#================================================ # WANPIPE1 Configuration File #================================================ # # Date: Tue Aug 30 13:40:34 EDT 2005 # # Note: This file was generated automatically # by /usr/sbin/wancfg program. # # If you want to edit this file, it is # recommended that you use wancfg program # to do so. #================================================ # Sangoma Technologies Inc. #================================================ [devices] wanpipe1 = WAN_AFT_TE1, Comment #WAN_AFT_TE1 - Indicates A104/8 card #WAN_AFT - Indicates A101/2 card [interfaces] w1g1 = wanpipe1, , STACK, Comment #Hardware Interface # #w1g1 - if name # #wanpipe1 - device name must be same as above # # - not used # #STACK - opertaion mode indicating that # protocol stack is running over # this interface w1g1fr = wanpipe1, auto, WANPIPE, fr, w1g1.fr #Frame Relay Protocol Interace # #w1g1fr - if name # #wanpipe1 - hardware device name # must be same as above # #dlci_num - auto - auto dlci (CPE ONLY) # 16-1007 - actual dlci number # (Note this filed is not used # for PPP or CHDLC protocols) # #OP mode: - WANPIPE - operation mode IP # A file with IP addresses must exist # for this interface in: # /etc/wanpipe/interfaces/w1g1fr # - API - opertaion mode API # No IP address info needed # Interface will be brought up with no IP. # One can connect a AF_WANPIPE socket to this # interface. #protocol - Interface protocol # [fr, ppp, chdlc] # #protocol profile - Protocol configuration profile # Multiple protocols instances can have # same protocol profile. [wanpipe1] #-------- DEVICE / DRIVER BINDING ---------------------------------- CARD_TYPE = AFT #AFT: Same for all aft cards must #This value must be hardcoed to AFT for all #aft cards. S514CPU = A #Used by A101/2 driver to determine T1/E1 port #A - port 1 #B - port 2 #For A104 driver: Always set this value to A! CommPort = PRI #Only used by S514 cards. #PRI - S514 primary port #SEC - S514 secondary port # #OBSELETE for AFT cards (can be removed) #-------- PCI SETUP ---------------------------------------------- AUTO_PCISLOT = NO #Auto detect PCI/BUS info for this card type #NO - disable this option #YES- enable this option # if enabled bottom two options # PCISLOT and PCIBUS will not be used. # Therefore one can set the to arbitrary value # or remove them all together. PCISLOT = 2 #PCI SLOT Number: #Valid values = any number PCIBUS = 2 #PCI BUS Number: #Valid values = any number #--------------FRONT END SETUP ----------------------------------- FE_MEDIA = T1 #Front End Type: #T1 - set front end for T1 mode #E1 - set front end for E1 mode FE_LCODE = B8ZS #Front End Line Coding #If T1: B8ZS or AMI # E1: HDB3 or AMI FE_FRAME = ESF #Front End Framing #If T1: ESF or D4 # E1: CRC4 or NCRC4 FE_LINE = 1 #Front End Line number. #Used by A104 driver to determine T1/E1 port #Valid values are: 1-4 # #The A101/2 driver doesn't use this option #so one should hardcode it to 1 or #remove it all together. TE_CLOCK = NORMAL #T1/E1 Clock Source #NORMAL - slave clock, clock is received from telco # This is always the DEFAULT #MASTER - master clcok, use hw oscillator clock # Only used in back to back mode or # when specified by telco. TE_REF_CLOCK = 0 #T1/E1 Reference Clock Source #This option allows one to use the incoming clock #from a different port as a clock source to this #port. FOR THIS OPTION TO WORK: TE_CLOCK=MASTER #Valid options: 0 - disable # 1-4 - use clock from particular port ACTIVE_CH = ALL #Specify T1/E1 Active channels (timeslots) #Since AFT cards support channelization this #option MUST BE HARDCODED TO: ALL! TE_HIGHIMPEDANCE = NO #Set the Front Ent chip in High Impedance mode #used for datascoping: #NO - Disable high impedance mode (DEFAULT) #YES - Enable hight impedance mode # (only if you know what you are doing) LBO = 0DB #Front End Line Buildout # 0db (Default) # 7.5dB # 15dB # 22.5dB # 0-110ft # 110-220ft # 220-330ft # 330-440ft # 440-550ft # 550-660ft FE_TXTRISTATE = NO #Front End Tri-State Mode #Disable front end chip TX mode #Used for datascoping or connecting multiple ports #together where one port is operating normally and others #are tristated, thus only receiving. #NO - Disable tristae mode #YES- Enable tristate mode MTU = 1500 #Global MTU Value #Note: This value is overwritten by the # interface MTU value below if it exists. #Values: any number [ suggested 128 - 4086 ] UDPPORT = 9000 #OBSELETE option #Old wanpipemon used sockets to connect to #device driver. TTL = 255 #OBSELETE option #Old wanpipemon used sockets to connect to #device driver. IGNORE_FRONT_END = NO #Ignore Fronte End State #NO - Do not ignore front end state, # therefore if state changes, change the # state of the above protocol. #YES- Igonore front end state # Thus if front end goes down, the protocol # will not know. #-------------------------------------------- #Protocol Interface Configuration #-------------------------------------------- [w1g1fr] CIR = 0 #OBSOLETE: Not used by AFT cards BC = 0 #OBSOLETE: Not used by AFT cards BE = 0 #OBSOLETE: Not used by AFT cards INARP = NO #OBSOLETE: Not used by AFT cards INARPINTERVAL = 0 #OBSOLETE: Not used by AFT cards INARP_RX = NO #OBSOLETE: Not used by AFT cards IPX = NO #OBSOLETE: Not used by AFT cards MULTICAST = NO #Enable/Disable MULTICAST flag on this interface #NO - Disable #YES- Enable DYN_INTR_CFG = NO #Enable Dynamic IP addressing if supported by #protocol. #NO - Disable Dynamic IP addressing #YES- Eanble Dynamic IP addressing TRUE_ENCODING_TYPE = NO #OBSOLETE: Not used by AFT cards GATEWAY = NO #Indicates that this interface is a default #gateway interface. Used by dynamic IP code. #NO - This interface is not gateway #YES- This interface is a gateway LIP_MTU = 1500 #OPTIONAL #MTU for LIP Interface #Values: 128 to 4096 #Note! This value should not be greater # Than MTU for lower interfaces #If not defined: default 1500 #-------------------------------------------- #Protocol Profile Configuration #-------------------------------------------- [w1g1.fr] NUMBER_OF_DLCI = 1 #Number of DLCI's #Important when configured for NODE! Station = CPE #Station Configuration #CPE - customer end point #NODE - frame relay switch emulation. SIGNALLING = AUTO #Frame Relay Signalling #AUTO - Tries to autodetect frame relay # signalling (CPE mode only) #ANSI #LMI #Q933 T391 = 10 T392 = 16 N391 = 6 N392 = 6 N393 = 4 FR_ISSUE_FS = YES #OBSOLETE Not used by AFT cards #------------------------------------------- #Hardware Interface Configuration #------------------------------------------- [w1g1] HDLC_STREAMING = YES #Enable HDLC engine on this interface #YES - HDLC engine enabled. # All frames Rx/Tx from/to this interface # will be in HDLC format. #NO - HDLC engine disabled. # Rx/Tx Transparent (Raw) bits to and from # interface. ACTIVE_CH = ALL #Timeslot binding #Specify what T1/E1 timeslots should be boudned #to this interface. #ALL - All timeslots #1-5 - 1 to 5 #1.5 - 1 and 5 #1-10.11-20 - 1 to 10 and 11 to 20 MTU = 1500 #OPTIONAL #Maximum Tx Size for this interface #if this value is NOT set the global #MTU value will be used MRU = 1500 #OPTIONAL #Maximum Rx Size for this interface #if this value is NOT set the global #MRU value will be used