Drop the open-coded MAC assignment from net_init_nic and replace it with
standard qemu_macaddr_default_if_unset which is also used by qdev. That
avoid creating colliding MACs when instantiating NICs via different
mechanisms.
This change requires to store the MAC as MACAddr in NICInfo, and the
remaining nd_table users need to be updated.
Based on suggestion by Peter Maydell.
CC: Markus Armbruster <armbru@redhat.com>
CC: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Position entries of net_client_types according to the corresponding
values of NET_CLIENT_TYPE_*. The array size is now defined by
NET_CLIENT_TYPE_MAX. This will allow to obtain entries based on type
value in later patches.
At this chance rename NET_CLIENT_TYPE_SLIRP to NET_CLIENT_TYPE_USER for
the sake of consistency.
CC: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Diagnose the case where the user asked for a NIC via "-net nic"
but the board didn't instantiate that NIC (for example where the
user asked for two NICs but the board only supports one). Note
that this diagnostic doesn't apply to NICs created through -device,
because those are always instantiated.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If bootindex is specified on command line a string that describes device
in firmware readable way is added into sorted list. Later this list will
be passed into firmware to control boot order.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
With -netdev, virtio devices present offload
features to guest, depending on the backend used.
Thus, removing host netdev peer while guest is
active leads to guest-visible inconsistency and/or crashes.
As a solution, while guest (NIC) peer device exists,
we prevent the host peer from being deleted.
This patch does this by adding peer_deleted flag in nic state:
if host device is going away while guest device
is around, set this flag and keep a shell of
the host device around for as long as guest device exists.
The link is put down so all packets will get discarded.
At the moment, management can detect that device deletion
is delayed by doing info net. As a next step, we shall add
commands that control hotplug/unplug without
removing the device, and an event to report that
guest has responded to the hotplug event.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
There are many problems with net_set_boot_mask():
1) It is broken when using the device model instead of "-net nic". Example:
$ qemu-system-x86_64 -device rtl8139,vlan=0,id=net0,mac=52:54:00:82:41:fd,bus=pci.0,addr=0x4 -net user,vlan=0,name=hostnet0 -vnc 0.0.0.0:0 -boot n
Cannot boot from non-existent NIC
$
2) The mask was previously used to set which boot ROMs were supposed to be
loaded, but this was changed long time ago. Now all ROM images are loaded,
and SeaBIOS takes care of jumping to the right boot entry point depending on
the boot settings.
3) Interpretation and validation of the boot parameter letters is done on
the machine type code. Examples: PC accepts only a,b,c,d,n as valid boot
device letters. mac99 accepts only a,b,c,d,e,f.
As a side-effect of this change, qemu-kvm won't abort anymore if using "-boot n"
on a machine with no network devices. Checking if the requested boot device is
valid is now a task for the BIOS or the machine-type code.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
It is just set by net_set_boot_mask() and never used. The logic for rom loading
changed a lot since this field was introduced. It is not needed anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
net.c used a constant to signify no MSI vectors were specified. Extend
that to all qdev devices.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reported-by: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
net_check_clients() prints this when an VLAN has host devices, but no
guest devices. It uses VLANState members nb_guest_devs and
nb_host_devs to keep track of these devices. However, -device does
not update nb_guest_devs, only net_init_nic() does that, for -net nic.
Check the VLAN clients directly, and remove the counters.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Call it right after -device devices get created.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When vhost is bound to a backend device, we need to stop polling it when
vhost is started, and restart polling when vhost is stopped.
Add an API for that for use by vhost, and implement in tap backend.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add a default_net variable which specified whenever a default network
should be created. It is cleared in case any -net option is specified
and it is also added to the new -nodefaults switch.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add a NetClientInfo pointer to VLANClientState and use that
for the typecode and function pointers.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
... and VLANClientState::opaque and qemu_find_vlan_client().
All of these are now unused
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Common state for all NICs.
The opaque member will replace the opaque member in VLANClientState
since only NICs need it.
The conf member will allow us to iterate over NICs, access the MAC
addr for the NIC and send a packet from each NIC in qemu_announce_self().
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
A replacement for qemu_new_vlan_client(), using NetClientInfo to
replace most arguments.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This structure holds data which is common to all instances of a given
net client type/model.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since 1cc33683, this field is not set for most devices, so just
remove it and its remaining few uses.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If a receiver returns zero, that means its queue is full and it will
notify us when room is available using qemu_flush_queued_packets().
Take note of that and disable that receiver until it flushes its queue.
This is a first step towards allowing can_receive() handlers to return
true even if no buffer space is available.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Enable UFO on the host tap device if supported and allow setting UFO
on virtio-net in the guest.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This API allows virtio-net to enable various offload features on a
tap interface - e.g. to tell the host kernel it can pass up partial
checksums to userspace.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Trivial patch to allow supplying a receive_raw function.
A future cleanup should combine this function pointer parameters into a
table.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In the case where a NIC and backend agree on a packet header format,
this API allows injecting packets which lack the agreed upon header.
We need this for sending our gratuitous ARP.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
These lamely named functions allow virtio-net to query whether
IFF_VNET_HDR is enabled on a tap interface and inform the tap code
that virtio-net will supply packets with a vnet header.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This is so as to allow APIs which operate on specific client types
without having to add a function table entry which is only implemented
by a single client type.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add a new type for properties common to all nics.
Add helper functions and macros to deal with it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add new type for mac addresses.
Add function which sets the qemu default mac address if it finds the mac
address uninitialized (i.e. all zeros).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Now that we have re-factored the packet queue code, we can re-use
it for peer-to-peer also.
Patchworks-ID: 35520
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The packet queue code is fairly standalone, has some complex details and
easily reusable. It makes sense to split it out on its own. This patch
doesn't contain any functional changes.
Patchworks-ID: 35511
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Introduce a 'peer' member to VLANClientState as an alternative
to a vlan. The idea being that packets are transfered directly
from peer clients rather than going through a vlan.
Patchworks-ID: 35516
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Same as for -net except for:
- only tap, user, vde and socket types are supported
- the vlan parameter is not allowed
- the name parameter is not allowed but the id parameter is
required
Patchworks-ID: 35517
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just use the name field instead since we now use the id paramater as
the name, if supplied. Only implication with this change is that if
id is not supplied, the value of the name paramater is used as an
id.
Patchworks-ID: 35512
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Jan Kiszka