101 lines
3.1 KiB
Plaintext
101 lines
3.1 KiB
Plaintext
;[general]
|
|
; max_down: long: The time in seconds after a sctp socket is in connection
|
|
; hanging state. After this time expires the connection is re-established.
|
|
; If the connection is not re established the timer will exponential back off
|
|
; until reaches 60 seconds
|
|
;max_down=10
|
|
|
|
; Each section in this file describes a SIGTRAN connection
|
|
; Connections are referenced from other configurations describing the upper layer
|
|
|
|
;[name-of-connection]
|
|
; The name of the section identifies the connection
|
|
|
|
; type: keyword: Socket type - sctp, tcp, udp, unix
|
|
;type=sctp
|
|
|
|
; stream: bool: Socket connection type.
|
|
; Designed for SCTP sockets to create a stream socket or a sequenced packet socket
|
|
; NOTE: for M2PA if stream is false the M2PA autostart should be on true on both ends,
|
|
; if stream is true the M2PA autostart must be true only at one end
|
|
;stream=true for TCP or UNIX sockets, false for other types
|
|
|
|
; local: string: Primary local address
|
|
; Format is ipv4:port like: 1.1.1.1:3566
|
|
;local=
|
|
|
|
; localN: string: Additional local addresses, SCTP only
|
|
; Multiple addresses can be specified by incrementing the 1-based index at the end of 'local'
|
|
; The address format is ip:port like:
|
|
; local1=1.2.3.4:3566
|
|
; local2=2.3.4.5:3566
|
|
;local1=
|
|
|
|
; remote: string: Primary remote address
|
|
; Format is ipv4:port like: 2.2.2.2:3566
|
|
;remote=
|
|
|
|
; remoteN: string: Additional remote addresses, SCTP only
|
|
; Multiple addresses can be specified by incrementing the 1-based index at the end of 'remote'
|
|
; The address format is ip:port like:
|
|
; remote1=5.6.7.8:3566
|
|
; remote2=6.7.8.9:3566
|
|
;remote1=
|
|
|
|
; endpoint: bool: Set to true if this is an endpoint that actively tries to connect,
|
|
; false to listen for remote connections
|
|
;endpoint=false
|
|
|
|
; linger: int; How much to block waiting for socket to close.
|
|
;linger = 0
|
|
|
|
; listen-notify: boolean: True to notify the upper layer that a new incoming connection has been established
|
|
; Default to true
|
|
;listen-notify=true
|
|
|
|
|
|
; SCTP parameters
|
|
; NOTE these parameters will be set only for SCTP sockets
|
|
; Note! On some platforms this parameters may not be supported
|
|
|
|
; Set initial retransmission interval in milliseconds
|
|
; Ex: rto_initial = 400
|
|
;rto_initial=
|
|
|
|
; Set maximum retransmission interval in milliseconds
|
|
; Ex: rto_max = 800
|
|
;rto_max=
|
|
|
|
; Set minimum retransmission interval in milliseconds
|
|
; Ex: rto_min = 200
|
|
;rto_min=
|
|
|
|
; Set heartbeat interval in milliseconds
|
|
; Ex: hb_interval = 5000
|
|
;hb_interval=
|
|
|
|
; Set maximum number of retransmissions before the SCTP connection is considered down
|
|
; Ex: max_retrans = 5
|
|
;max_retrans=
|
|
|
|
; Enable / disable SCTP heartbeat. Default is enabled
|
|
; Ex: hb_enabled = true
|
|
;hb_enabled=
|
|
|
|
; Set sctp delayed ack parameters
|
|
; Note! Both sack_delay and sack_freq must be present and have values different than 0 to be successfully applied
|
|
|
|
; Set ack time interval for sccp to cumulative acknowledge the received packets
|
|
; Max value 500 in milliseconds
|
|
; Ex: sack_delay = 50
|
|
;sack_delay=
|
|
|
|
; Set the maximum number of unacknowledged packets
|
|
; Ex: sack_freq = 2
|
|
; Note! If you set this to 1 you will disable the sctp acknowledge algorithm
|
|
;sack_freq=
|
|
|
|
; Set sctp socket adaptation parameter
|
|
; E.g. : sctp_adaptation=1
|
|
;sctp_adaptation=
|