According to spec, the lowest numbered PDCH of the TBF shall be used
for the PACCH, only when concurrent TBF are active, the lowest common
PDCH shall be used. An immediate assigment is in general only sent,
if no TBF is active, so the latter case never applies.
This reverts commit fdd8a1ba2312be3f33576ee994c0b5da6272e815.
Make use of variables, log them to LOGL_DEBUG, and reduce code
duplication.
This should help to narrow down the cause why snd_dl_ass are not
answered by the MS sometimes.
Sponsored-by: On-Waves ehf
Currently the plain 'egprs' command enables EGPRS but doesn't prevent
phones from being served in GPRS mode if they do not support EGPRS.
This involves complex frame allocation implementations in dynamic
mode, especially if 8PSK is being used. This is due to the inability
of non-EGPRS phone to decode 8PSK USF and ES/P altogether. Since
polling has a higher priority than USF, collisions will have to be
prevented by the PCU by never using an GPRS USF if it refers to a FN
that is already being used for polling.
This commit just disables mixed usage by ignoring GPRS-only request
if EGPRS is enabled.
The following VTY command (config-pcu node) is changed:
egprs -> egprs only
Sponsored-by: On-Waves ehf
Currently this message is ignored.
Support decoding and handling of this message. Use a bitvec for the
decoder that just represents a BSN sequence without any encoding
details (first bit -> first BSN). Return the corresponding BSN range
(snsmod(bsn_begin + bits_in_bitvec) = bsn_end), so snsmod(bsn_end-1)
is the last BSN if there is at least 1. If bsn_begin == bsn_end, no
BSNs has been added.
Note that this bitvec is not yet used for RBB handling. It just calls
the old rcvd_dl_ack with a faked (all bits are 1) RBB map.
Sponsored-by: On-Waves ehf
Currently the RLC message length that is obtained from the DSP is
reduced by 1 if the last byte of the buffer includes spare bits.
While this worked well with GPRS, these bits are being used to
encode RLC blocks in EGPRS mode. Thus this last byte must not be
chopped off. The functionality of the code is not affected by this,
since the modified length value is not used.
This commit adds GprsCodingScheme::usedSizeDL/UL to return
the number of bytes needed to encode the message block. If there are
single bits at the end that are to be used (EGPRS), the functions
return the number of full bytes plus 1 (which is the buffer size
reported by the DSP and returned by sizeUL/sizeDL). The commit also
removes the len parameter from rcv_data_block_acknowledged.
Sponsored-by: On-Waves ehf
These struct names are more specific than necessary. They are used
for GPRS (uplink) already. In downlink direction, only a few fields
will be added to the header struct. Add addition,
gprs_rlc_ul_header_egprs does not map directly to an encoded
header, like many other 'header' structs do.
Change the names to fit both modes and both directions:
gprs_rlc_ul_header_egprs -> gprs_rlc_data_info
gprs_rlc_ul_data_block_info -> gprs_rlc_data_block_info
Sponsored-by: On-Waves ehf
LListHead does basically the same like llist_pods, but more C++ish
and with type safety.
This commit turns the former list field of gprs_rlcmac_tbf into a
private field, provides accessors, moves the related code from
pcu_vty.c to pcu_vty_functions.cpp, and removes the llist_pods
type and related code.
Sponsored-by: On-Waves ehf
Currently casts from gprs_rlcmac_tbf to gprs_rlcmac_ul_tbf and
gprs_rlcmac_dl_tbf are done by using static_cast. This doesn't provide
protection against converting a gprs_rlcmac_ul_tbf pointer to a
gprs_rlcmac_dl_tbf pointer and vice versa.
This commit provides two functions as_ul_tbf and as_dl_tbf, that
behave similar like dynamic_cast but use the direction field instead
of RTTI.
Sponsored-by: On-Waves ehf
ASAN has found improper deletion of objects. These only occur
on shutdown but makes it impossible to run the test cases with
full ASAN support.
This commit fixes some of them and deactivates the freeing of the_pcu.bctx
which may cause a corruption in BTS::~BTS() later on.
Note that the latter is only a work-aound and should be fixed
properly. It will leak bctx objects, but this is currently not
critical, since gprs_bssgp_destroy is only called once, immediately
before a call to exit().
Ticket: OW#1572
Sponsored-by: On-Waves ehf
This commit removes the code that is no longer used due to the commit
"Use a single PDCH rcv_data_block method for GPRS and EGPRS".
Sponsored-by: On-Waves ehf
Currently GPRS is handled by the old code path while EGPRS already
uses the unified functions. The rcv_block_egprs is basically not
specific to EGPRS and just needs minor modifications to handle GPRS.
This commit turns gprs_rlcmac_pdch::rcv_block_egprs into a unified
rcv_data_block method and uses it for GPRS, too.
Note that the logging messages of the new parser are different.
Sponsored-by: On-Waves ehf
This commit replaces the stub by a method that decodes the block
first, and passes it to the TBF object associated with the TFI.
Sponsored-by: On-Waves ehf
This commit renames rcv_data_block_acknowledged to
rcv_data_block_acknowledged_gprs to separate it from EGPRS data block
decoding.
Sponsored-by: On-Waves ehf
Currently the block size is mapped by a switch statement to strip
extra bits that are not used for RLC blocks. That information is
already available via the GprsCodingScheme class.
This commit moves the CS/MCS detection to the rcv_block message and
passes the cs object via rcv_block_gprs, where the length gets
adjusted, to gprs_rlcmac_pdch::rcv_data_block_acknowledged. There the
switch statement is removed.
Note that the TbfTest.err changes due to an additional log message.
Sponsored-by: On-Waves ehf
The EGPRS MS class ist contained in the MS_RA_capability information.
Its presence indicates, that the MS is able (and willing) to use
EGPRS.
This commit implements basic support for retrieving, storing, and
showing it in the VTY. The information is stored in the MS object.
Sponsored-by: On-Waves ehf
Add a global stat_item group for measurement values and a
corresponding macro to get and set the values.
Add a stat_item STAT_MS_PRESET to monitor the number of
MS objects in the storage.
Sponsored-by: On-Waves ehf
When a timeout has occured several times, the procedures handled by
poll_timeout are aborted. This happens when the number of repetitions
exceed N3105. Currently only the timeouts themselves are counted.
This commits adds counters that are incremented if a procedure has
really failed.
New counter:
- rlc.ass.failed: Count failing UL and DL assigments via PACCH
- rlc.ack.failed: Count failing DL Ack/Nack requests
Sponsored-by: On-Waves ehf
Currently an existing DL TBF can get lost in the process of
establishing an UL TBF via RACH. This can lead to stalled connections
until the network sends more LLC frames.
This commit adds a check for a non-empty LLC queue after the UL TBF
has been established to rcv_control_ack (GPRS_RLCMAC_UL_ASS_WAIT_ACK
path) to eventually establish a new DL TBF on the UL TBF's PACCH.
Sponsored-by: On-Waves ehf
Currently an existing DL TBF is freed immediately, when a resource
request is received. This makes sense since the MS might have dropped
it when switching to the PDCH signaled via the AGCH for the SBA. But
if the TBF still is assumed to exist on the MS side, there might be
TFI collisions if the old TBF object is not kept to block its TFI
for some time.
This commit changes rcv_resource_request to call release() instead of
tbf_free() on the DL TBF object (if it exists).
Sponsored-by: On-Waves ehf
This reverts commit e91bd3babd.
That commit seems to cause hanging DL TBFs when there was a RACH
based UL TBF establishment while it that TBF is active. This could be
caused by the use of a different PDCH for the SBA.
Conflicts:
tests/tbf/TbfTest.cpp
tests/tbf/TbfTest.err
Currently all of these messages are discarded if they are assumend to
be caused by noise. But even in these cases, the FN and TN values
which are added by the DSP are valid. So these can be used to update
the current_frame value.
The osmo-bts sets the fBFILevel of a physical channel to -200dB if it
is used for PDTCH or PACCH which is the case for all PDCH. This way
a data_ind or ra_ind message is already send at least once per block
period (4 frames) per PDCH. These messages are passed to either
handle_ph_data_ind or handle_ph_ra_ind even if they contain garbage
data.
The ra_ind messages are sometimes sent a few frames earlier than
data_ind messages using the same frame.
This commit adds calls to update the current_frame value based on all
of these messages before they are discarded. The FN taken from ra_ind
are passed with an increased max_delay (5) to compensate for early
ra_ind messages.
Sponsored-by: On-Waves ehf
Currently a log entry is written if FN_data_ind - FN_time_ind <= -13.
This commit adds a counter 'rlc.late-block' that is incremented in
these cases.
Sponsored-by: On-Waves ehf
The FN of the data_ind taken from the DSP are monotonic, so latency
does not affect the detection of poll timeouts if these FN are used.
If the FN is larger than a poll_fn value, it can safely be assumed
that the poll response will not arrive later on.
Currently a max_delay of 60 frames is used, which has the drawback
that additional ~250ms will pass until a lost ACK is detected.
Using the data_ind's FN alone breaks the poll timeout detection if
there are no other MS sending data blocks.
This commit adds BTS::set_current_block_frame_number that is called
with the FN taken from data_ind messages. The max_delay is set to 0
which removes the additional delay, when this FN is used to detect
poll timeouts. So the average additional delay decreases with the
number of data_ind per time. The current_frame is updated unless it
seems to have been updated already (assumed if 0 < cur_fn - block_fn
< 500). Thus the time_ind has still priority to update the
current_frame value.
Sponsored-by: On-Waves ehf
Currently the max_delay parameter is set to 13, since that is
slightly above maximum number of frames that a time_ind can preceed a
block's data_ind of the same frame. This assumes that these messages
are not reordered after thay have been obtained from the DSP. In the
current implementation, the GPRS data_ind can directly be taken from
the DSP by the PCU while the time_ind messages are provided via the
BTS. So the messages are queued differently in that case, resulting
in a additional delay of the data_ind with respect to the time_ind.
The propability for this raises with a increased CPU load of the PCU.
If this happens, a poll timeout is detected by mistake and the poll
is either retried or cleared.
This commit increases the tolerance to 60 frames, since
values for FN_data_ind - FN_time_ind of up to 50 frames have been
observed under heavy PCU load.
Sponsored-by: On-Waves ehf
Currently the maximum additional delay is hard coded to 13. This
value depends on the source of the frame number value.
This commit adds the max_delay parameter to make it caller dependant.
Sponsored-by: On-Waves ehf
Currently all active TBF of an MS are killed if a Packet Resource
Request is received from the MS. In general this happens after a RACH
request. This does not happen after a resource request that has been
included into a Downlink Ack/Nack.
Sometimes an UL TBF is requested by an MS via RACH while a DL TBF is
running for instance to send a TCP Ack. This can happen, if a former
request via PACCH did not work.
This commit removes the killing of the DL TBF from
gprs_rlcmac_pdch::rcv_resource_request().
Sponsored-by: On-Waves ehf
Currently the TBFs are registered in a TFI indexed array within the TRX
objects. TBFs can be searched globally by TFI and TRX number. This
conflicts with the use of the same TFI for different TBF on different
PDCH. This use case requires the specification of the PDCH as
additional search dimension.
This commit moves the TFI index TBF arrays into the PDCH objects. The
related methods are updated accordingly.
Ticket: #1793
Sponsored-by: On-Waves ehf
Currently the TFI and the TRX have to be determined before the actual TBF
allocation function is called, passing TFI and TRX number as
parameters. This does fit to TFI reuse for different slots, since
this were tightly coupled with the slot selection.
This commit just moves the TFI selection into the alloc_algorithm
functions. The tfi parameter is removed from the the TFI alloc
functions. The trx parameter is changed into use_trx to optionally
limit the trx selection (same semantics like in tfi_find_free).
Sponsored-by: On-Waves ehf
Currently a single bit set is used to maintain a set of used TFI
without distinguishing between uplink and downlink. Since the
namespaces of UL and DL TFI are separate, this implementation is
not correct.
This commit changes gprs_rlcmac_pdch to use a separate bit set for
each direction. It also replace the corresponding conditional fprintf
statement in check_tfi_usage (AllocTest.cpp) by an equivalent
OSMO_ASSERT.
Sponsored-by: On-Waves ehf
Currently is is rather expensive to get TFI and USF usage per PDCH,
because the TBFs need to be scanned to get that information.
This commit adds corresponding bit sets which get updated by the
attach_tbf/detach_tbf methods of the gprs_rlcmac_pdch class.
Sponsored-by: On-Waves ehf
This commits adds three poll timeout counters
- RLC Assign Timeout
- RLC Ack Timeout
- RLC Release Timeout
to help diagnosing to cause for these events. There seems to be an
increased rate of these when a PDCH is shared by multiple TBFs.
Sponsored-by: On-Waves ehf
In contrast to the slots currently used by existing TBFs, the
reserved slots refer to the time slots that can be used for newly
allocated TBFs without causing conflicts (given that the first common
TS does not change). They correspond to the potential use of the
PDCHs and can be used to achieve a more uniform slot allocation.
This commit adds bit set based methods to GprsMs and gprs_rlcmac_trx
and a counter to gprs_rlcmac_pdch. The current TRX will also be
stored in the MS object.
Sponsored-by: On-Waves ehf
Currently the PDCH object do not know anything about the TBFs using
them. To make the slot allocation load dependant, at least some
numbers are required.
This commit adds TBF counters (one per direction) and the related methods
attach_tbf, detach_tbf, and num_tbfs to gprs_rlcmac_pdch.
Sponsored-by: On-Waves ehf
Currently the code that creates the MS objects with tbf.cpp is
duplicated.
This commit moves the corresponding code into a new method. Since
there is no TLLI available there, the GprsMsStorage::create_ms method
has been refactored into two variants: one with TLLI/direction and
one without.
Sponsored-by: On-Waves ehf
Currently the MS object are created when the TLLI gets known.
Therefore some information (TA, MS class) must be stored in the TBF
itself and is copied to the MS object later on. This would get even
more complex, if the allocation algorithms were extended based on
this scheme.
This commit ensures, that an MS object will always be created on TBF
allocation, even if the TLLI is not yet known. These 'anonymous'
objects are still managed by the MS storage. To avoid dangling
entries without a TLLI there (which cannnot be retrieved anyway), the
timer in the MS objects is not started after all TBF have been
detached, so that they get deleted immediately in that case.
Note that an MS object can still be removed (e.g. by replacement)
from an existing TBF, so tbf->ms() can be NULL.
Ticket: #1794
Sponsored-by: On-Waves ehf
Currently the old TBF (either uplink or downlink) is passed around at
TBF allocation mainly to get information about the MS. To implement
more complex allocation algorithms, the MS object itself will be
needed anyway.
This commit replaces the old_tbf arguments by MS object arguments.
Sponsored-by: On-Waves ehf
This method does not do anything anymore, it's functionality has been
taken over by update_ms.
This commit removes gprs_rlcmac_tbf::update_tlli completely.
Sponsored-by: On-Waves ehf
The I_LEVEL values that are obtained now look suspicious. They do not
seem to be contained in messages recorded via gsmtab.
To help debugging this issue, this commit adds related debug messages
that are generated while the encoded values are taken from the
RLC/MAC messages.
Sponsored-by: On-Waves ehf
This commit extends the pcu_l1_meas structure by MS side measurement
values which are transmitted by PACKET DOWNLINK ACK/NACK and
PACKET RESOURCE REQUEST messages. The encoded values are remapped to
dB respectively % values. The values are stored in the corresponding
MS object (if there is one).
Note that the values are store as (rounded) integers, so some
different encodings are mapped to the same decoded value.
Sponsored-by: On-Waves ehf
Currently only the RSSI value is passed to the upper layers. Other
values like TA and BER which are needed for TA update respectively CS
selection are not propagated.
This commit introduces and passes a struct that contains a set of
measurement values.
Sponsored-by: On-Waves ehf
Jacob Erlbeck