phone-side
/
uboot-mt623x
9
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
uboot-mt623x/include/configs/BUBINGA405EP.h

442 lines
16 KiB
C
Raw Blame History

/*
* (C) Copyright 2000, 2001
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* Debug options */
/*#define __DEBUG_START_FROM_SRAM__ */
/*#define DEBUG 1*/
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_405EP 1 /* This is a PPC405 CPU */
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_BUBINGA405EP 1 /* ...on a BUBINGA405EP board */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
#define CONFIG_NO_SERIAL_EEPROM
/*#undef CONFIG_NO_SERIAL_EEPROM*/
/*----------------------------------------------------------------------------*/
/*----------------------------------------------------------------------------*/
/*----------------------------------------------------------------------------*/
#ifdef CONFIG_NO_SERIAL_EEPROM
/*
!-------------------------------------------------------------------------------
! Defines for entry options.
! Note: Because the 405EP SDRAM controller does not support ECC, ECC DIMMs that
! are plugged in the board will be utilized as non-ECC DIMMs.
!-------------------------------------------------------------------------------
*/
#define AUTO_MEMORY_CONFIG
#define DIMM_READ_ADDR 0xAB
#define DIMM_WRITE_ADDR 0xAA
/*
!-------------------------------------------------------------------------------
! PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI,
! assuming a 33MHz input clock to the 405EP from the C9531.
!-------------------------------------------------------------------------------
*/
#define PLLMR0_DEFAULT PLLMR0_266_133_66
#define PLLMR1_DEFAULT PLLMR1_266_133_66
#endif
/*----------------------------------------------------------------------------*/
/*----------------------------------------------------------------------------*/
/*----------------------------------------------------------------------------*/
/*#define CFG_ENV_IS_IN_FLASH 1*/ /* use FLASH for environment vars */
#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
#ifdef CFG_ENV_IS_IN_NVRAM
#undef CFG_ENV_IS_IN_FLASH
#else
#ifdef CFG_ENV_IS_IN_FLASH
#undef CFG_ENV_IS_IN_NVRAM
#endif
#endif
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#if 1
#define CONFIG_BOOTCOMMAND "" /* autoboot command */
#else
#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
#endif
/* Size (bytes) of interrupt driven serial port buffer.
* Set to 0 to use polling instead of interrupts.
* Setting to 0 will also disable RTS/CTS handshaking.
*/
#if 0
#define CONFIG_SERIAL_SOFTWARE_FIFO 4000
#else
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#endif
#if 0
#define CONFIG_BOOTARGS "root=/dev/nfs " \
"ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 " \
"nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4"
#else
#define CONFIG_BOOTARGS "root=/dev/hda1 " \
"ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0"
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
#define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Bubinga */
/*
#ifndef __DEBUG_START_FROM_SRAM__
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
CFG_CMD_PCI | \
CFG_CMD_IRQ | \
CFG_CMD_KGDB | \
CFG_CMD_DHCP | \
CFG_CMD_DATE | \
CFG_CMD_BEDBUG | \
CFG_CMD_ELF )
#else
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
CFG_CMD_PCI | \
CFG_CMD_IRQ | \
CFG_CMD_KGDB | \
CFG_CMD_DHCP | \
CFG_CMD_DATE | \
CFG_CMD_DATE | \
CFG_CMD_ELF )
#endif
*/
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
CFG_CMD_CACHE | \
CFG_CMD_DATE | \
CFG_CMD_DHCP | \
CFG_CMD_EEPROM | \
CFG_CMD_ELF | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_KGDB | \
CFG_CMD_MII | \
CFG_CMD_NET | \
CFG_CMD_PCI | \
CFG_CMD_PING | \
CFG_CMD_REGINFO | \
CFG_CMD_SDRAM | \
0 )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
/*
* If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
* If CFG_405_UART_ERRATA_59, then UART divisor is 31.
* Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value.
* The Linux BASE_BAUD define should match this configuration.
* baseBaud = cpuClock/(uartDivisor*16)
* If CFG_405_UART_ERRATA_59 and 200MHz CPU clock,
* set Linux BASE_BAUD to 403200.
*/
#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
#define CFG_BASE_BAUD 691200
/* The following table includes the supported baudrates */
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
#if (CONFIG_COMMANDS & CFG_CMD_EEPROM)
#define CFG_I2C_EEPROM_ADDR 0x50 /* I2C boot EEPROM (24C02W) */
#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
#endif
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
#define PCI_HOST_FORCE 1 /* configure as pci host */
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
/* resource configuration */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
#define CFG_PCI_CLASSCODE 0x0600 /* PCI Class Code: bridge/host */
#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
#define CFG_PCI_PTM2LA 0x00000000 /* disabled */
#define CFG_PCI_PTM2MS 0x00000000 /* disabled */
#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* External peripheral base address
*-----------------------------------------------------------------------
*/
#undef CONFIG_IDE_LED /* no led for ide supported */
#undef CONFIG_IDE_RESET /* no reset for ide supported */
#define CFG_KEY_REG_BASE_ADDR 0xF0100000
#define CFG_IR_REG_BASE_ADDR 0xF0200000
#define CFG_FPGA_REG_BASE_ADDR 0xF0300000
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#ifdef __DEBUG_START_FROM_SRAM__
#define CFG_SRAM_BASE 0xFFF80000
#define CFG_FLASH_BASE 0xFFF00000
#define CFG_MONITOR_BASE CFG_SRAM_BASE
#else
#define CFG_SRAM_BASE 0xFFF00000
#define CFG_FLASH_BASE 0xFFF80000
#define CFG_MONITOR_BASE CFG_FLASH_BASE
#endif
/*#define CFG_MONITOR_LEN (200 * 1024) /XXX* Reserve 200 kB for Monitor */
#define CFG_MONITOR_LEN (192 * 1024) /* Reserve 200 kB for Monitor */
#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
/* BEG ENVIRONNEMENT FLASH */
#ifdef CFG_ENV_IS_IN_FLASH
#define CFG_ENV_OFFSET 0x00050000 /* Offset of Environment Sector */
#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
#endif
/* END ENVIRONNEMENT FLASH */
/*-----------------------------------------------------------------------
* NVRAM organization
*/
#define CFG_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
#define CFG_NVRAM_SIZE 0x1ff8 /* NVRAM size */
#ifdef CFG_ENV_IS_IN_NVRAM
#define CFG_ENV_SIZE 0x0ff8 /* Size of Environment vars */
#define CFG_ENV_ADDR \
(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */
#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_DCACHE_SIZE 16384 /* For IBM 405EP CPU */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Init Memory Controller:
*
* BR0/1 and OR0/1 (FLASH)
*/
#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
#define CFG_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CFG_OCM_DATA_ADDR 0xF8000000
#define CFG_OCM_DATA_SIZE 0x1000
#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */
#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*/
/* Memory Bank 0 (Flash/SRAM) initialization */
#define CFG_EBC_PB0AP 0x04006000
#define CFG_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */
/* Memory Bank 1 (NVRAM/RTC) initialization */
#define CFG_EBC_PB1AP 0x04041000
#define CFG_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
/* Memory Bank 2 (not used) initialization */
#define CFG_EBC_PB2AP 0x00000000
#define CFG_EBC_PB2CR 0x00000000
/* Memory Bank 2 (not used) initialization */
#define CFG_EBC_PB3AP 0x00000000
#define CFG_EBC_PB3CR 0x00000000
/* Memory Bank 4 (FPGA regs) initialization */
#define CFG_EBC_PB4AP 0x01815000
#define CFG_EBC_PB4CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
/*-----------------------------------------------------------------------
* Definitions for Serial Presence Detect EEPROM address
* (to get SDRAM settings)
*/
#define SPD_EEPROM_ADDRESS 0x55
/*-----------------------------------------------------------------------
* Definitions for GPIO setup (PPC405EP specific)
*
* GPIO0[0] - External Bus Controller BLAST output
* GPIO0[1-9] - Instruction trace outputs
* GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
* GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs
* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
* GPIO0[24-27] - UART0 control signal inputs/outputs
* GPIO0[28-29] - UART1 data signal input/output
* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
*/
#define CFG_GPIO0_OSRH 0x55555555
#define CFG_GPIO0_OSRL 0x40000110
#define CFG_GPIO0_ISR1H 0x00000000
#define CFG_GPIO0_ISR1L 0x15555445
#define CFG_GPIO0_TSRH 0x00000000
#define CFG_GPIO0_TSRL 0x00000000
#define CFG_GPIO0_TCR 0xFFFF8014
/*-----------------------------------------------------------------------
* Some BUBINGA stuff...
*/
#define NVRAM_BASE 0xF0000000
#define FPGA_REG0 0xF0300000 /* FPGA Reg 0 */
#define FPGA_REG1 0xF0300001 /* FPGA Reg 1 */
#define NVRVFY1 0x4f532d4f /* used to determine if state data in */
#define NVRVFY2 0x50454e00 /* NVRAM initialized (ascii for OS-OPEN)*/
#define FPGA_REG0_F_RANGE 0x80 /* SDRAM PLL freq range */
#define FPGA_REG0_EXT_INT_DIS 0x20 /* External interface disable */
#define FPGA_REG0_LED_MASK 0x07 /* Board LEDs DS9, DS10, and DS11 */
#define FPGA_REG0_LED0 0x04 /* Turn on LED0 */
#define FPGA_REG0_LED1 0x02 /* Turn on LED1 */
#define FPGA_REG0_LED2 0x01 /* Turn on LED2 */
#define FPGA_REG1_SSPEC_DIS 0x80 /* C9531 Spread Spectrum disabled */
#define FPGA_REG1_OFFBD_PCICLK 0x40 /* Onboard PCI clock selected */
#define FPGA_REG1_CLOCK_MASK 0x30 /* Mask for C9531 output freq select */
#define FPGA_REG1_CLOCK_BIT_SHIFT 4
#define FPGA_REG1_PCI_INT_ARB 0x08 /* PCI Internal arbiter selected */
#define FPGA_REG1_PCI_FREQ 0x04 /* PCI Frequency select */
#define FPGA_REG1_OFFB_FLASH 0x02 /* Off board flash */
#define FPGA_REG1_SRAM_BOOT 0x01 /* SRAM at 0xFFF80000 not Flash */
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#endif /* __CONFIG_H */
Reference in New Issue View Git Blame Copy Permalink