If remsim-bankd connects via 127.0.0.1 or any other loopback-routed IP address to the remsim-server, then the getpername() of remsim-server for the bankd will also render 127.0.0.1, and subsequently that IP address will be provided to remsim-client as address to connect to. In almost all setups, remsim-client will be running on a remote node and hence not able to reach remsim-bankd at 127.0.0.1. Let's turn the server-IP into a mandatory command line argument of remsim-bankd and not use a problematic default value. Change-Id: I3deb05e31cdf35232cf9a118d5a5fcdb5d0ab601
osmo-remsim - Osmocom remote SIM software suite
This software suite is a work in progress.
The client interfaces with GSM phones / modems via dedicated "Card Emulation" devices such as the Osmocom SIMtrace2 or sysmocom sysmoQMOD board + firmware. This hardware implements the ISO7816-3 electrical interface and protocol handling and passes any TPDU headers received from the phone/modem to osmo-remsim-client for further processing of the TPDUs associated to the given APDU transfer.
osmo-remsim-client connects via a RSPRO control connection to osmo-remsim-server at startup and registers itself. It will receive configuration data such as the osmo-remsim-bankd IP+Port and the ClientId from osmo-remsim-server.
After receiving the configuration, osmo-remsim-client will establish a RSPRO data connection to the osmo-remsim-bankd IP:Port.
As the USB interface for remote SIM in simtrace2.git uses one interface per slot, we can implement the client in blocking mode, i.e. use blocking I/O on the TCP/RSPRO side. This simplifies the code compared to a more complex async implementation.
The osmo-remsim-bankd (SIM Bank Daemon) manages one given SIM bank. The initial implementation supports a PC/SC driver to expose any PC/SC compatible card readers as SIM bank.
osmo-remsim-bankd initially connects via a RSPRO control connection to osmo-remsim-server at startup, and will in turn receive a set of initial [client,slot]:[bankd,slot] mappings. These mappings determine which slot on the client (corresponding to a modem) is mapped to which slot on the SIM bank. Mappings can be updated by osmo-remsim-server at any given point in time.
osmo-remsim-bankd implements a RSPRO server, where it listens to connections from osmo-remsim-clients.
As PC/SC only offers a blocking API, there is one thread per PC/SC slot. This thread will perform blocking I/O on the socket towards the client, and blocking API calls on PC/SC.
In terms of thread handling, we do:
- accept() handling in [spare] worker threads ** this means blocking I/O can be used, as each worker thread only has one TCP connection ** client identifies itself with client:slot ** lookup mapping based on client:slot (using mutex for protection) ** open the reader based on the lookup result
The worker threads initially don't have any mapping to a specific reader, and that mapping is only established at a later point after the client has identified itself. The advantage is that the entire bankd can live without any non-blocking I/O.
The main thread handles the connection to osmo-remsim-server, where it can also use non-blocking I/O. However, re-connection would be required, to avoid stalling all banks/cards in the event of a connection loss to the server.
worker threads have the following states:
- INIT (just started)
- ACCEPTING (they're blocking in the accept() call on the server socket fd)
- CONNECTED_WAIT_ID (TCP established, but peer not yet identified itself)
- CONNECTED_CLIENT (TCP established, client has identified itself, no mapping)
- CONNECTED_CLIENT_MAPPED (TCP established, client has identified itself, mapping exists)
- CONNECTED_CLIENT_MAPPED_CARD (TCP established, client identified, mapping exists, card opened)
- CONNECTED_SERVER (TCP established, server has identified itself)
Once the client disconnects, or any other error occurs (such as card I/O errors), the worker thread either returns to INIT state (closing client socket and reader), or it terminates. Termination would mean that the main thread would have to do non-blocking join to detect client termination and then re-spawn clients, so the "return to INIT state" approach seems to make more sense.
- detecting multiple connections from a server, logging this or even avoiding that situation