99 lines
2.9 KiB
Plaintext
99 lines
2.9 KiB
Plaintext
[general]
|
|
; general SNMP configuration
|
|
|
|
; local address to bind the listener to, default is 0.0.0.0 (all interfaces)
|
|
;addr=0.0.0.0
|
|
|
|
; port on which the module listens for SNMP messages. Defaults to 161.
|
|
;port=161
|
|
|
|
;thread priority for SNMP message processing. Defaults to normal.
|
|
;thread=normal
|
|
|
|
; Version string reported by SNMP, can contain Engine substitutions
|
|
; You may consider adding ${release} or ${revision}
|
|
;version=${version}
|
|
|
|
|
|
[snmp_v2]
|
|
; SNMPv2 configuration
|
|
|
|
; read only access community string. Mandatory.
|
|
ro_community=
|
|
; read write access community string. Mandatory.
|
|
rw_community=
|
|
; read create access community string.
|
|
rc_community=
|
|
|
|
|
|
[snmp_v3]
|
|
; SNMPv3 configuration
|
|
|
|
; format for generating the snmpEngineID
|
|
; values are
|
|
; 1 = IPv4 address format,
|
|
; 2 = IPv6 address format,
|
|
; 3 = MAC address format,
|
|
; 4 = TEXT format,
|
|
; 5 = OCTETS format,
|
|
; 128 = ENTERPRISE specific format
|
|
; Defaults to 4 (TEXT)
|
|
;engine_format=4
|
|
|
|
; information for generating the snmpEngineID.
|
|
; Must correspond to the format set (i.e. if engine_format=1, engine_info must be a IPv4 address)
|
|
; If the format is TEXT (4) the default is the node name
|
|
; NOTE! IPv6 address must not use the IPv6 short format. Mandatory.
|
|
; NOTE! OCTETS format must be a hexified string
|
|
engine_info=
|
|
|
|
|
|
[traps]
|
|
; SNMP traps configuration
|
|
|
|
;enable or disable all_notifications. Defaults to true.
|
|
;enable_traps=true
|
|
|
|
; list traps to disable. Must be separated by ','.
|
|
; An entire substree of traps can be disabled by ending the name of the trap with ".*"
|
|
; (e.g. disable the whole database status traps by adding database.*)
|
|
disable_traps=
|
|
|
|
; IP address to which the traps are sent. Defaults to localhost.
|
|
;remote_ip=localhost
|
|
|
|
; port for the remote IP. Defaults to 162.
|
|
;remote_port=162
|
|
|
|
;SNMP protocol version to use for sending traps (values are SNMPv2c or SNMPv3). Defaults to SNMPv2c.
|
|
;proto_version=SNMPv2c
|
|
|
|
; if SNMPv2 is used, set the community string used for the remote SNMP entity. Mandatory if SNMPv2c traps are used.
|
|
community=
|
|
|
|
; if SNMPv3 is used, specify which configured user should be used for sending traps (there must be a section named like the given value to trap_user)
|
|
; see the example bellow (section [userV3]) for configuring a SNMPv3 user
|
|
; the specified user will not allowed to interrogate this SNMP agent, it will only be used to send traps to the configured traps receiver
|
|
;trap_user=
|
|
|
|
|
|
;[userV3]
|
|
; Configure a section for a SNMPv3 user. The name of the user is the name of the section.
|
|
; To allow SNMPv3 interrogation, at least one SNMPv3 user must be configured
|
|
|
|
; authentication pass phrase. If it is not set, authentication will not be required
|
|
;auth_password=
|
|
|
|
; authentication method ( MD5 | SHA1 ) in case it is used.
|
|
;auth_protocol=MD5
|
|
|
|
; privacy pass phrase. If it is not set, encryption will not be required
|
|
;priv_password=
|
|
|
|
; privacy encryption method ( DES | AES). Default is DES.
|
|
;priv_protocol=DES
|
|
|
|
; user access level. Mandatory. Acceptable values are: readonly, readwrite, readcreate.
|
|
;access=
|
|
|