152 lines
3.6 KiB
Plaintext
152 lines
3.6 KiB
Plaintext
;===========================================
|
|
; Global Configuration Section
|
|
;===========================================
|
|
|
|
[settings]
|
|
|
|
;Debug flags is used to enable/disable
|
|
;woomera channel debugging level.
|
|
;Production: set to 2
|
|
;Debugging: set to 3
|
|
;------------------------------
|
|
debug=2
|
|
|
|
|
|
;===========================================
|
|
;Default Profile Configuration Section
|
|
;===========================================
|
|
|
|
[default]
|
|
|
|
;Woomera Server IP Address
|
|
;This is the remote ip address of the
|
|
;Woomera Server (sangoma_mgd: SMG)
|
|
;By default both Asterisk and SMG
|
|
;will reside on same machine.
|
|
;------------------------------
|
|
host=localhost
|
|
|
|
|
|
;Woomera Server TCP/IP Port
|
|
;This is the remote port number of the
|
|
;Woomera Server (sangoma_mgd: SMG)
|
|
;------------------------------
|
|
port=42420
|
|
|
|
|
|
;IP address of remote SMG Audio Server
|
|
;(sangoma_mgd:SMG)
|
|
;By default both Asterisk and SMG
|
|
;will reside on same machine.
|
|
;------------------------------
|
|
audio_ip=127.0.0.1
|
|
|
|
;UDP Media ports used to carry audio.
|
|
;This ports must not conflict with Woomera Server.
|
|
;(eg: sangoma_mgd:SMG)
|
|
;Only change if you have a port conflict with
|
|
;another application.
|
|
;------------------------------
|
|
base_media_port = 20000
|
|
max_media_ports = 5000
|
|
|
|
|
|
;Incoming Context for Woomera Channels
|
|
;All incoming calls will be forwared to defined
|
|
;context in extensions.conf
|
|
;------------------------------
|
|
context=sangoma
|
|
|
|
|
|
;Debug flags is used to enable/disable woomera channel
|
|
;debugging level.
|
|
;Production: set to 2 (Default)
|
|
;Debugging: set to 3
|
|
;------------------------------
|
|
debug=2
|
|
|
|
|
|
;Hard limit for woomera channels
|
|
;Woomera channel driver will only allow defined
|
|
;number of channels. Set this value based on
|
|
;number of T1/E1 channels supported.
|
|
;If unsure set this value to 0.
|
|
;Options: 1 to 600 - limited calls
|
|
; 0 - unlimited Calls (Default)
|
|
;------------------------------
|
|
;max_calls=0
|
|
|
|
|
|
;Enable Incoming DTMF detection
|
|
;This option will enable Rx DTMF detection on each
|
|
;channel. The Tx DTMF is automatically enabled on SMG.
|
|
;If you dont need DTMF do not enable it. Note if SMG
|
|
;supports HWDTMF, this option will automatically be
|
|
;turned off in Asterisk.
|
|
;Options: 1 - Enable DTMF (Default)
|
|
; 0 - Disable DTMF
|
|
;------------------------------
|
|
dtmf_enable=1
|
|
|
|
|
|
;Enable Jitter buffer for this profile
|
|
;This option is tied to the above global
|
|
;jitter buffer options.
|
|
;NOTE: a jb patch must be applied to Asterisk.
|
|
;Options: 1 - Enable JitterBuffer
|
|
; 0 - Disable JitterBuffer (Default)
|
|
;------------------------------
|
|
jb_enable=0
|
|
|
|
|
|
;Enable Asterisk Progress Messaging
|
|
;Used for Asterisk Early Audio with
|
|
;Zap and SIP.
|
|
;Options: 1 - Enable ProgresMsg
|
|
; 0 - Disable ProgresMsg (Default)
|
|
;------------------------------
|
|
progress_enable=0
|
|
|
|
|
|
;Enable progress messages transmissions
|
|
;to TDM on each incoming call after
|
|
;the call has been ACCEPTED. Note
|
|
;this is for INCOMING calls only
|
|
;and should be used when telco
|
|
;requires gateway to send progress messages
|
|
;on EVERY call setup.
|
|
;Options: 1 - Enable progress
|
|
; 0 - Diasble progress (Default)
|
|
;------------------------------
|
|
progress_on_accept=0
|
|
|
|
|
|
;Coding is necessary to identify
|
|
;ulaw/alaw rx/tx gain.
|
|
;Opionts: ulaw
|
|
; alaw
|
|
;Adjust rx and tx gain
|
|
;Options: 0 - Disable
|
|
; 1.0-X.0 - Gain
|
|
;------------------------------
|
|
;coding=ulaw
|
|
;rxgain=0.0
|
|
;txgain=0.0
|
|
|
|
|
|
;Woomera UDP Sequencing
|
|
;This option MUST be also supported
|
|
;by SMG server. Should be used for debugging.
|
|
;Options: 0 - Disable (default)
|
|
; 1 - Enable
|
|
;------------------------------
|
|
;woomera_udp_seq=0
|
|
|
|
|
|
;These options are used to disable rx or tx paths.
|
|
;Should not be used.
|
|
;-------------------------------
|
|
;inbound=no
|
|
;outbound=no
|
|
|