158 lines
3.5 KiB
Groff
158 lines
3.5 KiB
Groff
.\" Process this file with
|
|
.\" groff -man -Tascii hisaxctrl.1 for ASCII output, or
|
|
.\" groff -man -Tps hisaxctrl.1 for PostScript output
|
|
.\"
|
|
.TH HISAXCTRL 8 "August 2001" isdn4k-utils-@I4LVERSION@ "Linux System Administration"
|
|
.SH NAME
|
|
hisaxctrl \- configure HiSax-Module
|
|
.SH SYNOPSIS
|
|
.B hisaxctrl
|
|
.I DriverId command parameters
|
|
.SH DESCRIPTION
|
|
.B hisaxctrl
|
|
is used to setup the HiSax-ISDN device driver.
|
|
All logging-output is sent to the device /dev/isdnctrl. So you can show it
|
|
by executing
|
|
.BR "cat /dev/isdnctrl" .
|
|
.br
|
|
.B NOTE:
|
|
for
|
|
.I devfs
|
|
systems, the program will automatically use /dev/isdn/isdnctrl if available.
|
|
.LP
|
|
The use of
|
|
.I hisaxctrl
|
|
only makes sense if you are using the HiSax driver.
|
|
.LP
|
|
.SH OPTIONS
|
|
.TP
|
|
.I DriverId
|
|
is used to identify the card when using more than one passive card. While
|
|
loading the hisax module with
|
|
.IR insmod ", or " modprobe
|
|
the DriverId is set by appending
|
|
.BI id= idstring1 % idstring2 %...
|
|
to the commandline.
|
|
.LP
|
|
.TP
|
|
.I command
|
|
is an integer selecting the setup category. The following values are
|
|
defined for setting the logging-level of the HiSax-ISDN device driver:
|
|
.LP
|
|
.RS
|
|
.BR " 0" " reports card status infos."
|
|
.br
|
|
.BR " 1" " selects generic debugging."
|
|
.br
|
|
.BR 11 " selects layer 1 development debugging."
|
|
.br
|
|
.BR 13 " selects layer 3 development debugging."
|
|
.br
|
|
.RE
|
|
.LP
|
|
the following commands are used to enable special features during runtime
|
|
of the HiSax-ISDN device driver.
|
|
.LP
|
|
.RS
|
|
.BR " 2" " set B-channel ON delay to parameter (in ms)"
|
|
.br
|
|
.BR " 5" " set B-channel in leased mode"
|
|
.br
|
|
.BR " 6" " set B-channel in TESTLOOP mode"
|
|
.br
|
|
.BR " 7" " set/reset card in Point To Point mode"
|
|
.br
|
|
.BR " 8" " set card in FIXED TEI mode "
|
|
.br
|
|
.BR " 9" " load firmware for DSP cards"
|
|
.br
|
|
.BR "10" " set B-channel usage limit to 1 or 2 channels"
|
|
.br
|
|
.BR "12" " set echo logging mode (only for some cards)"
|
|
.br
|
|
.BR " " " B-channel usage limit needs to be 1 if enabled"
|
|
.br
|
|
.RE
|
|
.TP
|
|
.I parameter
|
|
If the command is
|
|
.BR 9
|
|
then the parameter is the full pathname to the file containing the firmware.
|
|
|
|
For debug settings this is an integer representing a bitmask. Every bit in
|
|
this mask switches a debug facility on or off. Depending on the selected
|
|
category, the following values are defined:
|
|
.LP
|
|
.RS
|
|
.RB With " generic debugging " selected
|
|
.br
|
|
(command \fB1\fR):
|
|
.LP
|
|
.BR 0x001 " Link-level <--> hardware-level communication"
|
|
.br
|
|
.BR 0x002 " Top state machine"
|
|
.br
|
|
.BR 0x004 " D-Channel Q.931 (call control messages)"
|
|
.br
|
|
.BR 0x008 " D-Channel Q.921"
|
|
.br
|
|
.BR 0x010 " B-Channel X.75"
|
|
.br
|
|
.BR 0x020 " D-Channel l2"
|
|
.br
|
|
.BR 0x040 " B-Channel l2"
|
|
.br
|
|
.BR 0x080 " D-Channel link state debugging"
|
|
.br
|
|
.BR 0x100 " B-Channel link state debugging"
|
|
.br
|
|
.BR 0x200 " TEI debug"
|
|
.br
|
|
.BR 0x400 " LOCK debug in callc.c"
|
|
.br
|
|
.BR 0x800 " More debug in callc.c (not for normal use)"
|
|
.br
|
|
.LP
|
|
.RB With " layer 1 development debugging " selected
|
|
.br
|
|
(command \fB11\fR):
|
|
.LP
|
|
.BR 0x001 " Warnings (default: on)"
|
|
.br
|
|
.BR 0x002 " IRQ status"
|
|
.br
|
|
.BR 0x004 " ISAC"
|
|
.br
|
|
.BR 0x008 " ISAC FIFO"
|
|
.br
|
|
.BR 0x010 " HSCX"
|
|
.br
|
|
.BR 0x020 " HSCX FIFO (attention: full B-Channel output!)"
|
|
.br
|
|
.BR 0x040 " D-Channel LAPD frame types"
|
|
.br
|
|
.LP
|
|
.RB With " layer 3 development debugging " selected
|
|
.br
|
|
(command \fB13\fR):
|
|
.LP
|
|
.BR 0x001 " Warnings (default: on)"
|
|
.br
|
|
.BR 0x002 " l3 protocol discriptor errors"
|
|
.br
|
|
.BR 0x004 " l3 state machine"
|
|
.br
|
|
.BR 0x008 " charge info debugging (1TR6)"
|
|
.br
|
|
.RE
|
|
.LP
|
|
.SH EXAMPLE
|
|
.TP
|
|
.BI hisaxctrl " HiSax 1 0x3ff"
|
|
enables full generic debugging.
|
|
.SH AUTHOR
|
|
\(co 2000 by Karsten Keil <kkeil@suse.de>
|
|
.LP
|
|
.SH SEE ALSO
|
|
.BR isdnctrl "(8), " isdn_cause "(7), " isdninfo (4).
|