#================================================ # WANPIPE1 Configuration File #================================================ # # Date: Wed Oct 12 10:48:34 EDT 2005 # # Note: This file was generated automatically # by /usr/sbin/wancfg program. # # If you want to edit this file, it is # recommended that you use wancfg program # to do so. #================================================ # Sangoma Technologies Inc. #================================================ [devices] wanpipe1 = WAN_ADSL, Comment #WAN_ADSL indicates S518 ADSL card [interfaces] #-------- DRIVER INTERFACE DEFINITIONS -------------------------------- w1ad = wanpipe1, , PPPoE, Comment #PPPoE : Configure interface as Ethernet # so one can run PPPoE protocol over # it. (Roraing Penguin PPPoE) [wanpipe1] CARD_TYPE = S518 #S518: Same for all ADSL cards must #This value must be hardcoded to S518 for all #ADSL cards. AUTO_PCISLOT = YES #Auto detect PCI/BUS info for this card type #NO - disable this option #YES- enable this option # if enabled bottom two options # PCISLOT and PCIBUS will not be used. # Therefore one can set the to arbitrary value # or remove them all together. PCISLOT = 2 #PCI SLOT Number: #Valid values = any number PCIBUS = 2 #PCI BUS Number: #Valid values = any number ENCAPMODE = ETH_LLC_OA #ATM Encapsulation Mode #ETH_LLC_OA: Bridged Ethernet over ATM # ATM will expect incoming and outgoing # ethernet protocol frames. # LLC ATM headers. #ETH_VC_OA : Bridged Ethernet over ATM # No ATM headers. #IP_LLC_OA : Classical IP over ATM # LLC ATM headers #IP_VC_OA : IP over ATM # No ATM headers #PPP_LLC_OA: #PPP_VC_OA : ATM_AUTOCFG = NO #Attempt to autodetect VPI/VCI numbers #Default NO. VCI = 35 #VCI Value VPI = 0 #VPI Value ADSL_WATCHDOG = YES #Use ATM PING to test the line status #If ATM PING failes the line will be restarted #-------------ADSL INTERNAL VARIALBES ------------------ VERBOSE = 1 #ADSL internal variable set to 1 #No other options RXBUFFERCOUNT = 50 #Rx buffer count #No other options TXBUFFERCOUNT = 50 #Tx buffer count #No other optiosn ADSLSTANDARD = ADSL_MULTIMODE #ADSL Standard #ADSL_MULTIMODE : (Default) # Automatically detect ADSL standard # We never needed to change this option #ADSL_T1_413 #ADSL_G_LITE #ADSL_G_DMT #ADSL_ALCATEL_1_4 #ADSL_ADI #ADSL_ALCATEL #ADSL_T1_413_AUTO ADSLTRELLIS = ADSL_TRELLIS_ENABLE #Trellis Enable/Disable #ADSL_TRELLIS_ENABLE : (Default) # We never needed to change this option #ADSL_TRELLIS_DISABLE ADSLTXPOWERATTEN = 0 #ADSL Tx Power Attenuation # #*** This a valuable variable and it also works in # conjuction with ADSLCODINGGAIN # #Integer Value 0 to 6 # 0 (Deafult) # 3 or 6 (*MAGIC: Found that it helps if the line is noisy # and ADSL is constantly retraining) ADSLCODINGGAIN = ADSL_AUTO_CODING_GAIN #ADSL Coding Gain # #*** This a valuable variable and it also works well in # conjuction with ADSLTXPOWERATTEN # #ADSL_AUTO_CODING_GAIN : (Default) # #ADSL_0DB_CODING_GAIN #ADSL_1DB_CODING_GAIN #ADSL_2DB_CODING_GAIN #ADSL_3DB_CODING_GAIN (MAGIC: Found that helps in conjucture with # ADSLTXPOWERATTEN=3) #ADSL_4DB_CODING_GAIN #ADSL_5DB_CODING_GAIN #ADSL_6DB_CODING_GAIN #ADSL_7DB_CODING_GAIN ADSLMAXBITSPERBIN = 0xE #Maximum Bits per Bin #Valid Values 0x01-0xF # #Determines the overall baud rate of theline. # #Theoretically it can help on very noisy lines #by lowering the value and using less frequency #ranges to tx/rx data. #The Start/End Tx/Rx Freqeuncy Ranges (Bins) #Can theoretically lower the bandwidth #on noisy lines, in order to avoid higher #unstable frequency ranges. #However, this never worked in practice #thus our suggestion is to not try to set #these values. ADSLTXSTARTBIN = 0x6 #Start Tx Frequency Range (Bin) #Do not adjust ADSLTXENDBIN = 0x1F #End Tx Frequency Range (Bin) #Do not adjust ADSLRXSTARTBIN = 0x20 #Start Rx Frequency Range (Bin) #Do not adjust ADSLRXENDBIN = 0xFF #End of Rx Frequency Range (Bin) #Do not adjust ADSLRXBINADJUST = ADSL_RX_BIN_DISABLE #Disable Rx Frequency Ranges #Do not ajust ADSLFRAMINGSTRUCT = ADSL_FRAMING_TYPE_3 #ADSL Framing #ADSL_FRAMING_TYPE_0 #ADSL_FRAMING_TYPE_1 #ADSL_FRAMING_TYPE_2 #ADSL_FRAMING_TYPE_3 (Default) #Do not adjust ADSLEXPANDEDEXCHANGE = ADSL_EXPANDED_EXCHANGE #ADSL Exchange #ADSL_EXPANDED_EXCHANGE (Default) #ADSL_SHORT_EXCHANGE #Do not adjust ADSLCLOCKTYPE = ADSL_CLOCK_CRYSTAL #ADSL Clocking #ADSL_CLOCK_CRYSTAL : Slave Clocking (Default) #ADSL_CLOCK_OSCILLATOR : Master Clock #Do not adjust ADSLMAXDOWNRATE = 8192 #ADSL Max Baudrate #This value WILL limit the negotiaged baudrate #Value is in Kilobits per second # #So by setting the value to 1000 the highest #rx baud rate will by 1Mbps. # #Theoretically it can help on very noisy lines #by lowering the value and using less frequency #ranges to tx/rx data. # #Doesn't work in reality :) #Do not adjust MTU = 1500 #Global MTU Value #Note: This value is overwritten by the # interface MTU value below if it exists. #DEFAULT: 1500 #Values: any number [ suggested 128 - 4086 ] UDPPORT = 9000 #OBSELETE option #Old wanpipemon used sockets to connect to #device driver. TTL = 255 #OBSELETE option #Old wanpipemon used sockets to connect to #device driver. IGNORE_FRONT_END = NO #Ignore Fronte End State #NOT USED BY ADSL [w1ad]