We should check the return of usb_new_device() so that if no USB device is
found, we print out the right message rather than always saying "new usb
device found".
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
With this patch the USB related connection speed output ("usb tree" command and
debug output) is now high-speed enabled.
This patch also fixes a compilation warning when debugging is enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Rather than forcing people to define a custom "LITTLEENDIAN", just use the
__LITTLE_ENDIAN one from the Linux byteorder headers that every arch is
already setting up.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The SanDisk Corporation U3 Cruzer Micro 1/4GB Flash Drive 000016244373FFB4
does not like to be reset, so check for it.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch populates the 'priv' field of the USB keyboard device_t
structure. The 'priv' field is populated with the address of the
'struct usb_device' structure that represents the USB device.
The 'priv' field can then be used in the 'usb_event_poll' function to
determine the USB device that requires to be polled. An
example of its usage in 'usb_event_poll' function is as below.
device_t *dev;
struct usb_device *usb_kbd_dev;
<snip>
dev = device_get_by_name("usbkbd");
usb_kbd_dev = (struct usb_device *)dev->priv;
iface = &usb_kbd_dev->config.if_desc[0];
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
USB changes the speed according to the port status
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The BF53x/BF56x parts do not have an on-chip ROM to boot LDRs out of
arbitrary memory locations, so implement a basic one in software.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that real documentation has been released for the OTP interface and
the on-chip ROM wrt writing/timings, implement support for reading/writing
as well as dumping/locking.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin JTAG has the ability to pass data via a back-channel without
halting the processor. Utilize that channel to emulate a console.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Rather than have the board code initialize SATA automatically during boot,
make the user manually run "sata init". This brings the SATA subsystem in
line with common U-Boot policy.
Rather than having a dedicated weak function "is_sata_supported", people
can override sata_initialize() to do their weird board stuff. Then they
can call the actual __sata_initialize().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch fixes a bug (?) introduced after inclusion of the new
JFFS2 code.
When not using CONFIG_JFFS2_CMDLINE, the code in cmd_jffs2.c doesn't
fill in part->sector_size (keeping it as 0), but a correct value is
needed by the code in jffs2_1pass.c. This causes all JFFS2 accesses
to be in the same place of the memory, what obviously means
impossibility to use the JFFS2 partition.
This problem is fixed in this patch by including sector size
calculation in non-CONFIG_JFFS2_CMDLINE mtdparts_init variant.
Signed-off-by: Tomasz Figa <tomasz.figa_at_gmail.com>
Rather than special casing each environment type for enabling the saveenv
command, have them all behave the same. This avoids bitrot as new env
sources are added/removed.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
U-Boot's gunzip() function does not handle the return code
of zlib's inflate() function correctly. gunzip() is implemented
to uncompress all input data in one run. So the correct return
code for the good case is Z_STREAM_END. In case of insufficient
output buffer memory inflate returns Z_OK. For gunzip() this
is an error.
It also makes sense to me to call inflateEnd() also in case
of an error.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
The iteration limit is passed to mtest as a fourth parameter:
[start [end [pattern [iterations]]]]
If no fourth parameter is supplied, there is no iteration limit and the
test will loop forever.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Support bootdelay=0 in abortboot for the CONFIG_AUTOBOOT_KEYED case
similar to the CONFIG_ZERO_BOOTDELAY_CHECK support for the
!CONFIG_AUTOBOOT_KEYED case.
Do this by reversing the loop so we do at least one iteration before
checking for timeout.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Error with CONFIG_NAND_LEGACY in common/cmd_nand.c:
With current code "nand read.jffs2s" (read and skip bad blocks) is always interpreted as
"nand read.jffs2" (read and fill bad blocks with 0xff). This is because ".jffs2" is
tested before ".jffs2s" and only the first two characters are compared.
Correction:
Test for ".jffs2s" first and compare the first 7 characters.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Enable nand lock, unlock and status of lock feature.
Not every device and platform requires this, hence,
it is under define for CONFIG_CMD_NAND_LOCK_UNLOCK
Nand unlock and status operate on block boundary instead
of page boundary. Details in:
http://www.micron.com/products/partdetail?part=MT29C2G24MAKLAJG-6%20IT
Intial solution provided by Vikram Pandita <vikram.pandita@ti.com>
Includes preliminary suggestions from Scott Wood
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Update OneNAND command to support bad block awareness.
Also change the OneNAND command style to better match the
NAND version.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
The code in fdt_resize() to extend the fdt size to end on a page boundary
is wrong for fdt's not located at an address aligned on a page boundary.
What's even worse, the code would make actualsize shrink rather than grow
if (blob & 0xfff) was bigger than the amount of padding added by ALIGN(),
causing fdt_add_mem_rsv to fail.
Fix it by aligning end address (blob + size) to a page boundary instead.
For aligned fdt's this is equivalent to what we had before.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
If both CONFIG_ENV_SECT_SIZE and CONFIG_ENV_SIZE are defined, and the sect
size is larger than the env size, then it means the env is embedded in a
block. So we have to save/restore the part of the sector which is not the
environment. Previously, saving the environment in SPI flash in this
setup would probably brick the board as the rest of the sector tends to
contain actual U-Boot data/code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
FDT support is used for both FIT style images and for architectures
that can pass a fdt blob to an OS (ppc, m68k, sparc).
For other architectures and boards which do not pass a fdt blob to an
OS but want to use the new uImage format, we just need FIT support.
Now we can have the 4 following configurations :
1) FIT only CONFIG_FIT
2) fdt blob only CONFIG_OF_LIBFDT
3) both CONFIG_OF_LIBFDT & CONFIG_FIT
4) none none
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
With this patch we set the type back to NONE upon failing UBI partition
initialization. Otherwise further calls to the UBI subsystem would try
to really access the non-existing UBI partition.
Thanks to Michael Lawnick for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
With this patch now, the user can call "ubi part" multiple times to
re-connect the UBI device to another MTD partition.
Signed-off-by: Stefan Roese <sr@denx.de>
rename devices_init () in common/jffs2.c to
jffs2_devices_init (), because there is also a
devices_init () in common/devices.c.
Signed-off-by: Heiko Schocher <hs@denx.de>
Modifications to support console multiplexing. This is controlled using
CONFIG_SYS_CONSOLE_MUX in the board configuration file.
This allows a user to specify multiple console devices in the environment
with a command like this: setenv stdin serial,nc. As a result, the user can
enter text on both the serial and netconsole interfaces.
All devices - stdin, stdout and stderr - can be set in this manner.
1) common/iomux.c and include/iomux.h contain the environment setting
implementation.
2) doc/README.iomux contains a somewhat more detailed description.
3) The implementation in (1) is called from common/cmd_nvedit.c to
handle setenv and from common/console.c to handle initialization of
input/output devices at boot time.
4) common/console.c also contains the code needed to poll multiple console
devices for input and send output to all devices registered for output.
5) include/common.h includes iomux.h and common/Makefile generates iomux.o
when CONFIG_SYS_CONSOLE_MUX is set.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
When running `strings` on really long strings, the stack tends to get
smashed due to printf(). Switch to puts() instead since we're only passing
the data through.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
- fix size too small by one in sprintf
- changed old (pre 2004) device name ibmEmac to emac
- boot device may be overriden in board config
- servername may be defined in board config
- additional parameters may be defined in board config
- fixed some line wrappings
- replaced redundant MAX define by max
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
When CONFIG_SYS_HUSH_PARSER is defined network download
commands with 1 argument in the format 'tftp "/path/file"'
do not work as expected. The hush command parser strips
the quotes from "/path/file" which causes the network
commands to interpret "/path/file" as an address
instead of the intended filename.
The previous check for a leading quote in netboot_common()
was replaced with a check which ensures only valid
numbers are treated as addresses.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Without this patch "saveenv" crashes when MTD partitions are enabled (e.g.
for use in UBI) via CONFIG_MTD_PARTITIONS.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Wolfgang Denk