#================================================
# WANPIPE4 Configuration File
#================================================
#
# Date: Fri Jul 30 16:47:33 EDT 2004
#
# Note: This file was generated automatically
#       by /usr/sbin/wancfg program.
#
#       If you want to edit this file, it is
#       recommended that you use wancfg program
#       to do so.
#================================================
# Sangoma Technologies Inc.
#================================================

[devices]
wanpipe1 = WAN_AFT_SERIAL, Comment

#===================================================
#Hardware Interface Definition
#Protocol Interface Definition
#===================================================

[interfaces]

#Hardware interface w1g1 used in STACK mode
w1g1 = wanpipe1, , STACK, Comment

#Protocol interface w4sa1 
#w4sa1 	-> ifname
#wanpipe1 	-> devname
#33 	 	-> sdlc address (in decimal)
#API		-> API operation mode
#lip_xdlc	-> XDLC protocol
#xdlc.w1g1	-> XDLC protocol cfg profile

w4sa1 = wanpipe1, 33 , API, lip_xdlc, xdlc.w1g1,   



#===================================================
#Hardware Device Configuration
#===================================================

[wanpipe1]

CARD_TYPE 	= AFT			#AFT card type - no other options

S514CPU 	= A			#A - no other options

AUTO_PCISLOT	= NO			#Autodetec a single AFT card 	
					#in the system:  YES | NO

PCISLOT 	= 2			#PCI Slot info
PCIBUS		= 7			#PCI Bus info
					#Use wanrouter hwprobe to determine this info

FE_LINE		= 1			#A144 Serial Port
					#Valid Values: 1 | 2 | 3 | 4

Clocking 	= External		#External | Internal

BaudRate 	= 2400			#Integer from 128 to 1500000
					#Only valid with Internal Clocking

IGNORE_FRONT_END  = NO			#Ignore CTS/RTS states
					#Optoins: YES | NO

MTU		= 1500			#Hardware HDLC MTU
					#Valid:  128 to 8000
					#Default: 1500

#===================================================
#SDLC Profile Configuraton
#Used above interface devices
#===================================================

[xdlc.w1g1]

STATION 		= SECONDARY	#PRIMARY/SECONDARY
MAX_I_FIELD_LEN		= 1024			
WINDOW			= 7

#-------------------------------------------------
#Primary Only Config
#-------------------------------------------------

PROT_CONFIG		= TWO_WAY_ALTERNATE #TWO_WAY_ALTERNATE or
				    	    #TWO_WAY_SIMULTANEOUS

TWS_MAX_ACK_CNT		= 10	#Used in TWO_WAY_SIMULTANEOUS mode:
				# Number of packets to ack in full 
				# duplex mode number must be greater 
				# than window.
	
	
ERROR_RESP_CONFIG 	= PRI_SNRM_ON_NO_RESP	#PRI_SNRM_ON_NO_RESP or
						# PRI_DISC_ON_NO_RESP
  						#Response after no response 
						#timeout
						
PRI_NORMAL_POLL_TIMER		= 40		#Normal Primary Poll in (ms)
PRI_SLOW_POLL_TIMER		= 80		#Slow (disc) Pri Poll (ms)

PRI_FRAME_RESPONSE_TIMER	= 1000		#Timeout if packet with F 
						#bit is not received (ms).
MAX_NO_RESPONSE_CNT		= 5		#Error after number of above 
						#timeouts.


#--------------------------------------------------
#Primary and Secondary Config
#--------------------------------------------------

MAX_FRAME_RETRANSMIT_CNT	= 7		#Number of consec REJ 
						#before error
MAX_RNR_CNT			= 7		#Number of consec RNR 
						#before error 

#--------------------------------------------------
#Secondary only Config
#--------------------------------------------------

SEC_NRM_TIMER			= 2000		#Period between pri polls (ms)


#===================================================
#Protocol Interface Configuration
#===================================================

[w4sa1]

#No options




#===================================================
#Hardware Interface Configuration
#===================================================
[w1g1]

HDLC_STREAMING	= YES		#Enable hardware HDLC engine
				#Options: YES - hdlc enabled
				#         NO - bitstreaming mode

ACTIVE_CH	= 1		#Single serial channel - no other options