133 lines
3.5 KiB
Plaintext
133 lines
3.5 KiB
Plaintext
[general]
|
|
; This section sets global variables of the MGCP Gateway module
|
|
|
|
; standby: bool: Enter standby mode initially
|
|
;standby=no
|
|
|
|
; cluster: bool: Enable cluster mode
|
|
; If standby is enabled cluster mode is forced
|
|
;cluster=
|
|
|
|
|
|
[engine]
|
|
; These parameters are used to initialize the MGCP Engine
|
|
|
|
; enabled: bool: Enable the MGCP engine
|
|
;enabled=yes
|
|
|
|
; address: ipaddress: Local IP address to bind to, default all interfaces
|
|
;address=0.0.0.0
|
|
|
|
; port: int: UDP port to bind, set to zero to use default MGCP GW port (2427)
|
|
;port=
|
|
|
|
; Maximum received packet size, 1500 to 65528, default 1500
|
|
;max_recv_packet=1500
|
|
|
|
; buffer: int: Requested size of socket's receive buffer, 0 for system default
|
|
; Minimum value is 4096
|
|
;buffer=0
|
|
|
|
; request_ack: bool: Request an Acknowledge of the transactions
|
|
;request_ack=yes
|
|
|
|
; send_provisional: bool: Send 1xx provisional answers to the requests
|
|
;send_provisional=yes
|
|
|
|
; retrans_interval: int: Message retransmission interval in msec
|
|
;retrans_interval=250
|
|
|
|
; retrans_count: int: Maximum number of retransmissions
|
|
;retrans_count=3
|
|
|
|
|
|
[codecs]
|
|
; This section allows to individually enable or disable the codecs
|
|
|
|
; default: bool: Enable all unlisted codecs by default if a transcoder exists
|
|
;default=enable
|
|
|
|
; mulaw: bool: Companded-only G711 mu-law (PCMU/8000)
|
|
;mulaw=default
|
|
|
|
; alaw: bool: Companded-only G711 a-law (PCMU/8000)
|
|
;alaw=default
|
|
|
|
; gsm: bool: European GSM 06.10 (GSM/8000)
|
|
;gsm=default
|
|
|
|
; lpc10: bool: Linear Prediction Codec (LPC/8000)
|
|
;lpc10=default
|
|
|
|
; ilbc: bool: Internet Low Bandwidth Codec (iLBC/8000)
|
|
;ilbc=default
|
|
|
|
; amr: bool: Adaptive Multi-Rate 3GPP (AMR/8000)
|
|
;amr=default
|
|
|
|
; slin: bool: Signed Linear 16-bit uncompressed (L16/8000)
|
|
;slin=default
|
|
|
|
; g723: bool: ITU G.723 all variations (G723/8000)
|
|
;g723=default
|
|
|
|
; g726: bool: ITU G.726 32-bit (G726-32/8000)
|
|
;g726=default
|
|
|
|
; g728: bool: ITU G.728 all variations (G728/8000)
|
|
;g728=default
|
|
|
|
; g729: bool: ITU G.729 all variations (G729/8000)
|
|
;g729=default
|
|
|
|
; g729_annexb: bool: G.729 Annex B (VAD) support default (if not in SDP)
|
|
; NOTE: RFC 3555 specifies the default should be yes
|
|
;g729_annexb=no
|
|
|
|
; amr_octet: bool: Octet aligned AMR RTP payload default (if not in SDP)
|
|
; NOTE: RFC 4867 (and older 3267) specifies the default is bandwidth efficient
|
|
;amr_octet=no
|
|
|
|
|
|
[hacks]
|
|
; This section holds the dirty stuff required to work with some broken
|
|
; implementations
|
|
;
|
|
; ilbc_forced: string: Format to force as iLBC, can be: ilbc20 or ilbc30
|
|
;ilbc_forced=
|
|
;
|
|
; ilbc_default: string: Format to use for iLBC when packetization is unknown
|
|
;ilbc_default=ilbc30
|
|
|
|
; g729_annexb: bool: Force G.729 Annex B support when parsing the SDP
|
|
;g729_annexb=
|
|
|
|
; ignore_sdp_port: bool: Ignore SDP changes if only the port is different
|
|
; This allows preserving the local RTP session and port
|
|
;ignore_sdp_port=no
|
|
|
|
; ignore_sdp_addr: bool: Ignore SDP changes if only the address is different
|
|
; This allows preserving the local RTP session and port
|
|
;ignore_sdp_addr=no
|
|
|
|
|
|
;[ep PUT_NAME_HERE]
|
|
; One ep ... section is required for each of our endpoints
|
|
; Each endpoint can be associated with at most one Call Agent
|
|
; The endpoint name is a string that can be referenced from other modules
|
|
|
|
; local_user: string: The user part of the local endpoint, default endpoint name
|
|
;local_user=
|
|
|
|
; local_host: string: The host part of the local endpoint, default engine's address
|
|
;local_host=
|
|
|
|
; local_port: int: Declared local port, defaults to engine's port
|
|
;local_port=
|
|
|
|
; remote_host: string: The host part of the remote endpoint, required
|
|
;remote_host=
|
|
|
|
; remote_port: int: Declared remote port, use MGCP default if not set or zero
|
|
;remote_port=
|