290 lines
10 KiB
Plaintext
290 lines
10 KiB
Plaintext
#================================================
|
|
# WANPIPE1 Configuration File
|
|
#================================================
|
|
#
|
|
# Date: Tue Aug 30 13:40:34 EDT 2005
|
|
#
|
|
# Note: This file was generated automatically
|
|
# by /usr/sbin/wancfg program.
|
|
#
|
|
# If you want to edit this file, it is
|
|
# recommended that you use wancfg program
|
|
# to do so.
|
|
#================================================
|
|
# Sangoma Technologies Inc.
|
|
#================================================
|
|
|
|
[devices]
|
|
wanpipe1 = WAN_AFT_TE1, Comment #WAN_AFT_TE1 - Indicates A104/8 card
|
|
#WAN_AFT - Indicates A101/2 card
|
|
|
|
[interfaces]
|
|
w1g1 = wanpipe1, , STACK, Comment
|
|
#Hardware Interface
|
|
#
|
|
#w1g1 - if name
|
|
#
|
|
#wanpipe1 - device name must be same as above
|
|
#
|
|
#<empty field> - not used
|
|
#
|
|
#STACK - opertaion mode indicating that
|
|
# protocol stack is running over
|
|
# this interface
|
|
|
|
w1g1fr = wanpipe1, auto, WANPIPE, fr, w1g1.fr
|
|
#Frame Relay Protocol Interace
|
|
#
|
|
#w1g1fr - if name
|
|
#
|
|
#wanpipe1 - hardware device name
|
|
# must be same as above
|
|
#
|
|
#dlci_num - auto - auto dlci (CPE ONLY)
|
|
# 16-1007 - actual dlci number
|
|
# (Note this filed is not used
|
|
# for PPP or CHDLC protocols)
|
|
#
|
|
#OP mode: - WANPIPE - operation mode IP
|
|
# A file with IP addresses must exist
|
|
# for this interface in:
|
|
# /etc/wanpipe/interfaces/w1g1fr
|
|
# - API - opertaion mode API
|
|
# No IP address info needed
|
|
# Interface will be brought up with no IP.
|
|
# One can connect a AF_WANPIPE socket to this
|
|
# interface.
|
|
#protocol - Interface protocol
|
|
# [fr, ppp, chdlc]
|
|
#
|
|
#protocol profile - Protocol configuration profile
|
|
# Multiple protocols instances can have
|
|
# same protocol profile.
|
|
|
|
[wanpipe1]
|
|
|
|
#-------- DEVICE / DRIVER BINDING ----------------------------------
|
|
|
|
CARD_TYPE = AFT #AFT: Same for all aft cards must
|
|
#This value must be hardcoed to AFT for all
|
|
#aft cards.
|
|
|
|
S514CPU = A #Used by A101/2 driver to determine T1/E1 port
|
|
#A - port 1
|
|
#B - port 2
|
|
#For A104 driver: Always set this value to A!
|
|
|
|
CommPort = PRI #Only used by S514 cards.
|
|
#PRI - S514 primary port
|
|
#SEC - S514 secondary port
|
|
#
|
|
#OBSELETE for AFT cards (can be removed)
|
|
|
|
#-------- PCI SETUP ----------------------------------------------
|
|
|
|
|
|
AUTO_PCISLOT = NO #Auto detect PCI/BUS info for this card type
|
|
#NO - disable this option
|
|
#YES- enable this option
|
|
# if enabled bottom two options
|
|
# PCISLOT and PCIBUS will not be used.
|
|
# Therefore one can set the to arbitrary value
|
|
# or remove them all together.
|
|
|
|
PCISLOT = 2 #PCI SLOT Number:
|
|
#Valid values = any number
|
|
|
|
PCIBUS = 2 #PCI BUS Number:
|
|
#Valid values = any number
|
|
|
|
|
|
#--------------FRONT END SETUP -----------------------------------
|
|
|
|
FE_MEDIA = T1 #Front End Type:
|
|
#T1 - set front end for T1 mode
|
|
#E1 - set front end for E1 mode
|
|
|
|
FE_LCODE = B8ZS #Front End Line Coding
|
|
#If T1: B8ZS or AMI
|
|
# E1: HDB3 or AMI
|
|
|
|
FE_FRAME = ESF #Front End Framing
|
|
#If T1: ESF or D4
|
|
# E1: CRC4 or NCRC4
|
|
|
|
FE_LINE = 1 #Front End Line number.
|
|
#Used by A104 driver to determine T1/E1 port
|
|
#Valid values are: 1-4
|
|
#
|
|
#The A101/2 driver doesn't use this option
|
|
#so one should hardcode it to 1 or
|
|
#remove it all together.
|
|
|
|
|
|
TE_CLOCK = NORMAL #T1/E1 Clock Source
|
|
#NORMAL - slave clock, clock is received from telco
|
|
# This is always the DEFAULT
|
|
#MASTER - master clcok, use hw oscillator clock
|
|
# Only used in back to back mode or
|
|
# when specified by telco.
|
|
|
|
TE_REF_CLOCK = 0 #T1/E1 Reference Clock Source
|
|
#This option allows one to use the incoming clock
|
|
#from a different port as a clock source to this
|
|
#port. FOR THIS OPTION TO WORK: TE_CLOCK=MASTER
|
|
#Valid options: 0 - disable
|
|
# 1-4 - use clock from particular port
|
|
|
|
ACTIVE_CH = ALL #Specify T1/E1 Active channels (timeslots)
|
|
#Since AFT cards support channelization this
|
|
#option MUST BE HARDCODED TO: ALL!
|
|
|
|
TE_HIGHIMPEDANCE = NO #Set the Front Ent chip in High Impedance mode
|
|
#used for datascoping:
|
|
#NO - Disable high impedance mode (DEFAULT)
|
|
#YES - Enable hight impedance mode
|
|
# (only if you know what you are doing)
|
|
|
|
LBO = 0DB #Front End Line Buildout
|
|
# 0db (Default)
|
|
# 7.5dB
|
|
# 15dB
|
|
# 22.5dB
|
|
# 0-110ft
|
|
# 110-220ft
|
|
# 220-330ft
|
|
# 330-440ft
|
|
# 440-550ft
|
|
# 550-660ft
|
|
|
|
FE_TXTRISTATE = NO #Front End Tri-State Mode
|
|
#Disable front end chip TX mode
|
|
#Used for datascoping or connecting multiple ports
|
|
#together where one port is operating normally and others
|
|
#are tristated, thus only receiving.
|
|
#NO - Disable tristae mode
|
|
#YES- Enable tristate mode
|
|
|
|
MTU = 1500 #Global MTU Value
|
|
#Note: This value is overwritten by the
|
|
# interface MTU value below if it exists.
|
|
#Values: any number [ suggested 128 - 4086 ]
|
|
|
|
UDPPORT = 9000 #OBSELETE option
|
|
#Old wanpipemon used sockets to connect to
|
|
#device driver.
|
|
|
|
TTL = 255 #OBSELETE option
|
|
#Old wanpipemon used sockets to connect to
|
|
#device driver.
|
|
|
|
IGNORE_FRONT_END = NO #Ignore Fronte End State
|
|
#NO - Do not ignore front end state,
|
|
# therefore if state changes, change the
|
|
# state of the above protocol.
|
|
#YES- Igonore front end state
|
|
# Thus if front end goes down, the protocol
|
|
# will not know.
|
|
|
|
#--------------------------------------------
|
|
#Protocol Interface Configuration
|
|
#--------------------------------------------
|
|
|
|
[w1g1fr]
|
|
|
|
CIR = 0 #OBSOLETE: Not used by AFT cards
|
|
BC = 0 #OBSOLETE: Not used by AFT cards
|
|
BE = 0 #OBSOLETE: Not used by AFT cards
|
|
INARP = NO #OBSOLETE: Not used by AFT cards
|
|
INARPINTERVAL = 0 #OBSOLETE: Not used by AFT cards
|
|
INARP_RX = NO #OBSOLETE: Not used by AFT cards
|
|
IPX = NO #OBSOLETE: Not used by AFT cards
|
|
|
|
MULTICAST = NO #Enable/Disable MULTICAST flag on this interface
|
|
#NO - Disable
|
|
#YES- Enable
|
|
|
|
DYN_INTR_CFG = NO #Enable Dynamic IP addressing if supported by
|
|
#protocol.
|
|
#NO - Disable Dynamic IP addressing
|
|
#YES- Eanble Dynamic IP addressing
|
|
|
|
TRUE_ENCODING_TYPE = NO #OBSOLETE: Not used by AFT cards
|
|
|
|
GATEWAY = NO #Indicates that this interface is a default
|
|
#gateway interface. Used by dynamic IP code.
|
|
#NO - This interface is not gateway
|
|
#YES- This interface is a gateway
|
|
|
|
LIP_MTU = 1500 #OPTIONAL
|
|
#MTU for LIP Interface
|
|
#Values: 128 to 4096
|
|
#Note! This value should not be greater
|
|
# Than MTU for lower interfaces
|
|
#If not defined: default 1500
|
|
|
|
#--------------------------------------------
|
|
#Protocol Profile Configuration
|
|
#--------------------------------------------
|
|
|
|
|
|
[w1g1.fr]
|
|
NUMBER_OF_DLCI = 1 #Number of DLCI's
|
|
#Important when configured for NODE!
|
|
|
|
Station = CPE #Station Configuration
|
|
#CPE - customer end point
|
|
#NODE - frame relay switch emulation.
|
|
|
|
SIGNALLING = AUTO #Frame Relay Signalling
|
|
#AUTO - Tries to autodetect frame relay
|
|
# signalling (CPE mode only)
|
|
#ANSI
|
|
#LMI
|
|
#Q933
|
|
|
|
T391 = 10
|
|
|
|
T392 = 16
|
|
|
|
N391 = 6
|
|
|
|
N392 = 6
|
|
|
|
N393 = 4
|
|
|
|
FR_ISSUE_FS = YES #OBSOLETE Not used by AFT cards
|
|
|
|
|
|
#-------------------------------------------
|
|
#Hardware Interface Configuration
|
|
#-------------------------------------------
|
|
|
|
[w1g1]
|
|
HDLC_STREAMING = YES #Enable HDLC engine on this interface
|
|
#YES - HDLC engine enabled.
|
|
# All frames Rx/Tx from/to this interface
|
|
# will be in HDLC format.
|
|
#NO - HDLC engine disabled.
|
|
# Rx/Tx Transparent (Raw) bits to and from
|
|
# interface.
|
|
|
|
ACTIVE_CH = ALL #Timeslot binding
|
|
#Specify what T1/E1 timeslots should be boudned
|
|
#to this interface.
|
|
#ALL - All timeslots
|
|
#1-5 - 1 to 5
|
|
#1.5 - 1 and 5
|
|
#1-10.11-20 - 1 to 10 and 11 to 20
|
|
|
|
MTU = 1500 #OPTIONAL
|
|
#Maximum Tx Size for this interface
|
|
#if this value is NOT set the global
|
|
#MTU value will be used
|
|
|
|
MRU = 1500 #OPTIONAL
|
|
#Maximum Rx Size for this interface
|
|
#if this value is NOT set the global
|
|
#MRU value will be used
|
|
|