printf goes there).</para>
|
||||
</callout>
|
||||
<callout arearefs="debug" id="link_debug">
|
||||
<para>debug (P3): same as serial, but using the FTDI serial cable.</para>
|
||||
</callout>
|
||||
<callout arearefs="jtag" id="link_jtag">
|
||||
<para>jtag (P1): JTAG 20 pin connector to do hardware assisted debugging.</para>
|
||||
</callout>
|
||||
<callout arearefs="bt1" id="link_bt1">
|
||||
<para>BT1: battery connector (4.5-6V DC). normally the USB provides power, but the battery port can be used for autonomous use of SIMtrace. The sniffing can be saved in the flash (U1).</para>
|
||||
</callout>
|
||||
<callout arearefs="ffc" id="link_ffc">
|
||||
<para>FFC_SIM (P3): to connect the flat flexible cable with SIM end for the phone.</para>
|
||||
</callout>
|
||||
<callout arearefs="sim" id="link_sim">
|
||||
<para>SIM (P4): put your SIM in there (instead of in the phone)</para>
|
||||
</callout>
|
||||
<callout arearefs="reset" id="link_reset">
|
||||
<para>reset (SW1): to reset the board (not erasing the firmware). If your are too lazy to unplug and re-plug the USB.</para>
|
||||
</callout>
|
||||
<callout arearefs="bootloader" id="link_bootloader">
|
||||
<para>bootloader (SW2): used to start the bootloader so to flash the device using DFU. press when plugging in the USB.</para>
|
||||
</callout>
|
||||
<callout arearefs="test" id="link_test">
|
||||
<para>test (JP1): short circuit using a jumper to flash using SAM-BA.</para>
|
||||
</callout>
|
||||
<callout arearefs="erase" id="link_erase">
|
||||
<para>erase (JP2): short circuit using a jumper to erase completely erase the firmware.</para>
|
||||
</callout>
|
||||
</calloutlist>
|
||||
</imageobjectco>
|
||||
</mediaobjectco>
|
||||
</figure>
|
||||
</para>
|
||||
</section>
|
||||
</chapter>
|
Binary file not shown.
After Width: | Height: | Size: 823 KiB |
Binary file not shown.
After Width: | Height: | Size: 61 KiB |
|
@ -7,6 +7,7 @@
|
|||
"http://www.oasis-open.org/docbook/xml/4.2/docbookx.dtd" [
|
||||
<!ENTITY chapter-introduction SYSTEM "chapters/introduction.xml">
|
||||
<!ENTITY chapter-installation SYSTEM "chapters/installation.xml">
|
||||
<!ENTITY chapter-hw-details SYSTEM "chapters/hardware_details.xml">
|
||||
<!ENTITY chapter-using SYSTEM "chapters/using.xml">
|
||||
<!ENTITY chapter-building SYSTEM "chapters/building.xml">
|
||||
<!ENTITY chapter-appendix SYSTEM "chapters/appendix.xml">
|
||||
|
@ -21,6 +22,12 @@
|
|||
<authorinitials>z</authorinitials>
|
||||
<revremark>Initial</revremark>
|
||||
</revision>
|
||||
<revision>
|
||||
<revnumber>0.0.2</revnumber>
|
||||
<date>14 August 2011</date>
|
||||
<authorinitials>z</authorinitials>
|
||||
<revremark>Copy HW Info from the Wiki</revremark>
|
||||
</revision>
|
||||
</revhistory>
|
||||
|
||||
<title>SIMtrace Usermanual</title>
|
||||
|
@ -41,6 +48,7 @@
|
|||
<!-- Main chapters-->
|
||||
&chapter-introduction;
|
||||
&chapter-installation;
|
||||
&chapter-hw-details;
|
||||
&chapter-using;
|
||||
&chapter-building;
|
||||
|
||||
|
|
Loading…
Reference in New Issue