187 lines
6.7 KiB
Plaintext
187 lines
6.7 KiB
Plaintext
|
|
#================================================
|
|
# WANPIPE1 Configuration File
|
|
#================================================
|
|
#
|
|
# Date: Fri Jun 25 16:47:33 EDT 2004
|
|
#
|
|
# Note: This file was generated automatically
|
|
# by /usr/sbin/wancfg program.
|
|
#
|
|
# If you want to edit this file, it is
|
|
# recommended that you use wancfg program
|
|
# to do so.
|
|
#================================================
|
|
# Sangoma Technologies Inc.
|
|
#================================================
|
|
|
|
[devices]
|
|
wanpipe1 = WAN_AFT_TE1, Comment #WAN_AFT_TE1 - Indicates A104/8 card
|
|
#WAN_AFT - Indicates A101/2 card
|
|
|
|
|
|
[interfaces]
|
|
w1g1 = wanpipe1, , STACK, Comment #do not change
|
|
w1lapd = wanpipe1, 1 ,API, lip_lapd, lapd.w1g1, #do not change
|
|
|
|
|
|
[wanpipe1]
|
|
#-------- DEVICE / DRIVER BINDING ----------------------------------
|
|
|
|
CARD_TYPE = AFT #AFT: Same for all aft cards must
|
|
#This value must be hardcoed to AFT for all
|
|
#aft cards.
|
|
|
|
S514CPU = A #Used by A101/2 driver to determine T1/E1 port
|
|
#A - port 1
|
|
#B - port 2
|
|
#For A104 driver: Always set this value to A!
|
|
|
|
CommPort = PRI #Only used by S514 cards.
|
|
#PRI - S514 primary port
|
|
#SEC - S514 secondary port
|
|
#
|
|
#OBSELETE for AFT cards (can be removed)
|
|
|
|
#-------- PCI SETUP ----------------------------------------------
|
|
|
|
|
|
AUTO_PCISLOT = NO #Auto detect PCI/BUS info for this card type
|
|
#NO - disable this option
|
|
#YES- enable this option
|
|
# if enabled bottom two options
|
|
# PCISLOT and PCIBUS will not be used.
|
|
# Therefore one can set the to arbitrary value
|
|
# or remove them all together.
|
|
|
|
PCISLOT = 1 #PCI SLOT Number:
|
|
#Valid values = any number
|
|
|
|
PCIBUS = 2 #PCI BUS Number:
|
|
#Valid values = any number
|
|
|
|
|
|
|
|
#--------------FRONT END SETUP -----------------------------------
|
|
|
|
FE_MEDIA = T1 #Front End Type:
|
|
#T1 - set front end for T1 mode
|
|
#E1 - set front end for E1 mode
|
|
|
|
FE_LCODE = B8ZS #Front End Line Coding
|
|
#If T1: B8ZS or AMI
|
|
# E1: HDB3 or AMI
|
|
|
|
FE_FRAME = ESF #Front End Framing
|
|
#If T1: ESF or D4
|
|
# E1: CRC4 or NCRC4
|
|
|
|
FE_LINE = 1 #Front End Line number.
|
|
#Used by A104 driver to determine T1/E1 port
|
|
#Valid values are: 1-4
|
|
#
|
|
#The A101/2 driver doesn't use this option
|
|
#so one should hardcode it to 1 or
|
|
#remove it all together.
|
|
|
|
|
|
TE_CLOCK = NORMAL #T1/E1 Clock Source
|
|
#NORMAL - slave clock, clock is received from telco
|
|
# This is always the DEFAULT
|
|
#MASTER - master clcok, use hw oscillator clock
|
|
# Only used in back to back mode or
|
|
# when specified by telco.
|
|
|
|
TE_REF_CLOCK = 0 #T1/E1 Reference Clock Source
|
|
#This option allows one to use the incoming clock
|
|
#from a different port as a clock source to this
|
|
#port. FOR THIS OPTION TO WORK: TE_CLOCK=MASTER
|
|
#Valid options: 0 - disable
|
|
# 1-4 - use clock from particular port
|
|
|
|
ACTIVE_CH = ALL #Specify T1/E1 Active channels (timeslots)
|
|
#Since AFT cards support channelization this
|
|
#option MUST BE HARDCODED TO: ALL!
|
|
|
|
TE_HIGHIMPEDANCE = NO #Set the Front Ent chip in High Impedance mode
|
|
#used for datascoping:
|
|
#NO - Disable high impedance mode (DEFAULT)
|
|
#YES - Enable hight impedance mode
|
|
# (only if you know what you are doing)
|
|
|
|
LBO = 0DB #Front End Line Buildout
|
|
# 0db (Default)
|
|
# 7.5dB
|
|
# 15dB
|
|
# 22.5dB
|
|
# 0-110ft
|
|
# 110-220ft
|
|
# 220-330ft
|
|
# 330-440ft
|
|
# 440-550ft
|
|
# 550-660ft
|
|
|
|
FE_TXTRISTATE = NO #Front End Tri-State Mode
|
|
#Disable front end chip TX mode
|
|
#Used for datascoping or connecting multiple ports
|
|
#together where one port is operating normally and others
|
|
#are tristated, thus only receiving.
|
|
#NO - Disable tristae mode
|
|
#YES- Enable tristate mode
|
|
|
|
MTU = 1500 #Global MTU Value
|
|
#Note: This value is overwritten by the
|
|
# interface MTU value below if it exists.
|
|
#Values: any number [ suggested 128 - 4086 ]
|
|
|
|
|
|
UDPPORT = 9000 #OBSELETE option
|
|
#Old wanpipemon used sockets to connect to
|
|
#device driver.
|
|
|
|
TTL = 255 #OBSELETE option
|
|
#Old wanpipemon used sockets to connect to
|
|
#device driver.
|
|
|
|
IGNORE_FRONT_END = NO #Ignore Fronte End State
|
|
#NO - Do not ignore front end state,
|
|
# therefore if state changes, change the
|
|
# state of the above protocol.
|
|
#YES- Igonore front end state
|
|
# Thus if front end goes down, the protocol
|
|
# will not know.
|
|
|
|
|
|
#--------------------------------------------
|
|
#Q921/LAPD Profile Configuration
|
|
#--------------------------------------------
|
|
|
|
[lapd.w1g1]
|
|
LAP_STATION = DTE
|
|
T1 = 2
|
|
T2 = 0
|
|
T3 = 6
|
|
T4 = 3
|
|
N2 = 5
|
|
LAP_MODE = 128
|
|
LAP_WINDOW = 7
|
|
MAX_PKT_SIZE = 1024
|
|
|
|
|
|
|
|
#--------------------------------------------
|
|
#Hardware Interface Configuration
|
|
#--------------------------------------------
|
|
|
|
|
|
[w1g1]
|
|
HDLC_STREAMING = YES #Enable hardware hdlc engine
|
|
#(Do not change)
|
|
|
|
ACTIVE_CH = 24 #DCHAN on T1/E1 Span
|
|
#For T1 select 24
|
|
#For E1 seelct 16
|
|
#(Confirm with telco)
|
|
|
|
[w1lapd]
|