phone-side
/
uboot-mt623x
9
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity

Migrate esd 405EP boards to new NAND subsystem 

Migrate esd 405EP boards to new NAND subsystem

-cleanup
-use correct io accessors (in/out_be32())

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This commit is contained in:
Matthias Fuchs 2007-07-09 10:10:06 +02:00 committed by Stefan Roese
parent e09f7ab574
commit bd84ee4c20
21 changed files with 114 additions and 450 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

4
board/esd/ash405/Makefile
View File

@ -28,7 +28,9 @@ endif
LIB = $(obj)lib$(BOARD).a
COBJS = $(BOARD).o flash.o ../common/misc.o
COBJS = $(BOARD).o flash.o \
../common/misc.o \
../common/esd405ep_nand.o \
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))

43
board/esd/ash405/ash405.c
View File

@ -23,6 +23,7 @@
#include <common.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <command.h>
#include <malloc.h>
@ -33,6 +34,7 @@
#endif
extern int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
extern void lxt971_no_sleep(void);
/* fpga configuration data - gzip compressed and generated by bin2c */
const unsigned char fpgadata[] =
@ -164,17 +166,11 @@ int misc_init_r (void)
/*
* Reset external DUARTs
*/
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_DUART_RST); /* set reset to high */
out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_DUART_RST);
udelay(10); /* wait 10us */
out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */
out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_DUART_RST);
udelay(1000); /* wait 1ms */
/*
* Set NAND-FLASH GPIO signals to default
*/
out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
/*
* Enable interrupts in exar duart mcr[3]
*/
@ -218,35 +214,18 @@ long int initdram (int board_type)
mtdcr(memcfga, mem_mb0cf);
val = mfdcr(memcfgd);
#if 0
printf("\nmb0cf=%x\n", val); /* test-only */
printf("strap=%x\n", mfdcr(strap)); /* test-only */
#endif
return (4*1024*1024 << ((val & 0x000e0000) >> 17));
}
/* ------------------------------------------------------------------------- */
int testdram (void)
void reset_phy(void)
{
/* TODO: XXX XXX XXX */
printf ("test: 16 MB - ok\n");
#ifdef CONFIG_LXT971_NO_SLEEP
return (0);
}
/* ------------------------------------------------------------------------- */
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
#include <linux/mtd/nand_legacy.h>
extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
void nand_init(void)
{
nand_probe(CFG_NAND_BASE);
if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
print_size(nand_dev_desc[0].totlen, "\n");
}
}
/*
* Disable sleep mode in LXT971
*/
lxt971_no_sleep();
#endif
}

5
board/esd/cms700/Makefile
View File

@ -33,7 +33,10 @@ CPLD = ../common/xilinx_jtag/lenval.o \
../common/xilinx_jtag/micro.o \
../common/xilinx_jtag/ports.o
COBJS = $(BOARD).o flash.o ../common/misc.o $(CPLD)
COBJS = $(BOARD).o flash.o \
../common/misc.o \
$(CPLD) \
../common/esd405ep_nand.o \
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))

39
board/esd/cms700/cms700.c
View File

@ -1,5 +1,5 @@
/*
* (C) Copyright 2005
* (C) Copyright 2005-2007
* Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com
*
* See file CREDITS for list of people who contributed to this
@ -23,6 +23,7 @@
#include <common.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <command.h>
#include <malloc.h>
@ -68,9 +69,9 @@ int board_early_init_f (void)
/*
* Reset CPLD via GPIO12 (CS3) pin
*/
out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_PLD_RESET);
out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_PLD_RESET);
udelay(1000); /* wait 1ms */
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_PLD_RESET);
out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_PLD_RESET);
udelay(1000); /* wait 1ms */
return 0;
@ -94,13 +95,7 @@ int misc_init_r (void)
/*
* Setup and enable EEPROM write protection
*/
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_EEPROM_WP);
/*
* Set NAND-FLASH GPIO signals to default
*/
out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_EEPROM_WP);
return (0);
}
@ -153,11 +148,6 @@ long int initdram (int board_type)
mtdcr(memcfga, mem_mb0cf);
val = mfdcr(memcfgd);
#if 0
printf("\nmb0cf=%x\n", val); /* test-only */
printf("strap=%x\n", mfdcr(strap)); /* test-only */
#endif
return (4*1024*1024 << ((val & 0x000e0000) >> 17));
}
@ -180,17 +170,17 @@ int eeprom_write_enable (unsigned dev_addr, int state)
switch (state) {
case 1:
/* Enable write access, clear bit GPIO_SINT2. */
out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_EEPROM_WP);
out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_EEPROM_WP);
state = 0;
break;
case 0:
/* Disable write access, set bit GPIO_SINT2. */
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_EEPROM_WP);
out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_EEPROM_WP);
state = 0;
break;
default:
/* Read current status back. */
state = (0 == (in32(GPIO0_OR) & CFG_EEPROM_WP));
state = (0 == (in_be32((void *)GPIO0_OR) & CFG_EEPROM_WP));
break;
}
}
@ -235,19 +225,6 @@ U_BOOT_CMD(eepwren, 2, 0, do_eep_wren,
/* ------------------------------------------------------------------------- */
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
#include <linux/mtd/nand_legacy.h>
extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
void nand_init(void)
{
nand_probe(CFG_NAND_BASE);
if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
print_size(nand_dev_desc[0].totlen, "\n");
}
}
#endif
void reset_phy(void)
{
#ifdef CONFIG_LXT971_NO_SLEEP

5
board/esd/hh405/Makefile
View File

@ -28,7 +28,10 @@ endif
LIB = $(obj)lib$(BOARD).a
COBJS = $(BOARD).o flash.o ../common/misc.o ../common/auto_update.o
COBJS = $(BOARD).o flash.o \
../common/misc.o \
../common/esd405ep_nand.o \
../common/auto_update.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))

22
board/esd/hh405/hh405.c
View File

@ -5,7 +5,7 @@
* (C) Copyright 2005
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* (C) Copyright 2006
* (C) Copyright 2006-2007
* Matthias Fuchs, esd GmbH, matthias.fuchs@esd-electronics.com
*
* See file CREDITS for list of people who contributed to this
@ -476,12 +476,6 @@ int misc_init_r (void)
*/
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_EEPROM_WP);
/*
* Set NAND-FLASH GPIO signals to default
*/
out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
/*
* Reset touch-screen controller
*/
@ -690,20 +684,6 @@ void ide_set_reset(int on)
#endif /* CONFIG_IDE_RESET */
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
#include <linux/mtd/nand_legacy.h>
extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
void nand_init(void)
{
nand_probe(CFG_NAND_BASE);
if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
print_size(nand_dev_desc[0].totlen, "\n");
}
}
#endif
#if defined(CFG_EEPROM_WREN)
/* Input: <dev_addr> I2C address of EEPROM device to enable.
* <state> -1: deliver current state

4
board/esd/hub405/Makefile
View File

@ -28,7 +28,9 @@ endif
LIB = $(obj)lib$(BOARD).a
COBJS = $(BOARD).o flash.o ../common/misc.o
COBJS = $(BOARD).o flash.o \
../common/misc.o \
../common/esd405ep_nand.o \
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))

34
board/esd/hub405/hub405.c
View File

@ -152,12 +152,6 @@ int misc_init_r (void)
out32(GPIO0_OR, val);
/*
* Set NAND-FLASH GPIO signals to default
*/
out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
/*
* check board type and setup AP power
*/
@ -242,33 +236,5 @@ long int initdram (int board_type)
mtdcr(memcfga, mem_mb0cf);
val = mfdcr(memcfgd);
#if 0
printf("\nmb0cf=%x\n", val); /* test-only */
printf("strap=%x\n", mfdcr(strap)); /* test-only */
#endif
return (4*1024*1024 << ((val & 0x000e0000) >> 17));
}
int testdram (void)
{
/* TODO: XXX XXX XXX */
printf ("test: 16 MB - ok\n");
return (0);
}
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
#include <linux/mtd/nand_legacy.h>
extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
void nand_init(void)
{
nand_probe(CFG_NAND_BASE);
if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
print_size(nand_dev_desc[0].totlen, "\n");
}
}
#endif

5
board/esd/plu405/Makefile
View File

@ -28,7 +28,10 @@ endif
LIB = $(obj)lib$(BOARD).a
COBJS = $(BOARD).o flash.o ../common/misc.o ../common/auto_update.o
COBJS = $(BOARD).o flash.o \
../common/misc.o \
../common/esd405ep_nand.o \
../common/auto_update.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))

56
board/esd/plu405/plu405.c
View File

@ -23,6 +23,7 @@
#include <common.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <command.h>
#include <malloc.h>
@ -31,6 +32,8 @@
#define FPGA_DEBUG
#endif
DECLARE_GLOBAL_DATA_PTR;
extern int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
extern void lxt971_no_sleep(void);
@ -114,6 +117,10 @@ int misc_init_r (void)
int index;
int i;
/* adjust flash start and offset */
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
gd->bd->bi_flashoffset = 0;
dst = malloc(CFG_FPGA_MAX_SIZE);
if (gunzip (dst, CFG_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
printf ("GUNZIP ERROR - must RESET board to recover\n");
@ -177,17 +184,11 @@ int misc_init_r (void)
/*
* Reset external DUARTs
*/
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_DUART_RST); /* set reset to high */
out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_DUART_RST);
udelay(10); /* wait 10us */
out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */
out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_DUART_RST);
udelay(1000); /* wait 1ms */
/*
* Set NAND-FLASH GPIO signals to default
*/
out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
/*
* Enable interrupts in exar duart mcr[3]
*/
@ -226,24 +227,10 @@ long int initdram (int board_type)
mtdcr(memcfga, mem_mb0cf);
val = mfdcr(memcfgd);
#if 0
printf("\nmb0cf=%x\n", val); /* test-only */
printf("strap=%x\n", mfdcr(strap)); /* test-only */
#endif
return (4*1024*1024 << ((val & 0x000e0000) >> 17));
}
int testdram (void)
{
/* TODO: XXX XXX XXX */
printf ("test: 16 MB - ok\n");
return (0);
}
#ifdef CONFIG_IDE_RESET
void ide_set_reset(int on)
{
@ -262,31 +249,6 @@ void ide_set_reset(int on)
#endif /* CONFIG_IDE_RESET */
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
#include <linux/mtd/nand_legacy.h>
extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
void nand_init(void)
{
nand_probe(CFG_NAND_BASE);
if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
print_size(nand_dev_desc[0].totlen, "\n");
}
}
#endif
#ifdef CONFIG_AUTO_UPDATE_SHOW
void board_auto_update_show(int au_active)
{
if (au_active) {
printf("\n Dies ist die board-funktion: Updating!!!\n");
} else {
printf("\n Dies ist die board-funktion: Updating done!!!\n");
}
}
#endif
void reset_phy(void)
{
#ifdef CONFIG_LXT971_NO_SLEEP

4
board/esd/voh405/Makefile
View File

@ -28,7 +28,9 @@ endif
LIB = $(obj)lib$(BOARD).a
COBJS = $(BOARD).o flash.o ../common/misc.o
COBJS = $(BOARD).o flash.o \
../common/misc.o \
../common/esd405ep_nand.o \
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))

20
board/esd/voh405/voh405.c
View File

@ -194,12 +194,6 @@ int misc_init_r (void)
out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */
udelay(1000); /* wait 1ms */
/*
* Set NAND-FLASH GPIO signals to default
*/
out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
/*
* Enable interrupts in exar duart mcr[3]
*/
@ -340,17 +334,3 @@ void ide_set_reset(int on)
}
}
#endif /* CONFIG_IDE_RESET */
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
#include <linux/mtd/nand_legacy.h>
extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
void nand_init(void)
{
nand_probe(CFG_NAND_BASE);
if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
print_size(nand_dev_desc[0].totlen, "\n");
}
}
#endif

4
board/esd/wuh405/Makefile
View File

@ -28,7 +28,9 @@ endif
LIB = $(obj)lib$(BOARD).a
COBJS = $(BOARD).o flash.o ../common/misc.o
COBJS = $(BOARD).o flash.o \
../common/misc.o \
../common/esd405ep_nand.o \
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))

33
board/esd/wuh405/wuh405.c
View File

@ -169,12 +169,6 @@ int misc_init_r (void)
out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */
udelay(1000); /* wait 1ms */
/*
* Set NAND-FLASH GPIO signals to default
*/
out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
/*
* Enable interrupts in exar duart mcr[3]
*/
@ -218,35 +212,8 @@ long int initdram (int board_type)
mtdcr(memcfga, mem_mb0cf);
val = mfdcr(memcfgd);
#if 0
printf("\nmb0cf=%x\n", val); /* test-only */
printf("strap=%x\n", mfdcr(strap)); /* test-only */
#endif
return (4*1024*1024 << ((val & 0x000e0000) >> 17));
}
/* ------------------------------------------------------------------------- */
int testdram (void)
{
/* TODO: XXX XXX XXX */
printf ("test: 16 MB - ok\n");
return (0);
}
/* ------------------------------------------------------------------------- */
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
#include <linux/mtd/nand_legacy.h>
extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
void nand_init(void)
{
nand_probe(CFG_NAND_BASE);
if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
print_size(nand_dev_desc[0].totlen, "\n");
}
}
#endif

43
include/configs/ASH405.h
View File

@ -53,9 +53,13 @@
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_NET_MULTI 1
#undef CONFIG_HAS_ETH1
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
@ -132,39 +136,16 @@
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
#define NAND_MAX_CHIPS 1
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define NAND_BIG_DELAY_US 25
#define CFG_NAND_LEGACY
#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define SECTORSIZE 512
#define ADDR_COLUMN 1
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
#define CONFIG_MTD_NAND_VERIFY_WRITE 1 /* verify all writes!!! */
#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
/*-----------------------------------------------------------------------

37
include/configs/CMS700.h
View File

@ -81,8 +81,6 @@
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#define CFG_NAND_LEGACY
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
@ -148,34 +146,15 @@
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define SECTORSIZE 512
#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
#define NAND_MAX_CHIPS 1
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define NAND_BIG_DELAY_US 25
#define ADDR_COLUMN 1
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */

37
include/configs/HH405.h
View File

@ -130,8 +130,6 @@
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#define CFG_NAND_LEGACY
#undef CONFIG_BZIP2 /* include support for bzip2 compressed images */
#undef CONFIG_WATCHDOG /* watchdog disabled */
@ -198,34 +196,15 @@
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define SECTORSIZE 512
#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
#define NAND_MAX_CHIPS 1
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define NAND_BIG_DELAY_US 25
#define ADDR_COLUMN 1
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */

37
include/configs/HUB405.h
View File

@ -135,36 +135,15 @@
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
#define CFG_NAND_LEGACY
#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
#define NAND_MAX_CHIPS 1
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define NAND_BIG_DELAY_US 25
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define SECTORSIZE 512
#define ADDR_COLUMN 1
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */

57
include/configs/PLU405.h
View File

@ -81,7 +81,6 @@
#define CONFIG_SUPPORT_VFAT
#define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */
#define CONFIG_AUTO_UPDATE_SHOW 1 /* use board show routine */
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
@ -156,36 +155,15 @@
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
#define CFG_NAND_LEGACY
#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
#define NAND_MAX_CHIPS 1
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define NAND_BIG_DELAY_US 25
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define SECTORSIZE 512
#define ADDR_COLUMN 1
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
@ -264,11 +242,6 @@
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#if 0 /* test-only */
#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
#endif
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
@ -294,9 +267,6 @@
#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
/* total size of a CAT24WC16 is 2048 bytes */
#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
#define CFG_NVRAM_SIZE 242 /* NVRAM size */
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC16) for environment
*/
@ -305,7 +275,7 @@
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */
#if 1 /* test-only */
/* CAT24WC08/16... */
#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
@ -313,15 +283,6 @@
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
/* last 4 bits of the address */
#else
/* CAT24WC32/64... */
#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */
/* 32 byte page write mode using*/
/* last 5 bits of the address */
#endif
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE

37
include/configs/VOH405.h
View File

@ -141,36 +141,15 @@
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
#define CFG_NAND_LEGACY
#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
#define NAND_MAX_CHIPS 1
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define NAND_BIG_DELAY_US 25
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define SECTORSIZE 512
#define ADDR_COLUMN 1
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */

38
include/configs/WUH405.h
View File

@ -133,38 +133,16 @@
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
#define CFG_NAND_LEGACY
#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
#define NAND_MAX_CHIPS 1
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define NAND_BIG_DELAY_US 25
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define SECTORSIZE 512
#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define ADDR_COLUMN 1
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
#define CONFIG_MTD_NAND_VERIFY_WRITE 1 /* verify all writes!!! */
#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
/*-----------------------------------------------------------------------