* Patch by Jon Loeliger, 2005-05-05

Implemented support for MPC8548CDS board.
  Added DDR II support based on SPD values for MPC85xx boards.
  This roll-up patch also includes bugfies for the previously
  published patches:
    DDRII CPO, pre eTSEC, 8548 LBIU, Andy's TSEC, eTSEC 3&4 I/O
This commit is contained in:
Jon Loeliger 2005-07-25 14:05:07 -05:00
parent 288693abe1
commit d9b94f28a4
36 changed files with 2612 additions and 392 deletions

View File

@ -1,6 +1,13 @@
======================================================================
Changes for U-Boot 1.1.3:
======================================================================
* Patch by Jon Loeliger, 2005-05-05
Implemented support for MPC8548CDS board.
Added DDR II support based on SPD values for MPC85xx boards.
This roll-up patch also includes bugfies for the previously
published patches:
DDRII CPO, pre eTSEC, 8548 LBIU, Andy's TSEC, eTSEC 3&4 I/O
* Patch by Jon Loeliger, 2005-Feb-10
Add config option CONFIG_HAS_FEC calling out 8540 FEC features.

View File

@ -111,9 +111,10 @@ LIST_8260=" \
#########################################################################
LIST_85xx=" \
MPC8540ADS MPC8541CDS MPC8555CDS MPC8560ADS \
PM854 sbc8540 sbc8560 stxgp3 \
TQM8540 \
MPC8540ADS MPC8541CDS MPC8548CDS MPC8555CDS \
MPC8560ADS PM854 sbc8540 sbc8560 \
stxgp3 TQM8540 \
"
#########################################################################

View File

@ -1193,6 +1193,9 @@ MPC8560ADS_config: unconfig
MPC8541CDS_config: unconfig
@./mkconfig $(@:_config=) ppc mpc85xx mpc8541cds cds
MPC8548CDS_config: unconfig
@./mkconfig $(@:_config=) ppc mpc85xx mpc8548cds cds
MPC8555CDS_config: unconfig
@./mkconfig $(@:_config=) ppc mpc85xx mpc8555cds cds

View File

@ -32,7 +32,7 @@
#include "../common/cadmus.h"
#include "../common/eeprom.h"
#if defined(CONFIG_DDR_ECC)
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif
@ -271,7 +271,7 @@ initdram(int board_type)
#endif
dram_size = spd_sdram();
#if defined(CONFIG_DDR_ECC)
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
/*
* Initialize and enable DDR ECC.
*/

View File

@ -0,0 +1,51 @@
#
# Copyright 2004 Freescale Semiconductor.
# (C) Copyright 2001
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#
include $(TOPDIR)/config.mk
LIB = lib$(BOARD).a
OBJS := $(BOARD).o \
../common/cadmus.o \
../common/eeprom.o
SOBJS := init.o
$(LIB): $(OBJS) $(SOBJS)
$(AR) crv $@ $(OBJS)
clean:
rm -f $(OBJS) $(SOBJS)
distclean: clean
rm -f $(LIB) core *.bak .depend
#########################################################################
.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
-include .depend
#########################################################################

View File

@ -0,0 +1,30 @@
#
# Copyright 2004 Freescale Semiconductor.
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#
#
# mpc8548cds board
#
TEXT_BASE = 0xfff80000
PLATFORM_CPPFLAGS += -DCONFIG_E500=1
PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
PLATFORM_CPPFLAGS += -DCONFIG_MPC8548=1

255
board/cds/mpc8548cds/init.S Normal file
View File

@ -0,0 +1,255 @@
/*
* Copyright 2004 Freescale Semiconductor.
* Copyright 2002,2003, Motorola Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <ppc_asm.tmpl>
#include <ppc_defs.h>
#include <asm/cache.h>
#include <asm/mmu.h>
#include <config.h>
#include <mpc85xx.h>
/*
* TLB0 and TLB1 Entries
*
* Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR.
* However, CCSRBAR is then relocated to CFG_CCSRBAR right after
* these TLB entries are established.
*
* The TLB entries for DDR are dynamically setup in spd_sdram()
* and use TLB1 Entries 8 through 15 as needed according to the
* size of DDR memory.
*
* MAS0: tlbsel, esel, nv
* MAS1: valid, iprot, tid, ts, tsize
* MAS2: epn, sharen, x0, x1, w, i, m, g, e
* MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr
*/
#define entry_start \
mflr r1 ; \
bl 0f ;
#define entry_end \
0: mflr r0 ; \
mtlr r1 ; \
blr ;
.section .bootpg, "ax"
.globl tlb1_entry
tlb1_entry:
entry_start
/*
* Number of TLB0 and TLB1 entries in the following table
*/
.long 13
#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
/*
* TLB0 4K Non-cacheable, guarded
* 0xff700000 4K Initial CCSRBAR mapping
*
* This ends up at a TLB0 Index==0 entry, and must not collide
* with other TLB0 Entries.
*/
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1)
#else
#error("Update the number of table entries in tlb1_entry")
#endif
/*
* TLB0 16K Cacheable, non-guarded
* 0xd001_0000 16K Temporary Global data for initialization
*
* Use four 4K TLB0 entries. These entries must be cacheable
* as they provide the bootstrap memory before the memory
* controler and real memory have been configured.
*
* These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
* and must not collide with other TLB0 entries.
*/
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR),
0,0,0,0,0,0,0,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR),
0,0,0,0,0,1,0,1,0,1)
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024),
0,0,0,0,0,0,0,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024),
0,0,0,0,0,1,0,1,0,1)
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),
0,0,0,0,0,0,0,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024),
0,0,0,0,0,1,0,1,0,1)
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024),
0,0,0,0,0,0,0,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024),
0,0,0,0,0,1,0,1,0,1)
/*
* TLB 0: 16M Non-cacheable, guarded
* 0xff000000 16M FLASH
* Out of reset this entry is only 4K.
*/
.long TLB1_MAS0(1, 0, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1)
/*
* TLB 1: 256M Non-cacheable, guarded
* 0x80000000 256M PCI1 MEM First half
*/
.long TLB1_MAS0(1, 1, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
/*
* TLB 2: 256M Non-cacheable, guarded
* 0x90000000 256M PCI1 MEM Second half
*/
.long TLB1_MAS0(1, 2, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000),
0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000),
0,0,0,0,0,1,0,1,0,1)
/*
* TLB 3: 256M Non-cacheable, guarded
* 0xa0000000 256M PCI2 MEM First half
*/
.long TLB1_MAS0(1, 3, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
/*
* TLB 4: 256M Non-cacheable, guarded
* 0xb0000000 256M PCI2 MEM Second half
*/
.long TLB1_MAS0(1, 4, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE + 0x10000000),
0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE + 0x10000000),
0,0,0,0,0,1,0,1,0,1)
/*
* TLB 5: 64M Non-cacheable, guarded
* 0xe000_0000 1M CCSRBAR
* 0xe200_0000 16M PCI1 IO
* 0xe300_0000 16M PCI2 IO
*/
.long TLB1_MAS0(1, 5, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
/*
* TLB 6: 64M Cacheable, non-guarded
* 0xf000_0000 64M LBC SDRAM
*/
.long TLB1_MAS0(1, 6, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1)
/*
* TLB 7: 1M Non-cacheable, guarded
* 0xf8000000 1M CADMUS registers
*/
.long TLB1_MAS0(1, 7, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M)
.long TLB1_MAS2(E500_TLB_EPN(CADMUS_BASE_ADDR), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CADMUS_BASE_ADDR), 0,0,0,0,0,1,0,1,0,1)
entry_end
/*
* LAW(Local Access Window) configuration:
*
* 0x0000_0000 0x7fff_ffff DDR 2G
* 0x8000_0000 0x9fff_ffff PCI1 MEM 512M
* 0xa000_0000 0xbfff_ffff PCI2 MEM 512M
* 0xe000_0000 0xe000_ffff CCSR 1M
* 0xe200_0000 0xe2ff_ffff PCI1 IO 16M
* 0xe300_0000 0xe3ff_ffff PCI2 IO 16M
* 0xf000_0000 0xf7ff_ffff SDRAM 128M
* 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M
* 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M
* 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M
*
* Notes:
* CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
* If flash is 8M at default position (last 8M), no LAW needed.
*
* The defines below are 1-off of the actual LAWAR0 usage.
* So LAWAR3 define uses the LAWAR4 register in the ECM.
*/
#define LAWBAR0 0
#define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M))
#define LAWBAR2 ((CFG_PCI2_MEM_BASE>>12) & 0xfffff)
#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M))
#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M))
#define LAWBAR4 ((CFG_PCI2_IO_BASE>>12) & 0xfffff)
#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_16M))
/* LBC window - maps 256M 0xf0000000 -> 0xffffffff */
#define LAWBAR5 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
#define LAWAR5 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
.section .bootpg, "ax"
.globl law_entry
law_entry:
entry_start
.long 6
.long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3
.long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5
entry_end

View File

@ -0,0 +1,329 @@
/*
* Copyright 2004 Freescale Semiconductor.
*
* (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <pci.h>
#include <asm/processor.h>
#include <asm/immap_85xx.h>
#include <spd.h>
#include "../common/cadmus.h"
#include "../common/eeprom.h"
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif
extern long int spd_sdram(void);
void local_bus_init(void);
void sdram_init(void);
int board_early_init_f (void)
{
return 0;
}
int checkboard (void)
{
volatile immap_t *immap = (immap_t *) CFG_CCSRBAR;
volatile ccsr_gur_t *gur = &immap->im_gur;
/* PCI slot in USER bits CSR[6:7] by convention. */
uint pci_slot = get_pci_slot ();
uint pci_dual = get_pci_dual (); /* PCI DUAL in CM_PCI[3] */
uint pci1_32 = gur->pordevsr & 0x10000; /* PORDEVSR[15] */
uint pci1_clk_sel = gur->porpllsr & 0x8000; /* PORPLLSR[16] */
uint pci2_clk_sel = gur->porpllsr & 0x4000; /* PORPLLSR[17] */
uint pci1_speed = get_clock_freq (); /* PCI PSPEED in [4:5] */
uint cpu_board_rev = get_cpu_board_revision ();
printf ("Board: CDS Version 0x%02x, PCI Slot %d\n",
get_board_version (), pci_slot);
printf ("CPU Board Revision %d.%d (0x%04x)\n",
MPC85XX_CPU_BOARD_MAJOR (cpu_board_rev),
MPC85XX_CPU_BOARD_MINOR (cpu_board_rev), cpu_board_rev);
printf (" PCI1: %d bit, %s MHz, %s\n",
(pci1_32) ? 32 : 64,
(pci1_speed == 33000000) ? "33" :
(pci1_speed == 66000000) ? "66" : "unknown",
pci1_clk_sel ? "sync" : "async");
if (pci_dual) {
printf (" PCI2: 32 bit, 66 MHz, %s\n",
pci2_clk_sel ? "sync" : "async");
} else {
printf (" PCI2: disabled\n");
}
/*
* Initialize local bus.
*/
local_bus_init ();
/*
* Hack TSEC 3 and 4 IO voltages.
*/
gur->tsec34ioovcr = 0xe7e0; /* 1110 0111 1110 0xxx */
return 0;
}
long int
initdram(int board_type)
{
long dram_size = 0;
volatile immap_t *immap = (immap_t *)CFG_IMMR;
puts("Initializing\n");
#if defined(CONFIG_DDR_DLL)
{
/*
* Work around to stabilize DDR DLL MSYNC_IN.
* Errata DDR9 seems to have been fixed.
* This is now the workaround for Errata DDR11:
* Override DLL = 1, Course Adj = 1, Tap Select = 0
*/
volatile ccsr_gur_t *gur= &immap->im_gur;
gur->ddrdllcr = 0x81000000;
asm("sync;isync;msync");
udelay(200);
}
#endif
dram_size = spd_sdram();
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
/*
* Initialize and enable DDR ECC.
*/
ddr_enable_ecc(dram_size);
#endif
/*
* SDRAM Initialization
*/
sdram_init();
puts(" DDR: ");
return dram_size;
}
/*
* Initialize Local Bus
*/
void
local_bus_init(void)
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile ccsr_gur_t *gur = &immap->im_gur;
volatile ccsr_lbc_t *lbc = &immap->im_lbc;
uint clkdiv;
uint lbc_hz;
sys_info_t sysinfo;
get_sys_info(&sysinfo);
clkdiv = (lbc->lcrr & 0x0f) * 2;
lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
gur->lbiuiplldcr1 = 0x00078080;
if (clkdiv == 16) {
gur->lbiuiplldcr0 = 0x7c0f1bf0;
} else if (clkdiv == 8) {
gur->lbiuiplldcr0 = 0x6c0f1bf0;
} else if (clkdiv == 4) {
gur->lbiuiplldcr0 = 0x5c0f1bf0;
}
lbc->lcrr |= 0x00030000;
asm("sync;isync;msync");
}
/*
* Initialize SDRAM memory on the Local Bus.
*/
void
sdram_init(void)
{
#if defined(CFG_OR2_PRELIM) && defined(CFG_BR2_PRELIM)
uint idx;
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile ccsr_lbc_t *lbc = &immap->im_lbc;
uint *sdram_addr = (uint *)CFG_LBC_SDRAM_BASE;
uint cpu_board_rev;
uint lsdmr_common;
puts(" SDRAM: ");
print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
/*
* Setup SDRAM Base and Option Registers
*/
lbc->or2 = CFG_OR2_PRELIM;
asm("msync");
lbc->br2 = CFG_BR2_PRELIM;
asm("msync");
lbc->lbcr = CFG_LBC_LBCR;
asm("msync");
lbc->lsrt = CFG_LBC_LSRT;
lbc->mrtpr = CFG_LBC_MRTPR;
asm("msync");
/*
* MPC8548 uses "new" 15-16 style addressing.
*/
cpu_board_rev = get_cpu_board_revision();
lsdmr_common = CFG_LBC_LSDMR_COMMON;
lsdmr_common |= CFG_LBC_LSDMR_BSMA1516;
/*
* Issue PRECHARGE ALL command.
*/
lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_PCHALL;
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
udelay(100);
/*
* Issue 8 AUTO REFRESH commands.
*/
for (idx = 0; idx < 8; idx++) {
lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_ARFRSH;
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
udelay(100);
}
/*
* Issue 8 MODE-set command.
*/
lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_MRW;
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
udelay(100);
/*
* Issue NORMAL OP command.
*/
lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_NORMAL;
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
udelay(200); /* Overkill. Must wait > 200 bus cycles */
#endif /* enable SDRAM init */
}
#if defined(CFG_DRAM_TEST)
int
testdram(void)
{
uint *pstart = (uint *) CFG_MEMTEST_START;
uint *pend = (uint *) CFG_MEMTEST_END;
uint *p;
printf("Testing DRAM from 0x%08x to 0x%08x\n",
CFG_MEMTEST_START,
CFG_MEMTEST_END);
printf("DRAM test phase 1:\n");
for (p = pstart; p < pend; p++)
*p = 0xaaaaaaaa;
for (p = pstart; p < pend; p++) {
if (*p != 0xaaaaaaaa) {
printf ("DRAM test fails at: %08x\n", (uint) p);
return 1;
}
}
printf("DRAM test phase 2:\n");
for (p = pstart; p < pend; p++)
*p = 0x55555555;
for (p = pstart; p < pend; p++) {
if (*p != 0x55555555) {
printf ("DRAM test fails at: %08x\n", (uint) p);
return 1;
}
}
printf("DRAM test passed.\n");
return 0;
}
#endif
#if defined(CONFIG_PCI)
/*
* Initialize PCI Devices, report devices found.
*/
#ifndef CONFIG_PCI_PNP
static struct pci_config_table pci_mpc85xxcds_config_table[] = {
{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
PCI_IDSEL_NUMBER, PCI_ANY_ID,
pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
PCI_ENET0_MEMADDR,
PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER
} },
{ }
};
#endif
static struct pci_controller hose = {
#ifndef CONFIG_PCI_PNP
config_table: pci_mpc85xxcds_config_table,
#endif
};
#endif /* CONFIG_PCI */
void
pci_init_board(void)
{
#ifdef CONFIG_PCI
extern void pci_mpc85xx_init(struct pci_controller *hose);
pci_mpc85xx_init(&hose);
#endif
}

View File

@ -0,0 +1,147 @@
/*
* Copyright 2004 Freescale Semiconductor.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
OUTPUT_ARCH(powerpc)
SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
/* Do we need any of these for elf?
__DYNAMIC = 0; */
SECTIONS
{
.resetvec 0xFFFFFFFC :
{
*(.resetvec)
} = 0xffff
.bootpg 0xFFFFF000 :
{
cpu/mpc85xx/start.o (.bootpg)
board/cds/mpc8548cds/init.o (.bootpg)
} = 0xffff
/* Read-only sections, merged into text segment: */
. = + SIZEOF_HEADERS;
.interp : { *(.interp) }
.hash : { *(.hash) }
.dynsym : { *(.dynsym) }
.dynstr : { *(.dynstr) }
.rel.text : { *(.rel.text) }
.rela.text : { *(.rela.text) }
.rel.data : { *(.rel.data) }
.rela.data : { *(.rela.data) }
.rel.rodata : { *(.rel.rodata) }
.rela.rodata : { *(.rela.rodata) }
.rel.got : { *(.rel.got) }
.rela.got : { *(.rela.got) }
.rel.ctors : { *(.rel.ctors) }
.rela.ctors : { *(.rela.ctors) }
.rel.dtors : { *(.rel.dtors) }
.rela.dtors : { *(.rela.dtors) }
.rel.bss : { *(.rel.bss) }
.rela.bss : { *(.rela.bss) }
.rel.plt : { *(.rel.plt) }
.rela.plt : { *(.rela.plt) }
.init : { *(.init) }
.plt : { *(.plt) }
.text :
{
cpu/mpc85xx/start.o (.text)
board/cds/mpc8548cds/init.o (.text)
cpu/mpc85xx/traps.o (.text)
cpu/mpc85xx/interrupts.o (.text)
cpu/mpc85xx/cpu_init.o (.text)
cpu/mpc85xx/cpu.o (.text)
cpu/mpc85xx/tsec.o (.text)
cpu/mpc85xx/speed.o (.text)
cpu/mpc85xx/pci.o (.text)
common/dlmalloc.o (.text)
lib_generic/crc32.o (.text)
lib_ppc/extable.o (.text)
lib_generic/zlib.o (.text)
*(.text)
*(.fixup)
*(.got1)
}
_etext = .;
PROVIDE (etext = .);
.rodata :
{
*(.rodata)
*(.rodata1)
*(.rodata.str1.4)
}
.fini : { *(.fini) } =0
.ctors : { *(.ctors) }
.dtors : { *(.dtors) }
/* Read-write section, merged into data segment: */
. = (. + 0x00FF) & 0xFFFFFF00;
_erotext = .;
PROVIDE (erotext = .);
.reloc :
{
*(.got)
_GOT2_TABLE_ = .;
*(.got2)
_FIXUP_TABLE_ = .;
*(.fixup)
}
__got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
__fixup_entries = (. - _FIXUP_TABLE_) >> 2;
.data :
{
*(.data)
*(.data1)
*(.sdata)
*(.sdata2)
*(.dynamic)
CONSTRUCTORS
}
_edata = .;
PROVIDE (edata = .);
__u_boot_cmd_start = .;
.u_boot_cmd : { *(.u_boot_cmd) }
__u_boot_cmd_end = .;
__start___ex_table = .;
__ex_table : { *(__ex_table) }
__stop___ex_table = .;
. = ALIGN(256);
__init_begin = .;
.text.init : { *(.text.init) }
.data.init : { *(.data.init) }
. = ALIGN(256);
__init_end = .;
__bss_start = .;
.bss :
{
*(.sbss) *(.scommon)
*(.dynbss)
*(.bss)
*(COMMON)
}
_end = . ;
PROVIDE (end = .);
}

View File

@ -30,7 +30,7 @@
#include "../common/cadmus.h"
#include "../common/eeprom.h"
#if defined(CONFIG_DDR_ECC)
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif
@ -269,7 +269,7 @@ initdram(int board_type)
#endif
dram_size = spd_sdram();
#if defined(CONFIG_DDR_ECC)
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
/*
* Initialize and enable DDR ECC.
*/

View File

@ -31,7 +31,7 @@
#include <asm/immap_85xx.h>
#include <spd.h>
#if defined(CONFIG_DDR_ECC)
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif
@ -96,7 +96,7 @@ initdram(int board_type)
dram_size = fixed_sdram ();
#endif
#if defined(CONFIG_DDR_ECC)
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
/*
* Initialize and enable DDR ECC.
*/

View File

@ -33,7 +33,7 @@
#include <spd.h>
#include <miiphy.h>
#if defined(CONFIG_DDR_ECC)
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif
@ -293,7 +293,7 @@ initdram(int board_type)
dram_size = fixed_sdram ();
#endif
#if defined(CONFIG_DDR_ECC)
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
/*
* Initialize and enable DDR ECC.
*/

View File

@ -38,6 +38,7 @@ int checkcpu (void)
uint lcrr; /* local bus clock ratio register */
uint clkdiv; /* clock divider portion of lcrr */
uint pvr, svr;
uint fam;
uint ver;
uint major, minor;
@ -60,6 +61,12 @@ int checkcpu (void)
case SVR_8560:
puts("8560");
break;
case SVR_8548:
puts("8548");
break;
case SVR_8548_E:
puts("8548_E");
break;
default:
puts("Unknown");
break;
@ -67,13 +74,14 @@ int checkcpu (void)
printf(", Version: %d.%d, (0x%08x)\n", major, minor, svr);
pvr = get_pvr();
fam = PVR_FAM(pvr);
ver = PVR_VER(pvr);
major = PVR_MAJ(pvr);
minor = PVR_MIN(pvr);
printf("Core: ");
switch (ver) {
case PVR_VER(PVR_85xx):
switch (fam) {
case PVR_FAM(PVR_85xx):
puts("E500");
break;
default:
@ -84,7 +92,7 @@ int checkcpu (void)
get_sys_info(&sysinfo);
puts("Clocks Configuration:\n");
puts("Clock Configuration:\n");
printf(" CPU:%4lu MHz, ", sysinfo.freqProcessor / 1000000);
printf("CCB:%4lu MHz,\n", sysinfo.freqSystemBus / 1000000);
printf(" DDR:%4lu MHz, ", sysinfo.freqSystemBus / 2000000);
@ -101,6 +109,13 @@ int checkcpu (void)
#endif
clkdiv = lcrr & 0x0f;
if (clkdiv == 2 || clkdiv == 4 || clkdiv == 8) {
#ifdef CONFIG_MPC8548
/*
* Yes, the entire PQ38 family use the same
* bit-representation for twice the clock divider values.
*/
clkdiv *= 2;
#endif
printf("LBC:%4lu MHz\n",
sysinfo.freqSystemBus / 1000000 / clkdiv);
} else {

View File

@ -178,42 +178,58 @@ void cpu_init_f (void)
#endif
}
/*
* We initialize L2 as cache here.
* Initialize L2 as cache.
*
* The newer 8548, etc, parts have twice as much cache, but
* use the same bit-encoding as the older 8555, etc, parts.
*
* FIXME: Use PVR_VER(pvr) == 1 test here instead of SVR_VER()?
*/
int cpu_init_r (void)
int cpu_init_r(void)
{
#if defined(CONFIG_L2_CACHE)
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile ccsr_l2cache_t *l2cache = &immap->im_l2cache;
volatile uint temp;
volatile uint cache_ctl;
uint svr, ver;
svr = get_svr();
ver = SVR_VER(svr);
asm("msync;isync");
temp = l2cache->l2ctl;
temp &= 0x30000000;
switch ( temp ) {
cache_ctl = l2cache->l2ctl;
switch (cache_ctl & 0x30000000) {
case 0x20000000:
printf ("L2 cache 256KB:");
if (ver == SVR_8548 || ver == SVR_8548_E) {
printf ("L2 cache 512KB:");
} else {
printf ("L2 cache 256KB:");
}
break;
case 0x00000000:
case 0x10000000:
case 0x30000000:
default:
printf ("L2 cache unknown size. Check the silicon!\n");
printf ("L2 cache unknown size (0x%08x)\n", cache_ctl);
return -1;
}
asm("msync;isync");
l2cache->l2ctl = 0x68000000; /* invalidate */
temp = l2cache->l2ctl;
asm("msync;isync");
l2cache->l2ctl = 0xa8000000; /* enable 256KB L2 cache */
temp = l2cache->l2ctl;
cache_ctl = l2cache->l2ctl;
asm("msync;isync");
printf("enabled\n");
l2cache->l2ctl = 0xa8000000; /* enable 256KB L2 cache */
cache_ctl = l2cache->l2ctl;
asm("msync;isync");
printf(" enabled\n");
#else
printf("L2: disabled.\n");
printf("L2 cache: disabled\n");
#endif
return 0;

File diff suppressed because it is too large Load Diff

View File

@ -174,6 +174,9 @@ _start_e500:
mtspr BUCSR,r0 /* disable branch prediction */
mtspr MAS4,r0
mtspr MAS6,r0
#if defined(CONFIG_ENABLE_36BIT_PHYS)
mtspr MAS7,r0
#endif
isync
/* Setup interrupt vectors */
@ -358,6 +361,9 @@ _start:
/* Enable Time Base and Select Time Base Clock */
lis r0,HID0_EMCP@h /* Enable machine check */
ori r0,r0,0x4000 /* time base is processor clock */
#if defined(CONFIG_ENABLE_36BIT_PHYS)
ori r0,r0,0x0080 /* enable MAS7 updates */
#endif
mtspr HID0,r0
#if defined(CONFIG_ADDR_STREAMING)

View File

@ -35,7 +35,7 @@ typedef volatile struct rtxbd {
struct tsec_info_struct {
unsigned int phyaddr;
unsigned int gigabit;
u32 flags;
unsigned int phyregidx;
};
@ -48,8 +48,9 @@ struct tsec_info_struct {
* phyaddr - The address of the PHY which is attached to
* the given device.
*
* gigabit - This variable indicates whether the device
* supports gigabit speed ethernet
* flags - This variable indicates whether the device
* supports gigabit speed ethernet, and whether it should be
* in reduced mode.
*
* phyregidx - This variable specifies which ethernet device
* controls the MII Management registers which are connected
@ -70,23 +71,32 @@ struct tsec_info_struct {
*/
static struct tsec_info_struct tsec_info[] = {
#ifdef CONFIG_MPC85XX_TSEC1
{TSEC1_PHY_ADDR, 1, TSEC1_PHYIDX},
{TSEC1_PHY_ADDR, TSEC_GIGABIT, TSEC1_PHYIDX},
#else
{ 0, 0, 0},
#endif
#ifdef CONFIG_MPC85XX_TSEC2
{TSEC2_PHY_ADDR, 1, TSEC2_PHYIDX},
{TSEC2_PHY_ADDR, TSEC_GIGABIT, TSEC2_PHYIDX},
#else
{ 0, 0, 0},
#endif
#ifdef CONFIG_MPC85XX_FEC
{FEC_PHY_ADDR, 0, FEC_PHYIDX},
#else
# ifdef CONFIG_MPC85XX_TSEC3
{TSEC3_PHY_ADDR, TSEC_GIGABIT | TSEC_REDUCED, TSEC3_PHYIDX},
# else
{ 0, 0, 0},
# endif
# ifdef CONFIG_MPC85XX_TSEC4
{TSEC4_PHY_ADDR, TSEC_REDUCED, TSEC4_PHYIDX},
# else
{ 0, 0, 0},
# endif
#endif
};
#define MAXCONTROLLERS 3
#define MAXCONTROLLERS (4)
static int relocated = 0;
@ -115,7 +125,7 @@ static void relocate_cmds(void);
/* Initialize device structure. Returns success if PHY
* initialization succeeded (i.e. if it recognizes the PHY)
*/
int tsec_initialize(bd_t *bis, int index)
int tsec_initialize(bd_t *bis, int index, char *devname)
{
struct eth_device* dev;
int i;
@ -139,9 +149,9 @@ int tsec_initialize(bd_t *bis, int index)
tsec_info[index].phyregidx*TSEC_SIZE);
priv->phyaddr = tsec_info[index].phyaddr;
priv->gigabit = tsec_info[index].gigabit;
priv->flags = tsec_info[index].flags;
sprintf(dev->name, "ENET%d", index);
sprintf(dev->name, devname);
dev->iobase = 0;
dev->priv = priv;
dev->init = tsec_init;
@ -318,7 +328,7 @@ static int init_phy(struct eth_device *dev)
/* For 10/100, the value is slightly different */
uint mii_cr_init(uint mii_reg, struct tsec_private *priv)
{
if(priv->gigabit)
if(priv->flags & TSEC_GIGABIT)
return MIIM_CONTROL_INIT;
else
return MIIM_CR_INIT;
@ -438,6 +448,13 @@ uint mii_cis8204_fixled(uint mii_reg, struct tsec_private *priv)
return MIIM_CIS8204_SLEDCON_INIT;
}
uint mii_cis8204_setmode(uint mii_reg, struct tsec_private *priv)
{
if (priv->flags & TSEC_REDUCED)
return MIIM_CIS8204_EPHYCON_INIT | MIIM_CIS8204_EPHYCON_RGMII;
else
return MIIM_CIS8204_EPHYCON_INIT;
}
/* Initialized required registers to appropriate values, zeroing
* those we don't care about (unless zero is bad, in which case,
@ -507,6 +524,15 @@ static void adjust_link(struct eth_device *dev)
case 10:
regs->maccfg2 = ((regs->maccfg2&~(MACCFG2_IF))
| MACCFG2_MII);
/* If We're in reduced mode, we
* need to say whether we're 10
* or 100 MB. */
if ((priv->speed == 100)
&& (priv->flags & TSEC_REDUCED))
regs->ecntrl |= ECNTRL_R100;
else
regs->ecntrl &= ~(ECNTRL_R100);
break;
default:
printf("%s: Speed was bad\n", dev->name);
@ -731,7 +757,7 @@ struct phy_info phy_info_cis8204 = {
/* Configure some basic stuff */
{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
{MIIM_CIS8204_SLED_CON, MIIM_CIS8204_SLEDCON_INIT, &mii_cis8204_fixled},
{MIIM_CIS8204_EPHY_CON, MIIM_CIS8204_EPHYCON_INIT, NULL},
{MIIM_CIS8204_EPHY_CON, MIIM_CIS8204_EPHYCON_INIT, &mii_cis8204_setmode},
{miim_end,}
},
(struct phy_cmd[]) { /* startup */

View File

@ -51,6 +51,7 @@
#define ECNTRL_INIT_SETTINGS 0x00001000
#define ECNTRL_TBI_MODE 0x00000020
#define ECNTRL_R100 0x00000008
#define miim_end -2
#define miim_read -1
@ -107,6 +108,7 @@
/* Cicada 8204 Extended PHY Control Register 1 */
#define MIIM_CIS8204_EPHY_CON 0x17
#define MIIM_CIS8204_EPHYCON_INIT 0x0006
#define MIIM_CIS8204_EPHYCON_RGMII 0x1000
/* Cicada 8204 Serial LED Control Register */
#define MIIM_CIS8204_SLED_CON 0x1b
@ -424,12 +426,18 @@ typedef struct tsec
uint resc00[256];
} tsec_t;
#define TSEC_GIGABIT (1)
/* This flag currently only has
* meaning if we're using the eTSEC */
#define TSEC_REDUCED (1 << 1)
struct tsec_private {
volatile tsec_t *regs;
volatile tsec_t *phyregs;
struct phy_info *phyinfo;
uint phyaddr;
uint gigabit;
u32 flags;
uint link;
uint duplexity;
uint speed;

View File

@ -143,6 +143,7 @@ Updated 13-July-2004 Jon Loeliger
CONFIG_DDR_ECC only for ECC DDR module
CONFIG_DDR_DLL DLL fix on some ADS boards needed for more
stability.
CONFIG_HAS_FEC If an FEC is on chip, set to 1, else 0.
Other than the above definitions, the rest in the config files are
straightforward.
@ -190,10 +191,10 @@ straightforward.
4.4 Reflash U-boot Image using U-boot
=> tftp 10000 u-boot.bin
=> protect off fff80000 ffffffff
=> erase fff80000 ffffffff
=> cp.b 10000 fff80000 80000
tftp 10000 u-boot.bin
protect off fff80000 ffffffff
erase fff80000 ffffffff
cp.b 10000 fff80000 80000
4.5 Reflash U-Boot with a BDI-2000

View File

@ -135,8 +135,8 @@ The default setting of all switches on the carrier board is:
SW4=10001000
CPU Card Switches
-----------------
8555/41 CPU Card Switches
-------------------------
Most switches on the CPU Card should not be changed. However, the
frequency can be changed by setting SW3:
@ -160,6 +160,45 @@ A safe default setting for all switches on the CPU board is:
SW4=11111110
8548 CPU Card Switches
----------------------
And, just to be confusing, in this set of switches:
ON = 1
OFF = 0
Default
SW1=11111101
SW2=10011111
SW3=11001000 (8X) (2:1)
SW4=11110011
SW3=X000XXXX == CORE:CCB 4:1
X001XXXX == CORE:CCB 9:2
X010XXXX == CORE:CCB 1:1
X011XXXX == CORE:CCB 3:2
X100XXXX == CORE:CCB 2:1
X101XXXX == CORE:CCB 5:2
X110XXXX == CORE:CCB 3:1
X111XXXX == CORE:CCB 7:2
XXXX0000 == CCB:SYSCLK 16:1
XXXX0001 == RESERVED
XXXX0010 == CCB:SYSCLK 2:1
XXXX0011 == CCB:SYSCLK 3:1
XXXX0100 == CCB:SYSCLK 4:1
XXXX0101 == CCB:SYSCLK 5:1
XXXX0110 == CCB:SYSCLK 6:1
XXXX0111 == RESERVED
XXXX1000 == CCB:SYSCLK 8:1
XXXX1001 == CCB:SYSCLK 9:1
XXXX1010 == CCB:SYSCLK 10:1
XXXX1011 == RESERVED
XXXX1100 == CCB:SYSCLK 12:1
XXXX1101 == CCB:SYSCLK 20:1
XXXX1110 == RESERVED
XXXX1111 == RESERVED
eDINK Info
----------

View File

@ -81,21 +81,27 @@ typedef struct ccsr_ddr {
uint cs1_config; /* 0x2084 - DDR Chip Select Configuration */
uint cs2_config; /* 0x2088 - DDR Chip Select Configuration */
uint cs3_config; /* 0x208c - DDR Chip Select Configuration */
char res5[120];
char res5[112];
uint ext_refrec; /* 0x2100 - DDR SDRAM Extended Refresh Recovery */
uint timing_cfg_0; /* 0x2104 - DDR SDRAM Timing Configuration Register 0 */
uint timing_cfg_1; /* 0x2108 - DDR SDRAM Timing Configuration Register 1 */
uint timing_cfg_2; /* 0x210c - DDR SDRAM Timing Configuration Register 2 */
uint sdram_cfg; /* 0x2110 - DDR SDRAM Control Configuration */
char res6[4];
uint sdram_cfg_2; /* 0x2114 - DDR SDRAM Control Configuration 2 */
uint sdram_mode; /* 0x2118 - DDR SDRAM Mode Configuration */
char res7[8];
uint sdram_mode_2; /* 0x211c - DDR SDRAM Mode Configuration 2*/
uint sdram_md_cntl; /* 0x2120 - DDR SDRAM Mode Control */
uint sdram_interval; /* 0x2124 - DDR SDRAM Interval Configuration */
#ifdef MPC85xx_DDR_SDRAM_CLK_CNTL
char res7_5[8];
uint sdram_data_init; /* 0x2128 - DDR SDRAM Data initialization */
char res6[4];
uint sdram_clk_cntl; /* 0x2130 - DDR SDRAM Clock Control */
char res8[3276];
#else
char res8[3288];
#endif
char res7[20];
uint init_address; /* 0x2148 - DDR training initialization address */
uint init_ext_address; /* 0x214C - DDR training initialization extended address */
char res8_1[2728];
uint ip_rev1; /* 0x2BF8 - DDR IP Block Revision 1 */
uint ip_rev2; /* 0x2BFC - DDR IP Block Revision 2 */
char res8_2[512];
uint data_err_inject_hi; /* 0x2e00 - DDR Memory Data Path Error Injection Mask High */
uint data_err_inject_lo; /* 0x2e04 - DDR Memory Data Path Error Injection Mask Low */
uint ecc_err_inject; /* 0x2e08 - DDR Memory Data Path Error Injection Mask ECC */
@ -120,6 +126,8 @@ typedef struct ccsr_ddr {
} ccsr_ddr_t;
/* I2C Registers(0x3000-0x4000) */
typedef struct ccsr_i2c {
@ -158,6 +166,7 @@ typedef struct ccsr_i2c {
#if defined(CONFIG_MPC8540) \
|| defined(CONFIG_MPC8541) \
|| defined(CONFIG_MPC8548) \
|| defined(CONFIG_MPC8555)
/* DUART Registers(0x4000-0x5000) */
typedef struct ccsr_duart {
@ -1547,7 +1556,13 @@ typedef struct ccsr_gur {
uint ddrdllcr; /* 0xe0e10 - DDR DLL control register */
char res12[12];
uint lbcdllcr; /* 0xe0e20 - LBC DLL control register */
char res13[61915];
char res13[248];
uint lbiuiplldcr0; /* 0xe0f1c -- LBIU PLL Debug Reg 0 */
uint lbiuiplldcr1; /* 0xe0f20 -- LBIU PLL Debug Reg 1 */
uint ddrioovcr; /* 0xe0f24 - DDR IO Override Control */
uint res14; /* 0xe0f28 */
uint tsec34ioovcr; /* 0xe0f2c - eTSEC 3/4 IO override control */
char res15[61651];
} ccsr_gur_t;
typedef struct immap {

View File

@ -420,6 +420,7 @@
#define SPRN_MAS4 0x274 /* MMU Assist Register 4 */
#define SPRN_MAS5 0x275 /* MMU Assist Register 5 */
#define SPRN_MAS6 0x276 /* MMU Assist Register 6 */
#define SPRN_MAS7 0x3B0 /* MMU Assist Register 7 */
#define SPRN_IVOR32 0x210 /* Interrupt Vector Offset Register 32 */
#define SPRN_IVOR33 0x211 /* Interrupt Vector Offset Register 33 */
@ -584,6 +585,7 @@
#define MAS4 SPRN_MAS4
#define MAS5 SPRN_MAS5
#define MAS6 SPRN_MAS6
#define MAS7 SPRN_MAS7
/* Device Control Registers */
@ -792,6 +794,8 @@
#define SVR_8560 0x8070
#define SVR_8555 0x8079
#define SVR_8541 0x807A
#define SVR_8548 0x8031
#define SVR_8548_E 0x8039
/* I am just adding a single entry for 8260 boards. I think we may be

View File

@ -49,10 +49,12 @@
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
/*
* sysclk for MPC85xx
@ -342,7 +344,9 @@
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC1 1
#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
#define CONFIG_MPC85XX_TSEC2 1
#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
@ -351,11 +355,13 @@
#if CONFIG_HAS_FEC
#define CONFIG_MPC85XX_FEC 1
#define CONFIG_MPC85XX_FEC_NAME "FEC"
#define FEC_PHY_ADDR 3
#define FEC_PHYIDX 0
#endif
#define CONFIG_ETHPRIME "MOTO ENET0"
/* Options are: TSEC[0-1], FEC */
#define CONFIG_ETHPRIME "TSEC0"
#endif /* CONFIG_TSEC_ENET */

View File

@ -41,9 +41,12 @@
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
/*
* When initializing flash, if we cannot find the manufacturer ID,
@ -360,7 +363,9 @@ extern unsigned long get_clock_freq(void);
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC1 1
#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
#define CONFIG_MPC85XX_TSEC2 1
#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
@ -368,7 +373,9 @@ extern unsigned long get_clock_freq(void);
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define FEC_PHYIDX 0
#define CONFIG_ETHPRIME "MOTO ENET0"
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#endif /* CONFIG_TSEC_ENET */

View File

@ -0,0 +1,521 @@
/*
* Copyright 2004 Freescale Semiconductor.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* mpc8548cds board configuration file
*
* Please refer to doc/README.mpc85xxcds for more info.
*
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* High Level Configuration Options */
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */
#define CONFIG_MPC8548 1 /* MPC8548 specific */
#define CONFIG_MPC8548CDS 1 /* MPC8548CDS board specific */
#undef CONFIG_PCI
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
/*
* When initializing flash, if we cannot find the manufacturer ID,
* assume this is the AMD flash associated with the CDS board.
* This allows booting from a promjet.
*/
#define CONFIG_ASSUME_AMD_FLASH
#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */
#ifndef __ASSEMBLY__
extern unsigned long get_clock_freq(void);
#endif
#define CONFIG_SYS_CLK_FREQ get_clock_freq() /* sysclk for MPC85xx */
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
/*
* Only possible on E500 Version 2 or newer cores.
*/
#define CONFIG_ENABLE_36BIT_PHYS 1
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
#define CFG_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
/*
* DDR Setup
*/
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
/*
* Make sure required options are set
*/
#ifndef CONFIG_SPD_EEPROM
#error ("CONFIG_SPD_EEPROM is required")
#endif
#undef CONFIG_CLOCKS_IN_MHZ
/*
* Local Bus Definitions
*/
/*
* FLASH on the Local Bus
* Two banks, 8M each, using the CFI driver.
* Boot from BR0/OR0 bank at 0xff00_0000
* Alternate BR1/OR1 bank at 0xff80_0000
*
* BR0, BR1:
* Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
* Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
* Port Size = 16 bits = BRx[19:20] = 10
* Use GPCM = BRx[24:26] = 000
* Valid = BRx[31] = 1
*
* 0 4 8 12 16 20 24 28
* 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0
* 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1
*
* OR0, OR1:
* Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
* Reserved ORx[17:18] = 11, confusion here?
* CSNT = ORx[20] = 1
* ACS = half cycle delay = ORx[21:22] = 11
* SCY = 6 = ORx[24:27] = 0110
* TRLX = use relaxed timing = ORx[29] = 1
* EAD = use external address latch delay = OR[31] = 1
*
* 0 4 8 12 16 20 24 28
* 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx
*/
#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 8M */
#define CFG_BR0_PRELIM 0xff801001
#define CFG_BR1_PRELIM 0xff001001
#define CFG_OR0_PRELIM 0xff806e65
#define CFG_OR1_PRELIM 0xff806e65
#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE}
#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#define CFG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
/*
* SDRAM on the Local Bus
*/
#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
/*
* Base Register 2 and Option Register 2 configure SDRAM.
* The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
*
* For BR2, need:
* Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
* port-size = 32-bits = BR2[19:20] = 11
* no parity checking = BR2[21:22] = 00
* SDRAM for MSEL = BR2[24:26] = 011
* Valid = BR[31] = 1
*
* 0 4 8 12 16 20 24 28
* 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
*
* FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
* FIXME: the top 17 bits of BR2.
*/
#define CFG_BR2_PRELIM 0xf0001861
/*
* The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
*
* For OR2, need:
* 64MB mask for AM, OR2[0:7] = 1111 1100
* XAM, OR2[17:18] = 11
* 9 columns OR2[19-21] = 010
* 13 rows OR2[23-25] = 100
* EAD set for extra time OR[31] = 1
*
* 0 4 8 12 16 20 24 28
* 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
*/
#define CFG_OR2_PRELIM 0xfc006901
#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */
#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
#define CFG_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
/*
* LSDMR masks
*/
#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
/*
* Common settings for all Local Bus SDRAM commands.
* At run time, either BSMA1516 (for CPU 1.1)
* or BSMA1617 (for CPU 1.0) (old)
* is OR'ed in too.
*/
#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFCR16 \
| CFG_LBC_LSDMR_PRETOACT7 \
| CFG_LBC_LSDMR_ACTTORW7 \
| CFG_LBC_LSDMR_BL8 \
| CFG_LBC_LSDMR_WRC4 \
| CFG_LBC_LSDMR_CL3 \
| CFG_LBC_LSDMR_RFEN \
)
/*
* The CADMUS registers are connected to CS3 on CDS.
* The new memory map places CADMUS at 0xf8000000.
*
* For BR3, need:
* Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
* port-size = 8-bits = BR[19:20] = 01
* no parity checking = BR[21:22] = 00
* GPMC for MSEL = BR[24:26] = 000
* Valid = BR[31] = 1
*
* 0 4 8 12 16 20 24 28
* 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
*
* For OR3, need:
* 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0
* disable buffer ctrl OR[19] = 0
* CSNT OR[20] = 1
* ACS OR[21:22] = 11
* XACS OR[23] = 1
* SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe
* SETA OR[28] = 0
* TRLX OR[29] = 1
* EHTR OR[30] = 1
* EAD extra time OR[31] = 1
*
* 0 4 8 12 16 20 24 28
* 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
*/
#define CADMUS_BASE_ADDR 0xf8000000
#define CFG_BR3_PRELIM 0xf8000801
#define CFG_OR3_PRELIM 0xfff00ff7
#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK 1
#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 2
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550
#define CFG_NS16550_SERIAL
#define CFG_NS16550_REG_SIZE 1
#define CFG_NS16550_CLK get_bus_freq(0)
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
/* I2C */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_EEPROM_ADDR 0x57
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
#define CFG_PCI1_IO_BASE 0xe2000000
#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
#define CFG_PCI2_MEM_BASE 0xa0000000
#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
#define CFG_PCI2_IO_BASE 0xe3000000
#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE
#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
#if defined(CONFIG_PCI)
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR 0xe0000000
#define PCI_ENET0_MEMADDR 0xe0000000
#define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/
#endif
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI 1
#endif
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC1 1
#define CONFIG_MPC85XX_TSEC1_NAME "eTSEC0"
#define CONFIG_MPC85XX_TSEC2 1
#define CONFIG_MPC85XX_TSEC2_NAME "eTSEC1"
#define CONFIG_MPC85XX_TSEC3 1
#define CONFIG_MPC85XX_TSEC3_NAME "eTSEC2"
#define CONFIG_MPC85XX_TSEC4 1
#define CONFIG_MPC85XX_TSEC4_NAME "eTSEC3"
#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC3_PHY_ADDR 2
#define TSEC4_PHY_ADDR 3
#define FEC_PHY_ADDR 3
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
#define TSEC4_PHYIDX 0
#define FEC_PHYIDX 0
/* Options are: eTSEC[0-3] */
#define CONFIG_ETHPRIME "eTSEC0"
#endif /* CONFIG_TSEC_ENET */
/*
* Environment
*/
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
#define CFG_ENV_SIZE 0x2000
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#if defined(CONFIG_PCI)
#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
| CFG_CMD_PCI \
| CFG_CMD_PING \
| CFG_CMD_I2C \
| CFG_CMD_MII)
#else
#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
| CFG_CMD_PING \
| CFG_CMD_I2C \
| CFG_CMD_MII)
#endif
#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/* Cache Configuration */
#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
#endif
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Environment Configuration
*/
/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
#define CONFIG_HAS_ETH2
#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
#endif
#define CONFIG_IPADDR 192.168.1.253
#define CONFIG_HOSTNAME unknown
#define CONFIG_ROOTPATH /nfsroot
#define CONFIG_BOOTFILE your.uImage
#define CONFIG_SERVERIP 192.168.1.1
#define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
#define CONFIG_BAUDRATE 115200
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS1\0" \
"ramdiskaddr=400000\0" \
"ramdiskfile=your.ramdisk.u-boot\0"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"bootm $loadaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"bootm $loadaddr $ramdiskaddr"
#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
#endif /* __CONFIG_H */

View File

@ -41,9 +41,12 @@
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
/*
* When initializing flash, if we cannot find the manufacturer ID,
@ -360,7 +363,9 @@ extern unsigned long get_clock_freq(void);
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC1 1
#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
#define CONFIG_MPC85XX_TSEC2 1
#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
@ -368,7 +373,9 @@ extern unsigned long get_clock_freq(void);
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define FEC_PHYIDX 0
#define CONFIG_ETHPRIME "MOTO ENET0"
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#endif /* CONFIG_TSEC_ENET */

View File

@ -46,10 +46,12 @@
#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
/*
* sysclk for MPC85xx
@ -337,13 +339,17 @@
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC1 1
#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
#define CONFIG_MPC85XX_TSEC2 1
#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define CONFIG_ETHPRIME "MOTO ENET0"
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */

View File

@ -45,10 +45,12 @@
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
/*
* sysclk for MPC85xx
@ -250,17 +252,21 @@
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC1 1
#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
#define CONFIG_MPC85XX_TSEC2 1
#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
#define TSEC1_PHY_ADDR 2
#define TSEC2_PHY_ADDR 3
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define CONFIG_MPC85XX_FEC 1
#define CONFIG_MPC85XX_FEC_NAME "FEC"
#define FEC_PHY_ADDR 1
#define FEC_PHYIDX 0
#define CONFIG_ETHPRIME "MOTO ENET0"
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#define CONFIG_HAS_ETH1 1
#define CONFIG_HAS_ETH2 1

View File

@ -227,10 +227,14 @@
#if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */
#define CONFIG_NET_MULTI 1
#define CONFIG_PHY_BCM5421S /* GigaBit Ether PHY */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 25 /* PHY address */
# define CONFIG_NET_MULTI 1
# define CONFIG_MPC85xx_TSEC1
# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0"
# define CONFIG_MII 1 /* MII PHY management */
# define TSEC1_PHY_ADDR 25
# define TSEC1_PHYIDX 0
/* Options are: TSEC0 */
# define CONFIG_ETHPRIME "TSEC0"
#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */

View File

@ -215,10 +215,14 @@
#if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */
#define CONFIG_NET_MULTI 1
#define CONFIG_PHY_BCM5421S /* GigaBit Ether PHY */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 25 /* PHY address */
# define CONFIG_NET_MULTI 1
# define CONFIG_MII 1 /* MII PHY management */
# define CONFIG_MPC85xx_TSEC1
# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0"
# define TSEC1_PHY_ADDR 25
# define TSEC1_PHYIDX 0
/* Options are: TSEC0 */
# define CONFIG_ETHPRIME "TSEC0"
#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */

View File

@ -280,20 +280,24 @@
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC1 1
#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
#define CONFIG_MPC85XX_TSEC2 1
#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define CONFIG_MPC85XX_FEC 1
#define CONFIG_MPC85XX_FEC_NAME "FEC"
#define FEC_PHY_ADDR 2
#define FEC_PHYIDX 0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
#define CONFIG_ETHPRIME "ENET1"
/* Options are TSEC[0-1], FEC */
#define CONFIG_ETHPRIME "TSEC1"
#endif /* CONFIG_TSEC_ENET */

View File

@ -276,6 +276,7 @@
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC2 1
#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
#define TSEC2_PHY_ADDR 1
#define TSEC2_PHYIDX 0
@ -288,7 +289,7 @@
#define CFG_CPMFCR_RAMTYPE 0
#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
#define CONFIG_ETHPRIME "ENET1"
#define CONFIG_ETHPRIME "TSEC1"
/*
* Environment

View File

@ -210,10 +210,14 @@
#if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */
#define CONFIG_NET_MULTI 1
#define CONFIG_PHY_BCM5421S 1 /* GigaBit Ether PHY */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 25 /* PHY address */
# define CONFIG_NET_MULTI 1
# define CONFIG_MII 1 /* MII PHY management */
# define CONFIG_MPC85xx_TSEC1
# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0"
# define TSEC1_PHY_ADDR 25
# define TSEC1_PHYIDX 0
/* Options are: TSEC0 */
# define CONFIG_ETHPRIME "TSEC0"
#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */

View File

@ -227,14 +227,16 @@
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC1 1
#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
#define CONFIG_MPC85XX_TSEC2 1
#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
#undef CONFIG_MPS85XX_FEC
#define TSEC1_PHY_ADDR 2
#define TSEC2_PHY_ADDR 4
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define CONFIG_ETHPRIME "MOTO ENET0"
#define CONFIG_ETHPRIME "TSEC0"
#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */

View File

@ -25,54 +25,84 @@
#define _SPD_H_
typedef struct spd_eeprom_s {
unsigned char info_size; /* # of bytes written into serial memory */
unsigned char chip_size; /* Total # of bytes of SPD memory device */
unsigned char mem_type; /* Fundamental memory type (FPM, EDO, SDRAM...) */
unsigned char nrow_addr; /* # of Row Addresses on this assembly */
unsigned char ncol_addr; /* # of Column Addresses on this assembly */
unsigned char nrows; /* # of Module Rows on this assembly */
unsigned char dataw_lsb; /* Data Width of this assembly */
unsigned char dataw_msb; /* ... Data Width continuation */
unsigned char voltage; /* Voltage interface standard of this assembly */
unsigned char clk_cycle; /* SDRAM Cycle time at CL=X */
unsigned char clk_access; /* SDRAM Access from Clock at CL=X */
unsigned char config; /* DIMM Configuration type (non-parity, ECC) */
unsigned char refresh; /* Refresh Rate/Type */
unsigned char primw; /* Primary SDRAM Width */
unsigned char ecw; /* Error Checking SDRAM width */
unsigned char min_delay; /* Min Clock Delay for Back to Back Random Address */
unsigned char burstl; /* Burst Lengths Supported */
unsigned char nbanks; /* # of Banks on Each SDRAM Device */
unsigned char cas_lat; /* CAS# Latencies Supported */
unsigned char cs_lat; /* CS# Latency */
unsigned char write_lat; /* Write Latency (also called Write Recovery time) */
unsigned char mod_attr; /* SDRAM Module Attributes */
unsigned char dev_attr; /* SDRAM Device Attributes */
unsigned char clk_cycle2; /* Min SDRAM Cycle time at CL=X-1 */
unsigned char clk_access2; /* SDRAM Access from Clock at CL=X-1 */
unsigned char clk_cycle3; /* Min SDRAM Cycle time at CL=X-2 */
unsigned char clk_access3; /* Max SDRAM Access from Clock at CL=X-2 */
unsigned char trp; /* Min Row Precharge Time (tRP) */
unsigned char trrd; /* Min Row Active to Row Active (tRRD) */
unsigned char trcd; /* Min RAS to CAS Delay (tRCD) */
unsigned char tras; /* Minimum RAS Pulse Width (tRAS) */
unsigned char row_dens; /* Density of each row on module */
unsigned char ca_setup; /* Command and Address signal input setup time */
unsigned char ca_hold; /* Command and Address signal input hold time */
unsigned char data_setup; /* Data signal input setup time */
unsigned char data_hold; /* Data signal input hold time */
unsigned char sset[26]; /* Superset Information (may be used in future) */
unsigned char spd_rev; /* SPD Data Revision Code */
unsigned char cksum; /* Checksum for bytes 0-62 */
unsigned char mid[8]; /* Manufacturer's JEDEC ID code per JEP-108E */
unsigned char mloc; /* Manufacturing Location */
unsigned char mpart[18]; /* Manufacturer's Part Number */
unsigned char rev[2]; /* Revision Code */
unsigned char mdate[2]; /* Manufacturing Date */
unsigned char sernum[4]; /* Assembly Serial Number */
unsigned char mspec[27]; /* Manufacturer Specific Data */
unsigned char freq; /* Intel specification frequency */
unsigned char intel_cas; /* Intel Specification CAS# Latency support */
unsigned char info_size; /* 0 # bytes written into serial memory */
unsigned char chip_size; /* 1 Total # bytes of SPD memory device */
unsigned char mem_type; /* 2 Fundamental memory type */
unsigned char nrow_addr; /* 3 # of Row Addresses on this assembly */
unsigned char ncol_addr; /* 4 # of Column Addrs on this assembly */
unsigned char nrows; /* 5 # of Module Rows on this assembly */
unsigned char dataw_lsb; /* 6 Data Width of this assembly */
unsigned char dataw_msb; /* 7 ... Data Width continuation */
unsigned char voltage; /* 8 Voltage intf std of this assembly */
unsigned char clk_cycle; /* 9 SDRAM Cycle time at CL=X */
unsigned char clk_access; /* 10 SDRAM Access from Clock at CL=X */
unsigned char config; /* 11 DIMM Configuration type */
unsigned char refresh; /* 12 Refresh Rate/Type */
unsigned char primw; /* 13 Primary SDRAM Width */
unsigned char ecw; /* 14 Error Checking SDRAM width */
unsigned char min_delay; /* 15 for Back to Back Random Address */
unsigned char burstl; /* 16 Burst Lengths Supported */
unsigned char nbanks; /* 17 # of Banks on Each SDRAM Device */
unsigned char cas_lat; /* 18 CAS# Latencies Supported */
unsigned char cs_lat; /* 19 CS# Latency */
unsigned char write_lat; /* 20 Write Latency (aka Write Recovery) */
unsigned char mod_attr; /* 21 SDRAM Module Attributes */
unsigned char dev_attr; /* 22 SDRAM Device Attributes */
unsigned char clk_cycle2; /* 23 Min SDRAM Cycle time at CL=X-1 */
unsigned char clk_access2; /* 24 SDRAM Access from Clock at CL=X-1 */
unsigned char clk_cycle3; /* 25 Min SDRAM Cycle time at CL=X-2 */
unsigned char clk_access3; /* 26 Max Access from Clock at CL=X-2 */
unsigned char trp; /* 27 Min Row Precharge Time (tRP)*/
unsigned char trrd; /* 28 Min Row Active to Row Active (tRRD) */
unsigned char trcd; /* 29 Min RAS to CAS Delay (tRCD) */
unsigned char tras; /* 30 Minimum RAS Pulse Width (tRAS) */
unsigned char row_dens; /* 31 Density of each row on module */
unsigned char ca_setup; /* 32 Cmd + Addr signal input setup time */
unsigned char ca_hold; /* 33 Cmd and Addr signal input hold time */
unsigned char data_setup; /* 34 Data signal input setup time */
unsigned char data_hold; /* 35 Data signal input hold time */
unsigned char twr; /* 36 Write Recovery time tWR */
unsigned char twtr; /* 37 Int write to read delay tWTR */
unsigned char trtp; /* 38 Int read to precharge delay tRTP */
unsigned char mem_probe; /* 39 Mem analysis probe characteristics */
unsigned char trctrfc_ext; /* 40 Extensions to trc and trfc */
unsigned char trc; /* 41 Min Active to Auto refresh time tRC */
unsigned char trfc; /* 42 Min Auto to Active period tRFC */
unsigned char tckmax; /* 43 Max device cycle time tCKmax */
unsigned char tdqsq; /* 44 Max DQS to DQ skew */
unsigned char tqhs; /* 45 Max Read DataHold skew tQHS */
unsigned char pll_relock; /* 46 PLL Relock time */
unsigned char res[15]; /* 47-xx IDD in SPD and Reserved space */
unsigned char spd_rev; /* 62 SPD Data Revision Code */
unsigned char cksum; /* 63 Checksum for bytes 0-62 */
unsigned char mid[8]; /* 64 Mfr's JEDEC ID code per JEP-108E */
unsigned char mloc; /* 72 Manufacturing Location */
unsigned char mpart[18]; /* 73 Manufacturer's Part Number */
unsigned char rev[2]; /* 91 Revision Code */
unsigned char mdate[2]; /* 93 Manufacturing Date */
unsigned char sernum[4]; /* 95 Assembly Serial Number */
unsigned char mspec[27]; /* 99 Manufacturer Specific Data */
/*
* Open for Customer Use starting with byte 128.
*/
unsigned char freq; /* 128 Intel spec: frequency */
unsigned char intel_cas; /* 129 Intel spec: CAS# Latency support */
} spd_eeprom_t;
/*
* Byte 2 Fundamental Memory Types.
*/
#define SPD_MEMTYPE_FPM (0x01)
#define SPD_MEMTYPE_EDO (0x02)
#define SPD_MEMTYPE_PIPE_NIBBLE (0x03)
#define SPD_MEMTYPE_SDRAM (0x04)
#define SPD_MEMTYPE_ROM (0x05)
#define SPD_MEMTYPE_SGRAM (0x06)
#define SPD_MEMTYPE_DDR (0x07)
#define SPD_MEMTYPE_DDR2 (0x08)
#endif /* _SPD_H_ */

View File

@ -52,7 +52,7 @@ extern int rtl8139_initialize(bd_t*);
extern int rtl8169_initialize(bd_t*);
extern int scc_initialize(bd_t*);
extern int skge_initialize(bd_t*);
extern int tsec_initialize(bd_t*, int);
extern int tsec_initialize(bd_t*, int, char *);
static struct eth_device *eth_devices, *eth_current;
@ -155,13 +155,20 @@ int eth_initialize(bd_t *bis)
skge_initialize(bis);
#endif
#if defined(CONFIG_MPC85XX_TSEC1)
tsec_initialize(bis, 0);
tsec_initialize(bis, 0, CONFIG_MPC85XX_TSEC1_NAME);
#endif
#if defined(CONFIG_MPC85XX_TSEC2)
tsec_initialize(bis, 1);
tsec_initialize(bis, 1, CONFIG_MPC85XX_TSEC2_NAME);
#endif
#if defined(CONFIG_MPC85XX_FEC)
tsec_initialize(bis, 2);
tsec_initialize(bis, 2, CONFIG_MPC85XX_FEC_NAME);
#else
# if defined(CONFIG_MPC85XX_TSEC3)
tsec_initialize(bis, 2, CONFIG_MPC85XX_TSEC3_NAME);
# endif
# if defined(CONFIG_MPC85XX_TSEC4)
tsec_initialize(bis, 3, CONFIG_MPC85XX_TSEC4_NAME);
# endif
#endif
#if defined(CONFIG_AU1X00)
au1x00_enet_initialize(bis);