From 566a494f592ae3b3c0785d90d4e1ba45574880c4 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Fri, 22 Jun 2007 19:11:54 +0200 Subject: [PATCH] [PCS440EP] upgrade the PCS440EP board: - Show on the Status LEDs, some States of the board. - Get the MAC addresses from the EEProm - use PREBOOT - use the CF on the board. - check the U-Boot image in the Flash with a SHA1 checksum. - use dynamic TLB entries generation for the SDRAM Signed-off-by: Heiko Schocher --- Makefile | 9 +- README | 79 +++-- board/hermes/hermes.c | 1 + board/logodl/logodl.c | 1 + board/pcs440ep/config.mk | 3 + board/pcs440ep/flash.c | 4 + board/pcs440ep/init.S | 41 +-- board/pcs440ep/pcs440ep.c | 500 +++++++++++++++++++++++++++++++- board/pcs440ep/u-boot.lds | 1 + board/sc520_cdp/sc520_cdp.c | 1 + board/sc520_spunk/sc520_spunk.c | 1 + common/cmd_doc.c | 19 +- common/cmd_ide.c | 60 +++- common/cmd_nand.c | 38 ++- common/cmd_net.c | 26 +- common/cmd_reiser.c | 6 +- common/env_common.c | 2 +- cpu/ppc4xx/44x_spd_ddr.c | 26 +- cpu/ppc4xx/44x_spd_ddr2.c | 71 +++-- disk/part.c | 3 +- fs/fat/fat.c | 42 +-- include/configs/pcs440ep.h | 83 +++++- include/sha1.h | 115 ++++++++ include/status_led.h | 7 + lib_generic/Makefile | 2 +- lib_generic/sha1.c | 430 +++++++++++++++++++++++++++ lib_ppc/board.c | 5 +- net/eth.c | 11 + tools/Makefile | 23 +- tools/ubsha1.c | 119 ++++++++ 30 files changed, 1572 insertions(+), 157 deletions(-) create mode 100644 include/sha1.h create mode 100644 lib_generic/sha1.c create mode 100644 tools/ubsha1.c diff --git a/Makefile b/Makefile index d5e220aad..3d64d1673 100644 --- a/Makefile +++ b/Makefile @@ -245,7 +245,7 @@ __LIBS := $(subst $(obj),,$(LIBS)) ######################################################################### ######################################################################### -ALL = $(obj)u-boot.srec $(obj)u-boot.bin $(obj)System.map $(U_BOOT_NAND) +ALL += $(obj)u-boot.srec $(obj)u-boot.bin $(obj)System.map $(U_BOOT_NAND) all: $(ALL) @@ -265,6 +265,9 @@ $(obj)u-boot.img: $(obj)u-boot.bin sed -e 's/"[ ]*$$/ for $(BOARD) board"/') \ -d $< $@ +$(obj)u-boot.sha1: $(obj)u-boot.bin + ./tools/ubsha1 $(obj)u-boot.bin + $(obj)u-boot.dis: $(obj)u-boot $(OBJDUMP) -d $< > $@ @@ -2455,7 +2458,7 @@ clean: $(obj)examples/smc91111_eeprom $(obj)examples/interrupt \ $(obj)examples/test_burst rm -f $(obj)tools/img2srec $(obj)tools/mkimage $(obj)tools/envcrc \ - $(obj)tools/gen_eth_addr + $(obj)tools/gen_eth_addr $(obj)tools/ubsha1 rm -f $(obj)tools/mpc86x_clk $(obj)tools/ncb rm -f $(obj)tools/easylogo/easylogo $(obj)tools/bmp_logo rm -f $(obj)tools/gdb/astest $(obj)tools/gdb/gdbcont $(obj)tools/gdb/gdbsend @@ -2478,7 +2481,7 @@ clobber: clean rm -f $(OBJS) $(obj)*.bak $(obj)ctags $(obj)etags $(obj)TAGS $(obj)include/version_autogenerated.h rm -fr $(obj)*.*~ rm -f $(obj)u-boot $(obj)u-boot.map $(obj)u-boot.hex $(ALL) - rm -f $(obj)tools/crc32.c $(obj)tools/environment.c $(obj)tools/env/crc32.c + rm -f $(obj)tools/crc32.c $(obj)tools/environment.c $(obj)tools/env/crc32.c $(obj)tools/sha1.c rm -f $(obj)tools/inca-swap-bytes $(obj)cpu/mpc824x/bedbug_603e.c rm -f $(obj)include/asm/proc $(obj)include/asm/arch $(obj)include/asm [ ! -d $(OBJTREE)/nand_spl ] || find $(obj)nand_spl -lname "*" -print | xargs rm -f diff --git a/README b/README index bb5b46e33..b64bfb247 100644 --- a/README +++ b/README @@ -1699,28 +1699,69 @@ The following options need to be configured: -31 post/post.c POST test failed, detected by post_output_backlog() -32 post/post.c POST test failed, detected by post_run_single() - -1 common/cmd_doc.c Bad usage of "doc" command - -1 common/cmd_doc.c No boot device - -1 common/cmd_doc.c Unknown Chip ID on boot device - -1 common/cmd_doc.c Read Error on boot device - -1 common/cmd_doc.c Image header has bad magic number + 34 common/cmd_doc.c before loading a Image from a DOC device + -35 common/cmd_doc.c Bad usage of "doc" command + 35 common/cmd_doc.c correct usage of "doc" command + -36 common/cmd_doc.c No boot device + 36 common/cmd_doc.c correct boot device + -37 common/cmd_doc.c Unknown Chip ID on boot device + 37 common/cmd_doc.c correct chip ID found, device available + -38 common/cmd_doc.c Read Error on boot device + 38 common/cmd_doc.c reading Image header from DOC device OK + -39 common/cmd_doc.c Image header has bad magic number + 39 common/cmd_doc.c Image header has correct magic number + -40 common/cmd_doc.c Error reading Image from DOC device + 40 common/cmd_doc.c Image header has correct magic number + 41 common/cmd_ide.c before loading a Image from a IDE device + -42 common/cmd_ide.c Bad usage of "ide" command + 42 common/cmd_ide.c correct usage of "ide" command + -43 common/cmd_ide.c No boot device + 43 common/cmd_ide.c boot device found + -44 common/cmd_ide.c Device not available + 44 common/cmd_ide.c Device available + -45 common/cmd_ide.c wrong partition selected + 45 common/cmd_ide.c partition selected + -46 common/cmd_ide.c Unknown partition table + 46 common/cmd_ide.c valid partition table found + -47 common/cmd_ide.c Invalid partition type + 47 common/cmd_ide.c correct partition type + -48 common/cmd_ide.c Error reading Image Header on boot device + 48 common/cmd_ide.c reading Image Header from IDE device OK + -49 common/cmd_ide.c Image header has bad magic number + 49 common/cmd_ide.c Image header has correct magic number + -50 common/cmd_ide.c Image header has bad checksum + 50 common/cmd_ide.c Image header has correct checksum + -51 common/cmd_ide.c Error reading Image from IDE device + 51 common/cmd_ide.c reading Image from IDE device OK + 52 common/cmd_nand.c before loading a Image from a NAND device + -53 common/cmd_nand.c Bad usage of "nand" command + 53 common/cmd_nand.c correct usage of "nand" command + -54 common/cmd_nand.c No boot device + 54 common/cmd_nand.c boot device found + -55 common/cmd_nand.c Unknown Chip ID on boot device + 55 common/cmd_nand.c correct chip ID found, device available + -56 common/cmd_nand.c Error reading Image Header on boot device + 56 common/cmd_nand.c reading Image Header from NAND device OK + -57 common/cmd_nand.c Image header has bad magic number + 57 common/cmd_nand.c Image header has correct magic number + -58 common/cmd_nand.c Error reading Image from NAND device + 58 common/cmd_nand.c reading Image from NAND device OK - -1 common/cmd_ide.c Bad usage of "ide" command - -1 common/cmd_ide.c No boot device - -1 common/cmd_ide.c Unknown boot device - -1 common/cmd_ide.c Unknown partition table - -1 common/cmd_ide.c Invalid partition type - -1 common/cmd_ide.c Read Error on boot device - -1 common/cmd_ide.c Image header has bad magic number + -60 common/env_common.c Environment has a bad CRC, using default - -1 common/cmd_nand.c Bad usage of "nand" command - -1 common/cmd_nand.c No boot device - -1 common/cmd_nand.c Unknown Chip ID on boot device - -1 common/cmd_nand.c Read Error on boot device - -1 common/cmd_nand.c Image header has bad magic number - - -1 common/env_common.c Environment has a bad CRC, using default + 64 net/eth.c starting with Ethernetconfiguration. + -64 net/eth.c no Ethernet found. + 65 net/eth.c Ethernet found. + -80 common/cmd_net.c usage wrong + 80 common/cmd_net.c before calling NetLoop() + -81 common/cmd_net.c some error in NetLoop() occured + 81 common/cmd_net.c NetLoop() back without error + -82 common/cmd_net.c size == 0 (File with size 0 loaded) + 82 common/cmd_net.c trying automatic boot + 83 common/cmd_net.c running autoscript + -83 common/cmd_net.c some error in automatic boot or autoscript + 84 common/cmd_net.c end without errors Modem Support: -------------- diff --git a/board/hermes/hermes.c b/board/hermes/hermes.c index a523db1a4..8fd081fef 100644 --- a/board/hermes/hermes.c +++ b/board/hermes/hermes.c @@ -597,6 +597,7 @@ void show_boot_progress (int status) { volatile immap_t *immr = (immap_t *) CFG_IMMR; + if (status < -32) status = -1; /* let things compatible */ status ^= 0x0F; status = (status & 0x0F) << 14; immr->im_cpm.cp_pbdat = (immr->im_cpm.cp_pbdat & ~PB_LED_ALL) | status; diff --git a/board/logodl/logodl.c b/board/logodl/logodl.c index 14fd28f56..897787bcf 100644 --- a/board/logodl/logodl.c +++ b/board/logodl/logodl.c @@ -107,6 +107,7 @@ void logodl_set_led(int led, int state) void show_boot_progress (int status) { + if (status < -32) status = -1; /* let things compatible */ /* switch(status) { case 1: logodl_set_led(0,1); break; diff --git a/board/pcs440ep/config.mk b/board/pcs440ep/config.mk index 319c4fa21..4d942ebc7 100644 --- a/board/pcs440ep/config.mk +++ b/board/pcs440ep/config.mk @@ -25,6 +25,9 @@ # PCS440EP board # +# Check the U-Boot Image with a SHA1 checksum +ALL += $(obj)u-boot.sha1 + #TEXT_BASE = 0x00001000 ifeq ($(ramsym),1) diff --git a/board/pcs440ep/flash.c b/board/pcs440ep/flash.c index ece54781b..70014407c 100644 --- a/board/pcs440ep/flash.c +++ b/board/pcs440ep/flash.c @@ -83,6 +83,7 @@ void flash_print_info(flash_info_t *info) case FLASH_MAN_FUJ: printf ("FUJITSU "); break; case FLASH_MAN_SST: printf ("SST "); break; case FLASH_MAN_EXCEL: printf ("Excel Semiconductor "); break; + case FLASH_MAN_MX: printf ("MXIC "); break; default: printf ("Unknown Vendor "); break; } @@ -195,6 +196,9 @@ static ulong flash_get_size(vu_long *addr, flash_info_t *info) case (CFG_FLASH_WORD_SIZE)EXCEL_MANUFACT: info->flash_id = FLASH_MAN_EXCEL; break; + case (CFG_FLASH_WORD_SIZE)MX_MANUFACT: + info->flash_id = FLASH_MAN_MX; + break; default: info->flash_id = FLASH_UNKNOWN; info->sector_count = 0; diff --git a/board/pcs440ep/init.S b/board/pcs440ep/init.S index 0eee4d809..36a40c97a 100644 --- a/board/pcs440ep/init.S +++ b/board/pcs440ep/init.S @@ -87,27 +87,32 @@ .globl tlbtab tlbtab: - tlbtab_start + tlbtab_start - /* - * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the - * speed up boot process. It is patched after relocation to enable SA_I - */ - tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/) + /* + * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the + * speed up boot process. It is patched after relocation to enable SA_I + */ + tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/) - /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ - tlbentry( CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G ) + /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ + tlbentry( CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G ) - tlbentry( CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I ) - tlbentry( CFG_PCI_BASE, SZ_256M, CFG_PCI_BASE, 0, AC_R|AC_W|SA_G|SA_I ) + /* + * TLB entries for SDRAM are not needed on this platform. + * They are dynamically generated in the SPD DDR detection + * routine. + */ - /* PCI */ - tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 0, AC_R|AC_W|SA_G|SA_I ) - tlbentry( CFG_PCI_MEMBASE1, SZ_256M, CFG_PCI_MEMBASE1, 0, AC_R|AC_W|SA_G|SA_I ) - tlbentry( CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 0, AC_R|AC_W|SA_G|SA_I ) - tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 0, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_PCI_BASE, SZ_256M, CFG_PCI_BASE, 0, AC_R|AC_W|SA_G|SA_I ) - /* USB 2.0 Device */ - tlbentry( CFG_USB_DEVICE, SZ_1K, 0x50000000, 0, AC_R|AC_W|SA_G|SA_I ) + /* PCI */ + tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 0, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_PCI_MEMBASE1, SZ_256M, CFG_PCI_MEMBASE1, 0, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 0, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 0, AC_R|AC_W|SA_G|SA_I ) - tlbtab_end + /* USB 2.0 Device */ + tlbentry( CFG_USB_DEVICE, SZ_1K, 0x50000000, 0, AC_R|AC_W|SA_G|SA_I ) + + tlbtab_end diff --git a/board/pcs440ep/pcs440ep.c b/board/pcs440ep/pcs440ep.c index 8858f0a5e..f638589df 100644 --- a/board/pcs440ep/pcs440ep.c +++ b/board/pcs440ep/pcs440ep.c @@ -23,20 +23,112 @@ #include #include +#include +#include +#include #include #include +#include +#include DECLARE_GLOBAL_DATA_PTR; extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ -static void set_leds(int val) +unsigned char sha1_checksum[SHA1_SUM_LEN]; + +/* swap 4 Bits (Bit0 = Bit3, Bit1 = Bit2, Bit2 = Bit1 and Bit3 = Bit0) */ +unsigned char swapbits[16] = {0x0, 0x8, 0x4, 0xc, 0x2, 0xa, 0x6, 0xe, + 0x1, 0x9, 0x5, 0xd, 0x3, 0xb, 0x7, 0xf}; + +static void set_leds (int val) { - unsigned char led[16] = {0x0, 0x8, 0x4, 0xc, 0x2, 0xa, 0x6, 0xe, - 0x1, 0x9, 0x5, 0xd, 0x3, 0xb, 0x7, 0xf}; - out32(GPIO0_OR, (in32(GPIO0_OR) & ~0x78000000) | (led[val] << 27)); + out32(GPIO0_OR, (in32 (GPIO0_OR) & ~0x78000000) | (val << 27)); } +#define GET_LEDS ((in32 (GPIO0_OR) & 0x78000000) >> 27) + +void __led_init (led_id_t mask, int state) +{ + int val = GET_LEDS; + + if (state == STATUS_LED_ON) + val |= mask; + else + val &= ~mask; + set_leds (val); +} + +void __led_set (led_id_t mask, int state) +{ + int val = GET_LEDS; + + if (state == STATUS_LED_ON) + val |= mask; + else if (state == STATUS_LED_OFF) + val &= ~mask; + set_leds (val); +} + +void __led_toggle (led_id_t mask) +{ + int val = GET_LEDS; + + val ^= mask; + set_leds (val); +} + +static void status_led_blink (void) +{ + int i; + int val = GET_LEDS; + + /* set all LED which are on, to state BLINKING */ + for (i = 0; i < 4; i++) { + if (val & 0x08) status_led_set (i, STATUS_LED_BLINKING); + val = val << 1; + } +} + +#if defined(CONFIG_SHOW_BOOT_PROGRESS) +void show_boot_progress (int val) +{ + /* find all valid Codes for val in README */ + if (val == -30) return; + if (val < 0) { + /* smthing goes wrong */ + status_led_blink (); + return; + } + switch (val) { + case 1: + /* validating Image */ + status_led_set (0, STATUS_LED_OFF); + status_led_set (1, STATUS_LED_ON); + status_led_set (2, STATUS_LED_ON); + break; + case 15: + /* booting */ + status_led_set (0, STATUS_LED_ON); + status_led_set (1, STATUS_LED_ON); + status_led_set (2, STATUS_LED_ON); + break; + case 64: + /* starting Ethernet configuration */ + status_led_set (0, STATUS_LED_OFF); + status_led_set (1, STATUS_LED_OFF); + status_led_set (2, STATUS_LED_ON); + break; + case 80: + /* loading Image */ + status_led_set (0, STATUS_LED_ON); + status_led_set (1, STATUS_LED_OFF); + status_led_set (2, STATUS_LED_ON); + break; + } +} +#endif + int board_early_init_f(void) { register uint reg; @@ -85,6 +177,252 @@ int board_early_init_f(void) return 0; } +#define EEPROM_LEN 256 +void load_sernum_ethaddr (void) +{ + int ret; + char buf[EEPROM_LEN]; + char mac[32]; + char *use_eeprom; + u16 checksumcrc16 = 0; + + /* read the MACs from EEprom */ + status_led_set (0, STATUS_LED_ON); + status_led_set (1, STATUS_LED_ON); + ret = eeprom_read (CFG_I2C_EEPROM_ADDR, 0, (uchar *)buf, EEPROM_LEN); + if (ret == 0) { + checksumcrc16 = cyg_crc16 ((uchar *)buf, EEPROM_LEN - 2); + /* check, if the EEprom is programmed: + * - The Prefix(Byte 0,1,2) is equal to "ATR" + * - The checksum, stored in the last 2 Bytes, is correct + */ + if ((strncmp (buf,"ATR",3) != 0) || + ((checksumcrc16 >> 8) != buf[EEPROM_LEN - 2]) || + ((checksumcrc16 & 0xff) != buf[EEPROM_LEN - 1])) + { + /* EEprom is not programmed */ + printf("%s: EEPROM Checksum not OK\n", __FUNCTION__); + } else { + /* get the MACs */ + sprintf (mac, "%02x:%02x:%02x:%02x:%02x:%02x", + buf[3], + buf[4], + buf[5], + buf[6], + buf[7], + buf[8]); + setenv ("ethaddr", (char *) mac); + sprintf (mac, "%02x:%02x:%02x:%02x:%02x:%02x", + buf[9], + buf[10], + buf[11], + buf[12], + buf[13], + buf[14]); + setenv ("eth1addr", (char *) mac); + return; + } + } + + /* some error reading the EEprom */ + if ((use_eeprom = getenv ("use_eeprom_ethaddr")) == NULL) { + /* dont use bootcmd */ + setenv("bootdelay", "-1"); + return; + } + /* == default ? use standard */ + if (strncmp (use_eeprom, "default", 7) == 0) { + return; + } + /* Env doesnt exist -> hang */ + status_led_blink (); + hang (); + return; +} + +#ifdef CONFIG_PREBOOT + +static uchar kbd_magic_prefix[] = "key_magic"; +static uchar kbd_command_prefix[] = "key_cmd"; + +struct kbd_data_t { + char s1; + char s2; +}; + +struct kbd_data_t* get_keys (struct kbd_data_t *kbd_data) +{ + char *val; + unsigned long tmp; + + /* use the DIPs for some bootoptions */ + val = getenv (ENV_NAME_DIP); + tmp = simple_strtoul (val, NULL, 16); + + kbd_data->s2 = (tmp & 0x0f); + kbd_data->s1 = (tmp & 0xf0) >> 4; + return kbd_data; +} + +static int compare_magic (const struct kbd_data_t *kbd_data, char *str) +{ + char s1 = str[0]; + + if (s1 >= '0' && s1 <= '9') + s1 -= '0'; + else if (s1 >= 'a' && s1 <= 'f') + s1 = s1 - 'a' + 10; + else if (s1 >= 'A' && s1 <= 'F') + s1 = s1 - 'A' + 10; + else + return -1; + + if (s1 != kbd_data->s1) return -1; + + s1 = str[1]; + if (s1 >= '0' && s1 <= '9') + s1 -= '0'; + else if (s1 >= 'a' && s1 <= 'f') + s1 = s1 - 'a' + 10; + else if (s1 >= 'A' && s1 <= 'F') + s1 = s1 - 'A' + 10; + else + return -1; + + if (s1 != kbd_data->s2) return -1; + return 0; +} + +static char *key_match (const struct kbd_data_t *kbd_data) +{ + char magic[sizeof (kbd_magic_prefix) + 1]; + char *suffix; + char *kbd_magic_keys; + + /* + * The following string defines the characters that can be appended + * to "key_magic" to form the names of environment variables that + * hold "magic" key codes, i. e. such key codes that can cause + * pre-boot actions. If the string is empty (""), then only + * "key_magic" is checked (old behaviour); the string "125" causes + * checks for "key_magic1", "key_magic2" and "key_magic5", etc. + */ + if ((kbd_magic_keys = getenv ("magic_keys")) == NULL) + kbd_magic_keys = ""; + + /* loop over all magic keys; + * use '\0' suffix in case of empty string + */ + for (suffix = kbd_magic_keys; *suffix || + suffix == kbd_magic_keys; ++suffix) { + sprintf (magic, "%s%c", kbd_magic_prefix, *suffix); + if (compare_magic (kbd_data, getenv (magic)) == 0) { + char cmd_name[sizeof (kbd_command_prefix) + 1]; + char *cmd; + + sprintf (cmd_name, "%s%c", kbd_command_prefix, *suffix); + cmd = getenv (cmd_name); + + return (cmd); + } + } + return (NULL); +} + +#endif /* CONFIG_PREBOOT */ + +static int pcs440ep_readinputs (void) +{ + int i; + char value[20]; + + /* read the inputs and set the Envvars */ + /* Revision Level Bit 26 - 29 */ + i = ((in32 (GPIO0_IR) & 0x0000003c) >> 2); + i = swapbits[i]; + sprintf (value, "%02x", i); + setenv (ENV_NAME_REVLEV, value); + /* Solder Switch Bit 30 - 33 */ + i = (in32 (GPIO0_IR) & 0x00000003) << 2; + i += (in32 (GPIO1_IR) & 0xc0000000) >> 30; + i = swapbits[i]; + sprintf (value, "%02x", i); + setenv (ENV_NAME_SOLDER, value); + /* DIP Switch Bit 49 - 56 */ + i = ((in32 (GPIO1_IR) & 0x00007f80) >> 7); + i = (swapbits[i & 0x0f] << 4) + swapbits[(i & 0xf0) >> 4]; + sprintf (value, "%02x", i); + setenv (ENV_NAME_DIP, value); + return 0; +} + + +#if defined(CONFIG_SHA1_CHECK_UB_IMG) +/************************************************************************* + * calculate a SHA1 sum for the U-Boot image in Flash. + * + ************************************************************************/ +static int pcs440ep_sha1 (int docheck) +{ + unsigned char *data; + unsigned char *ptroff; + unsigned char output[20]; + unsigned char org[20]; + int i, len = CONFIG_SHA1_LEN; + + memcpy ((char *)CFG_LOAD_ADDR, (char *)CONFIG_SHA1_START, len); + data = (unsigned char *)CFG_LOAD_ADDR; + ptroff = &data[len + SHA1_SUM_POS]; + + for (i = 0; i < SHA1_SUM_LEN; i++) { + org[i] = ptroff[i]; + ptroff[i] = 0; + } + + sha1_csum ((unsigned char *) data, len, (unsigned char *)output); + + if (docheck == 2) { + for (i = 0; i < 20 ; i++) { + printf("%02X ", output[i]); + } + printf("\n"); + } + if (docheck == 1) { + for (i = 0; i < 20 ; i++) { + if (org[i] != output[i]) return 1; + } + } + return 0; +} + +/************************************************************************* + * do some checks after the SHA1 checksum from the U-Boot Image was + * calculated. + * + ************************************************************************/ +static void pcs440ep_checksha1 (void) +{ + int ret; + char *cs_test; + + ret = pcs440ep_sha1 (1); + if (ret == 0) return; + + if ((cs_test = getenv ("cs_test")) == NULL) { + /* Env doesnt exist -> hang */ + status_led_blink (); + hang (); + } + + if (strncmp (cs_test, "off", 3) == 0) { + printf ("SHA1 U-Boot sum NOT ok!\n"); + setenv ("bootdelay", "-1"); + } +} +#else +static __inline__ void pcs440ep_checksha1 (void) { do {} while (0);} +#endif + int misc_init_r (void) { uint pbcr; @@ -139,6 +477,18 @@ int misc_init_r (void) CFG_ENV_ADDR_REDUND + 2*CFG_ENV_SECT_SIZE - 1, &flash_info[1]); + pcs440ep_readinputs (); + pcs440ep_checksha1 (); +#ifdef CONFIG_PREBOOT + { + struct kbd_data_t kbd_data; + /* Decode keys */ + char *str = strdup (key_match (get_keys (&kbd_data))); + /* Set or delete definition */ + setenv ("preboot", str); + free (str); + } +#endif /* CONFIG_PREBOOT */ return 0; } @@ -156,13 +506,34 @@ int checkboard(void) return (0); } + +#if defined(CONFIG_PPC4xx_USE_SPD_DDR_INIT_HANG) +void spd_ddr_init_hang (void) +{ + status_led_set (0, STATUS_LED_OFF); + status_led_set (1, STATUS_LED_ON); + /* we cannot use hang() because we are still running from + Flash, and so the status_led driver is not initialized */ + puts ("### ERROR ### Please RESET the board ###\n"); + for (;;) { + __led_toggle (4); + udelay (100000); + } +} +#endif + long int initdram (int board_type) { long dram_size = 0; - set_leds(1); /* display boot info counter */ + status_led_set (0, STATUS_LED_ON); + status_led_set (1, STATUS_LED_OFF); dram_size = spd_sdram(); - set_leds(2); /* display boot info counter */ + status_led_set (0, STATUS_LED_OFF); + status_led_set (1, STATUS_LED_ON); + if (dram_size == 0) { + hang(); + } return dram_size; } @@ -377,3 +748,120 @@ void hw_watchdog_reset(void) } #endif + +/************************************************************************* + * "led" Commando for the U-Boot shell + * + ************************************************************************/ +int do_led (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + int rcode = 0; + ulong pattern = 0; + + pattern = simple_strtoul (argv[1], NULL, 10); + if (pattern > 200) { + status_led_blink (); + hang (); + return rcode; + } + if (pattern > 100) { + status_led_blink (); + return rcode; + } + pattern &= 0x0f; + set_leds (pattern); + return rcode; +} + +U_BOOT_CMD( + led, 2, 1, do_led, + "led - set the led\n", + NULL +); + +#if defined(CONFIG_SHA1_CHECK_UB_IMG) +/************************************************************************* + * "sha1" Commando for the U-Boot shell + * + ************************************************************************/ +int do_sha1 (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + int rcode = -1; + + if (argc < 2) { + usage: + printf ("Usage:\n%s\n", cmdtp->usage); + return 1; + } + + if (argc >= 3) { + unsigned char *data; + unsigned char output[20]; + int len; + int i; + + data = (unsigned char *)simple_strtoul (argv[1], NULL, 16); + len = simple_strtoul (argv[2], NULL, 16); + sha1_csum (data, len, (unsigned char *)output); + printf ("U-Boot sum:\n"); + for (i = 0; i < 20 ; i++) { + printf ("%02X ", output[i]); + } + printf ("\n"); + if (argc == 4) { + data = (unsigned char *)simple_strtoul (argv[3], NULL, 16); + memcpy (data, output, 20); + } + return 0; + } + if (argc == 2) { + char *ptr = argv[1]; + if (*ptr != '-') goto usage; + ptr++; + if ((*ptr == 'c') || (*ptr == 'C')) { + rcode = pcs440ep_sha1 (1); + printf ("SHA1 U-Boot sum %sok!\n", (rcode != 0) ? "not " : ""); + } else if ((*ptr == 'p') || (*ptr == 'P')) { + rcode = pcs440ep_sha1 (2); + } else { + rcode = pcs440ep_sha1 (0); + } + return rcode; + } + return rcode; +} + +U_BOOT_CMD( + sha1, 4, 1, do_sha1, + "sha1 - calculate the SHA1 Sum\n", + "address len [addr] calculate the SHA1 sum [save at addr]\n" + " -p calculate the SHA1 sum from the U-Boot image in flash and print\n" + " -c check the U-Boot image in flash\n" +); +#endif + +#ifdef CONFIG_IDE_PREINIT +int ide_preinit (void) +{ + /* Set True IDE Mode */ + out32 (GPIO0_OR, (in32 (GPIO0_OR) | 0x00100000)); + out32 (GPIO0_OR, (in32 (GPIO0_OR) | 0x00200000)); + out32 (GPIO1_OR, (in32 (GPIO1_OR) & ~0x00008040)); + udelay (100000); + return 0; +} +#endif + +#if defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET) +void ide_set_reset (int idereset) +{ + debug ("ide_reset(%d)\n", idereset); + if (idereset == 0) { + out32 (GPIO0_OR, (in32 (GPIO0_OR) | 0x00200000)); + } else { + out32 (GPIO0_OR, (in32 (GPIO0_OR) & ~0x00200000)); + } + udelay (10000); +} +#endif /* defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET) */ + diff --git a/board/pcs440ep/u-boot.lds b/board/pcs440ep/u-boot.lds index 6ab476ab1..6506ccdcf 100644 --- a/board/pcs440ep/u-boot.lds +++ b/board/pcs440ep/u-boot.lds @@ -65,6 +65,7 @@ SECTIONS { cpu/ppc4xx/start.o (.text) board/pcs440ep/init.o (.text) + lib_generic/sha1.o (.text) *(.text) *(.fixup) diff --git a/board/sc520_cdp/sc520_cdp.c b/board/sc520_cdp/sc520_cdp.c index b6add59bb..f6f0e7244 100644 --- a/board/sc520_cdp/sc520_cdp.c +++ b/board/sc520_cdp/sc520_cdp.c @@ -507,6 +507,7 @@ int dram_init(void) void show_boot_progress(int val) { + if (val < -32) val = -1; /* let things compatible */ outb(val&0xff, 0x80); outb((val&0xff00)>>8, 0x680); } diff --git a/board/sc520_spunk/sc520_spunk.c b/board/sc520_spunk/sc520_spunk.c index ed226fd64..d119a7d99 100644 --- a/board/sc520_spunk/sc520_spunk.c +++ b/board/sc520_spunk/sc520_spunk.c @@ -507,6 +507,7 @@ void show_boot_progress(int val) { int version = read_mmcr_byte(SC520_SYSINFO); + if (val < -32) val = -1; /* let things compatible */ if (version == 0) { /* PIO31-PIO16 Data */ write_mmcr_word(SC520_PIODATA31_16, diff --git a/common/cmd_doc.c b/common/cmd_doc.c index ab3751695..4e624a2f3 100644 --- a/common/cmd_doc.c +++ b/common/cmd_doc.c @@ -216,6 +216,7 @@ int do_docboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) image_header_t *hdr; int rcode = 0; + SHOW_BOOT_PROGRESS (34); switch (argc) { case 1: addr = CFG_LOAD_ADDR; @@ -236,24 +237,27 @@ int do_docboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) break; default: printf ("Usage:\n%s\n", cmdtp->usage); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-35); return 1; } + SHOW_BOOT_PROGRESS (35); if (!boot_device) { puts ("\n** No boot device **\n"); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-36); return 1; } + SHOW_BOOT_PROGRESS (36); dev = simple_strtoul(boot_device, &ep, 16); if ((dev >= CFG_MAX_DOC_DEVICE) || (doc_dev_desc[dev].ChipID == DOC_ChipID_UNKNOWN)) { printf ("\n** Device %d not available\n", dev); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-37); return 1; } + SHOW_BOOT_PROGRESS (37); printf ("\nLoading from device %d: %s at 0x%lX (offset 0x%lX)\n", dev, doc_dev_desc[dev].name, doc_dev_desc[dev].physadr, @@ -262,9 +266,10 @@ int do_docboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) if (doc_rw (doc_dev_desc + dev, 1, offset, SECTORSIZE, NULL, (u_char *)addr)) { printf ("** Read error on %d\n", dev); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-38); return 1; } + SHOW_BOOT_PROGRESS (38); hdr = (image_header_t *)addr; @@ -276,16 +281,18 @@ int do_docboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) cnt -= SECTORSIZE; } else { puts ("\n** Bad Magic Number **\n"); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-39); return 1; } + SHOW_BOOT_PROGRESS (39); if (doc_rw (doc_dev_desc + dev, 1, offset + SECTORSIZE, cnt, NULL, (u_char *)(addr+SECTORSIZE))) { printf ("** Read error on %d\n", dev); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-40); return 1; } + SHOW_BOOT_PROGRESS (40); /* Loading ok, update default load address */ diff --git a/common/cmd_ide.c b/common/cmd_ide.c index e308474af..c74cde96e 100644 --- a/common/cmd_ide.c +++ b/common/cmd_ide.c @@ -185,6 +185,9 @@ static void input_data(int dev, ulong *sect_buf, int words); static void output_data(int dev, ulong *sect_buf, int words); static void ident_cpy (unsigned char *dest, unsigned char *src, unsigned int len); +#ifndef CFG_ATA_PORT_ADDR +#define CFG_ATA_PORT_ADDR(port) (port) +#endif #ifdef CONFIG_ATAPI static void atapi_inquiry(block_dev_desc_t *dev_desc); @@ -382,6 +385,7 @@ int do_diskboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) image_header_t *hdr; int rcode = 0; + SHOW_BOOT_PROGRESS (41); switch (argc) { case 1: addr = CFG_LOAD_ADDR; @@ -397,44 +401,50 @@ int do_diskboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) break; default: printf ("Usage:\n%s\n", cmdtp->usage); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-42); return 1; } + SHOW_BOOT_PROGRESS (42); if (!boot_device) { puts ("\n** No boot device **\n"); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-43); return 1; } + SHOW_BOOT_PROGRESS (43); dev = simple_strtoul(boot_device, &ep, 16); if (ide_dev_desc[dev].type==DEV_TYPE_UNKNOWN) { printf ("\n** Device %d not available\n", dev); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-44); return 1; } + SHOW_BOOT_PROGRESS (44); if (*ep) { if (*ep != ':') { puts ("\n** Invalid boot device, use `dev[:part]' **\n"); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-45); return 1; } part = simple_strtoul(++ep, NULL, 16); } + SHOW_BOOT_PROGRESS (45); if (get_partition_info (&ide_dev_desc[dev], part, &info)) { - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-46); return 1; } + SHOW_BOOT_PROGRESS (46); if ((strncmp((char *)info.type, BOOT_PART_TYPE, sizeof(info.type)) != 0) && (strncmp((char *)info.type, BOOT_PART_COMP, sizeof(info.type)) != 0)) { printf ("\n** Invalid partition type \"%.32s\"" " (expect \"" BOOT_PART_TYPE "\")\n", info.type); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-47); return 1; } + SHOW_BOOT_PROGRESS (47); printf ("\nLoading from IDE device %d, partition %d: " "Name: %.32s Type: %.32s\n", @@ -445,26 +455,29 @@ int do_diskboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) if (ide_dev_desc[dev].block_read (dev, info.start, 1, (ulong *)addr) != 1) { printf ("** Read error on %d:%d\n", dev, part); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-48); return 1; } + SHOW_BOOT_PROGRESS (48); hdr = (image_header_t *)addr; if (ntohl(hdr->ih_magic) != IH_MAGIC) { printf("\n** Bad Magic Number **\n"); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-49); return 1; } + SHOW_BOOT_PROGRESS (49); checksum = ntohl(hdr->ih_hcrc); hdr->ih_hcrc = 0; if (crc32 (0, (uchar *)hdr, sizeof(image_header_t)) != checksum) { puts ("\n** Bad Header Checksum **\n"); - SHOW_BOOT_PROGRESS (-2); + SHOW_BOOT_PROGRESS (-50); return 1; } + SHOW_BOOT_PROGRESS (50); hdr->ih_hcrc = htonl(checksum); /* restore checksum for later use */ print_image_hdr (hdr); @@ -477,9 +490,10 @@ int do_diskboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) if (ide_dev_desc[dev].block_read (dev, info.start+1, cnt, (ulong *)(addr+info.blksz)) != cnt) { printf ("** Read error on %d:%d\n", dev, part); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-51); return 1; } + SHOW_BOOT_PROGRESS (51); /* Loading ok, update default load address */ @@ -807,13 +821,13 @@ ide_outb(int dev, int port, unsigned char val) /* Ensure I/O operations complete */ EIEIO; - *((uchar *)(ATA_CURR_BASE(dev)+port)) = val; + *((u16 *)(ATA_CURR_BASE(dev)+CFG_ATA_PORT_ADDR(port))) = val; } #else /* ! __PPC__ */ static void __inline__ ide_outb(int dev, int port, unsigned char val) { - outb(val, ATA_CURR_BASE(dev)+port); + outb(val, ATA_CURR_BASE(dev)+CFG_ATA_PORT_ADDR(port)); } #endif /* __PPC__ */ @@ -825,7 +839,7 @@ ide_inb(int dev, int port) uchar val; /* Ensure I/O operations complete */ EIEIO; - val = *((uchar *)(ATA_CURR_BASE(dev)+port)); + val = *((u16 *)(ATA_CURR_BASE(dev)+CFG_ATA_PORT_ADDR(port))); debug ("ide_inb (dev= %d, port= 0x%x) : @ 0x%08lx -> 0x%02x\n", dev, port, (ATA_CURR_BASE(dev)+port), val); return (val); @@ -834,7 +848,7 @@ ide_inb(int dev, int port) static unsigned char __inline__ ide_inb(int dev, int port) { - return inb(ATA_CURR_BASE(dev)+port); + return inb(ATA_CURR_BASE(dev)+CFG_ATA_PORT_ADDR(port)); } #endif /* __PPC__ */ @@ -891,6 +905,9 @@ input_swap_data(int dev, ulong *sect_buf, int words) #ifdef __MIPS__ *dbuf++ = swab16p((u16*)pbuf); *dbuf++ = swab16p((u16*)pbuf); +#elif defined(CONFIG_PCS440EP) + *dbuf++ = *pbuf; + *dbuf++ = *pbuf; #else *dbuf++ = ld_le16(pbuf); *dbuf++ = ld_le16(pbuf); @@ -930,10 +947,18 @@ output_data(int dev, ulong *sect_buf, int words) pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG); dbuf = (ushort *)sect_buf; while (words--) { +#if defined(CONFIG_PCS440EP) + /* not tested, because CF was write protected */ + EIEIO; + *pbuf = ld_le16(dbuf++); + EIEIO; + *pbuf = ld_le16(dbuf++); +#else EIEIO; *pbuf = *dbuf++; EIEIO; *pbuf = *dbuf++; +#endif } #endif } @@ -981,10 +1006,17 @@ input_data(int dev, ulong *sect_buf, int words) debug("in input data base for read is %lx\n", (unsigned long) pbuf); while (words--) { +#if defined(CONFIG_PCS440EP) + EIEIO; + *dbuf++ = ld_le16(pbuf); + EIEIO; + *dbuf++ = ld_le16(pbuf); +#else EIEIO; *dbuf++ = *pbuf; EIEIO; *dbuf++ = *pbuf; +#endif } #endif } diff --git a/common/cmd_nand.c b/common/cmd_nand.c index b011b5e3d..b088150f3 100644 --- a/common/cmd_nand.c +++ b/common/cmd_nand.c @@ -486,17 +486,19 @@ static int nand_load_image(cmd_tbl_t *cmdtp, nand_info_t *nand, r = nand_read(nand, offset, &cnt, (u_char *) addr); if (r) { puts("** Read error\n"); - SHOW_BOOT_PROGRESS(-1); + SHOW_BOOT_PROGRESS(-56); return 1; } + SHOW_BOOT_PROGRESS(56); hdr = (image_header_t *) addr; if (ntohl(hdr->ih_magic) != IH_MAGIC) { printf("\n** Bad Magic Number 0x%x **\n", hdr->ih_magic); - SHOW_BOOT_PROGRESS(-1); + SHOW_BOOT_PROGRESS(-57); return 1; } + SHOW_BOOT_PROGRESS(57); print_image_hdr(hdr); @@ -505,9 +507,10 @@ static int nand_load_image(cmd_tbl_t *cmdtp, nand_info_t *nand, r = nand_read(nand, offset, &cnt, (u_char *) addr); if (r) { puts("** Read error\n"); - SHOW_BOOT_PROGRESS(-1); + SHOW_BOOT_PROGRESS(-58); return 1; } + SHOW_BOOT_PROGRESS(58); /* Loading ok, update default load address */ @@ -559,6 +562,7 @@ int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) } #endif + SHOW_BOOT_PROGRESS(52); switch (argc) { case 1: addr = CFG_LOAD_ADDR; @@ -582,23 +586,26 @@ int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) usage: #endif printf("Usage:\n%s\n", cmdtp->usage); - SHOW_BOOT_PROGRESS(-1); + SHOW_BOOT_PROGRESS(-53); return 1; } + SHOW_BOOT_PROGRESS(53); if (!boot_device) { puts("\n** No boot device **\n"); - SHOW_BOOT_PROGRESS(-1); + SHOW_BOOT_PROGRESS(-54); return 1; } + SHOW_BOOT_PROGRESS(54); idx = simple_strtoul(boot_device, NULL, 16); if (idx < 0 || idx >= CFG_MAX_NAND_DEVICE || !nand_info[idx].name) { printf("\n** Device %d not available\n", idx); - SHOW_BOOT_PROGRESS(-1); + SHOW_BOOT_PROGRESS(-55); return 1; } + SHOW_BOOT_PROGRESS(55); return nand_load_image(cmdtp, &nand_info[idx], offset, addr, argv[0]); } @@ -887,6 +894,7 @@ int do_nandboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) ulong offset = 0; image_header_t *hdr; int rcode = 0; + SHOW_BOOT_PROGRESS(52); switch (argc) { case 1: addr = CFG_LOAD_ADDR; @@ -907,24 +915,27 @@ int do_nandboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) break; default: printf ("Usage:\n%s\n", cmdtp->usage); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-53); return 1; } + SHOW_BOOT_PROGRESS(53); if (!boot_device) { puts ("\n** No boot device **\n"); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-54); return 1; } + SHOW_BOOT_PROGRESS(54); dev = simple_strtoul(boot_device, &ep, 16); if ((dev >= CFG_MAX_NAND_DEVICE) || (nand_dev_desc[dev].ChipID == NAND_ChipID_UNKNOWN)) { printf ("\n** Device %d not available\n", dev); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-55); return 1; } + SHOW_BOOT_PROGRESS(55); printf ("\nLoading from device %d: %s at 0x%lx (offset 0x%lx)\n", dev, nand_dev_desc[dev].name, nand_dev_desc[dev].IO_ADDR, @@ -933,9 +944,10 @@ int do_nandboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) if (nand_legacy_rw (nand_dev_desc + dev, NANDRW_READ, offset, SECTORSIZE, NULL, (u_char *)addr)) { printf ("** Read error on %d\n", dev); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-56); return 1; } + SHOW_BOOT_PROGRESS(56); hdr = (image_header_t *)addr; @@ -947,17 +959,19 @@ int do_nandboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) cnt -= SECTORSIZE; } else { printf ("\n** Bad Magic Number 0x%x **\n", ntohl(hdr->ih_magic)); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-57); return 1; } + SHOW_BOOT_PROGRESS(57); if (nand_legacy_rw (nand_dev_desc + dev, NANDRW_READ, offset + SECTORSIZE, cnt, NULL, (u_char *)(addr+SECTORSIZE))) { printf ("** Read error on %d\n", dev); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-58); return 1; } + SHOW_BOOT_PROGRESS(58); /* Loading ok, update default load address */ diff --git a/common/cmd_net.c b/common/cmd_net.c index 2cb2c5d34..e9d552e23 100644 --- a/common/cmd_net.c +++ b/common/cmd_net.c @@ -30,6 +30,13 @@ #if (CONFIG_COMMANDS & CFG_CMD_NET) +#ifdef CONFIG_SHOW_BOOT_PROGRESS +# include +extern void show_boot_progress (int val); +# define SHOW_BOOT_PROGRESS(arg) show_boot_progress (arg) +#else +# define SHOW_BOOT_PROGRESS(arg) +#endif extern int do_bootm (cmd_tbl_t *, int, int, char *[]); @@ -184,18 +191,25 @@ netboot_common (proto_t proto, cmd_tbl_t *cmdtp, int argc, char *argv[]) break; default: printf ("Usage:\n%s\n", cmdtp->usage); + SHOW_BOOT_PROGRESS(-80); return 1; } - if ((size = NetLoop(proto)) < 0) + SHOW_BOOT_PROGRESS(80); + if ((size = NetLoop(proto)) < 0) { + SHOW_BOOT_PROGRESS(-81); return 1; + } + SHOW_BOOT_PROGRESS(81); /* NetLoop ok, update environment */ netboot_update_env(); /* done if no file was loaded (no errors though) */ - if (size == 0) + if (size == 0) { + SHOW_BOOT_PROGRESS(-82); return 0; + } /* flush cache */ flush_cache(load_addr, size); @@ -208,14 +222,22 @@ netboot_common (proto_t proto, cmd_tbl_t *cmdtp, int argc, char *argv[]) printf ("Automatic boot of image at addr 0x%08lX ...\n", load_addr); + SHOW_BOOT_PROGRESS(82); rcode = do_bootm (cmdtp, 0, 1, local_args); } #ifdef CONFIG_AUTOSCRIPT if (((s = getenv("autoscript")) != NULL) && (strcmp(s,"yes") == 0)) { printf("Running autoscript at addr 0x%08lX ...\n", load_addr); + SHOW_BOOT_PROGRESS(83); rcode = autoscript (load_addr); } +#endif +#if defined(CONFIG_SHOW_BOOT_PROGRESS) + if (rcode < 0) + SHOW_BOOT_PROGRESS(-83); + else + SHOW_BOOT_PROGRESS(84); #endif return rcode; } diff --git a/common/cmd_reiser.c b/common/cmd_reiser.c index 09c86e66d..d83c31ab3 100644 --- a/common/cmd_reiser.c +++ b/common/cmd_reiser.c @@ -90,7 +90,7 @@ int do_reiserls (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) } if (!reiserfs_mount(part_length)) { - printf ("** Bad Reisefs partition or disk - %s %d:%d **\n", argv[1], dev, part); + printf ("** Bad Reiserfs partition or disk - %s %d:%d **\n", argv[1], dev, part); return 1; } @@ -183,7 +183,7 @@ int do_reiserload (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) return 1; } - if (strncmp(info.type, BOOT_PART_TYPE, sizeof(info.type)) != 0) { + if (strncmp((char *)info.type, BOOT_PART_TYPE, sizeof(info.type)) != 0) { printf ("\n** Invalid partition type \"%.32s\"" " (expect \"" BOOT_PART_TYPE "\")\n", info.type); @@ -204,7 +204,7 @@ int do_reiserload (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) } if (!reiserfs_mount(part_length)) { - printf ("** Bad Reisefs partition or disk - %s %d:%d **\n", argv[1], dev, part); + printf ("** Bad Reiserfs partition or disk - %s %d:%d **\n", argv[1], dev, part); return 1; } diff --git a/common/env_common.c b/common/env_common.c index eb33422af..0462cad6d 100644 --- a/common/env_common.c +++ b/common/env_common.c @@ -232,7 +232,7 @@ void env_relocate (void) puts ("Using default environment\n\n"); #else puts ("*** Warning - bad CRC, using default environment\n\n"); - SHOW_BOOT_PROGRESS (-1); + SHOW_BOOT_PROGRESS (-60); #endif if (sizeof(default_environment) > ENV_SIZE) diff --git a/cpu/ppc4xx/44x_spd_ddr.c b/cpu/ppc4xx/44x_spd_ddr.c index c500d3f24..8621aa00c 100644 --- a/cpu/ppc4xx/44x_spd_ddr.c +++ b/cpu/ppc4xx/44x_spd_ddr.c @@ -70,6 +70,13 @@ #define ONE_BILLION 1000000000 +#if defined(CONFIG_PPC4xx_USE_SPD_DDR_INIT_HANG) +extern void spd_ddr_init_hang (void); +#define HANG() spd_ddr_init_hang() +#else +#define HANG() hang() +#endif + /*----------------------------------------------------------------------------- | Memory Controller Options 0 +-----------------------------------------------------------------------------*/ @@ -467,7 +474,7 @@ static void get_spd_info(unsigned long *dimm_populated, if (dimm_found == FALSE) { printf("ERROR - No memory installed. Install a DDR-SDRAM DIMM.\n\n"); - hang(); + HANG(); } } @@ -490,7 +497,7 @@ static void check_mem_type(unsigned long *dimm_populated, dimm_num); printf("Only DDR SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); + HANG(); break; } } @@ -510,7 +517,7 @@ static void check_volt_type(unsigned long *dimm_populated, if (voltage_type != 0x04) { printf("ERROR: DIMM %lu with unsupported voltage level.\n", dimm_num); - hang(); + HANG(); } else { debug("DIMM %lu voltage level supported.\n", dimm_num); } @@ -581,7 +588,7 @@ static void program_cfg0(unsigned long *dimm_populated, printf("WARNING: DIMM with datawidth of %lu bits.\n", data_width); printf("Only DIMMs with 32 or 64 bit datawidths supported.\n"); - hang(); + HANG(); } break; } @@ -769,7 +776,7 @@ static void program_tr0(unsigned long *dimm_populated, if ((tcyc_reg & 0x0F) >= 10) { printf("ERROR: Tcyc incorrect for DIMM in slot %lu\n", dimm_num); - hang(); + HANG(); } cycle_time_ns_x_10[cas_index] = @@ -849,7 +856,7 @@ static void program_tr0(unsigned long *dimm_populated, printf("ERROR: No supported CAS latency with the installed DIMMs.\n"); printf("Only CAS latencies of 2.0, 2.5, and 3.0 are supported.\n"); printf("Make sure the PLB speed is within the supported range.\n"); - hang(); + HANG(); } /* @@ -1008,6 +1015,7 @@ static int short_mem_test(void) */ for (i = 0; i < NUMMEMTESTS; i++) { for (j = 0; j < NUMMEMWORDS; j++) { +//printf("bank enabled base:%x\n", &membase[j]); membase[j] = test[i][j]; ppcDcbf((unsigned long)&(membase[j])); } @@ -1160,7 +1168,7 @@ static void program_tr1(void) */ if (window_found == FALSE) { printf("ERROR: Cannot determine a common read delay.\n"); - hang(); + HANG(); } /* @@ -1310,7 +1318,7 @@ static unsigned long program_bxcr(unsigned long *dimm_populated, printf("ERROR: Unsupported value for the banksize: %d.\n", bank_size_id); printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); + HANG(); } switch (num_col_addr) { @@ -1332,7 +1340,7 @@ static unsigned long program_bxcr(unsigned long *dimm_populated, printf("ERROR: Unsupported value for number of " "column addresses: %d.\n", num_col_addr); printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); + HANG(); } /* diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c index 48b9ee2f7..d748daee0 100644 --- a/cpu/ppc4xx/44x_spd_ddr2.c +++ b/cpu/ppc4xx/44x_spd_ddr2.c @@ -129,6 +129,13 @@ #define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE /* disable caching on SDRAM */ #endif +#if defined(CONFIG_PPC4xx_USE_SPD_DDR_INIT_HANG) +extern void spd_ddr_init_hang (void); +#define HANG() spd_ddr_init_hang() +#else +#define HANG() hang() +#endif + /* Private Structure Definitions */ /* enum only to ease code for cas latency setting */ @@ -582,7 +589,7 @@ static void get_spd_info(unsigned long *dimm_populated, if (dimm_found == FALSE) { printf("ERROR - No memory installed. Install a DDR-SDRAM DIMM.\n\n"); - hang(); + HANG(); } } @@ -629,42 +636,42 @@ static void check_mem_type(unsigned long *dimm_populated, "slot %d.\n", (unsigned int)dimm_num); printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); + HANG(); break; case 2: printf("ERROR: EDO DIMM detected in slot %d.\n", (unsigned int)dimm_num); printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); + HANG(); break; case 3: printf("ERROR: Pipelined Nibble DIMM detected in slot %d.\n", (unsigned int)dimm_num); printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); + HANG(); break; case 4: printf("ERROR: SDRAM DIMM detected in slot %d.\n", (unsigned int)dimm_num); printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); + HANG(); break; case 5: printf("ERROR: Multiplexed ROM DIMM detected in slot %d.\n", (unsigned int)dimm_num); printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); + HANG(); break; case 6: printf("ERROR: SGRAM DIMM detected in slot %d.\n", (unsigned int)dimm_num); printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); + HANG(); break; case 7: debug("DIMM slot %d: DDR1 SDRAM detected\n", dimm_num); @@ -679,7 +686,7 @@ static void check_mem_type(unsigned long *dimm_populated, (unsigned int)dimm_num); printf("Only DDR1 and DDR2 SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); + HANG(); break; } } @@ -689,7 +696,7 @@ static void check_mem_type(unsigned long *dimm_populated, && (dimm_populated[dimm_num] != SDRAM_NONE) && (dimm_populated[dimm_num-1] != dimm_populated[dimm_num])) { printf("ERROR: DIMM's DDR1 and DDR2 type can not be mixed.\n"); - hang(); + HANG(); } } } @@ -764,7 +771,7 @@ static void check_frequency(unsigned long *dimm_populated, (unsigned int)(calc_cycle_time*10)); printf("Replace the DIMM, or change DDR frequency via " "strapping bits.\n\n"); - hang(); + HANG(); } } } @@ -796,7 +803,7 @@ static void check_rank_number(unsigned long *dimm_populated, "slot %d is not supported.\n", dimm_rank, dimm_num); printf("Only %d ranks are supported for all DIMM.\n", MAXRANKS); printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); + HANG(); } else total_rank += dimm_rank; } @@ -805,7 +812,7 @@ static void check_rank_number(unsigned long *dimm_populated, "for all slots.\n", (unsigned int)total_rank); printf("Only %d ranks are supported for all DIMM.\n", MAXRANKS); printf("Remove one of the DIMM modules.\n\n"); - hang(); + HANG(); } } } @@ -830,28 +837,28 @@ static void check_voltage_type(unsigned long *dimm_populated, printf("This DIMM is 5.0 Volt/TTL.\n"); printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n", (unsigned int)dimm_num); - hang(); + HANG(); break; case 0x01: printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n"); printf("This DIMM is LVTTL.\n"); printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n", (unsigned int)dimm_num); - hang(); + HANG(); break; case 0x02: printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n"); printf("This DIMM is 1.5 Volt.\n"); printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n", (unsigned int)dimm_num); - hang(); + HANG(); break; case 0x03: printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n"); printf("This DIMM is 3.3 Volt/TTL.\n"); printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n", (unsigned int)dimm_num); - hang(); + HANG(); break; case 0x04: /* 2.5 Voltage only for DDR1 */ @@ -863,7 +870,7 @@ static void check_voltage_type(unsigned long *dimm_populated, printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n"); printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n", (unsigned int)dimm_num); - hang(); + HANG(); break; } } @@ -1006,13 +1013,13 @@ static void program_copt1(unsigned long *dimm_populated, if ((dimm_populated[0] != SDRAM_NONE) && (dimm_populated[1] != SDRAM_NONE)) { if (buf0 != buf1) { printf("ERROR: DIMM's buffered/unbuffered, registered, clocking don't match.\n"); - hang(); + HANG(); } } if ((dimm_64bit == TRUE) && (dimm_32bit == TRUE)) { printf("ERROR: Cannot mix 32 bit and 64 bit DDR-SDRAM DIMMs together.\n"); - hang(); + HANG(); } else if ((dimm_64bit == TRUE) && (dimm_32bit == FALSE)) { mcopt1 |= SDRAM_MCOPT1_DMWD_64; @@ -1020,7 +1027,7 @@ static void program_copt1(unsigned long *dimm_populated, mcopt1 |= SDRAM_MCOPT1_DMWD_32; } else { printf("ERROR: Please install only 32 or 64 bit DDR-SDRAM DIMMs.\n\n"); - hang(); + HANG(); } if (ecc_enabled == TRUE) @@ -1209,7 +1216,7 @@ static void program_initplr(unsigned long *dimm_populated, break; default: printf("ERROR: ucode error on selected_cas value %d", selected_cas); - hang(); + HANG(); break; } @@ -1241,7 +1248,7 @@ static void program_initplr(unsigned long *dimm_populated, break; default: printf("ERROR: write recovery not support (%d)", write_recovery); - hang(); + HANG(); break; } #else @@ -1259,7 +1266,7 @@ static void program_initplr(unsigned long *dimm_populated, ods = ODS_REDUCED; } else { printf("ERROR: Unsupported number of DIMM's (%d)", total_dimm); - hang(); + HANG(); } mr = CMD_EMR | SELECT_MR | BURST_LEN_4 | wr | cas; @@ -1284,7 +1291,7 @@ static void program_initplr(unsigned long *dimm_populated, mtsdram(SDRAM_INITPLR13, 0x80800000 | emr); /* EMR OCD Exit */ } else { printf("ERROR: ucode error as unknown DDR type in program_initplr"); - hang(); + HANG(); } } @@ -1389,7 +1396,7 @@ static void program_mode(unsigned long *dimm_populated, } else { printf("ERROR: SPD reported Tcyc is incorrect for DIMM " "in slot %d\n", (unsigned int)dimm_num); - hang(); + HANG(); } } else { /* Convert from hex to decimal */ @@ -1526,7 +1533,7 @@ static void program_mode(unsigned long *dimm_populated, printf("ERROR: Cannot find a supported CAS latency with the installed DIMMs.\n"); printf("Only DIMMs DDR1 with CAS latencies of 2.0, 2.5, and 3.0 are supported.\n"); printf("Make sure the PLB speed is within the supported range of the DIMMs.\n\n"); - hang(); + HANG(); } } else { /* DDR2 */ debug("cas_3_0_available=%d\n", cas_3_0_available); @@ -1549,7 +1556,7 @@ static void program_mode(unsigned long *dimm_populated, cas_3_0_available, cas_4_0_available, cas_5_0_available); printf("sdram_freq=%d cycle3=%d cycle4=%d cycle5=%d\n\n", sdram_freq, cycle_3_0_clk, cycle_4_0_clk, cycle_5_0_clk); - hang(); + HANG(); } } @@ -1658,7 +1665,7 @@ static void program_rtr(unsigned long *dimm_populated, printf("ERROR: DIMM %d unsupported refresh rate/type.\n", (unsigned int)dimm_num); printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); + HANG(); break; } @@ -2066,7 +2073,7 @@ static void program_bxcf(unsigned long *dimm_populated, printf("ERROR: Unsupported value for number of " "column addresses: %d.\n", (unsigned int)num_col_addr); printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); + HANG(); } } @@ -2148,7 +2155,7 @@ static void program_memory_queue(unsigned long *dimm_populated, printf("ERROR: Unsupported value for the banksize: %d.\n", (unsigned int)rank_size_id); printf("Replace the DIMM module with a supported DIMM.\n\n"); - hang(); + HANG(); } if ((dimm_populated[dimm_num] != SDRAM_NONE) && (dimm_num == 1)) @@ -2693,7 +2700,7 @@ calibration_loop: printf("\nERROR: Cannot determine a common read delay for the " "DIMM(s) installed.\n"); debug("%s[%d] ERROR : \n", __FUNCTION__,__LINE__); - hang(); + HANG(); } blank_string(strlen(str)); @@ -2849,7 +2856,7 @@ static void test(void) if (window_found == FALSE) { printf("ERROR: Cannot determine a common read delay for the " "DIMM(s) installed.\n"); - hang(); + HANG(); } /*------------------------------------------------------------------ diff --git a/disk/part.c b/disk/part.c index 255b14069..6ab585707 100755 --- a/disk/part.c +++ b/disk/part.c @@ -180,7 +180,6 @@ void dev_print (block_dev_desc_t *dev_desc) (CONFIG_COMMANDS & CFG_CMD_SCSI) || \ (CONFIG_COMMANDS & CFG_CMD_USB) || \ defined(CONFIG_MMC) || \ - (defined(CONFIG_MMC) && defined(CONFIG_LPC2292)) || \ defined(CONFIG_SYSTEMACE) ) #if defined(CONFIG_MAC_PARTITION) || \ @@ -223,7 +222,7 @@ void init_part (block_dev_desc_t * dev_desc) int get_partition_info (block_dev_desc_t *dev_desc, int part , disk_partition_t *info) { - switch (dev_desc->part_type) { + switch (dev_desc->part_type) { #ifdef CONFIG_MAC_PARTITION case PART_TYPE_MAC: if (get_partition_info_mac(dev_desc,part,info) == 0) { diff --git a/fs/fat/fat.c b/fs/fat/fat.c index 300760836..21a00b80d 100755 --- a/fs/fat/fat.c +++ b/fs/fat/fat.c @@ -70,10 +70,11 @@ int fat_register_device(block_dev_desc_t *dev_desc, int part_no) { unsigned char buffer[SECTOR_SIZE]; + disk_partition_t info; if (!dev_desc->block_read) return -1; - cur_dev=dev_desc; + cur_dev = dev_desc; /* check if we have a MBR (on floppies we have only a PBR) */ if (dev_desc->block_read (dev_desc->dev, 0, 1, (ulong *) buffer) != 1) { printf ("** Can't read from device %d **\n", dev_desc->dev); @@ -84,36 +85,39 @@ fat_register_device(block_dev_desc_t *dev_desc, int part_no) /* no signature found */ return -1; } - if(!strncmp((char *)&buffer[DOS_FS_TYPE_OFFSET],"FAT",3)) { - /* ok, we assume we are on a PBR only */ - cur_part = 1; - part_offset=0; - } - else { #if ((CONFIG_COMMANDS & CFG_CMD_IDE) || \ (CONFIG_COMMANDS & CFG_CMD_SCSI) || \ (CONFIG_COMMANDS & CFG_CMD_USB) || \ - (defined(CONFIG_MMC) && defined(CONFIG_LPC2292)) || \ + (defined(CONFIG_MMC)) || \ defined(CONFIG_SYSTEMACE) ) - disk_partition_t info; - if(!get_partition_info(dev_desc, part_no, &info)) { - part_offset = info.start; - cur_part = part_no; - } - else { - printf ("** Partition %d not valid on device %d **\n",part_no,dev_desc->dev); - return -1; - } + /* First we assume, there is a MBR */ + if (!get_partition_info (dev_desc, part_no, &info)) { + part_offset = info.start; + cur_part = part_no; + } else if (!strncmp((char *)&buffer[DOS_FS_TYPE_OFFSET], "FAT", 3)) { + /* ok, we assume we are on a PBR only */ + cur_part = 1; + part_offset = 0; + } else { + printf ("** Partition %d not valid on device %d **\n", part_no, dev_desc->dev); + return -1; + } #else + if(!strncmp((char *)&buffer[DOS_FS_TYPE_OFFSET],"FAT",3)) { + /* ok, we assume we are on a PBR only */ + cur_part = 1; + part_offset = 0; + info.start = part_offset; + } else { /* FIXME we need to determine the start block of the * partition where the DOS FS resides. This can be done * by using the get_partition_info routine. For this * purpose the libpart must be included. */ - part_offset=32; + part_offset = 32; cur_part = 1; -#endif } +#endif return 0; } diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h index 23bdfc8df..d47180882 100644 --- a/include/configs/pcs440ep.h +++ b/include/configs/pcs440ep.h @@ -105,19 +105,27 @@ #ifdef CFG_ENV_IS_IN_FLASH #define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +#define CONFIG_ENV_OVERWRITE 1 /* Address and size of Redundant Environment Sector */ #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #endif /* CFG_ENV_IS_IN_FLASH */ +#define ENV_NAME_REVLEV "revision_level" +#define ENV_NAME_SOLDER "solder_switch" +#define ENV_NAME_DIP "dip" + /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ #undef CONFIG_DDR_ECC /* don't use ECC */ #define SPD_EEPROM_ADDRESS {0x50} +#define CONFIG_PROG_SDRAM_TLB 1 +#define CONFIG_PPC4xx_USE_SPD_DDR_INIT_HANG 1 /*----------------------------------------------------------------------- * I2C @@ -142,6 +150,8 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "hostname=pcs440ep\0" \ + "use_eeprom_ethaddr=default\0" \ + "cs_test=off\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ @@ -172,6 +182,36 @@ #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ #endif +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +/* check U-Boot image with SHA1 sum */ +#define CONFIG_SHA1_CHECK_UB_IMG 1 +#define CONFIG_SHA1_START CFG_MONITOR_BASE +#define CONFIG_SHA1_LEN CFG_MONITOR_LEN + +/*----------------------------------------------------------------------- + * Definitions for status LED + */ +#define CONFIG_STATUS_LED 1 /* Status LED enabled */ +#define CONFIG_BOARD_SPECIFIC_LED 1 + +#define STATUS_LED_BIT 0x08 /* LED 1 is on GPIO_PPC_1 */ +#define STATUS_LED_PERIOD ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE STATUS_LED_OFF +#define STATUS_LED_BIT1 0x04 /* LED 2 is on GPIO_PPC_2 */ +#define STATUS_LED_PERIOD1 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE1 STATUS_LED_ON +#define STATUS_LED_BIT2 0x02 /* LED 3 is on GPIO_PPC_3 */ +#define STATUS_LED_PERIOD2 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE2 STATUS_LED_OFF +#define STATUS_LED_BIT3 0x01 /* LED 4 is on GPIO_PPC_4 */ +#define STATUS_LED_PERIOD3 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE3 STATUS_LED_OFF + +#define CONFIG_SHOW_BOOT_PROGRESS 1 + #define CONFIG_BAUDRATE 115200 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ @@ -213,7 +253,10 @@ CFG_CMD_DIAG | \ CFG_CMD_EEPROM | \ CFG_CMD_ELF | \ + CFG_CMD_EXT2 | \ + CFG_CMD_FAT | \ CFG_CMD_I2C | \ + CFG_CMD_IDE | \ CFG_CMD_IRQ | \ CFG_CMD_MII | \ CFG_CMD_NET | \ @@ -221,9 +264,8 @@ CFG_CMD_PCI | \ CFG_CMD_PING | \ CFG_CMD_REGINFO | \ + CFG_CMD_REISER | \ CFG_CMD_SDRAM | \ - CFG_CMD_EXT2 | \ - CFG_CMD_FAT | \ CFG_CMD_USB ) @@ -410,4 +452,39 @@ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif +/*----------------------------------------------------------------------- + * IDE/ATA stuff Supports IDE harddisk + *----------------------------------------------------------------------- + */ + +#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 2 drives per IDE bus */ + +#define CONFIG_IDE_PREINIT 1 +#define CONFIG_IDE_RESET 1 + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR CFG_CF1 + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET 0 + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET (0x0000) + +/* This addresses need to be shifted one place to the left + * ( bus per_addr 20 -30 is connectsd on CF bus A10-A0) + * This values are shifted + */ +#define CFG_ATA_PORT_ADDR(port) ((port) << 1) + #endif /* __CONFIG_H */ diff --git a/include/sha1.h b/include/sha1.h new file mode 100644 index 000000000..3030f2975 --- /dev/null +++ b/include/sha1.h @@ -0,0 +1,115 @@ +/** + * \file sha1.h + * based from http://xyssl.org/code/source/sha1/ + * FIPS-180-1 compliant SHA-1 implementation + * + * Copyright (C) 2003-2006 Christophe Devine + * + * This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU Lesser General Public + * License, version 2.1 as published by the Free Software Foundation. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * Lesser General Public License for more details. + * + * You should have received a copy of the GNU Lesser General Public + * License along with this library; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ +/* + * The SHA-1 standard was published by NIST in 1993. + * + * http://www.itl.nist.gov/fipspubs/fip180-1.htm + */ +#ifndef _SHA1_H +#define _SHA1_H + +#ifdef __cplusplus +extern "C" { +#endif + +#define SHA1_SUM_POS -0x20 +#define SHA1_SUM_LEN 20 + +/** + * \brief SHA-1 context structure + */ +typedef struct +{ + unsigned long total[2]; /*!< number of bytes processed */ + unsigned long state[5]; /*!< intermediate digest state */ + unsigned char buffer[64]; /*!< data block being processed */ +} +sha1_context; + +/** + * \brief SHA-1 context setup + * + * \param ctx SHA-1 context to be initialized + */ +void sha1_starts( sha1_context *ctx ); + +/** + * \brief SHA-1 process buffer + * + * \param ctx SHA-1 context + * \param input buffer holding the data + * \param ilen length of the input data + */ +void sha1_update( sha1_context *ctx, unsigned char *input, int ilen ); + +/** + * \brief SHA-1 final digest + * + * \param ctx SHA-1 context + * \param output SHA-1 checksum result + */ +void sha1_finish( sha1_context *ctx, unsigned char output[20] ); + +/** + * \brief Output = SHA-1( input buffer ) + * + * \param input buffer holding the data + * \param ilen length of the input data + * \param output SHA-1 checksum result + */ +void sha1_csum( unsigned char *input, int ilen, + unsigned char output[20] ); + +/** + * \brief Output = SHA-1( file contents ) + * + * \param path input file name + * \param output SHA-1 checksum result + * \return 0 if successful, or 1 if fopen failed + */ +int sha1_file( char *path, unsigned char output[20] ); + +/** + * \brief Output = HMAC-SHA-1( input buffer, hmac key ) + * + * \param key HMAC secret key + * \param keylen length of the HMAC key + * \param input buffer holding the data + * \param ilen length of the input data + * \param output HMAC-SHA-1 result + */ +void sha1_hmac( unsigned char *key, int keylen, + unsigned char *input, int ilen, + unsigned char output[20] ); + +/** + * \brief Checkup routine + * + * \return 0 if successful, or 1 if the test failed + */ +int sha1_self_test( void ); + +#ifdef __cplusplus +} +#endif + +#endif /* sha1.h */ diff --git a/include/status_led.h b/include/status_led.h index 71a202fe3..a64681425 100644 --- a/include/status_led.h +++ b/include/status_led.h @@ -367,6 +367,13 @@ void status_led_set (int led, int state); #define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ +#elif defined(CONFIG_BOARD_SPECIFIC_LED) +/* led_id_t is unsigned long mask */ +typedef unsigned long led_id_t; + +extern void __led_toggle (led_id_t mask); +extern void __led_init (led_id_t mask, int state); +extern void __led_set (led_id_t mask, int state); #else # error Status LED configuration missing #endif diff --git a/lib_generic/Makefile b/lib_generic/Makefile index f012cab7d..b2091c5e7 100644 --- a/lib_generic/Makefile +++ b/lib_generic/Makefile @@ -27,7 +27,7 @@ LIB = $(obj)libgeneric.a COBJS = bzlib.o bzlib_crctable.o bzlib_decompress.o \ bzlib_randtable.o bzlib_huffman.o \ - crc32.o ctype.o display_options.o ldiv.o \ + crc32.o ctype.o display_options.o ldiv.o sha1.o \ string.o vsprintf.o zlib.o SRCS := $(COBJS:.o=.c) diff --git a/lib_generic/sha1.c b/lib_generic/sha1.c new file mode 100644 index 000000000..0522d7ce6 --- /dev/null +++ b/lib_generic/sha1.c @@ -0,0 +1,430 @@ +/* + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * based on: + * FIPS-180-1 compliant SHA-1 implementation + * + * Copyright (C) 2003-2006 Christophe Devine + * + * This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU Lesser General Public + * License, version 2.1 as published by the Free Software Foundation. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * Lesser General Public License for more details. + * + * You should have received a copy of the GNU Lesser General Public + * License along with this library; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ +/* + * The SHA-1 standard was published by NIST in 1993. + * + * http://www.itl.nist.gov/fipspubs/fip180-1.htm + */ + +#ifndef _CRT_SECURE_NO_DEPRECATE +#define _CRT_SECURE_NO_DEPRECATE 1 +#endif + +#include +#include "sha1.h" + +/* + * 32-bit integer manipulation macros (big endian) + */ +#ifndef GET_UINT32_BE +#define GET_UINT32_BE(n,b,i) \ +{ \ + (n) = ( (unsigned long) (b)[(i) ] << 24 ) \ + | ( (unsigned long) (b)[(i) + 1] << 16 ) \ + | ( (unsigned long) (b)[(i) + 2] << 8 ) \ + | ( (unsigned long) (b)[(i) + 3] ); \ +} +#endif +#ifndef PUT_UINT32_BE +#define PUT_UINT32_BE(n,b,i) \ +{ \ + (b)[(i) ] = (unsigned char) ( (n) >> 24 ); \ + (b)[(i) + 1] = (unsigned char) ( (n) >> 16 ); \ + (b)[(i) + 2] = (unsigned char) ( (n) >> 8 ); \ + (b)[(i) + 3] = (unsigned char) ( (n) ); \ +} +#endif + +/* + * SHA-1 context setup + */ +void sha1_starts( sha1_context *ctx ) +{ + ctx->total[0] = 0; + ctx->total[1] = 0; + + ctx->state[0] = 0x67452301; + ctx->state[1] = 0xEFCDAB89; + ctx->state[2] = 0x98BADCFE; + ctx->state[3] = 0x10325476; + ctx->state[4] = 0xC3D2E1F0; +} + +static void sha1_process( sha1_context *ctx, unsigned char data[64] ) +{ + unsigned long temp, W[16], A, B, C, D, E; + + GET_UINT32_BE( W[0], data, 0 ); + GET_UINT32_BE( W[1], data, 4 ); + GET_UINT32_BE( W[2], data, 8 ); + GET_UINT32_BE( W[3], data, 12 ); + GET_UINT32_BE( W[4], data, 16 ); + GET_UINT32_BE( W[5], data, 20 ); + GET_UINT32_BE( W[6], data, 24 ); + GET_UINT32_BE( W[7], data, 28 ); + GET_UINT32_BE( W[8], data, 32 ); + GET_UINT32_BE( W[9], data, 36 ); + GET_UINT32_BE( W[10], data, 40 ); + GET_UINT32_BE( W[11], data, 44 ); + GET_UINT32_BE( W[12], data, 48 ); + GET_UINT32_BE( W[13], data, 52 ); + GET_UINT32_BE( W[14], data, 56 ); + GET_UINT32_BE( W[15], data, 60 ); + +#define S(x,n) ((x << n) | ((x & 0xFFFFFFFF) >> (32 - n))) + +#define R(t) \ +( \ + temp = W[(t - 3) & 0x0F] ^ W[(t - 8) & 0x0F] ^ \ + W[(t - 14) & 0x0F] ^ W[ t & 0x0F], \ + ( W[t & 0x0F] = S(temp,1) ) \ +) + +#define P(a,b,c,d,e,x) \ +{ \ + e += S(a,5) + F(b,c,d) + K + x; b = S(b,30); \ +} + + A = ctx->state[0]; + B = ctx->state[1]; + C = ctx->state[2]; + D = ctx->state[3]; + E = ctx->state[4]; + +#define F(x,y,z) (z ^ (x & (y ^ z))) +#define K 0x5A827999 + + P( A, B, C, D, E, W[0] ); + P( E, A, B, C, D, W[1] ); + P( D, E, A, B, C, W[2] ); + P( C, D, E, A, B, W[3] ); + P( B, C, D, E, A, W[4] ); + P( A, B, C, D, E, W[5] ); + P( E, A, B, C, D, W[6] ); + P( D, E, A, B, C, W[7] ); + P( C, D, E, A, B, W[8] ); + P( B, C, D, E, A, W[9] ); + P( A, B, C, D, E, W[10] ); + P( E, A, B, C, D, W[11] ); + P( D, E, A, B, C, W[12] ); + P( C, D, E, A, B, W[13] ); + P( B, C, D, E, A, W[14] ); + P( A, B, C, D, E, W[15] ); + P( E, A, B, C, D, R(16) ); + P( D, E, A, B, C, R(17) ); + P( C, D, E, A, B, R(18) ); + P( B, C, D, E, A, R(19) ); + +#undef K +#undef F + +#define F(x,y,z) (x ^ y ^ z) +#define K 0x6ED9EBA1 + + P( A, B, C, D, E, R(20) ); + P( E, A, B, C, D, R(21) ); + P( D, E, A, B, C, R(22) ); + P( C, D, E, A, B, R(23) ); + P( B, C, D, E, A, R(24) ); + P( A, B, C, D, E, R(25) ); + P( E, A, B, C, D, R(26) ); + P( D, E, A, B, C, R(27) ); + P( C, D, E, A, B, R(28) ); + P( B, C, D, E, A, R(29) ); + P( A, B, C, D, E, R(30) ); + P( E, A, B, C, D, R(31) ); + P( D, E, A, B, C, R(32) ); + P( C, D, E, A, B, R(33) ); + P( B, C, D, E, A, R(34) ); + P( A, B, C, D, E, R(35) ); + P( E, A, B, C, D, R(36) ); + P( D, E, A, B, C, R(37) ); + P( C, D, E, A, B, R(38) ); + P( B, C, D, E, A, R(39) ); + +#undef K +#undef F + +#define F(x,y,z) ((x & y) | (z & (x | y))) +#define K 0x8F1BBCDC + + P( A, B, C, D, E, R(40) ); + P( E, A, B, C, D, R(41) ); + P( D, E, A, B, C, R(42) ); + P( C, D, E, A, B, R(43) ); + P( B, C, D, E, A, R(44) ); + P( A, B, C, D, E, R(45) ); + P( E, A, B, C, D, R(46) ); + P( D, E, A, B, C, R(47) ); + P( C, D, E, A, B, R(48) ); + P( B, C, D, E, A, R(49) ); + P( A, B, C, D, E, R(50) ); + P( E, A, B, C, D, R(51) ); + P( D, E, A, B, C, R(52) ); + P( C, D, E, A, B, R(53) ); + P( B, C, D, E, A, R(54) ); + P( A, B, C, D, E, R(55) ); + P( E, A, B, C, D, R(56) ); + P( D, E, A, B, C, R(57) ); + P( C, D, E, A, B, R(58) ); + P( B, C, D, E, A, R(59) ); + +#undef K +#undef F + +#define F(x,y,z) (x ^ y ^ z) +#define K 0xCA62C1D6 + + P( A, B, C, D, E, R(60) ); + P( E, A, B, C, D, R(61) ); + P( D, E, A, B, C, R(62) ); + P( C, D, E, A, B, R(63) ); + P( B, C, D, E, A, R(64) ); + P( A, B, C, D, E, R(65) ); + P( E, A, B, C, D, R(66) ); + P( D, E, A, B, C, R(67) ); + P( C, D, E, A, B, R(68) ); + P( B, C, D, E, A, R(69) ); + P( A, B, C, D, E, R(70) ); + P( E, A, B, C, D, R(71) ); + P( D, E, A, B, C, R(72) ); + P( C, D, E, A, B, R(73) ); + P( B, C, D, E, A, R(74) ); + P( A, B, C, D, E, R(75) ); + P( E, A, B, C, D, R(76) ); + P( D, E, A, B, C, R(77) ); + P( C, D, E, A, B, R(78) ); + P( B, C, D, E, A, R(79) ); + +#undef K +#undef F + + ctx->state[0] += A; + ctx->state[1] += B; + ctx->state[2] += C; + ctx->state[3] += D; + ctx->state[4] += E; +} + +/* + * SHA-1 process buffer + */ +void sha1_update( sha1_context *ctx, unsigned char *input, int ilen ) +{ + int fill; + unsigned long left; + + if( ilen <= 0 ) + return; + + left = ctx->total[0] & 0x3F; + fill = 64 - left; + + ctx->total[0] += ilen; + ctx->total[0] &= 0xFFFFFFFF; + + if( ctx->total[0] < (unsigned long) ilen ) + ctx->total[1]++; + + if( left && ilen >= fill ) + { + memcpy( (void *) (ctx->buffer + left), + (void *) input, fill ); + sha1_process( ctx, ctx->buffer ); + input += fill; + ilen -= fill; + left = 0; + } + + while( ilen >= 64 ) + { + sha1_process( ctx, input ); + input += 64; + ilen -= 64; + } + + if( ilen > 0 ) + { + memcpy( (void *) (ctx->buffer + left), + (void *) input, ilen ); + } +} + +static const unsigned char sha1_padding[64] = +{ + 0x80, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, + 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, + 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, + 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 +}; + +/* + * SHA-1 final digest + */ +void sha1_finish( sha1_context *ctx, unsigned char output[20] ) +{ + unsigned long last, padn; + unsigned long high, low; + unsigned char msglen[8]; + + high = ( ctx->total[0] >> 29 ) + | ( ctx->total[1] << 3 ); + low = ( ctx->total[0] << 3 ); + + PUT_UINT32_BE( high, msglen, 0 ); + PUT_UINT32_BE( low, msglen, 4 ); + + last = ctx->total[0] & 0x3F; + padn = ( last < 56 ) ? ( 56 - last ) : ( 120 - last ); + + sha1_update( ctx, (unsigned char *) sha1_padding, padn ); + sha1_update( ctx, msglen, 8 ); + + PUT_UINT32_BE( ctx->state[0], output, 0 ); + PUT_UINT32_BE( ctx->state[1], output, 4 ); + PUT_UINT32_BE( ctx->state[2], output, 8 ); + PUT_UINT32_BE( ctx->state[3], output, 12 ); + PUT_UINT32_BE( ctx->state[4], output, 16 ); +} + +/* + * Output = SHA-1( input buffer ) + */ +void sha1_csum( unsigned char *input, int ilen, + unsigned char output[20] ) +{ + sha1_context ctx; + + sha1_starts( &ctx ); + sha1_update( &ctx, input, ilen ); + sha1_finish( &ctx, output ); +} + +/* + * Output = HMAC-SHA-1( input buffer, hmac key ) + */ +void sha1_hmac( unsigned char *key, int keylen, + unsigned char *input, int ilen, + unsigned char output[20] ) +{ + int i; + sha1_context ctx; + unsigned char k_ipad[64]; + unsigned char k_opad[64]; + unsigned char tmpbuf[20]; + + memset( k_ipad, 0x36, 64 ); + memset( k_opad, 0x5C, 64 ); + + for( i = 0; i < keylen; i++ ) + { + if( i >= 64 ) break; + + k_ipad[i] ^= key[i]; + k_opad[i] ^= key[i]; + } + + sha1_starts( &ctx ); + sha1_update( &ctx, k_ipad, 64 ); + sha1_update( &ctx, input, ilen ); + sha1_finish( &ctx, tmpbuf ); + + sha1_starts( &ctx ); + sha1_update( &ctx, k_opad, 64 ); + sha1_update( &ctx, tmpbuf, 20 ); + sha1_finish( &ctx, output ); + + memset( k_ipad, 0, 64 ); + memset( k_opad, 0, 64 ); + memset( tmpbuf, 0, 20 ); + memset( &ctx, 0, sizeof( sha1_context ) ); +} + +static const char _sha1_src[] = "_sha1_src"; + +#ifdef SELF_TEST +/* + * FIPS-180-1 test vectors + */ +static const char sha1_test_str[3][57] = +{ + { "abc" }, + { "abcdbcdecdefdefgefghfghighijhijkijkljklmklmnlmnomnopnopq" }, + { "" } +}; + +static const unsigned char sha1_test_sum[3][20] = +{ + { 0xA9, 0x99, 0x3E, 0x36, 0x47, 0x06, 0x81, 0x6A, 0xBA, 0x3E, + 0x25, 0x71, 0x78, 0x50, 0xC2, 0x6C, 0x9C, 0xD0, 0xD8, 0x9D }, + { 0x84, 0x98, 0x3E, 0x44, 0x1C, 0x3B, 0xD2, 0x6E, 0xBA, 0xAE, + 0x4A, 0xA1, 0xF9, 0x51, 0x29, 0xE5, 0xE5, 0x46, 0x70, 0xF1 }, + { 0x34, 0xAA, 0x97, 0x3C, 0xD4, 0xC4, 0xDA, 0xA4, 0xF6, 0x1E, + 0xEB, 0x2B, 0xDB, 0xAD, 0x27, 0x31, 0x65, 0x34, 0x01, 0x6F } +}; + +/* + * Checkup routine + */ +int sha1_self_test( void ) +{ + int i, j; + unsigned char buf[1000]; + unsigned char sha1sum[20]; + sha1_context ctx; + + for( i = 0; i < 3; i++ ) + { + printf( " SHA-1 test #%d: ", i + 1 ); + + sha1_starts( &ctx ); + + if( i < 2 ) + sha1_update( &ctx, (unsigned char *) sha1_test_str[i], + strlen( sha1_test_str[i] ) ); + else + { + memset( buf, 'a', 1000 ); + for( j = 0; j < 1000; j++ ) + sha1_update( &ctx, buf, 1000 ); + } + + sha1_finish( &ctx, sha1sum ); + + if( memcmp( sha1sum, sha1_test_sum[i], 20 ) != 0 ) + { + printf( "failed\n" ); + return( 1 ); + } + + printf( "passed\n" ); + } + + printf( "\n" ); + return( 0 ); +} +#else +int sha1_self_test( void ) +{ + return( 0 ); +} +#endif diff --git a/lib_ppc/board.c b/lib_ppc/board.c index c4fc5805a..f5d18fa9f 100644 --- a/lib_ppc/board.c +++ b/lib_ppc/board.c @@ -896,7 +896,8 @@ void board_init_r (gd_t *id, ulong dest_addr) #if defined(CONFIG_TQM8xxL) || defined(CONFIG_TQM8260) || \ defined(CONFIG_TQM8272) || \ - defined(CONFIG_CCM) || defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X) + defined(CONFIG_CCM) || defined(CONFIG_KUP4K) || \ + defined(CONFIG_KUP4X) || defined(CONFIG_PCS440EP) load_sernum_ethaddr (); #endif /* IP Address */ @@ -961,7 +962,7 @@ void board_init_r (gd_t *id, ulong dest_addr) serial_buffered_init(); #endif -#ifdef CONFIG_STATUS_LED +#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT) status_led_set (STATUS_LED_BOOT, STATUS_LED_BLINKING); #endif diff --git a/net/eth.c b/net/eth.c index 0fc22115d..35e1ae958 100644 --- a/net/eth.c +++ b/net/eth.c @@ -28,6 +28,14 @@ #if (CONFIG_COMMANDS & CFG_CMD_NET) && defined(CONFIG_NET_MULTI) +#if defined(CONFIG_SHOW_BOOT_PROGRESS) +# include +extern void show_ethcfg_progress (int arg); +# define SHOW_BOOT_PROGRESS(arg) show_boot_progress (arg) +#else +# define SHOW_BOOT_PROGRESS(arg) +#endif + #ifdef CFG_GT_6426x extern int gt6426x_eth_initialize(bd_t *bis); #endif @@ -142,6 +150,7 @@ int eth_initialize(bd_t *bis) eth_devices = NULL; eth_current = NULL; + SHOW_BOOT_PROGRESS(64); #if defined(CONFIG_MII) || (CONFIG_COMMANDS & CFG_CMD_MII) miiphy_init(); #endif @@ -270,10 +279,12 @@ int eth_initialize(bd_t *bis) if (!eth_devices) { puts ("No ethernet found.\n"); + SHOW_BOOT_PROGRESS(-64); } else { struct eth_device *dev = eth_devices; char *ethprime = getenv ("ethprime"); + SHOW_BOOT_PROGRESS(65); do { if (eth_number) puts (", "); diff --git a/tools/Makefile b/tools/Makefile index 6177f9027..7980f6c26 100644 --- a/tools/Makefile +++ b/tools/Makefile @@ -21,10 +21,10 @@ # MA 02111-1307 USA # -BIN_FILES = img2srec$(SFX) mkimage$(SFX) envcrc$(SFX) gen_eth_addr$(SFX) bmp_logo$(SFX) +BIN_FILES = img2srec$(SFX) mkimage$(SFX) envcrc$(SFX) ubsha1$(SFX) gen_eth_addr$(SFX) bmp_logo$(SFX) -OBJ_LINKS = environment.o crc32.o -OBJ_FILES = img2srec.o mkimage.o envcrc.o gen_eth_addr.o bmp_logo.o +OBJ_LINKS = environment.o crc32.o sha1.o +OBJ_FILES = img2srec.o mkimage.o envcrc.o ubsha1.o gen_eth_addr.o bmp_logo.o ifeq ($(ARCH),mips) BIN_FILES += inca-swap-bytes$(SFX) @@ -126,14 +126,17 @@ MAKEDEPEND = makedepend all: $(obj).depend $(BINS) $(LOGO_H) subdirs -$(obj)envcrc$(SFX): $(obj)envcrc.o $(obj)crc32.o $(obj)environment.o +$(obj)envcrc$(SFX): $(obj)envcrc.o $(obj)crc32.o $(obj)environment.o $(obj)sha1.o + $(CC) $(CFLAGS) -o $@ $^ + +$(obj)ubsha1$(SFX): $(obj)ubsha1.o $(obj)sha1.o $(CC) $(CFLAGS) -o $@ $^ $(obj)img2srec$(SFX): $(obj)img2srec.o $(CC) $(CFLAGS) $(HOST_LDFLAGS) -o $@ $^ $(STRIP) $@ -$(obj)mkimage$(SFX): $(obj)mkimage.o $(obj)crc32.o +$(obj)mkimage$(SFX): $(obj)mkimage.o $(obj)crc32.o $(obj)sha1.o $(CC) $(CFLAGS) $(HOST_LDFLAGS) -o $@ $^ $(STRIP) $@ @@ -160,9 +163,15 @@ $(obj)mpc86x_clk$(SFX): $(obj)mpc86x_clk.o $(obj)envcrc.o: $(src)envcrc.c $(CC) -g $(CFLAGS) -c -o $@ $< +$(obj)ubsha1.o: $(src)ubsha1.c + $(CC) -g $(CFLAGS) -c -o $@ $< + $(obj)crc32.o: $(obj)crc32.c $(CC) -g $(CFLAGS) -c -o $@ $< +$(obj)sha1.o: $(obj)sha1.c + $(CC) -g $(CFLAGS) -c -o $@ $< + $(obj)mkimage.o: $(src)mkimage.c $(CC) -g $(CFLAGS) -c -o $@ $< @@ -203,6 +212,10 @@ $(obj)crc32.c: @rm -f $(obj)crc32.c ln -s $(src)../lib_generic/crc32.c $(obj)crc32.c +$(obj)sha1.c: + @rm -f $(obj)sha1.c + ln -s $(src)../lib_generic/sha1.c $(obj)sha1.c + $(LOGO_H): $(obj)bmp_logo $(LOGO_BMP) $(obj)./bmp_logo $(LOGO_BMP) >$@ diff --git a/tools/ubsha1.c b/tools/ubsha1.c new file mode 100644 index 000000000..bc877606d --- /dev/null +++ b/tools/ubsha1.c @@ -0,0 +1,119 @@ +/* + * (C) Copyright 2007 + * Heiko Schocher, DENX Software Engineering, + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include "sha1.h" + +#ifndef __ASSEMBLY__ +#define __ASSEMBLY__ /* Dirty trick to get only #defines */ +#endif +#include +#undef __ASSEMBLY__ + +#ifndef O_BINARY /* should be define'd on __WIN32__ */ +#define O_BINARY 0 +#endif + +#ifndef MAP_FAILED +#define MAP_FAILED (-1) +#endif + +extern int errno; + +extern void sha1_csum (unsigned char *input, int ilen, unsigned char output[20]); + +int main (int argc, char **argv) +{ + unsigned char output[20]; + int i, len; + + char *imagefile; + char *cmdname = *argv; + unsigned char *ptr; + unsigned char *data; + struct stat sbuf; + unsigned char *ptroff; + int ifd; + int off; + + if (argc > 1) { + imagefile = argv[1]; + ifd = open (imagefile, O_RDWR|O_BINARY); + if (ifd < 0) { + fprintf (stderr, "%s: Can't open %s: %s\n", + cmdname, imagefile, strerror(errno)); + exit (EXIT_FAILURE); + } + if (fstat (ifd, &sbuf) < 0) { + fprintf (stderr, "%s: Can't stat %s: %s\n", + cmdname, imagefile, strerror(errno)); + exit (EXIT_FAILURE); + } + len = sbuf.st_size; + ptr = (unsigned char *)mmap(0, len, + PROT_READ, MAP_SHARED, ifd, 0); + if (ptr == (unsigned char *)MAP_FAILED) { + fprintf (stderr, "%s: Can't read %s: %s\n", + cmdname, imagefile, strerror(errno)); + exit (EXIT_FAILURE); + } + + /* create a copy, so we can blank out the sha1 sum */ + data = malloc (len); + memcpy (data, ptr, len); + off = SHA1_SUM_POS; + ptroff = &data[len + off]; + for (i = 0; i < SHA1_SUM_LEN; i++) { + ptroff[i] = 0; + } + + sha1_csum ((unsigned char *) data, len, (unsigned char *)output); + + printf ("U-Boot sum:\n"); + for (i = 0; i < 20 ; i++) + { + printf ("%02X ", output[i]); + } + printf ("\n"); + /* overwrite the sum in the bin file, with the actual */ + lseek (ifd, SHA1_SUM_POS, SEEK_END); + if (write (ifd, output, SHA1_SUM_LEN) != SHA1_SUM_LEN) { + fprintf (stderr, "%s: Can't write %s: %s\n", + cmdname, imagefile, strerror(errno)); + exit (EXIT_FAILURE); + } + + free (data); + (void) munmap((void *)ptr, len); + (void) close (ifd); + } + + return EXIT_SUCCESS; +}