Remove and fix needless and destructive operations with tx/rx_req.
1) 'req' in rx_complete is always not NULL and always equals to rx_req
2) Free allocated tx_req if rx_req allocation has failed
3) Do not zero out tx/rx_req in usb_eth_init, leave this for
eth_reset_config which will be called at the next use of usb0
4) Additional check in usb_eth_recv is not required
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
This fixes TIMEOUT with my Kingston 32GB USB3.0 flashdrive, which I experienced
on my PXA270 (USB 1.1) Vpac270 board.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
The pl01x serial driver was lacking the code to switch baudrates from the
command line. Fixed by simply saving the new baudrate and calling
serial_init() again. Also fixed CamelCase variables, I/O accessors and
comment style.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
mvsata_ide_initialize_port(): adjust init sequence (SStatus
should be checked only after all writes to SControl) and
return success/failure to ide_preinit().
Also, as some tests showed init durations in the hundreds
of us, raise the time-out to 01 ms to be on the safe side.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
This allows for arbitrarily long manufacturer ids following the JEDEC
standard of 0x7f continuation bytes. It also makes adding new entries
easier as it's just one element in an array. The downside is that it
increases code size a bit, but we're talking ~50 bytes.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Split the display command into generic interface and hardware-specific
realization for PDSP188x LED display found on hmi1001 and manroland
boards. Simple interface for LED displays is defined in
include/led-display.h and described in doc/README.LED_display.
Driver-specific implementation was moved into drivers/misc/pdsp188x.c
file (enabled with CONFIG_PDSP188x set).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
When a CFI flash chip could not be detected an error message similar to
the following would be printed on bootup:
FLASH: ## Unknown FLASH on Bank 1 - Size = 0x01000000 = 0 MB
The printf incorrectly converted the flash size into megabytes. This
patch fixes the printing of the flash size in megabytes:
FLASH: ## Unknown FLASH on Bank 1 - Size = 0x01000000 = 16 MB
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add smc_write_hwaddr() to set mac address.
Clear dev before use.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch proposes to migrate the davinci_emac driver to using the
eth_device->write_hwaddr function pointer as suggested by Ben Warren.
All the davinci boards had the behaviour, prior to this patch, of
sync'ing the environment variable enetaddr with the MAC address read
from non-volatile storage on boot -- when the two locations disagreed,
the environment variable value took precendence. This patch keeps the
same behaviour but lets eth_initialize take care of it.
This patch refactors davinci_emac setup in the boards so that the MAC
address is read from non-volatile storage into the environment variable
and then the environment variable value is use in eth_intialize. The
only exception is the direct call to davinci_eth_set_mac_addr made by
the da830evm board init which was changed into an assignment of the
enetaddr field.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Tested-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Emaclite was using old net api that's why
this patch move emaclite to NET_MULTI api.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Some boards need their board-specific PHY quirks to be called
to PHY to work normally. As mpc5xxx_fec driver uses on demand
PHY initialization and can even reinit PHY during normal operation
we can't count on reset_phy() call from arch/<arch>/lib/board.c
(it is most likely called _before_ we init the PHY from the
driver) so we need to add call to reset_phy() directly in the
driver.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Some return values pretended correct pass. This patch changes them according
to README.drivers.net. This patch changes e.g. command 'dhcp' to stop after
errorneous autonegotiation.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch increases timeout for autonegotiation from 1 second to 3 seconds.
Some boards (e.g. at91rm9200ek) did not negotiate within 1 second.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
V3: further refinements:
- use priv member instead of container method
- allow setting of MAC address by write_hwaddr method
- avoid shutting down link between commands
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Instead of always performing an autoneg, check if the PHY
already has a link and if it matches one of the requested
modes. Initially only 100MbFD is optimized this way.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This udelay looks bogus and doesn't help my board.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
uec_init() adds an udelay(100000) even though
the PHY status read went well, don't do that.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch is required before the upcoming new enc28j60 driver
using SPI framework patch can be applied:
- Move legacy enc28j60.c to enc28j60_lpc2292.c.
- Change Makefile and the two affected boards' definition files.
Tested with ./MAKEALL ARM7 that both boards still compile.
Signed-off-by: Reinhard Meyer<info@emk-elektronik.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds the Numonyx manufacturer code (0x20) to
onenand manufacturers.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Consolidate some code in mtd_get_len_incl_bad(), and fix a condition
where a valid partition could be reported as truncated if it has a
good block at the end of the device (unlikely, since the BBT is usually
there).
Fix mid-block declarations in net_part_size().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Ben Gardiner <bengardiner@nanometrics.ca>
The logic to 'spread' mtd partitions needs to calculate the length in
the mtd device, including bad blocks.
This patch introduces a new function, mtd_get_len_incl_bad that can
return both the length including bad blocks and whether that length
was truncated on the device. This new function will be used by the
mtdparts spread command later in this series. The definition of the
function is #ifdef'd out in configurations that do not use the new
'mtdparts spread' command.
Signed-off-by: Ben Gardiner<bengardiner@nanometrics.ca>
CC: Scott Wood <scottwood@freescale.com>
Get rid of the several "#if 0" sections that were keeping around Linux
code that isn't relevant to U-Boot. Besides cluttering the code, these
sections make tracking upstream changes harder, rather than easier.
It's easy to discard obviously irrelevant diff hunks that patch rejects,
but it's not as easy to notice hunks that apply cleanly to the #if 0
section, but *are* relevant to U-Boot and require modification elsewhere.
Also remove suspend/resume, as this is not applicable to U-Boot. Removal
saves 232 bytes on powerpc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
A while back, in http://lists.denx.de/pipermail/u-boot/2009-June/054428.html,
Michele De Candia posted a patch to not count bad blocks toward the
requested size to be erased. This is desireable when you're passing in
something like $filesize, but not when you're trying to erase a partition.
Thus, a .spread subcommand (named for consistency with
http://lists.denx.de/pipermail/u-boot/2010-August/075163.html) is introduced
to make explicit the user's desire to erase for a given amount of data,
rather than to erase a specific region of the chip.
While passing $filesize to "nand erase" is useful, accidentally passing
something like $fliesize currently produces quite unpleasant results, as the
variable evaluates to nothing and U-Boot assumes that you want to erase
the entire rest of the chip/partition. To improve the safety of the
erase command, require the user to make explicit their intentions by
using a .part or .chip subcommand. This is an incompatible user interface
change, but keeping compatibility would eliminate the safety gain, and IMHO
it's worth it.
While touching nand_erase_opts(), make it accept 64-bit offsets and sizes,
fix the percentage display when erase length is rounded up, eliminate
an inconsistent warning about rounding up the erase length which only
happened when the length was less than one block (rounding up for $filesize
is normal operation), and add a diagnostic if there's an attempt to erase
beginning at a non-block boundary.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
The underlying code in nand_base.c already supports non-page-aligned reads
and writes, but the block-skipping wrapper code did not.
With block skipping, an unaligned start address is not useful since you
really want to be starting at the beginning of a partition -- or at least
that's where you want to start checking for blocks to skip, but we don't
(yet) support that. So we still require the start address to be aligned.
An unaligned length, though, is useful for passing $filesize to the
read/write command, and handling it does not complicate block skipping.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
This patch introduces an extra mask-field in spansion_spi_flash_params
to support flash chips with 1-byte extended ID (like the S25FL032P).
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The spansion_erase currently only works when the sector size is 64KB.
cmd[1] should contain the higher 8 bit of the 24 bit address of the
sector to be erased. Currently it is holding the sector index to be
erased which happens to be the same thing when the sector size is
64KB.
Signed-off-by: Marc-Andre Hebert <marc-andre.hebert@humanware.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fix bug where signed data was processed as unsigned. The bug previously
resulted in negative temperature readings wrapping around, eg -10 became
245.
Signed-off-by: Jeff Dischler <jdischler@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Poll the ds1621 NV Memory Busy bit instead of waiting a static amount of
time for register writes.
Also add config retister bit defines.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Adds support for Winbond's W25Q64 SPI flash. These devices are used on
(among others) Xilinx' SP601 and SP605 Spartan-6 evaluation boards.
Tested with "sf" commands.
Signed-off-by: Graeme Smecher <graeme.smecher@mail.mcgill.ca>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch replaces the unnecessary waiting in at91emac_read() and
at91emac_write() by checking the IDLE flag.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch also removes conditional nameing of at91_emac driver whether it's
connection to PHY is RMII or MII.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Simplify the command setup and status checking steps, and add a proper
timeout to the status polling code to avoid possible infinite hangs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This moves the last piece from the old spi_flash driver to the new SPI
framework -- optional DMA RX support. This typically cuts speeds by ~40%
at the cost of additional ~300 bytes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The actual SPI driver for i.MX31 and i.MX51 controller
use a wrong byte ordering, because it is supposed
to work only with Freescale's devices, as the Power
Controllers (PMIC). The driver is not suitable for
general purposes, because the buffers passed to spi_xfer
must be 32-bit aligned, as it is used mainly to send
integer to PMIC devices.
The patch drops any kind of limitation and makes the
driver useful with devices controlled sending commands
composed by single bytes (or by a odd number of bytes), such as
spi flash, sensor, etc.
Because the byte ordering is changed,
any current driver using this controller must be adapted, too.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The handling of the SPI_CPOL bit inside the SPI
driver was wrong. As reported by the manual,
the meaning of the SSPOL inside the
configuration register is the same as reported
by SPI specification (0 if low in idle, 1 is high
on idle). The driver inverts this logic.
Because this patch sets the logic as specified, it is required
to clear the CPOL bit in the configuration file to adapt
to the correct logic.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: David Jander <david.jander@protonic.nl>
The patch adds support for setting gpios to the
MX51 processor and change name to the corresponding
functions for MX31. In this way, it is possible to get rid
of nasty #ifdef switches related to the processor type.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Commit 2ee951ba (UBI: Enable re-initializing of the "ubi part" command)
reset mtd_devs in ubi_exit() but missed ubi_init()'s failure path.
Signed-off-by: Karl Beldan <karl.beldan@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
CONFIG_UART1_CONSOLE was a PPC4xx specific implementation and is now
removed since the move from the 4xx UART driver to the common NS16550
UART driver. Let's remove all references to this define now.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch starts a bit PPC4xx header cleanup. First patch mostly
touches PPC440 files. A later patch will touch the PPC405 files as well.
This cleanup is done by creating header files for all SoC versions and
moving the SoC specific defines into these special headers. This way the
common header ppc405.h and ppc440.h can be cleaned up finally.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves some ppc4xx related headers from the common include
directory (include/) to the powerpc specific one
(arch/powerpc/include/asm/). This way to common include directory is not
so cluttered with files.
Signed-off-by: Stefan Roese <sr@denx.de>
Linux uses an offset of 8 to switch from hardware cs to a gpio cs,
so have u-boot use the same value. Also make sure it is public
for boards to access.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add support for 4bpp bitmaps, currently only for GDF_32BIT_X888RGB
frame buffer format.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fixes most of checkpatch warnings and errors in USB gadget stack.
The most frequently encountered problems are:
1) "(foo*)", "foo * bar", "foo* bar"
2) C99 // comments
3) No spaces before/after/around '?', ':', '=', '==', ',', '&', '('
4) Spaces before '['
5) Spaces between function names and '('
6) Block braces in wrong places
7) Spaces before tabs
8) Macros with complex values not enclosed in parenthesis
9) Multiline comments start just after /*
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
The patch removes an endless loop in the usb_eth_send
if the tx_complete is not called before going
in the loop. The driver interrupt routine is called
allowing the driver to check if the TX is completed.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The buffer for the status request must be word aligned
because it is accessed with 32 bit pointer in the
eth_status_complete function.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The patch is based on commit bb9496c6f7e853e5d4edd5397c9d45f1968d623c
(done by Julia Lawall <julia@diku.dk>) from linux-2.6.git.
Since num is unsigned, it would seem better to use simple_strtoul that
simple_strtol.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Fix potential oops on rare error path.
The patch is based on commit e7b13ec9235b9fded90f826ceeb8c34548631351
(done by David Brownell <david-b@pacbell.net>) from linux-2.6.git.
Description of the issue taken from linux kernel bugzilla:
(https://bugzilla.kernel.org/show_bug.cgi?id=9594)
The potential error can be tracked down as follows:
(1) line 807: let the second conjunct on the "if" statment be false
meaning "dev->status_ep" is null. This means the "if" evaluates
to false.
follow thru the code until...
(2) line 808: usb_ep_disable(dev->status_ep) passes in a null argument,
however "usb_ep_disable" cannot handle that:
(from include/linux/usb/gadget.h)
191 static inline int
192 usb_ep_disable (struct usb_ep *ep)
193 {
194 return ep->ops->disable (ep);
195 }
--
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Fix possible oops on stat_req->buf initialization and fix ep0 and
status_ep confusion (last one is just intended for stat_req keeping).
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Fix in_ep and out_ep confusion (rx_req was allocated from out_ep, not
from in_ep) and add lost dev->req freeing.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Add lost 'qmult' definition for High Speed devices and make it
configurable through CONFIG_USB_ETH_QMULT.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Prohibit simultaneous usage of both old and new gadget stacks and
allow UDC drivers to be dependent on CONFIG_USB_ETHER.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
The MUSB_TXCSR_MODE register setting isn't supported on Blackfin musb
parts, so stub it out to 0. This matches Linux behavior.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the defines are moved to header files we don't need this
conditional compilation any more. Remove it.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch simplifies the use of CONFIG_SYS_MAX_FLASH_BANKS_DETECT. By
moving these optional variables and defines into the common code, board
specific code is minimized. Currently only the following board use
this feature:
APC405, IDS8247, TQM834x
And IDS8247 doesn't seem to really need this feature, since its not
updating the bank number variable at all. So this patch removes the
definition of CONFIG_SYS_MAX_FLASH_BANKS_DETECT from this board port.
This new framework will be used by the upcoming lwmon5 update as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
cfi_flash_bank_addr(int bank_nr) returns the base addresses of the
requested bank. Introducing this weak default enables boards to override
this functions with a board specific version when required.
This feature will be used in the lwmon5 board update, supporting runtime
detection of 2 board revisions with different flash layouts.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes an unecessary check in the return statement. This is
not needed, since "info" is initializes to NULL. And "info" will not be
written to again, if the flash address is not found.
Additionally "info" is not initialized to "0" but to "NULL".
Signed-off-by: Stefan Roese <sr@denx.de>
Recent changes caused that the HMI10 board now is included in the
boards built by MAKEALL, which revealed that compilation for this
board has been broken for a long time:
ps2ser.c: In function 'ps2ser_init':
ps2ser.c:155: error: 'UART_LCR' undeclared (first use in this function)
ps2ser.c:155: error: (Each undeclared identifier is reported only once
ps2ser.c:155: error: for each function it appears in.)
ps2ser.c:156: error: 'UART_DLL' undeclared (first use in this function)
ps2ser.c:157: error: 'UART_DLM' undeclared (first use in this function)
ps2ser.c:159: error: 'UART_IER' undeclared (first use in this function)
ps2ser.c:160: error: 'UART_MCR' undeclared (first use in this function)
ps2ser.c:161: error: 'UART_FCR' undeclared (first use in this function)
ps2ser.c:162: error: 'UART_FCR_ENABLE_FIFO' undeclared (first use in this function)
ps2ser.c:166: error: 'UART_LSR' undeclared (first use in this function)
ps2ser.c: In function 'ps2ser_putc':
ps2ser.c:198: error: 'UART_LSR' undeclared (first use in this function)
ps2ser.c:200: error: 'UART_TX' undeclared (first use in this function)
ps2ser.c: In function 'ps2ser_getc_hw':
ps2ser.c:224: error: 'UART_LSR' undeclared (first use in this function)
ps2ser.c:225: error: 'UART_RX' undeclared (first use in this function)
ps2ser.c: In function 'ps2ser_interrupt':
ps2ser.c:293: error: 'UART_IIR' undeclared (first use in this function)
The board is orphaned, and AFAICT has reached EOL.
Drop support for it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit d2bf29e3 caused a number of compiler warnings:
mmc.c: In function 'mmc_bwrite':
mmc.c:97: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
mmc.c:97: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'lbaint_t'
mmc.c: In function 'mmc_bread':
mmc.c:229: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
mmc.c:229: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'lbaint_t'
Fix these.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Lei Wen <leiwen@marvell.com>
The CURSOR_ON, CURSOR_OFF, and CURSOR_SET macros are defined incorrectly. If
cursor support is disabled, then these macros are defined to nothing, but
then they are used like this:
if (console_col < CONSOLE_COLS)
CURSOR_OFF
console_row++;
which was compiled like this:
if (console_col < CONSOLE_COLS)
console_row++;
This is obviously not what was intended.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Due to a register glitch (result code <4 might show up right after the
start-calculation-bit was set), make sure the ECC has really started.
See 1c3275b656045aff9a75bb2c9f3251af1043ebb3 in the kernel.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
The Blackfin implementation of musb has a TXCOUNT register that needs to
be programmed when transmitting data.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This printk was added recently and results in ugly output on systems
with no NAND:
NAND: nand_get_flash_type: unknown NAND device: Manufacturer ID: 0x00, Chip ID: 0x00 0 MiB
instead of:
NAND: 0 MiB
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds a function to allow one to easily set the target
voltage for the TWL4030 regulators. It also modifies the existing
code to use this new function. Applicable definitions are moved
out of the driver file and into the header file so that they are
generally accessible
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This rewrite of the mvtwsi driver is 25% smaller and much
faster and simpler than the previous code.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar<prafulla@marvell.com>
Acked-by: Heiko Schocher<hs@denx.de>
This driver is not kirkwood-specific and can also be used
e.g. by orion5x. Rename to a SoC-neutral name.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar<prafulla@marvell.com>
Acked-by: Heiko Schocher<hs@denx.de>
Because of peripheral devices can select clock sources,
separate the peripheral clocks. (pwm, uart and so on)
It just return the pclk at s5pc1xx SoC,
but s5pc210 SoC must be calculated by own clock register setting.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Make the header guard to be generic to stop conflicting with
omap2 i2c header file arch/arm/include/asm/arch-omap24xx/i2c.h
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Heiko <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Wolfang Denk <wd@denx.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
I have "ported" U-boot to a in house made board with Numonyx Axcell P33/P30
256-Mbit 65nm flash chips.
After some time :( searching for bugs in our board or soft, we have
discovered that those chips have a small but annoying bug, documented in
"Numonyx Axcell P33/P30 256-Mbit Specification Update"
It states :
When customer uses [...] block unlock, the block lock status might be
altered inadvertently. Lock status might be set to either 01h or 03h
unexpectedly (00h as expected data), which leads to program/erase failure
on certain blocks.
A working workaround is given, which I have applied and tested with success :
Workaround: If the interval between 60h and its subsequent command
can be guaranteed within 20us, Option I is recommended,
otherwise Option II (involves hardware) should be selected.
Option I: The table below lists the detail command sequences:
Command
Data bus Address bus Remarks
Sequence
1 90h Block Address
Read Lock Status
2 Read Block Address + 02h
(2)(3) (1)
3 60h Block Address
(2)(3) (1) Lock/Unlock/RCR Configuration
4 D0h/01h/03h Block Address
Notes:
(1) Block Address refers to RCR configuration data only when the 60h
command sequence is used to set RCR register combined with 03h
subsequent command.
(2) For the third and fourth command sequences, the Block Address must
be the same.
(3) The interval between 60h command and its subsequent D0h/01h/2Fh/03h
commands should be less than 20us.
And here is a log comparison of a simple (destructive) flash test without
and with the workaround.
diff without-numonyx-workaround.log with-numonyx-workaround.log
-U-Boot 2010.06-00696-g22b002c-dirty (Aug 16 2010 - 15:07:47)
+U-Boot 2010.06-00696-g22b002c-dirty (Aug 16 2010 - 15:25:19)
CPU: Freescale MCF5484
CPU CLK 200 MHz BUS CLK 100 MHz
Board: Macq Electronique ME2060
I2C: ready
DRAM: 64 MiB
FLASH: 32 MiB
In: serial
Out: serial
Err: serial
Net: FEC0, FEC1
-> flinfo
Bank # 1: CFI conformant FLASH (16 x 16) Size: 32 MB in 259 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x8922
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 5 ms, buffer size: 1024 bytes
Sector Start Addresses:
FE000000 RO FE008000 RO FE010000 RO FE018000 RO FE020000 RO
FE040000 RO FE060000 RO FE080000 RO FE0A0000 RO FE0C0000 RO
...
FFF80000 RO FFFA0000 RO FFFC0000 RO FFFE0000 RO
-> protect off all
Un-Protect Flash Bank # 1
................... done
-> erase all
Erase Flash Bank # 1
................... done
-> cp.b 1000000 fe000000 2000000
-Copy to Flash... Flash not Erased
+Copy to Flash... done
->
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch does the following:
- Extract code to detect if sector is erased into function
sector_erased().
- Because of this, we don't have variable declarations inside the
sector loop in flash_print_info()
- Change "return" to "break" in the "if (ctrlc()) statement:
This fixes a problem with the resulting output. Before this
patch the output was:
Sector Start Addresses:
FC000000 FC020000 FC040000 =>
With this patch it is now:
Sector Start Addresses:
FC000000 FC020000 FC040000
=>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Fix reading and printing of CFI flashes 16-bit devices identifiers
Nowadays CFI flashes have a 16-bit device identifier. U-boot still
print them and read them as if they were only 8-bit wide. Fix that.
Before:
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x1B
After:
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x881B
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is intended to prepare the other S5P SoC. (s5pc210)
If use SoC specific defines then can't share with other SoC.
So, make the accessor functions for access the base address by common way.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The OMAP3 block read function is not following API and always returning
1 instead of read block count, fix it. Also to simplify code, merge it
with with a helper function, which was only called from the block read
function.
After this patch ext2 filesystem can be used properly.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Make driver local variables and functions static and
remove them from the arch header.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
AM35x supports only 32bit read operations so we need to have
workaround for 8bit and 16bit read operations.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
This patch adds support for the display controller in
the MB86R0x SoCs.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Commit 6e37b1a3a25004d3df5867de49fff6b3fc9c4f04 modifies several net calls
to take a (const char *) parameter instead of (char *), but in some cases
the modified functions call other functions taking (char *). The end result
is warnings about discarding the const qualifier.
This patch fixes these other function signatures.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The driver name does not need to be writable, so constify it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
continuation of commit 2ecc2262d66a286e3aac79005bcb5f461312dea8
"net ppc: fix ethernet device names with spaces" (currently in
u-boot-net.git) for QE based parts.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
since commit 1384f3bb8a ethernet names
with spaces drop a
Warning: eth device name has a space!
message. This patch fix it for:
- "FEC ETHERNET" devices found on
mpc512x, mpc5xxx, mpc8xx and mpc8220 boards.
renamed to "FEC".
- "SCC ETHERNET" devices found on
mpc8xx, mpc82xx based boards. Renamed to "SCC".
- "HDLC ETHERNET" devices found on mpc8xx boards
Renamed to "HDLC"
- "FCC ETHERNET" devices found on mpc8260 and mpc85xx based
boards. Renamed to "FCC"
Tested on the kup4k board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
After discussion on the ML it is suggested to drop unrequired
and not useful characters from the device name.
This patch changes the name for the fec_mxc driver from
"FEC_MXC" to "FEC".
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This driver only provides initialization code; actual driving
is done by cmd_ide.c using the ATA compatibility mode of the
Marvell SATAHC controller.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Some commands (like 'mii') use this name to select devices, but they
break when those names contain spaces. So drop the space from
Ethernet driver names (cf. commit 1384f3bb).
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Ben Warren <biggerbadderben@gmail.com>
This patch add the basic infrastructure for the TWL6030 driver and enables
support in the two existing OMAP4 boards, Panda and OMAP4430 SDP
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch modifies the init routine to follow the TRM
recommendations. It also modifies the i2c_read_byte function
to reflect subtle differences between the i2c controller in
OMAP3 and OMAP4.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Nishanth Menon <menon.nishanth@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
While running from flash, i. e. before relocation, we have only a
limited C runtime environment without writable data segment. In this
phase, some configurations (for example with environment in EEPROM)
must not use the normal getenv(), but a special function. This
function had been called getenv_r(), with the idea that the "_r"
suffix would mean the same as in the _r_eentrant versions of some of
the C library functions (for example getdate vs. getdate_r, getgrent
vs. getgrent_r, etc.).
Unfortunately this was a misleading name, as in U-Boot the "_r"
generally means "running from RAM", i. e. _after_ relocation.
To avoid confusion, rename into getenv_f() [as "running from flash"]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
This patch adds support mmc driver for s5p SoC
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Lots of code use this construct:
cmd_usage(cmdtp);
return 1;
Change cmd_usage() let it return 1 - then we can replace all these
ocurrances by
return cmd_usage(cmdtp);
This fixes a few places with incorrect return code handling, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Since the vast majority of GPIO I2C implementations behave the same way,
support the common GPIO framework with default settings.
This adds two new defines CONFIG_SOFT_I2C_GPIO_{SCL,SDA} so that boards
which want GPIO I2C support need only define these.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p3041 to cpu_type_list and SVR list
* Added number of LAWs for p3041
* Set CONFIG_MAX_CPUS to 4 for p3041
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p5020 & p5010 to cpu_type_list and SVR list
* Added number of LAWs for p5020
* Set CONFIG_MAX_CPUS to 2 for p5020
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Previously we used an alias the pci node to determine which node to
fixup or delete. Now we use the new fdt_node_offset_by_compat_reg to
find the node to update.
Additionally, we replace the code in each board with a single macro call
that makes assumes uniform naming and reduces duplication in this area.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add printing of LAWBARH/LAWBARL for FSL_CORENET platforms.
Signed-off-by: Becky Bruce <Beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current code redefines functions based on FSL_CORENET_ vs not -
create macros/inlines instead that hide the differences.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently, 83xx, 86xx, and 85xx have a lot of duplicated code
dedicated to defining and manipulating the LBC registers. Merge
this into a single spot.
To do this, we have to decide on a common name for the data structure
that holds the lbc registers - it will now be known as fsl_lbc_t, and we
adopt a common name for the immap layouts that include the lbc - this was
previously known as either im_lbc or lbus; use the former.
In addition, create accessors for the BR/OR regs that use in/out_be32
and use those instead of the mismash of access methods currently in play.
I have done a successful ppc build all and tested a board or two from
each processor family.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some commands (like 'mii') use this name to select devices, but they break
when those names contain spaces. So drop the space from the Blackfin EMAC
driver.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than only support the pins dedicated as chip selects, utilize the
gpio framework to support any gpio pin.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than bang MMRs directly, use the new portmux framework to handle
the details.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Rather than bang MMRs directly, use the new portmux framework to handle
the details. While we're doing this, let boards declare the exact list
of pins they need in case there is one or two they don't actually have
hooked up.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Add definitions and initialization in orion5x for mvgbe.
Add orion5x in mvgbe SoC includes.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Rename all references to kirkwood in mvgbe symbols
throughout the whole codebase.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Rename kirkwood_egiga.* to mvgbe.* and adjust makefile
and #include accordingly.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This configuration option allows SoCs without random
generation capability to fill in local MACs with a fixed
rather than random value
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds the gpio usage request. The polarity is changed to
positive as suggested by Mike Frysinger.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
* the following problems are met :
config was set to use the new driver as a default but
- RMII was not enabled for the new driver
- the new driver didn't compile with RMII enabled
- the new driver initialize a PHY at address O when the PHY of
this board is at 1 thus we get "AT91 EMAC RMII: No PHY present"
* to fix these problems, this patch :
- enable RMII for the new driver
- fix the wrong define used in the at91_emac.c
- allow the config file to set a default phy address (and use
0 as a default as in the actual at91_emac.c driver)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The current dm9000x driver accesses its memory mapped registers directly
instead of using the standard I/O accessors. This can cause problems on
Blackfin systems as the accesses can get out of order. So convert the
direct volatile dereferences to use the normal in/out macros.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Hoan Hoang <hnhoan@i-syst.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The current OUTW function is always defined as a 16bit function, but this
doesn't work correctly when using the 32bit access mode. So define it as
a 32bit function when in 32bit mode so things work correctly on Blackfin
32bit LE systems.
Signed-off-by: Hoan Hoang <hnhoan@i-syst.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Some places in the current code equate the Marvell 88E1111 PHY as the family
when in reality it's a subpart of the Alaska family. So once we generalize
that, add support for the 88E1118 PHY.
Signed-off-by: Hoan Hoang <hnhoan@i-syst.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The Ethernet initialization functions are supposed to return the number of
devices initialized, so fix tsec_eth_init() so that they returns the number of
TSECs initialized, instead of just zero. This is safe because the return value
is currently ignored by all callers, but now they don't have to ignore it.
In general, if an function initializes only one device, then it should return
a negative number if there's an error. If it initializes more than one device,
then it should never return a negative number.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Device names should not contain non-printable characters like newlines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
No compiled code change here, just drop the local PHY defines in favor of
the common standard ones.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Rather than hardcode specific phy addresses, search the possible phy
address space to find the first available phy. Also respect the normal
CONFIG_PHY_ADDR option for board porters to pick a specific address.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
DRAM window mapping uses kirkwood-provided functions instead
of global gd as do other drivers--fix this.
Also, fix a typo in a comment
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Designware network driver support added.
This is a Synopsys ethernet controller
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Insert isb() sequence points to ensure DMA descriptors
are filled in and set up before actual DMA occurs.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
By defining CONFIG_M88E1111_DISABLE_FIBER boards can configure the
M88E1111 PYH to disable fiber. This is needed for an upcoming PPC460GT
based board, which has fiber/copper auto-selection enabled by default.
This doesn't seem to work. So we disable fiber in the PHY register.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The DM9000 in/out helper functions were casting the register address when
it was accessing things directly (pre commit a45dde2293). But
when it was changed to using the in/out helpers, those casts were dropped
because those functions don't take pointers. Even more recently, those
functions were then changed to use the read/write helpers, but the casts
were not re-added. This is necessary because the read/write helpers do
take pointers. Otherwise we get a lot of warnings like:
dm9000x.c: In function 'dm9000_inblk_8bit':
dm9000x.c:172: warning: passing argument 1 of 'readb'
makes pointer from integer without a cast
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
remove below warnings
serial_s5p.c: In function 'serial_getc_dev':
serial_s5p.c:136: warning: dereferencing type-punned pointer will break strict-aliasing rules
serial_s5p.c: In function 'serial_putc_dev':
serial_s5p.c:152: warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Make it easy to use GPIOs for the DEV_READY pin by using the common GPIO
framework. Also make the NAND_PLAT_INIT() define optional.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
The Toshiba TC58NVG0* parts are 128Mbytes x 8 bits 3.3V parts with the 0xD1
identifier. Add these to the list of known devices IDs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
When the NAND part is not supported, it is useful to show the manufacturer
and device ID to help debugging and reporting.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Two Indentation fixes.
Catch requests for full-duplex transfers when driver configured for
half-duplex operation only.
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
this eliminates compiler warnings when cmd_mmc.c is built with CONFIG_SYS_MMC_SET_DEV
the mmc_set_dev implementation in omap3_mmc.c is also tweaked to match
the new prototype in parameter naming and type
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch modifies the omap24xx driver so that it will also work with OMAP4.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The architecture independent header is moved to drivers/mmc, and the architecture
dependent headers reside in asm/arch-omap3 and asm/arch-omap4
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the second and third mmc channels on OMAP3
processors
Boards wishing to use this feature should define CONFIG_SYS_MMC_SET_DEV
in the board config
Tested on Overo
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Tested-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
At the moment, the default SPI flash subsystem is quite terse. Errors and
successes both result in a generic message. So move the useful errors and
useful successes to printf output by default.
While we're here, also convert the messages to use print_size().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some old STMicro parts do not support JEDEC ID (0x9f). This patch
uses RES (0xab) to get Electronic ID and translates it to JEDEC ID.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This avoids a build warning that you see if anyone in the
header chain has included io.h (which is coming shortly). The previous
code redefined readl/writel; this patch renames it to be specific to
ohci. The defines are also moved from ohci-hcd.c to ohci.h.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
MUSB PHY on OMAP3EVM Rev >= E uses external Vbus supply to support
500mA of power.We need to program MUSB PHY to use external Vbus
for this purpose.
Adding 'extvbus' member in musb_config structure which should be set
by all the boards where MUSB interface is using external Vbus supply.
Also added ULPI bus control register read/write abstraction for
Blackfin processor as it doesn't have ULPI registers.
CC: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Changed musb_config initialization for omap3.c, davinci.c
and da8xx.c using name of structure fields. This would cause
the uninitialized field to be null by default and thus would
help in avoiding to init some flags required to be set only
for a few selected platforms.
CC: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Add USB OHCI support for at91sam9g45ekes/at91sam9m10g45ek boards.
Note that according to errata from Atmel, OHCI is not operational
on the first revision of at91sam9g45 chip. So this patch enables
OHCI support for later revisions.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
ehci_submit_async() doesn't really zero out the QH transfer overlay (as the EHCI
specification suggests) which leads to the controller seeing the "token" field
as the previous call has left it, i.e.:
- if a timeout occured on the previous call (Active bit left as 1), controller
incorrectly tries to complete a previous transaction on a newly programmed
endpoint;
- if a halt occured on the previous call (Halted bit set to 1), controller just
ignores the newly programmed TD(s) and the function then keeps returning error
ad infinitum.
This turned out to be caused by the wrong orger of the arguments to the memset()
call in ehci_alloc(), so the allocated TDs weren't cleared either.
While at it, stop needlessly initializing the alternate next TD pointer in the
QH transfer overlay...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
On P2020RDB eTSEC2 is connected to Vitesse VSC8221 PHY via SGMII.
Current TBI PHY settings for SGMII mode cause link problems on
this platform, link never comes up.
Fix this by making TBI PHY settings configurable and add a working
configuration for P2020RDB.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Peter Tyser <ptyser@xes-inc.com>
The AmigaOneG3SE board has been orphaned or a very long time, and
broken for more than 12 releases resp. more than 3 years. As nobody
seems to be interested any more in this stuff we may as well ged rid
of it, especially as it clutters many areas of the code so it is a
continuous pain for all kinds of ongoing work.
Signed-off-by: Wolfgang Denk <wd@denx.de>
UBI: initialise update marker
The in kernel copy of a volume's update marker is not initialised from the
volume table. This means that volumes where an update was unfinnished will
not be treated as "forbidden to use". This is basically that the update
functionality was broken.
Signed-off-by: Peter Horton <zero@colonel-panic.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stefan Roese <sr@denx.de>
The following restructuring and optimisations increase the SPI
read performance from 1.3MiB/s (on da850) to 2.87MiB/s (on da830):
Remove continual revaluation of driver state from the core of the
copy loop. State can not change during the copy loop, so it is
possible to move these evaluations to before the copy loop.
Cost is more code space as loop variants are required for each set
of possible configurations. The loops are simpler however, so the
extra is only 128bytes on da830 with CONFIG_SPI_HALF_DUPLEX
defined.
Unrolling the first copy loop iteration allows the TX buffer to be
pre-loaded reducing SPI clock starvation.
Unrolling the last copy loop iteration removes testing for the
final loop iteration every time round the loop.
Using the RX buffer empty flag as a transfer throttle allows the
assumption that it is always safe to write to the TX buffer, so
polling of TX buffer full flag can be removed.
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
When set to PULL_NONE, gpio_set_pull function is returned without write the register.
This patch fixed it.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
For boards using sm501/sm502 on PCI bus some driver
functions normaly defined in the board code are not
needed and empty. Provide weak default functions for
them and do not enforce board code to define empty
functions.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Do not enforce drivers to provide empty video_set_lut()
if they do not implement indexed color (8 bpp) frame
buffer support. Add default function to the cfb_console
driver and remove empty video_set_lut() functions.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch enables PXAMCI support on PXA3xx CPUs. This patch only enables MMC1
though, MMC2 and PXA31x MMC3 will need further patch to be operational.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
In case the delays were set to 10000, the MMC card on PXA27X boards (and PXA3xx
boards) didn't initialize on first try. Increasing the delays and leaving just
those for PXA25x and 26x (that is 200000) fixes this problem.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
I have updated this patch based on the comments [1] by Wolfgang Denk and
removed unused variables.
[1][http://lists.denx.de/pipermail/u-boot/2010-May/071728.html]
Reduce the number of reads per byte transferred on the BUF register from 2 to 1 and
take advantage of the TX buffer in the SPI module. On LogicPD OMAP-L138 EVM,
SPI read throughput goes up from ~0.8Mbyte/s to ~1.3Mbyte/s. Tested with a 2Mbyte image file.
Remove unused variables in the spi_xfer() function.
Signed-off-by: Delio Brignoli <dbrignoli@audioscience.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds the driver of altera spi controller, which is
used as epcs/spi flash controller. It also works with mmc_spi
driver.
This driver support more than one spi bus, with base list declared
#define CONFIG_SYS_ALTERA_SPI_LIST { BASE_0,BASE_1,... }
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Tested-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
This patch adds a status led driver followed the GPIO access
conventions of Linux. The led mask is used to specify the gpio pin.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Tested-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
The current Blackfin nand write function fills up the write buffer but
returns before it has had a chance to drain. On faster systems, this
isn't a problem as the operation finishes before the ECC registers are
read, but on slower systems the ECC may be incomplete when the core tries
to read it.
So wait for the buffer to drain once we're done writing to it.
Signed-off-by: Andrew Caldwell <Andrew.Caldwell@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current U-Boot UBI implementation is copied from Linux. In this
porting the UBI background thread was not handled correctly. Upon write
operations ubi_wl_flush() makes sure, that all queued operations, like
page-erase, are completed. But this is missing for read operations.
This patch now makes sure that such operations (like scrubbing upon
bit-flip errors) are not queued, but executed directly.
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 77c1458d caused the following compiler warnings:
fsl_esdhc.c: In function 'esdhc_pio_read_write':
fsl_esdhc.c:142: warning: assignment discards qualifiers from pointer target type
fsl_esdhc.c: In function 'esdhc_setup_data':
fsl_esdhc.c:169: warning: unused variable 'wml_value'
fsl_esdhc.c: In function 'esdhc_pio_read_write':
fsl_esdhc.c:164: warning: control reaches end of non-void function
Fix these.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dipen Dudhat <dipen.dudhat@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
On the MPC85xx platform if we have SATA its connected on SERDES.
Determing if SATA is enabled via sata_initialize should not be board
specific and thus we move it out of the MPC8536DS board code.
Additionally, now that we have is_serdes_configured() we can determine
if the given SATA port is enabled and error out if its not in the
driver.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The x86 architecture exclusively uses Port-Mapped I/O (inb/outb) to access
the 16550 UARTs. This patch mimics how Linux selects between Memory-Mapped
and Port-Mapped I/O. This allows x86 boards to use CONFIG_SERIAL_MUTLI and
drop the custom serial port driver
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
In order to do this cleanly, the register accesses have to be converted to
a C struct (base pointer), so do that in the process.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The RTC is part of the Freescale's PMIC controller.
Use general function to access to PMIC internal registers.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
The patch add supports for the Freescale's Power
Management Controller (known as Atlas) used together with i.MX31/51
processors. It was tested with a MC13783 (MX31) and
MC13892 (MX51).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Added a new function kwgbe_write_hwaddr for programming egiga
controller's hardware address.
This function will be called for each egiga port being used
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This driver supports the Altera triple speeds 10/100/1000 ethernet
mac.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch ports the opencore 10/100 ethernet mac driver ethoc.c
from linux kernel to u-boot.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
SMSC911x chips have alignment function to allow frame payload data
(which comes after 14-bytes ethernet header) to be aligned at some
boundary when reading it from fifo (usually - 4 bytes boundary).
This is done by inserting fake zeros bytes BEFORE actual frame data when
reading from SMSC's fifo.
This function controlled by RX_CFG register. There are bits that
represents amount of fake bytes to be inserted.
Linux uses alignment of 4 bytes. Ethernet frame header is 14 bytes long,
so we need to add 2 fake bytes to get payload data aligned at 4-bytes
boundary.
Linux driver does this by adding IP_ALIGNMENT constant (defined at
skb.h) when calculating fifo data length. All network subsystem of Linux
uses this constant too when calculating different offsets.
But u-boot does not use any packet data alignment, so we don't need to
add anything when calculating fifo data length.
Moreover, driver zeros the RX_CFG register just one line up, so chip
does not insert any fake data at the beginig. So calculated data length
is always bigger by 1 word.
It seems that at almost every packet read we get an underflow condition
at fifo and possible corruption of data. Especially at continuous
transfers, such as tftp.
Just after removing this magic addition, I've got tftp transfer speed as
it aught to be at 100Mbps. It was really slow before.
It seems that fifo underflow occurs only when using byte packing on
32-bit blackfin bus (may be because of very small delay between reads).
Signed-off-by: Valentin Yakovenkov <yakovenkov@niistt.ru>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Cosmetic changes: Few comments updated
Functionality: Rx packet frame size is programming should
be done when port is in disabled state. this is corrected
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Vitaly Kuzmichev