Exposed in twinstar setups where dahdi has auto_assign_spans=1:
* We start configuration with an empty /etc/dahdi/xpp_order
* If "XPP_HOTPLUG_DAHDI=yes", the astribank_hook removes
the asterisk_is_starting semaphore too early.
* There's no point in waiting for non-existant or empty /etc/dahdi/xpp_order
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Don't run the final astribank_is_starting if asterisk is hotpluggable.
Likewise, if there's no xpp_order file, waiting is pointless as the hook
can't count Astribanks.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Fixes a regression since 949ea4ca9f
(2.7.0) - allows using an Astribank with no serial.
* Some of the olderst Astribanks don't have a serial number burned in
them. Thus there is no serial attribute for the sysfs USB device node.
* waitfor_xpds identifies the Astribanks by their serial numbers.
* An lone Astribank without serial number would thus block waitfor_xpds
(until timeout).
* Now we warn about them.
* We also try to handle it gracefully. As long as there's only one
of thease, it would be counted as "NO-SERIAL".
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
* Fix an issue due to long firmware load time:
- When one Astribank has an echo canceler (long firmware loading) and
and another one does not.
- The EC-less Astribank finishes initialization before the Astribank
with EC is detected.
- Thus waitfor_xpds terminates too early.
* We now iteratively build two sets of serial numbers:
- One from wha we see in all Xorcom (e4e4:11[3456]x) USB devices.
- The other is those that were detected in the driver.
- Only when the two sets are equal (and > 0) we know we are done.
- This is resilient to many problems (e.g: disconnect/reconnect of
same device during initialization).
* The progress output was also improved: Now each detected AB
show the total number so far.
* The timeout was also increased to 100sec
* Woraround for an Astribank with no serial (but just a single one on
the system).
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.astersk.org/svn/dahdi/tools/trunk@10465 17933a7a-c749-41c5-a318-cba88f637d49
On several pathological cases we may need to wait more than 40 seconds.
Make that timeout configurable.
git-svn-id: http://svn.astersk.org/svn/dahdi/tools/trunk@10177 17933a7a-c749-41c5-a318-cba88f637d49
Echo Cancellation firmware is loaded by xpp/stribank_hexload
(Using the oct612x code).
* astribank_hexload: options -O/-o/-A for handling the Octasic echo
cancellation firmware.
* astribank_tool: report that.
* xpp_fxloader: Run astribank_hexload, if needed.
* dahdi_perl: The EC module is an extra XPD, but not a "telephony device"
and hence not a span. Deal with that.
* waitfor_xpds: may need to wait a bit longer for firmware loading.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.astersk.org/svn/dahdi/tools/trunk@10032 17933a7a-c749-41c5-a318-cba88f637d49
Oron Peled