141 lines
2.3 KiB
Plaintext
141 lines
2.3 KiB
Plaintext
WANPIPE ATM Support
|
|
===================
|
|
|
|
|
|
Author: Nenad Corbic <ncorbic@sangoma.com>
|
|
|
|
|
|
|
|
Pre requisites
|
|
--------------
|
|
|
|
1. A Linux kernel source must be available.
|
|
Usually in /usr/src/linux directory.
|
|
|
|
Furthermore, the linux source version must
|
|
match the currently running image.
|
|
|
|
i.e. Output of 'uname -r'
|
|
must match the source version
|
|
number in /usr/src/linux/Makefile.
|
|
|
|
Note: The Setup installation script checks
|
|
for this condition and will take
|
|
appropriate steps to resolve the
|
|
name mismatch.
|
|
|
|
|
|
|
|
|
|
Installing WANPIPE with ATM support
|
|
-----------------------------------
|
|
|
|
The ATM support is installed by default
|
|
during WANPIPE installation process.
|
|
|
|
./Setup install
|
|
|
|
Follow the Setup installation script and choose
|
|
all DEFAULT options.
|
|
|
|
After successful installation proceed to
|
|
configure the card for ATM protocol /usr/sbin/wancfg
|
|
GUI configurator.
|
|
|
|
|
|
Installation Verification
|
|
-------------------------
|
|
|
|
Run wanpipe hardware probe to
|
|
make sure that the kernel modules
|
|
are working fine:
|
|
|
|
Run: wanrouter hwprobe
|
|
|
|
|
|
In case of error:
|
|
-----------------
|
|
|
|
Please contact Sangoma Tech Support
|
|
Tel. 905 474 1990 ex118
|
|
Email: techdesk@sangoma.com
|
|
|
|
|
|
Configuring ATM
|
|
---------------
|
|
|
|
Run: /usr/sbin/wancfg
|
|
|
|
1. Create new device
|
|
|
|
2. Select wanpipe1
|
|
|
|
3. Protocol Section
|
|
Select Protocol: ATM Protocol
|
|
|
|
4. Hardware Section
|
|
Select Probe Hardware
|
|
Select your adapter PRI port.
|
|
|
|
5. Interface Section
|
|
|
|
Select number of PVC you wish to configure
|
|
(Default=1)
|
|
|
|
Specify interface name.
|
|
(Leave it default)
|
|
|
|
Specify ATM VPI, VCI values for that pvc
|
|
|
|
Specify ATM Encapsulation Headers:
|
|
Ethernet over ATM (LLC/VC) (PPPoE)
|
|
Classical IP over ATM (LLC/VC)
|
|
|
|
Specify IP info for pvc
|
|
|
|
6. End of configuration, exit and save
|
|
|
|
|
|
|
|
Start ATM protocol
|
|
------------------
|
|
|
|
Run: wanrouter start
|
|
|
|
|
|
In case of errors:
|
|
------------------
|
|
Run: wanrouter messages
|
|
|
|
It will display kernel error
|
|
messages.
|
|
|
|
Please contact Sangoma Tech Support
|
|
Tel. 905 474 1990 ex118
|
|
Email: techdesk@sangoma.com
|
|
|
|
|
|
Startup Confirmation
|
|
--------------------
|
|
|
|
Run: wanrouter messages
|
|
|
|
Make sure no error messages are dispalyed.
|
|
|
|
Confirm the state of Front End (T1/E1/V35)
|
|
Confirm the Link state
|
|
|
|
Check for any error events.
|
|
|
|
|
|
Further Info
|
|
------------
|
|
|
|
Please contact Sangoma Tech Support
|
|
Tel. 905 474 1990 ex118
|
|
Email: techdesk@sangoma.com
|
|
|
|
|
|
|
|
|