The page control (PC) field defines the type of mode parameter values
to be returned in the mode pages:
PC=0 : Current values
PC=1 : Changeable values
PC=2 : Default values
PC=3 : Saved values
The current implementation always returns the same type of parameters.
This is OK for Current and Default values as we don't support changes
to be done by the MODE SELECT command.
For Saved values the following applies (implemented by this patch):
"A PC field value of 3h requests that the target return the saved
values of the mode parameters. Implementation of saved page parameters
is optional. Mode parameters not supported by the target shall be set
to zero. If saved values are not implemented, the command shall be
terminated with CHECK CONDITION status, the sense key set to
ILLEGAL REQUEST and the additional sense code set to
SAVING PARAMETERS NOT SUPPORTED."
For Changeable values the following applies (implemented by this patch):
"A PC field value of 1h requests that the target return a mask denoting
those mode parameters that are changeable. In the mask, the fields of
the mode parameters that are changeable shall be set to all one bits and
the fields of the mode parameters that are non-changeable (i.e. defined
by the target) shall be set to all zero bits."
In newer versions of the SCSI-2 spec the following clause was added.
"If the logical unit does not implement changeable parameters mode pages
and the device server receives a MODE SENSE command with 01b in the PC
field, then the command shall be terminated with CHECK CONDITION status,
with the sense key set to ILLEGAL REQUEST, and the additional sense code
set to INVALID FIELD IN CDB."
This was not yet included in the SCSI-2 Working Drafts from 1986-1993.
I assume that the variant to return CHECK CONDITION for PC=1 is not
widely implemented by real devices. I have a legacy OS which fails,
if MODE_SENSE returns non GOOD for PC=1. So for highest compatibility I
implemented the former variant with this patch.
The last Working Draft X3T9.2 Rev. 10L 7-SEP-93 can be found here:
http://ldkelley.com/SCSI2/SCSI2/SCSI2-08.html#8.2.10
In mode_sense_page() this patch also avoids multiple hard coded
definitions of the same mode page length. Instead I use the varable
p[1]. In fact the returned length of the mode pages 4 and 5 were wrong
(2 bytes less).
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The header for the MODE SENSE(10) command is 8 bytes long.
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The MODE DATA LENGTH field indicates the length in bytes of the following
data that is available to be transferred. The mode data length does not include
the number of bytes in the MODE DATA LENGTH field.
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Changing block.h or blockdev.h resulted in recompiling most objects.
Move DriveInfo typedef and BlockInterfaceType enum definitions
to qemu-common.h and rearrange blockdev.h use to decrease churn.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Disks without media make no sense. For SCSI, a Linux guest kernel
complains during boot. I didn't try other combinations.
scsi-generic doesn't need the additional check, because it already
requires bdrv_is_sg(), which fails without media.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
drive_init() doesn't permit rerror for if=scsi, but that's worthless:
we get it via if=none and -device.
Moreover, scsi-generic doesn't support werror. Since drive_init()
doesn't catch that, option werror was silently ignored even with
if=scsi.
Wart: unlike drive_init(), we don't reject the default action when
it's explicitly specified. That's because we can't distinguish "no
rerror option" from "rerror=report", or "no werror" from
"rerror=enospc". Left for another day.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BlockDriverState member removable controls whether virtual media
change (monitor commands change, eject) is allowed. It is set when
the "type hint" is BDRV_TYPE_CDROM or BDRV_TYPE_FLOPPY.
The type hint is only set by drive_init(). It sets BDRV_TYPE_FLOPPY
for if=floppy. It sets BDRV_TYPE_CDROM for media=cdrom and if=ide,
scsi, xen, or none.
if=ide and if=scsi work, because the type hint makes it a CD-ROM.
if=xen likewise, I think.
For the same reason, if=none works when it's used by ide-drive or
scsi-disk. For other guest devices, there are problems:
* fdc: you can't change virtual media
$ qemu [...] -drive if=none,id=foo,... -global isa-fdc.driveA=foo
QEMU 0.12.50 monitor - type 'help' for more information
(qemu) eject foo
Device 'foo' is not removable
unless you add media=cdrom, but that makes it readonly.
* virtio: if you add media=cdrom, you can change virtual media. If
you eject, the guest gets I/O errors. If you change, the guest sees
the drive's contents suddenly change.
* scsi-generic: if you add media=cdrom, you can change virtual media.
I didn't test what that does to the guest or the physical device,
but it can't be pretty.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make the property point to BlockDriverState, cutting out the DriveInfo
middleman. This prepares the ground for block devices that don't have
a DriveInfo.
Currently all user-defined ones have a DriveInfo, because the only way
to define one is -drive & friends (they go through drive_init()).
DriveInfo is closely tied to -drive, and like -drive, it mixes
information about host and guest part of the block device. I'm
working towards a new way to define block devices, with clean
host/guest separation, and I need to get DriveInfo out of the way for
that.
Fortunately, the device models are perfectly happy with
BlockDriverState, except for two places: ide_drive_initfn() and
scsi_disk_initfn() need to check the DriveInfo for a serial number set
with legacy -drive serial=... Use drive_get_by_blockdev() there.
Device model code should now use DriveInfo only when explicitly
dealing with drives defined the old way, i.e. without -device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We automatically delete blockdev host parts on unplug of the guest
device. Too much magic, but we can't change that now.
The delete happens early in the guest device teardown, before the
connection to the host part is severed. Thus, the guest part's
pointer to the host part dangles for a brief time. No actual harm
comes from this, but we'll catch such dangling pointers a few commits
down the road. Clean up the dangling pointers by delaying the
automatic deletion until the guest part's pointer is gone.
Device usb-storage deliberately makes two qdev properties refer to the
same drive, because it automatically creates a second device. Again,
too much magic we can't change now. Multiple references worked okay
before, but now free_drive() dies for the second one. Zap the extra
reference.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
That's where they belong semantically (block device host part), even
though the actions are actually executed by guest device code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Anything that moves hundreds of lines out of vl.c can't be all bad.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Show the actual default value instead of <null> when the property has
not been set.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It needs to be a qdev property, because it belongs to the drive's
guest part.
Bonus: info qtree now shows the serial number.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Once the I/O completion callback returned, aiocb will be released by the
controller. So we have to clear the reference not only in
scsi_write_complete, but also in scsi_read_complete. Otherwise we risk
inconsistencies when a reset hits us before the related request is
released.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Ensure that pending requests of an SCSI disk are purged on system reset
and also restore max_lba. The latter is no only present in the reset
handler as that one is called after init as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In case s->version is shorter than 4 bytes we overflow the memcpy src
buffer. Fix it by clearing the target buffer, then copy only the
amount of bytes we actually have.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Don't rely on CDROM hint for read_only attribute
Signed-off-by: Naphtali Sprei <nsprei@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add a logical block size attribute as various guest side tools only
increase the filesystem sector size based on it, not the advisory
physical block size.
For scsi we already have support for a different logical block size
in place for CDROMs that we can built upon. Only my recent block
device characteristics VPD page needs some fixups. Note that we
leave the logial block size for CDROMs hardcoded as the 2k value
is expected for it in general.
For virtio-blk we already have a feature flag claiming to support
a variable logical block size that was added for the s390 kuli
hypervisor. Interestingly it does not actually change the units
in which the protocol works, which is still fixed at 512 bytes,
but only communicates a different minimum I/O granularity. So
all we need to do in virtio is to add a trap for unaligned I/O
and round down the device size to the next multiple of the logical
block size.
IDE does not support any other logical block size than 512 bytes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
error_report() terminates the message with a newline. Strip it it
from its arguments.
This fixes a few error messages lacking a newline:
net_handle_fd_param()'s "No file descriptor named %s found", and
tap_open()'s "vnet_hdr=1 requested, but no kernel support for
IFF_VNET_HDR available" (all three versions).
There's one place that passes arguments without newlines
intentionally: load_vmstate(). Fix it up.
You're supposed to use scsi-generic for that. Which rejects anything
but /dev/sg*.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The next commit will move the STOP event into do_vm_stop(), to
have the expected event sequence we need to emit the I/O error
event before calling vm_stop().
The expected sequence is:
{ "event": "BLOCK_IO_ERROR" [...] }
{ "event": "STOP" }
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Export the physical block size in the READ CAPACITY (16) command,
and add the new block limits VPD page to export the minimum and
optiomal I/O sizes.
Note that we also need to bump the scsi revision level to SPC-2
as that is the minimum requirement by at least the Linux kernel
to try READ CAPACITY (16) first and look at the block limits VPD
page.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add three new qdev properties to export block topology information to
the guest. This is needed to get optimal I/O alignment for RAID arrays
or SSDs.
The options are:
- physical_block_size to specify the physical block size of the device,
this is going to increase from 512 bytes to 4096 kilobytes for many
modern storage devices
- min_io_size to specify the minimal I/O size without performance impact,
this is typically set to the RAID chunk size for arrays.
- opt_io_size to specify the optimal sustained I/O size, this is
typically the RAID stripe width for arrays.
I decided to not auto-probe these values from blkid which might easily
be possible as I don't know how to deal with these issues on migration.
Note that we specificly only set the physical_block_size, and not the
logial one which is the unit all I/O is described in. The reason for
that is that IDE does not support increasing the logical block size and
at last for now I want to stick to one meachnisms in queue and allow
for easy switching of transports for a given backing image which would
not be possible if scsi and virtio use real 4k sectors, while ide only
uses the physical block exponent.
To make this more common for the different block drivers introduce a
new BlockConf structure holding all common block properties and a
DEFINE_BLOCK_PROPERTIES macro to add them all together, mirroring
what is done for network drivers. Also switch over all block drivers
to use it, except for the floppy driver which has weird driveA/driveB
properties and probably won't require any advanced block options ever.
Example usage for a virtio device with 4k physical block size and
8k optimal I/O size:
-drive file=scratch.img,media=disk,cache=none,id=scratch \
-device virtio-blk-pci,drive=scratch,physical_block_size=4096,opt_io_size=8192
aliguori: updated patch to take into account BLOCK events
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Win32 suffers from a very big memory leak when dealing with SCSI devices.
Each read/write request allocates memory with qemu_memalign (ie
VirtualAlloc) but frees it with qemu_free (ie free).
Pair all qemu_memalign() calls with qemu_vfree() to prevent such leaks.
Signed-off-by: Herve Poussineau <hpoussin@reactos.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a new property named 'ver' to scsi-disk which allows to
specify the version which the virtual disk/cdrom should report to the
guest. By default this is the qemu version (i.e. 0.12). usage:
-drive if=none,id=disk,file=...
-device lsi
-device scsi-disk,drive=disk,bus=scsi.0,unit=0,ver=42
You can also switch the version for all scsi drives using:
-global scsi-disk.ver=42
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
According to the SCSI-2 specification,
http://ldkelley.com/SCSI2/SCSI2/SCSI2/SCSI2-08.html#8.2.5 ,
"if the allocation length of the command descriptor block (CDB) is too
small to transfer all of the parameters, the additional length shall
not be adjusted to reflect the truncation."
The 36 mandatory bytes of response are written to outbuf, and then
only the length requested in CDB is transferred.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Vendor identification, product identification and product revision level
should be padded with spaces without a terminating NULL character, see
SCSI-2 standard, 8.2.5.1 Standard INQUIRY data.
Signed-off-by: Laszlo Ast <laszlo.ast@siemens-enterprise.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Either rename variables and functions to refer to write errors (which is what
they actually do) or introduce a parameter to distinguish reads and writes.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add READ_16 + friends to scsi-defs.h, scsi_command_name() and the
request parsing helper functions.
Use them in scsi-disk.c too.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move VERIFY emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move REPORT_LUNS emulation from scsi_send_command() to
scsi_disk_emulate_command().
Also add REPORT_LUNS to scsi-defs.h and scsi_command_name().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move SERVICE_ACTION_IN emulation from scsi_send_command() to
scsi_disk_emulate_command().
Also add SERVICE_ACTION_IN to scsi-defs.h and scsi_command_name().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move GET_CONFIGURATION emulation from scsi_send_command() to
scsi_disk_emulate_command().
Also add GET_CONFIGURATION to scsi-defs.h and scsi_command_name().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move READ_TOC emulation from scsi_send_command() to
scsi_disk_emulate_command(). Add scsi_disk_emulate_read_toc() function
which holds the longisch READ_TOC emulation code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move SYNCHRONIZE_CACHE emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move READ_CAPACITY emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move ALLOW_MEDIUM_REMOVAL emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move START_STOP emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move MODE_SENSE emulation from scsi_send_command() to
scsi_disk_emulate_command(). Create two helper functions:
mode_sense_page() which writes the actual mode pages and
scsi_disk_emulate_mode_sense() which holds the longish MODE_SENSE
emulation code, calling into mode_sense_page() as needed.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move RESERVE+RELEASE emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move INQUIRY emulation from scsi_send_command() to
scsi_disk_emulate_command(). Also split the longish INQUITY emulation
code into the new scsi_disk_emulate_inquiry() function. Serial number
handling is slightly changed, we don't copy it any more but look it up
directly in DriveInfo which we have at hand anyway.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move REQUEST_SENSE emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add new scsi_disk_emulate_command() function, which will -- when
finished -- handle all scsi disk command emulation except actual I/O
(READ+WRITE commands) which goes to the block layer. The function
builds on top of the new SCSIRequest struct.
SCSI command emulation code is moved over from scsi_send_command() in
steps to ease review and make it easier to pin down regressions (if any)
using bisect. This patch moves over TEST_UNIT_READY only.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Also add and use the scsi_req_complete() helper function for calling the
completion callback.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Bernhard Kohl