Commit Graph

145 Commits

Author SHA1 Message Date
Vitaly Kuzmichev 58939fcc5c USB-CDC: Move MAC addresses setting into usb_eth_init
This allows to change device and host MAC addresses without performing
reset.

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2011-01-19 17:29:55 +01:00
Vitaly Kuzmichev 8f7aa831c3 USB-CDC: Do not rename netdev after its registration
Calling eth_bind at usb_eth_init time causes renaming of the network
device from 'usb_ether' to 'usb0'. Fixing this to keep the first name.

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2011-01-19 17:29:55 +01:00
Lei Wen 988ee3e3f0 usb_ether: register usb ethernet gadget at each eth init
Since the ether may not be the only one usb gadget would be used
in the uboot, it is neccessary to do the register each time the
eth begin to work to make usb gadget driver less confussed when
we want to use two different usb gadget at the same time.

Usb gadget driver could simple ignore the register operation, if
it find the driver has been registered already.

Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-01-19 17:29:55 +01:00
Stefan Roese a42a9d71b5 usb: Remove usb_dev_init() from ehci-ppc4xx.c
Calling usb_dev_init() from within the EHCI host driver is wrong.
The EHCI host driver should have no dependency/interconnection to the
USB device driver.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
2010-11-26 21:24:57 +01:00
Stefan Roese 273d72044c usb: Clear CMD_RUN while issuing CMD_RESET in ehci_reset()
This patch fixes a problem noticed on lwmon5 (PPC440EPx) using the
common EHCI driver, when "usb reset" is issued multiple times.
Upon the 2nd (and further) "usb reset" command, the command fails
with the following messages:

=> usb reset
(Re)start USB...
USB:   Register 1111 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 5 USB Device(s) found
       scanning bus for storage devices... 2 Storage Device(s) found
=> usb reset
(Re)start USB...
USB:   EHCI fail to reset
Error, couldn't init Lowlevel part

This patch fixes this problem. Now "usb reset" can be called multiple
times.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
2010-11-26 21:23:25 +01:00
Stefan Roese 67333f76b6 usb: Add WATCHDOG_RESET call to polling loop
This watchdog reset call is needed here, otherwise the lwmon5 board
(PPC440EPx based) will reset upon the "usb reset" command.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
2010-11-26 21:21:50 +01:00
Anatolij Gustschin 222d6dff27 usb: fix for USB_ST_STALLED status reporting in ehci_submit_async()
Checking the status field of the qTD token in the current code
do not take into acount cases where endpoint stall (halted) bit
is set together with XactErr status bit. As a result clearing
stall on an endpoint won't be done if this status bit was also
set. Check for halted bit and report USB_ST_STALLED status
if the host controller also indicates endpoit stall condition.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-11-26 21:21:16 +01:00
Sebastien Carlier 6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Wolfgang Denk 071bc92330 Coding Style cleanup
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-27 22:48:30 +02:00
Wolfgang Denk 09c83a45b7 ehci-hcd.c: fix hanging under higher load
This patch solves a problem with USB hanging under higher load on a
i.MX31 board.  It falls into class of typical USB problems and fixes:
if you don't understand the real cause, add a delay somewhere.

The problem appeared after introduction of ELF relocation, which
results in smaller code, which appears to run faster (probably because
it fits better in the cache); turning off the instruction cache,
adding debug printf()s and increasing the delay have all been found to
make the problem go away.

Moving the original "udelay(1)" up in the code to it's new place made
the problem appear much less frequently. Increasing the delay to 2
microseconds then made the code run reliably in all (hour-long) tests.
To be on the safe side, we set it to 5 microseconds here.

Signed-off-by: Heiko schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
2010-10-22 21:44:37 +02:00
Mike Frysinger 0228348e9c usb: musb: constify a bit
These ep and root hub structures need not be writable.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22 21:41:46 +02:00
Wolfgang Denk 8b675fe18e USB: fix Queue Element Transfer Descriptor changes
Commit 3ed1607 "USB: sync Queue Element Transfer Descriptor against
EHCI spec" added an "__attribute__ ((aligned (32)))" to the
declaration of struct qTD, as used for example in the Linux kernel as
well.

However, it turns out that this attribute causes errors in "usb start"
(like "ERROR: NOT USB_CONFIG_DESC 7b" and similar). Drop the attribute
again.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dan Lykowski <lykowdk@gmail.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
2010-10-22 21:41:45 +02:00
Florian Fainelli af68c06670 ehci-pci: print hccr, hcor and hc_lenght
It is useful to know the EHCI-PCI hccr, hcor and hc_lenght to make sure it was
successfully registered, and at the correct location.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2010-10-22 21:41:45 +02:00
Wolfgang Denk 3ed16071b0 USB: sync Queue Element Transfer Descriptor against EHCI spec
Appendix B "EHCI 64-Bit Data Structures" of the "Enhanced Host
Controller Interface Specification for Universal Serial Bus" (Rev.
1.0, March 12, 2002) defines additional fields which were missing in
U-Boot's struct qTD; as these are also present in recent versions of
struct ehci_qtd in the Linux kernel, we add them here, too.

This fixes some nasty memory corruption problems.

Reported-by: Dan Lykowski <lykowdk@gmail.com>
See http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/76942

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Dan Lykowski <lykowdk@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
2010-10-20 00:23:57 +02:00
Wolfgang Denk 083d506937 Merge branch 'master' of git://git.denx.de/u-boot-imx
Conflicts:
	board/logicpd/imx31_litekit/config.mk
	boards.cfg

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-19 20:58:16 +02:00
Damien Dusha 29c6fbe047 MPC5121: Add USB EHCI support
Signed-off-by: Francesco Rendine <francesco.rendine@valueteam.com>
Signed-off-by: Damien Dusha <d.dusha@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

Coding style cleanup; slight file restructuring.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Remy Bohmer <linux@bohmer.net>
2010-10-18 22:33:32 +02:00
Stefano Babic a2f9bff998 MX31: add delay between USB port setup and reset
Sometimes a usb tree is not popolated after a system reset.
It seems a delay is required after setting the USB ports
for the MX.31 before resetting the ehci controller.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-10-18 15:21:36 +02:00
Wolfgang Denk 6ca803750e Merge branch 'master' of git://git.denx.de/u-boot-imx 2010-10-17 19:57:38 +02:00
Stefano Babic 5b591502f9 MX31: Add support for MXC EHCI controller
The patch adds the EHCI controller for the i.MX31 Soc.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-10-13 18:11:44 +02:00
Bryan Wu 4ee691f6ac usb: musb: only write CLRDATATOG when appropriate
This is a change similar to what is already in the Linux driver.  We
should only program the CLRDATATOG bit when the current mode indicates
that it is needed.

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-13 12:08:43 +02:00
Vitaly Kuzmichev 98fae9707f USB-CDC: Prevent rx_req being enqueued twice
After gadget reinitializaton (after tftp has been done once)
packet_received may become equal to 1 due to nuking OUT_EP
while disabling it in eth_reset_config.

rx_submit called from usb_eth_init queues rx_req first time.
But the first call of usb_eth_recv from NetLoop queues rx_req
again due to packet_received = 1.

The following flow shows the path of functions calls when
this happens:

 net/net.c:NetLoop
 |
 +-net/eth.c:eth_init
 |   ether.c:usb_eth_init
 |   |
 |   +-udc_driver:usb_gadget_handle_interrupts
 |   |   udc_driver:...
 |   |     ether.c:eth_setup
 |   |       ether.c:eth_set_config
 |   |         ether.c:eth_reset_config
 |   |           udc_driver:usb_ep_disable
 |   |             udc_driver:nuke
 |   |               ether.c:rx_complete
 |   |                 ether.c: packet_received = 1;
 |   |
 |   +-ether.c:rx_submit
 |       udc_driver:usb_ep_queue --- The first time when rx_req is queued
 |
 +-net/eth.c:eth_rx
     ether.c:usb_eth_recv
     |
     +-udc_driver:usb_gadget_handle_interrupts
     |   udc_driver:... --- no interrupts, returning
     +-ether.c: if (packet_received) { ...
         ether.c:rx_submit
           udc_driver:usb_ep_queue --- The second time!

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-10-13 12:07:58 +02:00
Vitaly Kuzmichev ac5d32d15c USB-CDC: Fix tx/rx_req memory leaks
Remove and fix needless and destructive operations with tx/rx_req.

1) 'req' in rx_complete is always not NULL and always equals to rx_req
2) Free allocated tx_req if rx_req allocation has failed
3) Do not zero out tx/rx_req in usb_eth_init, leave this for
eth_reset_config which will be called at the next use of usb0
4) Additional check in usb_eth_recv is not required

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-10-13 12:07:58 +02:00
Marek Vasut f2443d10ff USB: Make non-bulk delay longer in OHCI
This fixes TIMEOUT with my Kingston 32GB USB3.0 flashdrive, which I experienced
on my PXA270 (USB 1.1) Vpac270 board.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-10-13 12:07:58 +02:00
Vitaly Kuzmichev 6142e0ae0f USB-CDC: Fix coding style issues
Fixes most of checkpatch warnings and errors in USB gadget stack.

The most frequently encountered problems are:
1) "(foo*)", "foo * bar", "foo* bar"
2) C99 // comments
3) No spaces before/after/around '?', ':', '=', '==', ',', '&', '('
4) Spaces before '['
5) Spaces between function names and '('
6) Block braces in wrong places
7) Spaces before tabs
8) Macros with complex values not enclosed in parenthesis
9) Multiline comments start just after /*

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-09-20 21:57:17 +02:00
Stefano Babic a170f2c797 USB-CDC: called handle_interrupts inside usb_eth_send
The patch removes an endless loop  in the usb_eth_send
if the tx_complete is not called before going
in the loop. The driver interrupt routine is called
allowing the driver to check if the TX is completed.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-20 21:57:17 +02:00
Stefano Babic 8046077219 USB-CDC: correct wrong alignment in ether.c
The buffer for the status request must be word aligned
because it is accessed with 32 bit pointer in the
eth_status_complete function.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-20 21:57:17 +02:00
Vitaly Kuzmichev c0ef513188 USB-CDC: change simple_strtol to simple_strtoul
The patch is based on commit bb9496c6f7e853e5d4edd5397c9d45f1968d623c
(done by Julia Lawall <julia@diku.dk>) from linux-2.6.git.

Since num is unsigned, it would seem better to use simple_strtoul that
simple_strtol.

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-09-20 21:57:17 +02:00
Vitaly Kuzmichev d5292c1647 USB-CDC: ethernet error path potential oops fix
Fix potential oops on rare error path.
The patch is based on commit e7b13ec9235b9fded90f826ceeb8c34548631351
(done by David Brownell <david-b@pacbell.net>) from linux-2.6.git.

Description of the issue taken from linux kernel bugzilla:
(https://bugzilla.kernel.org/show_bug.cgi?id=9594)

The potential error can be tracked down as follows:

(1) line 807: let the second conjunct on the "if" statment be false
    meaning "dev->status_ep" is null. This means the "if" evaluates
    to false.

follow thru the code until...

(2) line 808: usb_ep_disable(dev->status_ep) passes in a null argument,
    however "usb_ep_disable" cannot handle that:

(from include/linux/usb/gadget.h)
191 static inline int
192 usb_ep_disable (struct usb_ep *ep)
193 {
194         return ep->ops->disable (ep);
195 }

--

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-09-20 21:57:17 +02:00
Vitaly Kuzmichev df559c1d21 USB-CDC: Correct stat_req initialization
Fix possible oops on stat_req->buf initialization and fix ep0 and
status_ep confusion (last one is just intended for stat_req keeping).

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-20 21:57:17 +02:00
Vitaly Kuzmichev 2e12abe654 USB-CDC: Replace 'strcpy' by 'strlcpy'
Replace 'strcpy' by more safe 'strlcpy' that is implemented in ether.c

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-09-20 21:57:17 +02:00
Vitaly Kuzmichev 0129e327f4 USB-CDC: Correct freeing usb requests
Fix in_ep and out_ep confusion (rx_req was allocated from out_ep, not
from in_ep) and add lost dev->req freeing.

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-09-20 21:57:17 +02:00
Vitaly Kuzmichev 7de7318591 USB-CDC: Use native debug printout macros
Replace Linux-like debug printout macros by native ones.

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>

Applied after removing dead code like '#define DEBUG/#undef DEBUG'
2010-09-20 21:57:17 +02:00
Vitaly Kuzmichev 2721dbf1dd USB-CDC: Add lost 'qmult' definition
Add lost 'qmult' definition for High Speed devices and make it
configurable through CONFIG_USB_ETH_QMULT.

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-09-20 21:57:16 +02:00
Vitaly Kuzmichev 7b2f390611 USB-CDC: Restuct USB gadget Makefile
Prohibit simultaneous usage of both old and new gadget stacks and
allow UDC drivers to be dependent on CONFIG_USB_ETHER.

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-09-20 21:57:16 +02:00
Remy Bohmer 23cd138503 Integrate USB gadget layer and USB CDC driver layer
Derived from Linux kernel 2.6.27

Signed-off-by: Thomas Smits <ts.smits@gmail.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2010-09-20 21:57:16 +02:00
Mike Frysinger 70fccb3f24 usb: musb: stub out MUSB_TXCSR_MODE for Blackfin parts
The MUSB_TXCSR_MODE register setting isn't supported on Blackfin musb
parts, so stub it out to 0.  This matches Linux behavior.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-09-20 21:56:42 +02:00
Bryan Wu 93ceb4790d usb: musb: set target address for non-multipoint devices
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-09-11 09:49:22 +02:00
Bryan Wu 8dd7a23007 usb: musb: setup TXCOUNT for Blackfin musb
The Blackfin implementation of musb has a TXCOUNT register that needs to
be programmed when transmitting data.

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-09-11 09:49:21 +02:00
Ajay Kumar Gupta 5689f4b5b4 musb: am35x: Workaround for fifo read issue
AM35x supports only 32bit read operations so we need to have
workaround for 8bit and 16bit read operations.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
2010-08-12 16:40:00 +02:00
Ajay Kumar Gupta dbea324200 musb: MSC host support for AM35x
Tested MSC Host on AM3517EVM.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
2010-08-12 16:40:00 +02:00
Steve Sakoman 9b16757758 ARMV7: Restructure omap3 musb driver to allow code sharing between OMAP3 and OMAP4
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-08-05 10:11:34 -04:00
Ajay Kumar Gupta 900c0c6b0a musb: fix compilation warning
Fixes below compilation warning
omap3.c: In function 'musb_platform_init':
omap3.c:123: warning: implicit declaration of function
			'omap3_evm_need_extvbus'

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-15 16:11:01 -04:00
Becky Bruce a5496a180b drivers/usb/host/ohci-hcd: rename readl/writel to ohci_readl/ohci_writel
This avoids a build warning that you see if anyone in the
header chain has included io.h (which is coming shortly).  The previous
code redefined readl/writel; this patch renames it to be specific to
ohci.  The defines are also moved from ohci-hcd.c to ohci.h.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
2010-06-30 21:38:10 +02:00
Ajay Kumar Gupta 944a4894c0 musb: Program extvbus for OMAP3EVM Rev >= E
OMAP3EVM Rev >=E uses external Vbus supply so setting 'extvbus'
to '1' for OMAP3EVM Rev >=E runtime based on EVM revision.

CC: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
2010-06-30 21:37:37 +02:00
Ajay Kumar Gupta 9bb47abf0d musb: Add Phy programming for using external Vbus
MUSB PHY on OMAP3EVM Rev >= E uses external Vbus supply to support
500mA of power.We need to program MUSB PHY to use external Vbus
for this purpose.

Adding 'extvbus' member in musb_config structure which should be set
by all the boards where MUSB interface is using external Vbus supply.

Also added ULPI bus control register read/write abstraction for
Blackfin processor as it doesn't have ULPI registers.

CC: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2010-06-30 21:37:37 +02:00
Ajay Kumar Gupta bbf4c01efc musb: Use name based initialization for musb_config
Changed musb_config initialization for omap3.c, davinci.c
and da8xx.c using name of structure fields. This would cause
the uninitialized field to be null by default and thus would
help in avoiding to init some flags required to be set only
for a few selected platforms.

CC: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
2010-06-30 21:37:37 +02:00
Sergey Matyukevich 64203c7b0f USB OHCI support for at91sam9g45 SoC
Add USB OHCI support for at91sam9g45ekes/at91sam9m10g45ek boards.

Note that according to errata from Atmel, OHCI is not operational
on the first revision of at91sam9g45 chip. So this patch enables
OHCI support for later revisions.

Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
2010-06-30 21:37:36 +02:00
Sergei Shtylyov 9fb3b50857 EHCI: zero out QH transfer overlay in ehci_submit_async()
ehci_submit_async() doesn't really zero out the QH transfer overlay (as the EHCI
specification suggests) which leads to the controller seeing the "token" field
as the previous call has left it, i.e.:
- if a timeout occured on the previous call (Active bit left as 1), controller
  incorrectly tries to complete a previous transaction on a newly programmed
  endpoint;
- if a halt occured on the previous call (Halted bit set to 1), controller just
  ignores the newly programmed TD(s) and the function then keeps returning error
  ad infinitum.

This turned out to be caused by the wrong orger of the arguments to the memset()
call in ehci_alloc(), so the allocated TDs weren't cleared either.

While at it, stop needlessly initializing the alternate next TD pointer in the
QH transfer overlay...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
2010-06-29 23:03:40 +02:00
Ender.Dai 767fdc4af6 drivers/*/Makefile: fix conditional compile rule.
Fix conditional compile rule for twl4030.c and videomodes.c.

Signed-off-by: Ender.Dai <ender.dai@gmail.com>
2010-05-06 00:41:08 +02:00
Peter Tyser 1e3827d9cf mips: Move cpu/mips/* to arch/mips/cpu/*
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:25 +02:00