121 lines
3.7 KiB
Plaintext
121 lines
3.7 KiB
Plaintext
# ============================================================================
|
|
# WAN Router Configuration File.
|
|
# ============================================================================
|
|
# Protocol: Cisco HDLC (CHDLC): PRIMARY Port Configuration
|
|
# ----------------------------------------------------------------------------
|
|
|
|
|
|
[devices]
|
|
wanpipe1 = WAN_MULTPPP, Cisco HDLC
|
|
|
|
|
|
[interfaces]
|
|
|
|
wp1_chdlc = wanpipe1, ,API, PRI port connection (high speed 2Mbps)
|
|
|
|
|
|
[wanpipe1]
|
|
|
|
CARD_TYPE = S51X
|
|
S514CPU = A # S514 PCI Card CPU: A or B (s514 only)
|
|
AUTO_PCISLOT = YES # Autodetect pci slot (s514 only)
|
|
PCISLOT = 5
|
|
PCIBUS = 0
|
|
|
|
CommPort = SEC # PRI: High speed (2 MBps) primary port
|
|
# SEC: Low speed (512 MBps) secondary port
|
|
#
|
|
|
|
Firmware = /etc/wanpipe/firmware/cdual514asy.sfm # adapter firmware
|
|
|
|
#
|
|
# ----- Physical interface configuration -----
|
|
Interface = RS232 # physical interface type, RS232/V35
|
|
Clocking = Internal # Tx/Rx clock source, External/Internal
|
|
#
|
|
# * Jumpers must be set for internal or external
|
|
# clocking for:
|
|
# s508 : RS232 SEC port
|
|
# s514 : RS232 PRI and SEC port
|
|
#
|
|
#
|
|
BaudRate = 19200 # data transfer rate in bps, 1200..2048000
|
|
# Note: Max 256KBps for RS232 interface !!!
|
|
#
|
|
|
|
Receive_only = NO #
|
|
|
|
|
|
# ----- Media-specific configuration ---------
|
|
MTU = 1500 # maximum data transfer unit, bytes
|
|
TTL = 0x7F # Time To Live parameter for UDP packets
|
|
UDPPORT = 9000 # UDP Port, used by cpipemon debugger
|
|
|
|
|
|
|
|
[wp1_chdlc]
|
|
|
|
# --------- Link Management parameters ---------
|
|
MULTICAST = NO # Enable Multicasting
|
|
#
|
|
IGNORE_DCD = NO # Ignore DCD when determining active link status
|
|
# (YES/NO) Default: NO (ONLY USED FOR TESTING)
|
|
#
|
|
IGNORE_CTS = NO # Ignore CTS when determining active link status
|
|
# (YES/NO) Default: NO (ONLY USED FOR TESTING)
|
|
#
|
|
IGNORE_KEEPALIVE= NO # Ignore Keep alives when determining active
|
|
# link status (YES/NO) Default: NO
|
|
# (ONLY USED FOR TESTING)
|
|
#
|
|
HDLC_STREAMING = YES # Options YES or NO
|
|
# YES: Turns OFF cisco hdlc protocol
|
|
# and uses raw frames, and no polling.
|
|
# NO: Turns ON the cisco hdlc protocol
|
|
#
|
|
KEEPALIVE_TX_TIMER = 10000 # Interval between Keep Alive (0-60000 ms)
|
|
# Default 10000ms
|
|
#
|
|
KEEPALIVE_RX_TIMER = 11000 # Interval to expect Keepalives (10-60000 ms)
|
|
# Default 10000ms
|
|
#
|
|
KEEPALIVE_ERR_MARGIN = 5 # Consecutive keepalive timeouts before bringing
|
|
# down the link. Default 3, range: 1 - 20
|
|
#
|
|
SLARP_TIMER = 0 # Used for DYNAMIC/STATIC IP addressing
|
|
#
|
|
# 0 : Static IP addressing.
|
|
# IP addresses are obtained from
|
|
# the interface file:
|
|
# (usr/lib/wanrouter/interfaces/wp1_chdlc)
|
|
#
|
|
# Non Zero : Dynamic IP addressing.
|
|
# IP addresses are requested from
|
|
# the remote station.
|
|
# Valid values are from 1-6000(ms)
|
|
# Default: 5000
|
|
# Note: A dummy interface file
|
|
# is still required !!!
|
|
|
|
|
|
ASYNC_MODE = YES # Enables Async mode
|
|
ASY_DATA_TRANSPARENT = NO
|
|
RTS_HS_FOR_RECEIVE = NO
|
|
XON_XOFF_HS_FOR_RECEIVE = NO
|
|
XON_XOFF_HS_FOR_TRANSMIT = NO
|
|
DCD_HS_FOR_TRANSMIT = NO
|
|
CTS_HS_FOR_TRANSMIT = NO
|
|
TX_BITS_PER_CHAR = 8
|
|
RX_BITS_PER_CHAR = 8
|
|
STOP_BITS = ONE
|
|
PARITY = NONE
|
|
BREAK_TIMER = 50
|
|
INTER_CHAR_TIMER = 123
|
|
RX_COMPLETE_LENGTH = 20
|
|
XON_CHAR = 0xFE
|
|
XOFF_CHAR = 0xFF
|
|
|
|
|
|
|
|
#--------------------- END OF WANPIPE CONFIGURATION ------------------------
|