diff --git a/board/mpc7448hpc2/mpc7448hpc2.c b/board/mpc7448hpc2/mpc7448hpc2.c index d4a047c1d..63c99de17 100644 --- a/board/mpc7448hpc2/mpc7448hpc2.c +++ b/board/mpc7448hpc2/mpc7448hpc2.c @@ -47,7 +47,7 @@ int display_mem_map (void); void after_reloc (ulong dest_addr) { DECLARE_GLOBAL_DATA_PTR; - + /* * Jump to the main U-Boot board init code */ diff --git a/board/mpc7448hpc2/tsi108_init.c b/board/mpc7448hpc2/tsi108_init.c index e3b09cfad..8a7efef77 100644 --- a/board/mpc7448hpc2/tsi108_init.c +++ b/board/mpc7448hpc2/tsi108_init.c @@ -179,7 +179,7 @@ int board_early_init_r (void) ulong temp, i; ulong reg_val; volatile ulong *reg_ptr; - + reg_ptr = (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x900); @@ -300,7 +300,7 @@ int board_early_init_r (void) out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL1, 0x7C0F2000); __asm__ __volatile__ ("sync"); - + /* * Set new value for PB_OCN_BAR1: switch from BOOT to LUT mode. * value for PB_OCN_BAR1: (BA-0xE000_0000 + size 512MB + ENable) @@ -312,7 +312,7 @@ int board_early_init_r (void) /* Make sure that OCN_BAR2 decoder is set (to allow following * immediate read from SDRAM) */ - + temp = in32(CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1); __asm__ __volatile__ ("sync"); @@ -327,11 +327,11 @@ int board_early_init_r (void) * and enable all HLP banks and not just HLP 0 as is being done for * Taiga Rev. 2. */ - + env_init (); #ifndef DISABLE_PBM - + /* * For IBM processors we have to set Address-Only commands generated * by PBM that are different from ones set after reset. @@ -475,10 +475,10 @@ int board_early_init_r (void) for (i = 0; i < 32; i++) { *reg_ptr++ = reg_val; /* P2O_BAR3_LUTx */ - + /* P2O_BAR3_LUT_UPPERx : Set data swapping mode for PBM (byte swapping) */ - *reg_ptr++ = 0; - + *reg_ptr++ = 0; + /* offset = 16MB, address translation is enabled to allow byte swapping */ reg_val += 0x01000000; } @@ -507,7 +507,7 @@ int board_early_init_r (void) #endif /* !DISABLE_PBM */ -#ifdef ENABLE_PCI_CSR_BAR +#ifdef ENABLE_PCI_CSR_BAR /* open if required access to Tsi108 CSRs from the PCI/X bus */ /* enable BAR0 on the PCI/X bus */ reg_val = in32(CFG_TSI108_CSR_BASE + @@ -528,7 +528,7 @@ int board_early_init_r (void) /* * Finally enable PCI/X Bus Master and Memory Space access */ - + reg_val = in32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR); reg_val |= 0x06; out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR, reg_val); @@ -555,7 +555,7 @@ int board_early_init_r (void) * Ensure that Machine Check exception is enabled * We need it to support PCI Bus probing (configuration reads) */ - + reg_val = mfmsr (); mtmsr(reg_val | MSR_ME); @@ -631,7 +631,7 @@ int misc_init_r (void) * thing done with regards to enabling diabling the cache. * So this seems like a good place to print all this information */ - + printf ("CACHE: "); switch (get_cpu_type()) { case CPU_7447A: diff --git a/cpu/74xx_7xx/cpu.c b/cpu/74xx_7xx/cpu.c index 84d5da311..9c8998b60 100644 --- a/cpu/74xx_7xx/cpu.c +++ b/cpu/74xx_7xx/cpu.c @@ -308,9 +308,9 @@ ft_cpu_setup (void *blob, bd_t *bd) u32 *p; ulong clock; int len; - + clock = bd->bi_busfreq; - + p = ft_get_prop (blob, "/cpus/" OF_CPU "/bus-frequency", &len); if (p != NULL) *p = cpu_to_be32 (clock); diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c index 35b23152f..da50985c4 100644 --- a/cpu/ppc4xx/44x_spd_ddr2.c +++ b/cpu/ppc4xx/44x_spd_ddr2.c @@ -168,8 +168,8 @@ static void program_codt(unsigned long *dimm_populated, static void program_mode(unsigned long *dimm_populated, unsigned char *iic0_dimm_addr, unsigned long num_dimm_banks, - ddr_cas_id_t *selected_cas, - int *write_recovery); + ddr_cas_id_t *selected_cas, + int *write_recovery); static void program_tr(unsigned long *dimm_populated, unsigned char *iic0_dimm_addr, unsigned long num_dimm_banks); @@ -185,7 +185,7 @@ static void program_copt1(unsigned long *dimm_populated, static void program_initplr(unsigned long *dimm_populated, unsigned char *iic0_dimm_addr, unsigned long num_dimm_banks, - ddr_cas_id_t selected_cas, + ddr_cas_id_t selected_cas, int write_recovery); static unsigned long is_ecc_enabled(void); static void program_ecc(unsigned long *dimm_populated, @@ -1110,7 +1110,7 @@ static void program_codt(unsigned long *dimm_populated, modt3 = 0x00000000; } } - } else { + } else { codt |= SDRAM_CODT_DQS_2_5_V_DDR1; modt0 = 0x00000000; modt1 = 0x00000000; @@ -1149,7 +1149,7 @@ static void program_codt(unsigned long *dimm_populated, static void program_initplr(unsigned long *dimm_populated, unsigned char *iic0_dimm_addr, unsigned long num_dimm_banks, - ddr_cas_id_t selected_cas, + ddr_cas_id_t selected_cas, int write_recovery) { u32 cas = 0; diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S index 24b30dfe7..3fa52bd75 100644 --- a/cpu/ppc4xx/start.S +++ b/cpu/ppc4xx/start.S @@ -1858,11 +1858,11 @@ pll_wait: #endif /* CONFIG_405EP */ #if defined(CONFIG_440) -#define function_prolog(func_name) .text; \ +#define function_prolog(func_name) .text; \ .align 2; \ .globl func_name; \ func_name: -#define function_epilog(func_name) .type func_name,@function; \ +#define function_epilog(func_name) .type func_name,@function; \ .size func_name,.-func_name /*----------------------------------------------------------------------------+ @@ -1916,43 +1916,43 @@ pll_wait: /*----------------------------------------------------------------------------+ | dcbz_area. +----------------------------------------------------------------------------*/ - function_prolog(dcbz_area) - rlwinm. r5,r4,0,27,31 - rlwinm r5,r4,27,5,31 - beq ..d_ra2 - addi r5,r5,0x0001 -..d_ra2:mtctr r5 -..d_ag2:dcbz r0,r3 - addi r3,r3,32 - bdnz ..d_ag2 - sync - blr - function_epilog(dcbz_area) + function_prolog(dcbz_area) + rlwinm. r5,r4,0,27,31 + rlwinm r5,r4,27,5,31 + beq ..d_ra2 + addi r5,r5,0x0001 +..d_ra2:mtctr r5 +..d_ag2:dcbz r0,r3 + addi r3,r3,32 + bdnz ..d_ag2 + sync + blr + function_epilog(dcbz_area) /*----------------------------------------------------------------------------+ | dflush. Assume 32K at vector address is cachable. +----------------------------------------------------------------------------*/ - function_prolog(dflush) - mfmsr r9 - rlwinm r8,r9,0,15,13 - rlwinm r8,r8,0,17,15 - mtmsr r8 - addi r3,r0,0x0000 - mtspr dvlim,r3 - mfspr r3,ivpr - addi r4,r0,1024 - mtctr r4 + function_prolog(dflush) + mfmsr r9 + rlwinm r8,r9,0,15,13 + rlwinm r8,r8,0,17,15 + mtmsr r8 + addi r3,r0,0x0000 + mtspr dvlim,r3 + mfspr r3,ivpr + addi r4,r0,1024 + mtctr r4 ..dflush_loop: - lwz r6,0x0(r3) - addi r3,r3,32 - bdnz ..dflush_loop - addi r3,r3,-32 - mtctr r4 -..ag: dcbf r0,r3 - addi r3,r3,-32 - bdnz ..ag - sync - mtmsr r9 - blr - function_epilog(dflush) + lwz r6,0x0(r3) + addi r3,r3,32 + bdnz ..dflush_loop + addi r3,r3,-32 + mtctr r4 +..ag: dcbf r0,r3 + addi r3,r3,-32 + bdnz ..ag + sync + mtmsr r9 + blr + function_epilog(dflush) #endif /* CONFIG_440 */ diff --git a/doc/README.mpc7448hpc2 b/doc/README.mpc7448hpc2 index 0e40e3926..8659e8367 100644 --- a/doc/README.mpc7448hpc2 +++ b/doc/README.mpc7448hpc2 @@ -92,7 +92,7 @@ SW2[1-6]: CPU core frequency CPU Core Frequency (MHz) Bus Frequency 123456 100 133 167 200 Ratio - + ------ SW2=101100 500 667 833 1000 5x SW2=100100 550 733 917 1100 5.5x @@ -109,43 +109,43 @@ hardware specifications for more information. SW2[7-8]: Bus Protocol and CPU Reset Option - 7 + 7 - SW2=0 System bus uses MPX bus protocol SW2=1 System bus uses 60x bus protocol - 8 + 8 - SW2=0 TSI108 can cause CPU reset SW2=1 TSI108 can not cause CPU reset SW3[1-8] system options - 123 + 123 --- SW3=xxx Connected to GPIO[0:2] on TSI108 - 4 + 4 - SW3=0 CPU boots from low half of flash SW3=1 CPU boots from high half of flash - 5 + 5 - SW3=0 SATA and slot2 connected to PCI bus SW3=1 Only slot1 connected to PCI bus - 6 + 6 - SW3=0 USB connected to PCI bus SW3=1 USB disconnected from PCI bus - 7 + 7 - SW3=0 Flash is write protected SW3=1 Flash is NOT write protected - 8 + 8 - SW3=0 CPU will boot from flash SW3=1 CPU will boot from PromJet @@ -166,20 +166,19 @@ SW4[4-6]: DDR2 SDRAM frequency Bus Frequency (MHz) --- SW4=000 external clock - SW4=011 system clock + SW4=011 system clock SW4=100 133 SW4=101 166 SW4=110 200 others reserved SW4[7-8]: PCI/PCI-X frequency control - 7 + 7 - SW4=0 PCI/PCI-X bus operates normally SW4=1 PCI bus forced to PCI-33 mode - 8 + 8 - SW4=0 PCI-X mode at 133 MHz allowed SW4=1 PCI-X mode limited to 100 MHz - diff --git a/drivers/tsi108_i2c.c b/drivers/tsi108_i2c.c index c100cb824..eb52cb66c 100644 --- a/drivers/tsi108_i2c.c +++ b/drivers/tsi108_i2c.c @@ -82,15 +82,10 @@ static int i2c_read_byte ( /* Wait until operation completed */ do { /* Read I2C operation status */ - temp = - *(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + - I2C_CNTRL2); + temp = *(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + I2C_CNTRL2); - if (0 == - (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_START))) - { - if (0 == - (temp & + if (0 == (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_START))) { + if (0 == (temp & (I2C_CNTRL2_I2C_CFGERR | I2C_CNTRL2_I2C_TO_ERR)) ) { @@ -152,9 +147,7 @@ int i2c_read (uchar chip_addr, uint byte_addr, int alen, /* Check for valid I2C address */ if (chip_addr <= 0x7F && (byte_addr + len) <= (0x01 << (alen * 8))) { while (len--) { - op_status = - i2c_read_byte(i2c_if, chip_addr, byte_addr++, - buffer++); + op_status = i2c_read_byte(i2c_if, chip_addr, byte_addr++, buffer++); if (TSI108_I2C_SUCCESS != op_status) { DPRINT (("I2C read_byte() failed: 0x%02x (%d left)\n", op_status, len)); @@ -182,10 +175,7 @@ static int i2c_write_byte (uchar chip_addr,/* I2C device address on the bus */ /* Check if I2C operation is in progress */ temp = *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + I2C_CNTRL2); - if (0 == - (temp & - (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_WR_STATUS | I2C_CNTRL2_START))) - { + if (0 == (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_WR_STATUS | I2C_CNTRL2_START))) { /* Place data into the I2C Tx Register */ *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + I2C_TX_DATA) = (u32) * buffer; @@ -200,7 +190,7 @@ static int i2c_write_byte (uchar chip_addr,/* I2C device address on the bus */ /* Issue the write command (at this moment all other parameters * are 0 (size = 1 byte, lane = 0) */ - + *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + I2C_CNTRL2) = (I2C_CNTRL2_START); @@ -209,15 +199,10 @@ static int i2c_write_byte (uchar chip_addr,/* I2C device address on the bus */ /* Wait until operation completed */ do { /* Read I2C operation status */ - temp = - *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + - I2C_CNTRL2); + temp = *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + I2C_CNTRL2); - if (0 == - (temp & (I2C_CNTRL2_WR_STATUS | I2C_CNTRL2_START))) - { - if (0 == - (temp & + if (0 == (temp & (I2C_CNTRL2_WR_STATUS | I2C_CNTRL2_START))) { + if (0 == (temp & (I2C_CNTRL2_I2C_CFGERR | I2C_CNTRL2_I2C_TO_ERR))) { op_status = TSI108_I2C_SUCCESS; diff --git a/include/configs/mpc7448hpc2.h b/include/configs/mpc7448hpc2.h index eb528dfaf..243a3f6c8 100644 --- a/include/configs/mpc7448hpc2.h +++ b/include/configs/mpc7448hpc2.h @@ -285,7 +285,7 @@ /* PCI view of System Memory */ #define CFG_PCI_MEMORY_BUS 0x00000000 #define CFG_PCI_MEMORY_PHYS 0x00000000 -#define CFG_PCI_MEMORY_SIZE 0x80000000 +#define CFG_PCI_MEMORY_SIZE 0x80000000 /* PCI Memory Space */ #define CFG_PCI_MEM_BUS (CFG_PCI_MEM_PHYS)