75 lines
2.5 KiB
Plaintext
75 lines
2.5 KiB
Plaintext
; IMPORTANT!
|
|
; This feature module is not loaded automatically, it needs a line in yate.conf:
|
|
; [postload]
|
|
; ${modulepath}/sig/isupmangler${modsuffix}=yes
|
|
|
|
|
|
; Each section in this file describe an ISUP interceptor/mangler
|
|
; You can add, remove or disable sections and reload to apply the changes
|
|
|
|
|
|
;[mangler_name]
|
|
; The name of the mangler is reported in the address parameter with the CIC
|
|
|
|
; enable: boolean: Enable the mangler (default)
|
|
;enable=yes
|
|
|
|
; service: int: Service Information Field (protocol number)
|
|
; It is unlikely you will ever need to modify it
|
|
;service=5
|
|
|
|
; netindicator: keyword: Value of Network Indicator bits in the SIO
|
|
; Allowed values: international, spareinternational, national, reservednational
|
|
;netindicator=national
|
|
|
|
; pointcodetype: string: SS7 point code type (required)
|
|
; Can be one of ITU,ANSI,ANSI8,China,Japan,Japan5
|
|
;pointcodetype=
|
|
|
|
; defaultpointcode: string: DPC of the ISUP messages to match
|
|
;defaultpointcode=
|
|
|
|
; remotepointcode: string: OPC of the ISUP messages to match
|
|
;remotepointcode=
|
|
|
|
; symmetric: boolean: Match and mangle messages in the opposite direction too (DPC->OPC)
|
|
; Symmetric should be enabled if intercepting more than just IAM
|
|
;symmetric=no
|
|
|
|
; cic_min: int: Minimum circuit code to match
|
|
;cic_min=1
|
|
|
|
; cic_max: int: Maximum circuit code to match
|
|
;cic_max=16383
|
|
|
|
; intercept: keyword: What class of messages to intercept
|
|
; none: Intercept no message, just mangle routing label and CIC
|
|
; iam: Only intercept IAM
|
|
; cdr: Intercept most CDR related messages: IAM,SAM,ACM,CPG,ANM,CON,SUS,RES,REL,RLC
|
|
; all: Intercept almost all messages, except UPT,UPA,NRM,PAM,CNF,USR
|
|
;intercept=iam
|
|
|
|
; ignore-unknown-digits: boolean: Ignore signal digits that are not ITU standard (A, D and E)
|
|
; The standard set includes only 0-9, B, C and the stop pulsing "."
|
|
; ISUP does not support sending the * and # signals
|
|
;ignore-unknown-digits=yes
|
|
|
|
|
|
; The following set: settings apply to all matched messages, not just those intercepted
|
|
; These mangle the routing label and circuit codes before any other handling
|
|
|
|
; set:opc: int: OPC numeric value to overwrite in message label
|
|
; The special value "mirror" will set the received DPC
|
|
;set:opc=
|
|
|
|
; set:dpc: int: DPC numeric value to overwrite in message label
|
|
; The special value "mirror" will set the received OPC
|
|
;set:dpc=
|
|
|
|
; set:sls: int: Signaling Link Selection to overwrite in message label
|
|
; The special value "cic" will use the circuit code after any altering
|
|
;set:sls=
|
|
|
|
; set:cic: int: Offset to apply to the circuit codes in message body
|
|
;set:cic=0
|