The capability register is read-only from guest POV, so we do not need
to update it on reset.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This implements the HPET capability of routing IRQs to the front-side
bus, aka MSI support. This feature can be enabled via the qdev property
"msi" and is off by default.
Note that switching it on can cause guests (at least Linux) to use the
HPET as timer instead of the LAPIC. KVM users should recall that only
the latter is currently available as fast in-kernel model.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
One HPET block supports up to 32 timers. Allow to instantiate more than
the recommended and implemented minimum of 3. The number is configured
via the qdev property "timers". It is also saved/restored so that it
need not match between migration peers.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
By implementing this feature we can also remove a nasty way to kill qemu
(by trying to enable level-triggered hpet interrupts).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Instead of keeping a static reference around, pass the state to
hpet_enabled and hpet_get_ticks. All callers now have it at hand. Will
once allow to instantiate the HPET more than a single time.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Allow the intercept the RTC IRQ for the HPET legacy mode. Then push
routing to IRQ8 completely into the HPET. This allows to turn
hpet_in_legacy_mode() into a private function. Furthermore, this stops
the RTC from clearing IRQ8 even if the HPET is in control.
This patch comes with a side effect: The RTC timers will no longer be
stoppend when there is no IRQ consumer, possibly causing a minor
performance degration. But as the guest may want to redirect the RTC to
the SCI in that mode, it should normally disable unused IRQ source
anyway.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
We have to update the qemu timer when the per-timer enable bit is
toggled, just like for HPET_CFG_ENABLE changes.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Register the HPET as a sysbus device and create it that way. As it can
route its IRQs to any ISA IRQ, we need to connect it to all 24 of them.
Once converted to qdev, we can move reset handler and vmstate
registration into its hands as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Properly initialize HPETTimer::tn and HPETTimer::state once during
hpet_init instead of (re-)writing them on every reset.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Setting the main counter while the HPET is enabled may not be a good
idea of the guest, but it is supported and should, thus, not spam the
host console with warnings.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This moves the private HPET structures into the C module, simplifies
some helper functions and fixes most coding style issues (biggest chunk
was improper switch-case indention). No functional changes.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Also prevent out-of-bounds write access to the timers but don't spam the
host console if it triggers.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
There is absolutely no need to call reset functions when initializing
devices. Since we are already registering them, calling qemu_system_reset()
should suffice. Actually, it is what happens when we reboot the machine,
and using the same process instead of a special case semantics will even
allow us to find bugs easier.
Furthermore, the fact that we initialize things like the cpu quite early,
leads to the need to introduce synchronization stuff like qemu_system_cond.
This patch removes it entirely. All we need to do is call qemu_system_reset()
only when we're already sure the system is up and running
I tested it with qemu (with and without io-thread) and qemu-kvm, and it
seems to be doing okay - although qemu-kvm uses a slightly different patch.
[ v2: user mode still needs cpu_reset, so put it in ifdef. ]
[ v3: leave qemu_system_cond for now. ]
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
In the very least, a change like this requires discussion on the list.
The naming convention is goofy and it causes a massive merge problem. Something
like this _must_ be presented on the list first so people can provide input
and cope with it.
This reverts commit 99a0949b72.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch addresses the problems found by Andriy Gapon:
- The code was incorrectly overwriting the high order 32
bits of the timer and hpet config registers. This didn't show up
in testing because linux and windows use hpet in legacy mode,
where the high order 32 bits (advertising available interrupts)
of the timer config register are ignored, and the high order 32
bits of the hpet config register are reserved and unused.
- The mask for level-triggered interrupts was off by a bit. (hpet
doesn't currently support level-triggered interrupts).
In addition, I removed some unused #defines, and corrected the ioapic
interrupt values advertised. I'd set this up early in hpet development
and never went back to correct it, and no bugs resulted since linux and
windows use hpet in legacy mode where available interrupts are ignored.
Signed-off-by: Beth Kon <eak@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Without this, after system reset, hpet does not detect transition from
non-legacy to legacy mode.
Signed-off-by: Beth Kon <eak@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 8217606e6e (and
updates later added users of qemu_register_reset), we solved the
problem it originally addressed less invasively.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The parameter is always zero except when registering the three internal
io regions (ROM, unassigned, notdirty). Remove the parameter to reduce
the API's power, thus facilitating future change.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add the parameter 'order' to qemu_register_reset and sort callbacks on
registration. On system reset, callbacks with lower order will be
invoked before those with higher order. Update all existing users to the
standard order 0.
Note: At least for x86, the existing users seem to assume that handlers
are called in their registration order. Therefore, the patch preserves
this property. If someone feels bored, (s)he could try to identify this
dependency and express it properly on callback registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
While Intel's spec is not that clear here, latest changes to Linux' HPET
code (commit c23e253e67c9d8a91a0ffa33c1f571a17f0a2403, "x86: hpet: stop
HPET_COUNTER when programming periodic mode") strongly suggest that
HPET_TN_SETVAL rather means: Set _both_ the comparator value and
register.
With this patch applied, I'm again able to boot 2.6.30-rc kernels as
they no longer panic like this (which was due to the comparator
register remaining 0):
ENABLING IO-APIC IRQs
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 2) ...
....... failed.
...trying to set up timer as Virtual Wire IRQ...
..... failed.
...trying to set up timer as ExtINT IRQ...
..... failed :(.
Kernel panic - not syncing: IO-APIC + timer doesn't work! [...]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7168 c046a42c-6fe2-441c-8c8c-71466251a162
I discovered a bug in the hpet code that caused Windows to boot without
hpet. The config mask I was using was preventing the guest from placing
the hpet into 32 bit mode.
(Beth Kon)
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6357 c046a42c-6fe2-441c-8c8c-71466251a162
The attached patch updates the FSF address in the GPL/LGPL boilerplate
in most GPL/LGPLed files, and also in COPYING.LIB.
Signed-off-by: Stuart Brady <stuart.brady@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6162 c046a42c-6fe2-441c-8c8c-71466251a162
This patch adds HPET emulation. It can be disabled with -disable-hpet. An hpet
provides a more finely granular clocksource than otherwise available on PC.
This means that latency-dependent applications (e.g. multimedia) will generally
be smoother when using the HPET.
Signed-off-by: Beth Kon <eak@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6081 c046a42c-6fe2-441c-8c8c-71466251a162
Jan Kiszka