Since the vast majority of GPIO I2C implementations behave the same way,
support the common GPIO framework with default settings.
This adds two new defines CONFIG_SOFT_I2C_GPIO_{SCL,SDA} so that boards
which want GPIO I2C support need only define these.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
* add's a warning to all files, which need update to new SoC access
* convert common files in cpu/../at91 and a lot of drivers to use
c stucture SoC access
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
New default, weak i2c_get_bus_speed() and i2c_set_bus_speed() functions
replace a number of architecture-specific implementations.
Also, providing default functions will allow all boards to enable
CONFIG_I2C_CMD_TREE. This was previously not possible since the
tree-form of the i2c command provides the ability to display and modify
the i2c bus speed which requires i2c_[set|get]_bus_speed() to be
present.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This patch fix the compiler/linker errors
common/cmd_i2c.c:1252: undefined reference to `i2c_get_bus_speed'
common/cmd_i2c.c:1256: undefined reference to `i2c_set_bus_speed'
if board use CONFIG_I2C_CMD_TREE and CONFIG_I2C_MULTI_BUS is not
uesd/undef (wrong define order)
and
removes additional empty lines
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
This patch adds support for the kmsupx4 board from Keymile,
based on a Freescale MPC852T CPU
- serial console on SMC1
- 32 MB SDRAM
- 32 MB NOR Flash
- Ethernet over SCC3
- I2C Bitbang
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds a #define to optionally change the behaviour of
i2c_read() in soft_i2c.c to send an I2C repeated start instead of a
stop-start between sending the device address pointer write and
reading back the data. The current behaviour is retained as the
default.
While most devices will work either way, I have a smart battery(*)
that requires repeated start, and someone at some point found a
device that required a stop-start.
(*) http://www.inspired-energy.com/Standard_Products/NL2054/NL2054%20Rev1.0%20Data%20Sheet.pdf
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
All implementations of the functions i2c_reg_read() and
i2c_reg_write() are identical. We can save space and simplify the
code by converting these functions into inlines and putting them in
i2c.h.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-By: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch fixes the following warnings, when using
the soft_i2c driver using no CPU pins on MPC82xx or MPC8xx
systems:
soft_i2c.c: In function 'send_reset':
soft_i2c.c:93: warning: unused variable 'immr'
soft_i2c.c: In function 'send_start':
soft_i2c.c:124: warning: unused variable 'immr'
soft_i2c.c: In function 'send_stop':
soft_i2c.c:146: warning: unused variable 'immr'
soft_i2c.c: In function 'send_ack':
soft_i2c.c:171: warning: unused variable 'immr'
soft_i2c.c: In function 'write_byte':
soft_i2c.c:196: warning: unused variable 'immr'
soft_i2c.c: In function 'read_byte':
soft_i2c.c:244: warning: unused variable 'immr'
Signed-off-by: Heiko Schocher <hs@denx.de>
Mike Frysinger