* make sure all projects and relevant links are mentioned * indicate which sub-directories relate to which project * use markdown syntax Change-Id: If126790c5652a6228e8a8ad1986e3b08adf46faechanges/22/29922/4
parent
6e2150ee0c
commit
a0df047214
@ -1,47 +0,0 @@
|
||||
osmo-e1-hardware - Collection of various E1/TDM hardware projects
|
||||
======================================================================
|
||||
|
||||
This repository hosts three different sub-projects:
|
||||
|
||||
* osmo-e1-xcvr (E1 LIU + magnetics)
|
||||
https://osmocom.org/projects/e1-t1-adapter/wiki/Osmo-e1-xcvr
|
||||
* osmo-e1-tracer (fully integrated passive raw bitstream tracer)
|
||||
https://osmocom.org/projects/e1-t1-adapter/wiki/E1_tracer
|
||||
* osmo-e1-tap (passive high-impedance tap)
|
||||
|
||||
== osmo-e1-xcvr ==
|
||||
|
||||
This is a simple hardware project that aims to generate a reusable module
|
||||
for interfacing E1/T1/J1 lines from various custom FPGA/CPLD/microcontroller
|
||||
projects.
|
||||
|
||||
The board contains tranformers, the analog circuitry, the LIU (line interface
|
||||
unit), an oscillator as well as an integrated transceiver chip.
|
||||
|
||||
It exposes the control interface (SPI) as well as the decoded synchronous
|
||||
Rx/Tx bitstreams each on a 2x5pin header.
|
||||
|
||||
Framer, Multiplexe,r HDLC decoder or anything like that is out-of-scope for
|
||||
now. The idea relaly is to provide an interface as low-level as possible.
|
||||
|
||||
One of the ideas is to create a "soft E1" interface, where the Rx/Tx bitstreams
|
||||
are interfaced with the SSC of an AT91SAM3S and subsequently passed into a PC
|
||||
via USB. The 2Mbps signal is very low-bandwidth, so that a pure software
|
||||
implementation should be absolutely no problem for todays computing power.
|
||||
|
||||
See https://osmocom.org/projects/e1-t1-adapter/wiki/Osmo-e1-xcvr for more details
|
||||
|
||||
|
||||
== osmo-e1-tap ==
|
||||
|
||||
This is a small passive board that allows you to perform high-impedance tracing on an E1
|
||||
or T1 line.
|
||||
|
||||
|
||||
== osmo-e1-tracer ==
|
||||
|
||||
This is a fully integrated design that allows you to obtainm bi-directional high-impedance
|
||||
bitstream E1 traces. It features an iCE40 FPGA with USB + E1 cores from Sylvain Munaut,
|
||||
as well as two E1 LIUs.
|
||||
|
||||
See https://osmocom.org/projects/e1-t1-adapter/wiki/E1_tracer for more details.
|
||||
@ -0,0 +1,94 @@
|
||||
osmo-e1-hardware - Collection of various E1/TDM hardware projects
|
||||
=================================================================
|
||||
|
||||
This repository contains a variety of different projects related to
|
||||
E1/TDM hardware interfaces
|
||||
|
||||
* `icE1usb` (fully-fledged USB E1 interface adapter)
|
||||
* `osmo-e1-tracer` (fully integrated passive raw bitstream tracer)
|
||||
* `osmo-e1-tap` (passive high-impedance E1/T1 tap)
|
||||
* `osmo-e1-xcvr` (E1 LIU + magnetics)
|
||||
https://osmocom.org/projects/e1-t1-adapter/wiki/Osmo-e1-xcvr
|
||||
|
||||
icE1usb
|
||||
-------
|
||||
|
||||
The Osmocom icE1usb project is an open source hardware, gateware and firmware
|
||||
project implementing a USB-attached interface for E1 circuits. Use this
|
||||
if you want to implement a system speaking to an E1 circuit, such as
|
||||
* a GSM BSC (using [OsmoBSC](https://osmocom.org/projects/osmobsc/wiki)) talking Abis/E1 to a GSM Base station,
|
||||
* using [osmo-gbproxy](https://osmocom.org/projects/osmo-gbproxy/wiki/Osmo-gbproxy) to convert classing Gb/E1 to Gb/IP
|
||||
* talking to legacy ISDN PRI equipment such as PBX, RAS servers, etc.
|
||||
* connecting legacy ISDN PRI equipment such as PBX, RAS servers, etc. to
|
||||
the [OCTOI comminity TDMoIP network](https://osmocom.org/projects/octoi/wiki)
|
||||
|
||||
Depending on your USB host controller, it supports one or two E1
|
||||
circuits. Most host controllers can only support one E1 circuit.
|
||||
|
||||
In order to provide a stable E1 clock reference, it contains a GPS disciplined oscillator.
|
||||
|
||||
See <https://osmocom.org/projects/e1-t1-adapter/wiki/IcE1usb> for more details.
|
||||
|
||||
Fully assembled units can be purchased at the [sysmocom
|
||||
webshop](https://shop.sysmocom.de/Osmocom-icE1usb-E1-interface-for-USB/icE1usb-kit)
|
||||
|
||||
Check the `hardware/icE1usb`, `firmware/ice40-riscv/icE1usb` directories in this repository.
|
||||
|
||||
The host software is provided either
|
||||
* via [osmo-e1d](https://osmocom.org/projects/osmo-e1d/wiki), or
|
||||
* via the [icE1usb DAHDI driver](https://gitea.osmocom.org/retronetworking/dahdi-linux)
|
||||
|
||||
|
||||
osmo-e1-tracer
|
||||
--------------
|
||||
|
||||
This is a fully integrated design that allows you to obtain bi-directional high-impedance
|
||||
bitstream E1 traces. It features an iCE40 FPGA with USB + E1 cores from Sylvain Munaut,
|
||||
as well as two E1 LIUs.
|
||||
|
||||
See <https://osmocom.org/projects/e1-t1-adapter/wiki/E1_tracer> for more details.
|
||||
|
||||
Fully assembled units can be purchased made-to-order from
|
||||
[sysmocom](https://sysmocom.de).
|
||||
|
||||
Check the `hardware/e1-tracer`, `firmware/ice40-riscv/e1-tracer` and `software/e1-tracer`
|
||||
directories in this repository.
|
||||
|
||||
|
||||
osmo-e1-xcvr
|
||||
------------
|
||||
|
||||
This was a simple hardware project that aims to generate a reusable module
|
||||
for interfacing E1/T1/J1 lines from various custom FPGA/CPLD/microcontroller
|
||||
projects. Consider it part of an earlier R&D setup before icE1usb and
|
||||
osmo-e1-tracer were around.
|
||||
|
||||
The board contains transformers, the analog circuitry, the LIU (line interface
|
||||
unit), an oscillator as well as an integrated transceiver chip.
|
||||
|
||||
It exposes the control interface (SPI) as well as the decoded synchronous
|
||||
Rx/Tx bitstreams each on a 2x5pin header.
|
||||
|
||||
Framer, Multiplexer, HDLC decoder or anything like that is out-of-scope for
|
||||
now. The idea really is to provide an interface as low-level as possible.
|
||||
|
||||
One of the ideas is to create a "soft E1" interface, where the Rx/Tx bitstreams
|
||||
are interfaced with the SSC of an AT91SAM3S and subsequently passed into a PC
|
||||
via USB. The 2Mbps signal is very low-bandwidth, so that a pure software
|
||||
implementation should be absolutely no problem for todays computing power.
|
||||
|
||||
See <https://osmocom.org/projects/e1-t1-adapter/wiki/Osmo-e1-xcvr> for more details
|
||||
|
||||
Check the `hardware/e1-xcvr` directory in this repository.
|
||||
|
||||
|
||||
osmo-e1-tap
|
||||
-----------
|
||||
|
||||
This is a small passive board that allows you to perform high-impedance tracing on an E1
|
||||
or T1 line.
|
||||
|
||||
Fully assembled units can be purchased at the [sysmocom
|
||||
webshop](https://shop.sysmocom.de/E1-T1-tap-adapter/e1-tap).
|
||||
|
||||
Check the `hardware/e1-tap` directory in this repository.
|
||||
Loading…
Reference in new issue