99 lines
3.6 KiB
Plaintext
99 lines
3.6 KiB
Plaintext
; This file keeps the configuration of cards using the wanpipe driver
|
|
; Each section except for 'general' configures a group (span) of wanpipe channels
|
|
|
|
|
|
[general]
|
|
; This section is used to configure the module and set default values for
|
|
; span parameters
|
|
|
|
; bitswap: boolean: Specify if sent/received data has each byte rotated (swapped)
|
|
; If missing, enable is assumed
|
|
; This parameter can be overridden in group sections
|
|
;bitswap=enable
|
|
|
|
; idlevalue: integer: The value to send for unused voice data channels
|
|
; Interval: 0..255. Default value: 255 (0xFF) for T1, 213 (0xD5) for E1 and BRI
|
|
; A value of -1 sets the circuit code as idle value (for circuit identification)
|
|
; This parameter can be overridden in group sections
|
|
;idlevalue=
|
|
|
|
; buflen: integer: The length of the buffers used by the data sources and consumers
|
|
; Data consumers' buffers will be twice this value
|
|
; This value can't be 0. Defaults to 160
|
|
; This parameter can be overridden in group sections
|
|
;buflen=160
|
|
|
|
; hwrepeatcapable: boolean: Use HW signalling packet repeat capability
|
|
; If disabled, the module will handle packet repeat when requested by the upper layer
|
|
; This parameter can be overridden in group sections
|
|
;hwrepeatcapable=true
|
|
|
|
|
|
;[wanpipe1]
|
|
;The section's name is the card name defined in wanpipe driver
|
|
;E.g. wanpipe1
|
|
|
|
; type: string: Specify the span type
|
|
; Allowed values:
|
|
; E1, T1
|
|
; Defaults to E1
|
|
;type=E1
|
|
|
|
; readonly: boolean: Specifies if this is a read only span (signalling and audio data)
|
|
; If enabled, no data will be sent through this span
|
|
; Defaults to no
|
|
;readonly=no
|
|
|
|
; siggroup: string: The name of the device containing the signalling channel(s)
|
|
; E.g. w1g1
|
|
; This parameter is required when creating a signalling interface (D-channel)
|
|
;siggroup=w1g1
|
|
|
|
; voicegroup: string: The name of the device containing the voice (data) channel(s)
|
|
; This parameter is required when creating a voice group
|
|
; E.g. w1g2
|
|
;voicegroup=w1g2
|
|
|
|
; voicechans: string: The range of channels used for voice (data) transfer
|
|
; Channel intervals may be specified by separating the margins using the '-' character
|
|
; Individual channels or channel intervals may be separated by '.'
|
|
; Duplicate, not strict positive channel numbers, or channel numbers greater then channel
|
|
; count (channel count defaults to 31 for E1 and to 24 for T1) are not allowed
|
|
; E.g. 1-15.17-31 or 1-23 or 1.2.3-15.17.18-30.31
|
|
; If missing, will be computed from type (E1: 1-15.17-31, T1: 1-23)
|
|
;voicechans=1-15.17-31
|
|
|
|
; offset: integer: Positive value to add to each voice channel number
|
|
; Defaults to 0 if missing or invalid
|
|
;offset=
|
|
|
|
; start: integer: Absolute start of circuits numbers, ignore group's start
|
|
; Default is offset + group's current start
|
|
;start=
|
|
|
|
; increment: integer: How much will increment this span the circuit number in
|
|
; the group it belongs to
|
|
; Defaults to 32 for E1, 24 for T1
|
|
;increment=
|
|
|
|
; samples: integer: Specify the number of data samples expected to be received
|
|
; It is used to create the buffer to read data from span. The total buffer will have the
|
|
; number of bytes given by the number of samples multiplied by the number of voice
|
|
; channels configured for this span
|
|
; If missing or 0, it will be computed from type (E1: 50, T1: 64)
|
|
;samples=50
|
|
|
|
; errormask: integer: Value to AND with the received error byte
|
|
; The errors controlled by this mask are 1: RX overrun, 2: CRC, 4: Abort/align
|
|
; Maximum value 255
|
|
; Defaults to 250 (all except overrun and abort) if missing or invalid
|
|
;errormask=250
|
|
|
|
; echocancel: boolean: Enable or disable echo canceller on voice circuits
|
|
; Defaults to no
|
|
;echocancel=no
|
|
|
|
; dtmfdetect: boolean: Enable or disable tone detector on voice circuits
|
|
; Defaults to no
|
|
;dtmfdetect=no
|