203 lines
5.1 KiB
C
203 lines
5.1 KiB
C
/*
|
|
* DAHDI configuration options
|
|
*
|
|
*/
|
|
|
|
/*
|
|
* See http://www.asterisk.org for more information about
|
|
* the Asterisk project. Please do not directly contact
|
|
* any of the maintainers of this project for assistance;
|
|
* the project provides a web site, mailing lists and IRC
|
|
* channels for your use.
|
|
*
|
|
* This program is free software, distributed under the terms of
|
|
* the GNU General Public License Version 2 as published by the
|
|
* Free Software Foundation. See the LICENSE file included with
|
|
* this program for more details.
|
|
*/
|
|
|
|
#ifndef _DAHDI_CONFIG_H
|
|
#define _DAHDI_CONFIG_H
|
|
|
|
#ifdef __KERNEL__
|
|
#include <linux/version.h>
|
|
#endif
|
|
|
|
/* DAHDI compile time options */
|
|
|
|
/* These default tone lengths are in units of milliseconds. */
|
|
#define DAHDI_CONFIG_DEFAULT_DTMF_LENGTH 100
|
|
#define DAHDI_CONFIG_DEFAULT_MFR1_LENGTH 68
|
|
#define DAHDI_CONFIG_DEFAULT_MFR2_LENGTH 100
|
|
#define DAHDI_CONFIG_PAUSE_LENGTH 500
|
|
|
|
/*
|
|
* Uncomment if you have a European phone, or any other phone with a
|
|
* short flash time.
|
|
* This will stop the flash being mis-detected as a pulse dial "1" on
|
|
* phones with short flashes
|
|
*/
|
|
/* #define SHORT_FLASH_TIME */
|
|
|
|
/*
|
|
* Uncomment to disable calibration tests
|
|
* (not generally recommended)
|
|
*/
|
|
/* #define NO_CALIBRATION */
|
|
|
|
/*
|
|
* Boost ring voltage (Higher ring voltage, takes more power)
|
|
* Note: this only affects the wcfxsusb and wcusb drivers; all other
|
|
* drivers have a 'boostringer' module parameter.
|
|
*/
|
|
/* #define BOOST_RINGER */
|
|
|
|
/*
|
|
* Define CONFIG_CALC_XLAW if you have a small number of channels and/or
|
|
* a small level 2 cache, to optimize for few channels
|
|
*
|
|
*/
|
|
/* #define CONFIG_CALC_XLAW */
|
|
|
|
/*
|
|
* Define if you want MMX optimizations in DAHDI
|
|
*
|
|
* Note: CONFIG_DAHDI_MMX is generally incompatible with AMD
|
|
* processors and can cause system instability!
|
|
*
|
|
*/
|
|
/* #define CONFIG_DAHDI_MMX */
|
|
|
|
/* We now use the linux kernel config to detect which options to use */
|
|
/* You can still override them below */
|
|
#if defined(CONFIG_HDLC) || defined(CONFIG_HDLC_MODULE)
|
|
#define DAHDI_HDLC_TYPE_TRANS
|
|
#define HDLC_MAINTAINERS_ARE_MORE_STUPID_THAN_I_THOUGHT
|
|
#endif
|
|
|
|
/*
|
|
* Uncomment CONFIG_DAHDI_NET to enable SyncPPP, CiscoHDLC, and Frame Relay
|
|
* support.
|
|
*/
|
|
#define CONFIG_DAHDI_NET
|
|
#define CONFIG_DAHDI_PPP
|
|
|
|
/*
|
|
* Uncomment for Generic PPP support (i.e. DAHDIRAS)
|
|
*/
|
|
|
|
#if defined(CONFIG_PPP) || defined(CONFIG_PPP_MODULE)
|
|
/* #define CONFIG_DAHDI_PPP */
|
|
#endif
|
|
|
|
/*
|
|
* Uncomment to enable "watchdog" to monitor if interfaces
|
|
* stop taking interrupts or otherwise misbehave
|
|
*/
|
|
/* #define CONFIG_DAHDI_WATCHDOG */
|
|
|
|
/*
|
|
* Uncomment the following to include extra debugging output.
|
|
*/
|
|
/* #define CONFIG_DAHDI_DEBUG */
|
|
|
|
/*
|
|
* Uncomment for Non-standard FXS groundstart start state (A=Low, B=Low)
|
|
* particularly for CAC channel bank groundstart FXO ports.
|
|
*/
|
|
/* #define CONFIG_CAC_GROUNDSTART */
|
|
|
|
/*
|
|
* Define CONFIG_DAHDI_CORE_TIMER if you would like dahdi to always provide a
|
|
* timing source regardless of which spans / drivers are configured.
|
|
*/
|
|
#define CONFIG_DAHDI_CORE_TIMER
|
|
|
|
/*
|
|
* Define CONFIG_DAHDI_NO_ECHOCAN_DISABLE to prevent the 2100Hz tone detector
|
|
* from disabling any installed software echocan.
|
|
*
|
|
*/
|
|
/* #define CONFIG_DAHDI_NO_ECHOCAN_DISABLE */
|
|
|
|
/*
|
|
* Define if you would like to allow software echocans to process the tx audio
|
|
* in addition to the rx audio. Used for things like DC removal.
|
|
*
|
|
*/
|
|
/* #define CONFIG_DAHDI_ECHOCAN_PROCESS_TX */
|
|
|
|
/*
|
|
* Uncomment if you happen have an early TDM400P Rev H which
|
|
* sometimes forgets its PCI ID to have wcfxs match essentially all
|
|
* subvendor ID's
|
|
*/
|
|
/* #define TDM_REVH_MATCHALL */
|
|
|
|
/*
|
|
* Uncomment the following if you want to support E&M trunks being
|
|
* able to "flash" after going off-hook (dont ask why, just nod :-) ).
|
|
*
|
|
* NOTE: *DO NOT* Enable "EMFLASH" and "EMPULSE" at the same time!!
|
|
*
|
|
*/
|
|
/* #define EMFLASH */
|
|
|
|
/*
|
|
* Uncomment the following if you want to support E&M trunks being
|
|
* able to recognize Dial Pulse digits. This can validly be enabled
|
|
* so that either Dial Pulse or DTMF/MF tones will be recognized, but
|
|
* the drawback is that the ONHOOK will take an extra {rxwinktime}
|
|
* to be recognized.
|
|
*
|
|
* NOTE: *DO NOT* Enable "EMFLASH" and "EMPULSE" at the same time!!
|
|
*
|
|
*/
|
|
/* #define EMPULSE */
|
|
|
|
/*
|
|
* Comment out the following if you dont want events to indicate the
|
|
* beginning of an incoming ring. Most non-Asterisk applications will
|
|
* want this commented out.
|
|
*/
|
|
#define RINGBEGIN
|
|
|
|
/*
|
|
* Uncomment the following if you need to support FXS Flash events.
|
|
* Most applications will want this commented out.
|
|
*/
|
|
/* #define FXSFLASH */
|
|
|
|
/*
|
|
* Enable sync_tick() calls. Allows low-level drivers to synchronize
|
|
* their internal clocks to the DAHDI master clock.
|
|
*/
|
|
#define DAHDI_SYNC_TICK
|
|
|
|
/*
|
|
* Skip processing PCM if low-level driver won't use it anyway
|
|
*/
|
|
/* #define OPTIMIZE_CHANMUTE */
|
|
|
|
|
|
/*
|
|
* Pass DAHDI_AUDIOMODE to channel driver as well
|
|
*/
|
|
/* #define DAHDI_AUDIO_NOTIFY */
|
|
|
|
/*
|
|
* Creates an interface for mirroring the raw channel data out to a pseudo-chan
|
|
*/
|
|
#define CONFIG_DAHDI_MIRROR
|
|
|
|
/*
|
|
* Adds support for conference links. There are some non-Asterisk users of this
|
|
* functionality.
|
|
*/
|
|
/* #define CONFIG_DAHDI_CONFLINK */
|
|
|
|
#define CONFIG_DAHDI_DYNAMIC
|
|
#define CONFIG_DAHDI_DYNAMIC_LOC
|
|
|
|
#endif
|