180 lines
3.4 KiB
Plaintext
180 lines
3.4 KiB
Plaintext
WANPIPE T1/E1/V35 Frame Relay
|
|
==============================
|
|
|
|
|
|
Author: Nenad Corbic <ncorbic@sangoma.com>
|
|
|
|
|
|
|
|
Pre requisites
|
|
--------------
|
|
|
|
1. A Linux kernel source must be available.
|
|
Usually in /usr/src/linux directory.
|
|
|
|
Furthermore, the linux source version must
|
|
match the currently running image.
|
|
|
|
i.e. Output of 'uname -r'
|
|
must match the source version
|
|
number in /usr/src/linux/Makefile.
|
|
|
|
Note: The Setup installation script checks
|
|
for this condition and will take
|
|
appropriate steps to resolve the
|
|
name mismatch.
|
|
|
|
|
|
|
|
|
|
Installing WANPIPE with Frame Relay support
|
|
--------------------------------------------
|
|
|
|
The Frame Relay support is installed by default
|
|
during WANPIPE installation process.
|
|
|
|
./Setup install
|
|
|
|
After successful installation proceed to
|
|
configure the card for Frame Relay Protocol
|
|
/usr/sbin/wancfg GUI configurator.
|
|
|
|
|
|
Installation Verification
|
|
-------------------------
|
|
|
|
Run wanpipe hardware probe to
|
|
make sure that the kernel modules
|
|
are working fine:
|
|
|
|
Run: wanrouter hwprobe
|
|
|
|
|
|
In case of error:
|
|
-----------------
|
|
|
|
Please contact Sangoma Tech Support
|
|
Tel. 905 474 1990 ex118
|
|
Email: techdesk@sangoma.com
|
|
|
|
|
|
Configuring Frame Relay
|
|
------------------------
|
|
|
|
NOTE: Wanpipe drivers support two versions
|
|
of frame relay:
|
|
|
|
|
|
o FRAME REALAY
|
|
Original frame relay that runs
|
|
on the card and is supported
|
|
on a single PRIMARY port.
|
|
|
|
o MULTIPORT FRAME RELAY
|
|
Kernel based frame relay that
|
|
can run over both PRIMARY and
|
|
SECONDARY ports.
|
|
|
|
|
|
|
|
Run: /usr/sbin/wancfg
|
|
|
|
1. Create new device
|
|
|
|
2. Select wanpipe1
|
|
|
|
3. Protocol Section
|
|
Select Protocol: Frame Relay Protocol OR
|
|
MultiPort Frame Relay
|
|
|
|
4. Hardware Section
|
|
Select Probe Hardware
|
|
|
|
Frame Relay Protocol
|
|
Select your adapter PRI port.
|
|
|
|
MultiPort Frame Relay
|
|
Select your adapter for PRI or SEC
|
|
port.
|
|
|
|
|
|
5. Interface Section
|
|
|
|
Select number of interfaces/DLCI's you wish to configure
|
|
(Default=1)
|
|
|
|
For each network interface/DLCI do the following:
|
|
|
|
Specify interface name.
|
|
(Leave it default)
|
|
|
|
Operation Mode:
|
|
|
|
WANPIPE used to run IP protocols
|
|
on top of frame relay.
|
|
|
|
BRIDGE used to run Bridge/Ethernet over Frame Relay
|
|
The interface will have no IP addresses
|
|
since it should be bound into the
|
|
Ethernet bridge.
|
|
|
|
BRIDGE NODE
|
|
used to run IP/Ethernet over Frame Relay.
|
|
THe interface will have IP addresses.
|
|
|
|
API used to develop custom applications
|
|
on top of frame relay
|
|
|
|
|
|
Ignore Modem Status:
|
|
(Only available in WANPIPE operation mode)
|
|
|
|
Option used to monitor the front end T1/E1
|
|
status. If the front end looses sync the
|
|
link will be declared down.
|
|
|
|
NO: Run front end monitoring (default)
|
|
YES: Ignore front end state.
|
|
|
|
|
|
IP Setup:
|
|
(Only available in WANPIPE operation mode)
|
|
|
|
Specify IP info for network interface
|
|
|
|
6. End of configuration, exit and save
|
|
|
|
|
|
|
|
Start Frame Relay Protocol
|
|
----------------------------
|
|
|
|
Run: wanrouter start
|
|
|
|
|
|
In case of errors:
|
|
------------------
|
|
Run: wanrouter messages
|
|
|
|
It will display kernel error
|
|
messages.
|
|
|
|
Please contact Sangoma Tech Support
|
|
Tel. 905 474 1990 ex118
|
|
Email: techdesk@sangoma.com
|
|
|
|
|
|
Startup Confirmation
|
|
--------------------
|
|
|
|
Run: wanrouter messages
|
|
|
|
Make sure no error messages are dispalyed.
|
|
|
|
Confirm the state of Front End (T1/E1/V35)
|
|
Confirm the Link state
|
|
|
|
Check for any error events.
|
|
|
|
|