From ec081c2c190148b374e86a795fb6b1c49caeb549 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 17 Oct 2008 12:51:46 +0200 Subject: [PATCH 1/8] ppc4xx: PPC44x MQ initialization Set the MQ Read Passing & MCIF Cycle limits to the recommended by AMCC values. This fixes the occasional 440SPe hard locking issues when the 440SPe's dedicated DMA engines are used (e.g. by the h/w accelerated RAID driver). Previously the appropriate initialization had been made in Linux, by the ppc440spe ADMA driver, which is wrong because modifying the MQ configuration registers after normal operation has begun is not supported and could have unpredictable results. Comment from Stefan: This patch doesn't change the resulting value of the MQ registers. It explicitly sets/clears all bits to the desired state which better documents the resulting register value instead of relying on pre-set default values. Signed-off-by: Yuri Tikhonov Signed-off-by: Stefan Roese --- cpu/ppc4xx/44x_spd_ddr2.c | 10 ++++++---- include/asm-ppc/ppc4xx-sdram.h | 5 +++++ 2 files changed, 11 insertions(+), 4 deletions(-) diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c index f1d76840f..995d5fec7 100644 --- a/cpu/ppc4xx/44x_spd_ddr2.c +++ b/cpu/ppc4xx/44x_spd_ddr2.c @@ -2261,10 +2261,12 @@ static void program_memory_queue(unsigned long *dimm_populated, /* * Set optimal value for Memory Queue HB/LL Configuration registers */ - mtdcr(SDRAM_CONF1HB, mfdcr(SDRAM_CONF1HB) | SDRAM_CONF1HB_AAFR | - SDRAM_CONF1HB_RPEN | SDRAM_CONF1HB_RFTE); - mtdcr(SDRAM_CONF1LL, mfdcr(SDRAM_CONF1LL) | SDRAM_CONF1LL_AAFR | - SDRAM_CONF1LL_RPEN | SDRAM_CONF1LL_RFTE); + mtdcr(SDRAM_CONF1HB, (mfdcr(SDRAM_CONF1HB) & ~SDRAM_CONF1HB_MASK) | + SDRAM_CONF1HB_AAFR | SDRAM_CONF1HB_RPEN | SDRAM_CONF1HB_RFTE | + SDRAM_CONF1HB_RPLM | SDRAM_CONF1HB_WRCL); + mtdcr(SDRAM_CONF1LL, (mfdcr(SDRAM_CONF1LL) & ~SDRAM_CONF1LL_MASK) | + SDRAM_CONF1LL_AAFR | SDRAM_CONF1LL_RPEN | SDRAM_CONF1LL_RFTE | + SDRAM_CONF1LL_RPLM); mtdcr(SDRAM_CONFPATHB, mfdcr(SDRAM_CONFPATHB) | SDRAM_CONFPATHB_TPEN); #endif } diff --git a/include/asm-ppc/ppc4xx-sdram.h b/include/asm-ppc/ppc4xx-sdram.h index 8efa55797..98faced36 100644 --- a/include/asm-ppc/ppc4xx-sdram.h +++ b/include/asm-ppc/ppc4xx-sdram.h @@ -272,8 +272,11 @@ #define SDRAM_CONF1HB_PRPD 0x00080000 /* PLB Read pipeline Disable - Bit 12 */ #define SDRAM_CONF1HB_PWPD 0x00040000 /* PLB Write pipeline Disable - Bit 13 */ #define SDRAM_CONF1HB_PRW 0x00020000 /* PLB Read Wait - Bit 14 */ +#define SDRAM_CONF1HB_RPLM 0x00001000 /* Read Passing Limit 1 - Bits 16..19 */ #define SDRAM_CONF1HB_RPEN 0x00000800 /* Read Passing Enable - Bit 20 */ #define SDRAM_CONF1HB_RFTE 0x00000400 /* Read Flow Through Enable - Bit 21 */ +#define SDRAM_CONF1HB_WRCL 0x00000080 /* MCIF Cycle Limit 1 - Bits 22..24 */ +#define SDRAM_CONF1HB_MASK 0x0000F380 /* RPLM & WRCL mask */ #define SDRAM_ERRSTATHB (SDRAMQ_DCR_BASE+0x7) /* error status HB */ #define SDRAM_ERRADDUHB (SDRAMQ_DCR_BASE+0x8) /* error address upper 32 HB */ @@ -284,8 +287,10 @@ #define SDRAM_CONF1LL_PRPD 0x00080000 /* PLB Read pipeline Disable - Bit 12 */ #define SDRAM_CONF1LL_PWPD 0x00040000 /* PLB Write pipeline Disable - Bit 13 */ #define SDRAM_CONF1LL_PRW 0x00020000 /* PLB Read Wait - Bit 14 */ +#define SDRAM_CONF1LL_RPLM 0x00001000 /* Read Passing Limit 1 - Bits 16..19 */ #define SDRAM_CONF1LL_RPEN 0x00000800 /* Read Passing Enable - Bit 20 */ #define SDRAM_CONF1LL_RFTE 0x00000400 /* Read Flow Through Enable - Bit 21 */ +#define SDRAM_CONF1LL_MASK 0x0000F000 /* RPLM mask */ #define SDRAM_ERRSTATLL (SDRAMQ_DCR_BASE+0xC) /* error status LL */ #define SDRAM_ERRADDULL (SDRAMQ_DCR_BASE+0xD) /* error address upper 32 LL */ From f09f09d3899017aaaa2b031bba63c271e9c48e4d Mon Sep 17 00:00:00 2001 From: Adam Graham Date: Wed, 8 Oct 2008 10:12:53 -0700 Subject: [PATCH 2/8] ppc4xx: Add AMCC Arches board support (dual 460GT) The Arches Evaluation board is based on the AMCC 460GT SoC chip. This board is a dual processor board with each processor providing independent resources for Rapid IO, Gigabit Ethernet, and serial communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR FLASH, UART, EEPROM and temperature sensor, along with a shared debug port. The two 460GT's will communicate with each other via shared memory, Gigabit Ethernet and x1 PCI-Express. Signed-off-by: Adam Graham Signed-off-by: Victor Gallardo Signed-off-by: Stefan Roese --- MAKEALL | 1 + Makefile | 3 +- board/amcc/canyonlands/canyonlands.c | 140 +++++++++++++++++ board/amcc/canyonlands/init.S | 17 ++ include/configs/amcc-common.h | 17 +- include/configs/canyonlands.h | 226 ++++++++++++++++++++++++--- include/ppc440.h | 3 + 7 files changed, 386 insertions(+), 21 deletions(-) diff --git a/MAKEALL b/MAKEALL index 9ccb9ac99..847c1fa35 100755 --- a/MAKEALL +++ b/MAKEALL @@ -161,6 +161,7 @@ LIST_4xx=" \ alpr \ AP1000 \ AR405 \ + arches \ ASH405 \ bamboo \ bamboo_nand \ diff --git a/Makefile b/Makefile index 9a132f754..e83106156 100644 --- a/Makefile +++ b/Makefile @@ -1208,7 +1208,8 @@ bubinga_config: unconfig CANBT_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx canbt esd -# Canyonlands & Glacier use different U-Boot images +# Arches, Canyonlands & Glacier use different U-Boot images +arches_config \ canyonlands_config \ glacier_config: unconfig @mkdir -p $(obj)include diff --git a/board/amcc/canyonlands/canyonlands.c b/board/amcc/canyonlands/canyonlands.c index e9186f868..2b7468923 100644 --- a/board/amcc/canyonlands/canyonlands.c +++ b/board/amcc/canyonlands/canyonlands.c @@ -38,11 +38,52 @@ DECLARE_GLOBAL_DATA_PTR; #define BOARD_CANYONLANDS_PCIE 1 #define BOARD_CANYONLANDS_SATA 2 #define BOARD_GLACIER 3 +#define BOARD_ARCHES 4 + +#if defined(CONFIG_ARCHES) +/* + * FPGA read/write helper macros + */ +static inline int board_fpga_read(int offset) +{ + int data; + + data = in_8((void *)(CONFIG_SYS_FPGA_BASE + offset)); + + return data; +} + +static inline void board_fpga_write(int offset, int data) +{ + out_8((void *)(CONFIG_SYS_FPGA_BASE + offset), data); +} + +/* + * CPLD read/write helper macros + */ +static inline int board_cpld_read(int offset) +{ + int data; + + out_8((void *)(CONFIG_SYS_CPLD_ADDR), offset); + data = in_8((void *)(CONFIG_SYS_CPLD_DATA)); + + return data; +} + +static inline void board_cpld_write(int offset, int data) +{ + out_8((void *)(CONFIG_SYS_CPLD_ADDR), offset); + out_8((void *)(CONFIG_SYS_CPLD_DATA), data); +} +#endif /* defined(CONFIG_ARCHES) */ int board_early_init_f(void) { +#if !defined(CONFIG_ARCHES) u32 sdr0_cust0; u32 pvr = get_pvr(); +#endif /* * Setup the interrupt controller polarities, triggers, etc. @@ -79,6 +120,7 @@ int board_early_init_f(void) mtdcr(uic3vr, 0x00000000); /* int31 highest, base=0x000 */ mtdcr(uic3sr, 0xffffffff); /* clear all */ +#if !defined(CONFIG_ARCHES) /* SDR Setting - enable NDFC */ mfsdr(SDR0_CUST0, sdr0_cust0); sdr0_cust0 = SDR0_CUST0_MUX_NDFC_SEL | @@ -88,6 +130,7 @@ int board_early_init_f(void) SDR0_CUST0_NDFC_BAC_ENCODE(3) | (0x80000000 >> (28 + CONFIG_SYS_NAND_CS)); mtsdr(SDR0_CUST0, sdr0_cust0); +#endif /* * Configure PFC (Pin Function Control) registers @@ -98,6 +141,7 @@ int board_early_init_f(void) /* Enable PCI host functionality in SDR0_PCI0 */ mtsdr(SDR0_PCI0, 0xe0000000); +#if !defined(CONFIG_ARCHES) /* Enable ethernet and take out of reset */ out_8((void *)CONFIG_SYS_BCSR_BASE + 6, 0); @@ -123,10 +167,12 @@ int board_early_init_f(void) gpio_config(16, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1); gpio_config(19, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1); } +#endif return 0; } +#if !defined(CONFIG_ARCHES) static void canyonlands_sata_init(int board_type) { u32 reg; @@ -147,7 +193,26 @@ static void canyonlands_sata_init(int board_type) SDR_WRITE(SDR0_SRST1, 0x00000000); } } +#endif /* !defined(CONFIG_ARCHES) */ +int get_cpu_num(void) +{ + int cpu = NA_OR_UNKNOWN_CPU; + +#if defined(CONFIG_ARCHES) + int cpu_num; + + cpu_num = board_fpga_read(0x3); + + /* sanity check; assume cpu numbering starts and increments from 0 */ + if ((cpu_num >= 0) && (cpu_num < CONFIG_BD_NUM_CPUS)) + cpu = cpu_num; +#endif + + return cpu; +} + +#if !defined(CONFIG_ARCHES) int checkboard(void) { char *s = getenv("serial#"); @@ -188,6 +253,39 @@ int checkboard(void) return (0); } +#else /* defined(CONFIG_ARCHES) */ + +int checkboard(void) +{ + char *s = getenv("serial#"); + + printf("Board: Arches - AMCC DUAL PPC460GT Reference Design\n"); + printf(" Revision %02x.%02x ", + board_fpga_read(0x0), board_fpga_read(0x1)); + + gd->board_type = BOARD_ARCHES; + + /* Only CPU0 has access to CPLD registers */ + if (get_cpu_num() == 0) { + u8 cfg_sw = board_cpld_read(0x1); + printf("(FPGA=%02x, CPLD=%02x)\n", + board_fpga_read(0x2), board_cpld_read(0x0)); + printf(" Configuration Switch %d%d%d%d\n", + ((cfg_sw >> 3) & 0x01), + ((cfg_sw >> 2) & 0x01), + ((cfg_sw >> 1) & 0x01), + ((cfg_sw >> 0) & 0x01)); + } else + printf("(FPGA=%02x, CPLD=xx)\n", board_fpga_read(0x2)); + + + if (s != NULL) + printf(" Serial# %s\n", s); + + return 0; +} +#endif /* !defined(CONFIG_ARCHES) */ + /* * Override the default functions in cpu/ppc4xx/44x_spd_ddr2.c with * board specific values. @@ -389,6 +487,7 @@ int board_early_init_r (void) return 0; } +#if !defined(CONFIG_ARCHES) int misc_init_r(void) { u32 sdr0_srst1 = 0; @@ -434,6 +533,47 @@ int misc_init_r(void) return 0; } +#else /* defined(CONFIG_ARCHES) */ + +int misc_init_r(void) +{ + u32 eth_cfg = 0; + u32 eth_pll; + u32 reg; + + /* + * Set EMAC mode/configuration (GMII, SGMII, RGMII...). + * This is board specific, so let's do it here. + */ + + /* enable SGMII mode */ + eth_cfg |= (SDR0_ETH_CFG_SGMII0_ENABLE | + SDR0_ETH_CFG_SGMII1_ENABLE | + SDR0_ETH_CFG_SGMII2_ENABLE); + + /* Set EMAC for MDIO */ + eth_cfg |= SDR0_ETH_CFG_MDIO_SEL_EMAC0; + + /* bypass the TAHOE0/TAHOE1 cores for U-Boot */ + eth_cfg |= (SDR0_ETH_CFG_TAHOE0_BYPASS | SDR0_ETH_CFG_TAHOE1_BYPASS); + + mtsdr(SDR0_ETH_CFG, eth_cfg); + + /* reset all SGMII interfaces */ + mfsdr(SDR0_SRST1, reg); + reg |= (SDR0_SRST1_SGMII0 | SDR0_SRST1_SGMII1 | SDR0_SRST1_SGMII2); + mtsdr(SDR0_SRST1, reg); + mtsdr(SDR0_ETH_STS, 0xFFFFFFFF); + mtsdr(SDR0_SRST1, 0x00000000); + + do { + mfsdr(SDR0_ETH_PLL, eth_pll); + } while (!(eth_pll & SDR0_ETH_PLL_PLLLOCK)); + + return 0; +} +#endif /* !defined(CONFIG_ARCHES) */ + #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) void ft_board_setup(void *blob, bd_t *bd) { diff --git a/board/amcc/canyonlands/init.S b/board/amcc/canyonlands/init.S index 179dd324a..694cc8992 100644 --- a/board/amcc/canyonlands/init.S +++ b/board/amcc/canyonlands/init.S @@ -77,11 +77,16 @@ tlbtab: /* PCIe UTL register */ tlbentry(CONFIG_SYS_PCIE_BASE, SZ_16K, 0x08010000, 0xC, AC_R|AC_W|SA_G|SA_I) +#if !defined(CONFIG_ARCHES) /* TLB-entry for NAND */ tlbentry(CONFIG_SYS_NAND_ADDR, SZ_16M, CONFIG_SYS_NAND_ADDR, 4, AC_R|AC_W|AC_X|SA_G|SA_I) /* TLB-entry for CPLD */ tlbentry(CONFIG_SYS_BCSR_BASE, SZ_1K, CONFIG_SYS_BCSR_BASE, 4, AC_R|AC_W|SA_G|SA_I) +#else + /* TLB-entry for FPGA */ + tlbentry(CONFIG_SYS_FPGA_BASE, SZ_16M, CONFIG_SYS_FPGA_BASE, 4, AC_R|AC_W|SA_G|SA_I) +#endif /* TLB-entry for OCM */ tlbentry(CONFIG_SYS_OCM_BASE, SZ_16K, 0x00040000, 4, AC_R|AC_W|AC_X|SA_I) @@ -92,6 +97,18 @@ tlbtab: /* AHB: Internal USB Peripherals (USB, SATA) */ tlbentry(CONFIG_SYS_AHB_BASE, SZ_1M, 0xbff00000, 4, AC_R|AC_W|AC_X|SA_G|SA_I) +#if defined(CONFIG_RAPIDIO) + /* TLB-entries for RapidIO (SRIO) */ + tlbentry(CONFIG_SYS_SRGPL0_REG_BAR, SZ_16M, CONFIG_SYS_SRGPL0_REG_BAR, + 0xD, AC_R|AC_W|SA_G|SA_I) + tlbentry(CONFIG_SYS_SRGPL0_CFG_BAR, SZ_16M, CONFIG_SYS_SRGPL0_CFG_BAR, + 0xD, AC_R|AC_W|SA_G|SA_I) + tlbentry(CONFIG_SYS_SRGPL0_MNT_BAR, SZ_16M, CONFIG_SYS_SRGPL0_MNT_BAR, + 0xD, AC_R|AC_W|SA_G|SA_I) + tlbentry(CONFIG_SYS_I2ODMA_BASE, SZ_1K, 0x00100000, + 0x4, AC_R|AC_W|SA_G|SA_I) +#endif + tlbtab_end #if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) diff --git a/include/configs/amcc-common.h b/include/configs/amcc-common.h index fba96e18c..85165710b 100644 --- a/include/configs/amcc-common.h +++ b/include/configs/amcc-common.h @@ -159,6 +159,13 @@ #define CONFIG_USE_TTY ttyS0 #endif +/* + * Only very few boards have default netdev not set to eth0 (like Arches) + */ +#if !defined(CONFIG_USE_NETDEV) +#define CONFIG_USE_NETDEV eth0 +#endif + /* * Only some 4xx PPC's are equipped with an FPU */ @@ -184,7 +191,7 @@ * General common environment variables shared on all AMCC eval boards */ #define CONFIG_AMCC_DEF_ENV \ - "netdev=eth0\0" \ + "netdev=" xstr(CONFIG_USE_NETDEV) "\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ @@ -197,8 +204,10 @@ "initrd_high=30000000\0" \ "kernel_addr_r=400000\0" \ "fdt_addr_r=800000\0" \ + "ramdisk_addr_r=C00000\0" \ "hostname=" xstr(CONFIG_HOSTNAME) "\0" \ "bootfile=" xstr(CONFIG_HOSTNAME) "/uImage\0" \ + "ramdisk_file=" xstr(CONFIG_HOSTNAME) "/uRamdisk\0" \ CONFIG_AMCC_DEF_ENV_ROOTPATH /* @@ -214,6 +223,12 @@ "tftp ${fdt_addr_r} ${fdt_file}; " \ "run nfsargs addip addtty addmisc;" \ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "net_self_load=tftp ${kernel_addr_r} ${bootfile};" \ + "tftp ${fdt_addr_r} ${fdt_file};" \ + "tftp ${ramdisk_addr_r} ${ramdisk_file};\0" \ + "net_self=run net_self_load;" \ + "run ramargs addip addtty addmisc;" \ + "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0" \ "fdt_file=" xstr(CONFIG_HOSTNAME) "/" xstr(CONFIG_HOSTNAME) ".dtb\0" /* diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h index 771ee69ab..ec08ba7a2 100644 --- a/include/configs/canyonlands.h +++ b/include/configs/canyonlands.h @@ -27,14 +27,24 @@ /*----------------------------------------------------------------------- * High Level Configuration Options *----------------------------------------------------------------------*/ -/* This config file is used for Canyonlands (460EX) and Glacier (460GT) */ -#ifndef CONFIG_CANYONLANDS -#define CONFIG_460GT 1 /* Specific PPC460GT */ -#define CONFIG_HOSTNAME glacier -#else +/* + * This config file is used for Canyonlands (460EX) Glacier (460GT) + * and Arches dual (460GT) + */ +#ifdef CONFIG_CANYONLANDS #define CONFIG_460EX 1 /* Specific PPC460EX */ #define CONFIG_HOSTNAME canyonlands +#else +#define CONFIG_460GT 1 /* Specific PPC460GT */ +#ifdef CONFIG_GLACIER +#define CONFIG_HOSTNAME glacier +#else +#define CONFIG_HOSTNAME arches +#define CONFIG_USE_NETDEV eth1 +#define CONFIG_BD_NUM_CPUS 2 #endif +#endif + #define CONFIG_440 1 #define CONFIG_4xx 1 /* ... PPC4xx family */ @@ -73,15 +83,24 @@ #define CONFIG_SYS_PCIE_INBOUND_BASE 0x000000000ULL /* 36bit physical addr */ /* EBC stuff */ -#define CONFIG_SYS_NAND_ADDR 0xE0000000 +#if !defined(CONFIG_ARCHES) #define CONFIG_SYS_BCSR_BASE 0xE1000000 -#define CONFIG_SYS_BOOT_BASE_ADDR 0xFF000000 /* EBC Boot Space: 0xFF000000 */ -#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* later mapped to this addr */ +#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* later mapped to this addr */ +#define CONFIG_SYS_FLASH_SIZE (64 << 20) +#else +#define CONFIG_SYS_FPGA_BASE 0xE1000000 +#define CONFIG_SYS_CPLD_ADDR (CONFIG_SYS_FPGA_BASE + 0x00080000) +#define CONFIG_SYS_CPLD_DATA (CONFIG_SYS_FPGA_BASE + 0x00080002) +#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* later mapped to this addr */ +#define CONFIG_SYS_FLASH_SIZE (32 << 20) +#endif + +#define CONFIG_SYS_NAND_ADDR 0xE0000000 +#define CONFIG_SYS_BOOT_BASE_ADDR 0xFF000000 /* EBC Boot Space: 0xFF000000 */ #define CONFIG_SYS_FLASH_BASE_PHYS_H 0x4 #define CONFIG_SYS_FLASH_BASE_PHYS_L 0xCC000000 -#define CONFIG_SYS_FLASH_BASE_PHYS (((u64)CONFIG_SYS_FLASH_BASE_PHYS_H << 32) | \ - (u64)CONFIG_SYS_FLASH_BASE_PHYS_L) -#define CONFIG_SYS_FLASH_SIZE (64 << 20) +#define CONFIG_SYS_FLASH_BASE_PHYS (((u64)CONFIG_SYS_FLASH_BASE_PHYS_H << 32) | \ + (u64)CONFIG_SYS_FLASH_BASE_PHYS_L) #define CONFIG_SYS_OCM_BASE 0xE3000000 /* OCM: 16k */ #define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */ @@ -223,6 +242,7 @@ * DDR SDRAM *----------------------------------------------------------------------------*/ #if !defined(CONFIG_NAND_U_BOOT) +#if !defined(CONFIG_ARCHES) /* * NAND booting U-Boot version uses a fixed initialization, since the whole * I2C SPD DIMM autodetection/calibration doesn't fit into the 4k of boot @@ -232,7 +252,70 @@ #define SPD_EEPROM_ADDRESS {0x50, 0x51} /* SPD i2c spd addresses*/ #define CONFIG_DDR_ECC 1 /* with ECC support */ #define CONFIG_DDR_RQDC_FIXED 0x80000038 /* fixed value for RQDC */ -#endif + +#else /* defined(CONFIG_ARCHES) */ + +#define CONFIG_AUTOCALIB "silent\0" /* default is non-verbose */ + +#define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */ +#define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */ +#undef CONFIG_PPC4xx_DDR_METHOD_A + +/* DDR1/2 SDRAM Device Control Register Data Values */ +/* Memory Queue */ +#define CONFIG_SYS_SDRAM_R0BAS 0x0000f000 +#define CONFIG_SYS_SDRAM_R1BAS 0x00000000 +#define CONFIG_SYS_SDRAM_R2BAS 0x00000000 +#define CONFIG_SYS_SDRAM_R3BAS 0x00000000 +#define CONFIG_SYS_SDRAM_PLBADDULL 0x00000000 +#define CONFIG_SYS_SDRAM_PLBADDUHB 0x00000008 +#define CONFIG_SYS_SDRAM_CONF1LL 0x00001080 +#define CONFIG_SYS_SDRAM_CONF1HB 0x00001080 +#define CONFIG_SYS_SDRAM_CONFPATHB 0x10a68000 + +/* SDRAM Controller */ +#define CONFIG_SYS_SDRAM0_MB0CF 0x00000701 +#define CONFIG_SYS_SDRAM0_MB1CF 0x00000000 +#define CONFIG_SYS_SDRAM0_MB2CF 0x00000000 +#define CONFIG_SYS_SDRAM0_MB3CF 0x00000000 +#define CONFIG_SYS_SDRAM0_MCOPT1 0x05322000 +#define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000 +#define CONFIG_SYS_SDRAM0_MODT0 0x01000000 +#define CONFIG_SYS_SDRAM0_MODT1 0x00000000 +#define CONFIG_SYS_SDRAM0_MODT2 0x00000000 +#define CONFIG_SYS_SDRAM0_MODT3 0x00000000 +#define CONFIG_SYS_SDRAM0_CODT 0x00800021 +#define CONFIG_SYS_SDRAM0_RTR 0x06180000 +#define CONFIG_SYS_SDRAM0_INITPLR0 0xb5380000 +#define CONFIG_SYS_SDRAM0_INITPLR1 0x82100400 +#define CONFIG_SYS_SDRAM0_INITPLR2 0x80820000 +#define CONFIG_SYS_SDRAM0_INITPLR3 0x80830000 +#define CONFIG_SYS_SDRAM0_INITPLR4 0x80810040 +#define CONFIG_SYS_SDRAM0_INITPLR5 0x80800532 +#define CONFIG_SYS_SDRAM0_INITPLR6 0x82100400 +#define CONFIG_SYS_SDRAM0_INITPLR7 0x8a080000 +#define CONFIG_SYS_SDRAM0_INITPLR8 0x8a080000 +#define CONFIG_SYS_SDRAM0_INITPLR9 0x8a080000 +#define CONFIG_SYS_SDRAM0_INITPLR10 0x8a080000 +#define CONFIG_SYS_SDRAM0_INITPLR11 0x80000432 +#define CONFIG_SYS_SDRAM0_INITPLR12 0x808103c0 +#define CONFIG_SYS_SDRAM0_INITPLR13 0x80810040 +#define CONFIG_SYS_SDRAM0_INITPLR14 0x00000000 +#define CONFIG_SYS_SDRAM0_INITPLR15 0x00000000 +#define CONFIG_SYS_SDRAM0_RQDC 0x80000038 +#define CONFIG_SYS_SDRAM0_RFDC 0x00000257 +#define CONFIG_SYS_SDRAM0_RDCC 0x40000000 +#define CONFIG_SYS_SDRAM0_DLCR 0x03000091 +#define CONFIG_SYS_SDRAM0_CLKTR 0x40000000 +#define CONFIG_SYS_SDRAM0_WRDTR 0x82000823 +#define CONFIG_SYS_SDRAM0_SDTR1 0x80201000 +#define CONFIG_SYS_SDRAM0_SDTR2 0x42204243 +#define CONFIG_SYS_SDRAM0_SDTR3 0x090c0d1a +#define CONFIG_SYS_SDRAM0_MMODE 0x00000432 +#define CONFIG_SYS_SDRAM0_MEMODE 0x00000004 +#endif /* !defined(CONFIG_ARCHES) */ +#endif /* !defined(CONFIG_NAND_U_BOOT) */ + #define CONFIG_SYS_MBYTES_SDRAM 512 /* 512MB */ /*----------------------------------------------------------------------- @@ -254,18 +337,27 @@ #define CONFIG_SYS_DTT_LOW_TEMP -30 #define CONFIG_SYS_DTT_HYSTERESIS 3 +#if defined(CONFIG_ARCHES) +#define CONFIG_SYS_I2C_DTT_ADDR 0x4a /* AD7414 I2C address */ +#endif + +#if !defined(CONFIG_ARCHES) /* RTC configuration */ #define CONFIG_RTC_M41T62 1 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#endif /*----------------------------------------------------------------------- * Ethernet *----------------------------------------------------------------------*/ #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ -#define CONFIG_PHY1_ADDR 1 + #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 + +#if !defined(CONFIG_ARCHES) +#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ +#define CONFIG_PHY1_ADDR 1 /* Only Glacier (460GT) has 4 EMAC interfaces */ #ifdef CONFIG_460GT #define CONFIG_PHY2_ADDR 2 @@ -274,6 +366,30 @@ #define CONFIG_HAS_ETH3 #endif +#else /* defined(CONFIG_ARCHES) */ + +#define CONFIG_FIXED_PHY 0xFFFFFFFF +#define CONFIG_PHY_ADDR CONFIG_FIXED_PHY +#define CONFIG_PHY1_ADDR 0 +#define CONFIG_PHY2_ADDR 1 +#define CONFIG_HAS_ETH2 + +#define CONFIG_SYS_FIXED_PHY_PORT(devnum, speed, duplex) \ + {devnum, speed, duplex} +#define CONFIG_SYS_FIXED_PHY_PORTS \ + CONFIG_SYS_FIXED_PHY_PORT(0, 1000, FULL) + +#define CONFIG_M88E1112_PHY + +/* + * For the GPCS_PHYx_ADDR PHY address, choose some PHY address not + * used by CONFIG_PHYx_ADDR + */ +#define CONFIG_GPCS_PHY_ADDR 0xA +#define CONFIG_GPCS_PHY1_ADDR 0xB +#define CONFIG_GPCS_PHY2_ADDR 0xC +#endif /* !defined(CONFIG_ARCHES) */ + #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_PHY_DYNAMIC_ANEG 1 @@ -296,7 +412,8 @@ /* * Default environment variables */ -#define CONFIG_EXTRA_ENV_SETTINGS \ +#if !defined(CONFIG_ARCHES) +#define CONFIG_EXTRA_ENV_SETTINGS \ CONFIG_AMCC_DEF_ENV \ CONFIG_AMCC_DEF_ENV_POWERPC \ CONFIG_AMCC_DEF_ENV_NOR_UPD \ @@ -307,20 +424,46 @@ "pciconfighost=1\0" \ "pcie_mode=RP:RP\0" \ "" +#else /* defined(CONFIG_ARCHES) */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + "kernel_addr=fe000000\0" \ + "fdt_addr=fe1e0000\0" \ + "ramdisk_addr=fe200000\0" \ + "pciconfighost=1\0" \ + "pcie_mode=RP:RP\0" \ + "ethprime=ppc_4xx_eth1\0" \ + "" +#endif /* !defined(CONFIG_ARCHES) */ /* * Commands additional to the ones defined in amcc-common.h */ +#if defined(CONFIG_ARCHES) +#define CONFIG_CMD_DTT +#define CONFIG_CMD_PCI +#define CONFIG_CMD_SDRAM +#elif defined(CONFIG_CANYONLANDS) +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DTT +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_NAND +#define CONFIG_CMD_PCI +#define CONFIG_CMD_SDRAM +#define CONFIG_CMD_SNTP +#define CONFIG_CMD_USB +#elif defined(CONFIG_GLACIER) #define CONFIG_CMD_DATE #define CONFIG_CMD_DTT #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP -#ifdef CONFIG_460EX -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_USB +#else +#error "board type not defined" #endif /* Partitions */ @@ -344,6 +487,36 @@ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ +#ifdef CONFIG_460GT +#if defined(CONFIG_ARCHES) +/*----------------------------------------------------------------------- + * RapidIO I/O and Registers + *----------------------------------------------------------------------*/ +#define CONFIG_RAPIDIO +#define CONFIG_SYS_460GT_SRIO_ERRATA_1 + +#define SRGPL0_REG_BAR 0x0000000DAA000000ull /* 16MB */ +#define SRGPL0_CFG_BAR 0x0000000DAB000000ull /* 16MB */ +#define SRGPL0_MNT_BAR 0x0000000DAC000000ull /* 16MB */ +#define SRGPL0_MSG_BAR 0x0000000DAD000000ull /* 16MB */ +#define SRGPL0_OUT_BAR 0x0000000DB0000000ull /* 256MB */ + +#define CONFIG_SYS_SRGPL0_REG_BAR 0xAA000000 /* 16MB */ +#define CONFIG_SYS_SRGPL0_CFG_BAR 0xAB000000 /* 16MB */ +#define CONFIG_SYS_SRGPL0_MNT_BAR 0xAC000000 /* 16MB */ +#define CONFIG_SYS_SRGPL0_MSG_BAR 0xAD000000 /* 16MB */ + +#define CONFIG_SYS_I2ODMA_BASE 0xCF000000 +#define CONFIG_SYS_I2ODMA_PHYS_ADDR 0x0000000400100000ull + +#define CONFIG_PPC4XX_RAPIDIO_PROMISCUOUS_MODE +#undef CONFIG_PPC4XX_RAPIDIO_DEBUG +#undef CONFIG_PPC4XX_RAPIDIO_IN_BAR_USE_OCM +#define CONFIG_PPC4XX_RAPIDIO_USE_HB_PLB +#undef CONFIG_PPC4XX_RAPIDIO_LOOPBACK +#endif /* CONFIG_ARCHES */ +#endif /* CONFIG_460GT */ + /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ @@ -356,6 +529,11 @@ * EBC address which accepts bigger regions: * * 0xfc00.0000 -> 4.cc00.0000 + * + * Arches has 32MBytes of NOR FLASH (Spansion 29GL256), it will be + * remapped to: + * + * 0xfe00.0000 -> 4.ce00.0000 */ #if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) @@ -371,15 +549,25 @@ #define CONFIG_SYS_EBC_PB0AP 0x10055e00 #define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000) +#if !defined(CONFIG_ARCHES) /* Memory Bank 3 (NAND-FLASH) initialization */ #define CONFIG_SYS_EBC_PB3AP 0x018003c0 #define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/ #endif +#endif /*defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) */ +#if !defined(CONFIG_ARCHES) /* Memory Bank 2 (CPLD) initialization */ #define CONFIG_SYS_EBC_PB2AP 0x00804240 #define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_BCSR_BASE | 0x18000) /* BAS=CPLD,BS=1M,BU=RW,BW=32bit */ +#else /* defined(CONFIG_ARCHES) */ + +/* Memory Bank 1 (FPGA) initialization */ +#define CONFIG_SYS_EBC_PB1AP 0x7f8ffe80 +#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_FPGA_BASE | 0x3a000) /* BAS=FPGA,BS=2MB,BU=R/W,BW=16bit*/ +#endif /* !defined(CONFIG_ARCHES) */ + #define CONFIG_SYS_EBC_CFG 0xB8400000 /* EBC0_CFG */ /* diff --git a/include/ppc440.h b/include/ppc440.h index 664f8021f..ea0ac86d0 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -1349,6 +1349,9 @@ #define SDR0_ETH_CFG_ZMII_RMII_MODE_10M 0x10 #define SDR0_ETH_CFG_ZMII_RMII_MODE_100M 0x11 +/* Ethernet Status Register */ +#define SDR0_ETH_STS 0x4104 + /* Miscealleneaous Function Reg. (SDR0_MFR) */ #define SDR0_MFR 0x4300 #define SDR0_MFR_T0TxFL 0x00800000 /* force parity error TAHOE0 Tx FIFO bits 0:63 */ From 59217bae40e90982ab5400d849c08af683ace036 Mon Sep 17 00:00:00 2001 From: Adam Graham Date: Wed, 8 Oct 2008 10:13:14 -0700 Subject: [PATCH 3/8] ppc4xx: Add static support for 44x IBM SDRAM Controller This patch add the capability to configure a PPC440 based IBM SDRAM Controller with static, compiled-in, values. PPC440 memory subsystem includes a Memory Queue core. Signed-off-by: Adam Graham Signed-off-by: Victor Gallardo Signed-off-by: Stefan Roese --- cpu/ppc4xx/44x_spd_ddr2.c | 71 +++++++++++++++++++++++++++++---------- 1 file changed, 53 insertions(+), 18 deletions(-) diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c index 4544b78ac..b40e4b151 100644 --- a/cpu/ppc4xx/44x_spd_ddr2.c +++ b/cpu/ppc4xx/44x_spd_ddr2.c @@ -60,6 +60,26 @@ "SDRAM_" #mnemonic, SDRAM_##mnemonic, data); \ } while (0) +#if defined(CONFIG_440) +/* + * This DDR2 setup code can dynamically setup the TLB entries for the DDR2 + * memory region. Right now the cache should still be disabled in U-Boot + * because of the EMAC driver, that need its buffer descriptor to be located + * in non cached memory. + * + * If at some time this restriction doesn't apply anymore, just define + * CONFIG_4xx_DCACHE in the board config file and this code should setup + * everything correctly. + */ +#ifdef CONFIG_4xx_DCACHE +/* enable caching on SDRAM */ +#define MY_TLB_WORD2_I_ENABLE 0 +#else +/* disable caching on SDRAM */ +#define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE +#endif /* CONFIG_4xx_DCACHE */ +#endif /* CONFIG_440 */ + #if defined(CONFIG_SPD_EEPROM) /*-----------------------------------------------------------------------------+ @@ -130,22 +150,6 @@ #define NUMMEMWORDS 8 #define NUMLOOPS 64 /* memory test loops */ -/* - * This DDR2 setup code can dynamically setup the TLB entries for the DDR2 memory - * region. Right now the cache should still be disabled in U-Boot because of the - * EMAC driver, that need it's buffer descriptor to be located in non cached - * memory. - * - * If at some time this restriction doesn't apply anymore, just define - * CONFIG_4xx_DCACHE in the board config file and this code should setup - * everything correctly. - */ -#ifdef CONFIG_4xx_DCACHE -#define MY_TLB_WORD2_I_ENABLE 0 /* enable caching on SDRAM */ -#else -#define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE /* disable caching on SDRAM */ -#endif - /* * Newer PPC's like 440SPe, 460EX/GT can be equipped with more than 2GB of SDRAM. * To support such configurations, we "only" map the first 2GB via the TLB's. We @@ -2958,9 +2962,10 @@ static void test(void) /*----------------------------------------------------------------------------- * Function: initdram - * Description: Configures the PPC405EX(r) DDR1/DDR2 SDRAM memory - * banks. The configuration is performed using static, compile- + * Description: Configures the PPC4xx IBM DDR1/DDR2 SDRAM memory controller. + * The configuration is performed using static, compile- * time parameters. + * Configures the PPC405EX(r) and PPC460EX/GT *---------------------------------------------------------------------------*/ phys_size_t initdram(int board_type) { @@ -2976,6 +2981,18 @@ phys_size_t initdram(int board_type) #if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) unsigned long val; +#if defined(CONFIG_440) + mtdcr(SDRAM_R0BAS, CONFIG_SYS_SDRAM_R0BAS); + mtdcr(SDRAM_R1BAS, CONFIG_SYS_SDRAM_R1BAS); + mtdcr(SDRAM_R2BAS, CONFIG_SYS_SDRAM_R2BAS); + mtdcr(SDRAM_R3BAS, CONFIG_SYS_SDRAM_R3BAS); + mtdcr(SDRAM_PLBADDULL, CONFIG_SYS_SDRAM_PLBADDULL); /* MQ0_BAUL */ + mtdcr(SDRAM_PLBADDUHB, CONFIG_SYS_SDRAM_PLBADDUHB); /* MQ0_BAUH */ + mtdcr(SDRAM_CONF1LL, CONFIG_SYS_SDRAM_CONF1LL); + mtdcr(SDRAM_CONF1HB, CONFIG_SYS_SDRAM_CONF1HB); + mtdcr(SDRAM_CONFPATHB, CONFIG_SYS_SDRAM_CONFPATHB); +#endif + /* Set Memory Bank Configuration Registers */ mtsdram(SDRAM_MB0CF, CONFIG_SYS_SDRAM0_MB0CF); @@ -3069,6 +3086,14 @@ phys_size_t initdram(int board_type) mfsdram(SDRAM_MCOPT2, val); mtsdram(SDRAM_MCOPT2, val | SDRAM_MCOPT2_DCEN_ENABLE); +#if defined(CONFIG_440) + /* + * Program TLB entries with caches enabled, for best performace + * while auto-calibrating and ECC generation + */ + program_tlb(0, 0, (CONFIG_SYS_MBYTES_SDRAM << 20), 0); +#endif + #if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) /*------------------------------------------------------------------ @@ -3082,6 +3107,16 @@ phys_size_t initdram(int board_type) ecc_init(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MBYTES_SDRAM << 20); #endif /* defined(CONFIG_DDR_ECC) */ +#if defined(CONFIG_440) + /* + * Now after initialization (auto-calibration and ECC generation) + * remove the TLB entries with caches enabled and program again with + * desired cache functionality + */ + remove_tlb(0, (CONFIG_SYS_MBYTES_SDRAM << 20)); + program_tlb(0, 0, (CONFIG_SYS_MBYTES_SDRAM << 20), MY_TLB_WORD2_I_ENABLE); +#endif + ppc4xx_ibm_ddr2_register_dump(); #if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) From c9c11d751e4242cf29c3c3c290d971f6d0cb1d15 Mon Sep 17 00:00:00 2001 From: Adam Graham Date: Wed, 8 Oct 2008 10:13:19 -0700 Subject: [PATCH 4/8] ppc4xx: Add routine to retrieve CPU number Provide a weak defined routine to retrieve the CPU number for reference boards that have multiple CPU's. Default behavior is the existing single CPU print output. Reference boards with multiple CPU's need to provide a board specific routine. See board/amcc/arches/arches.c for an example. Signed-off-by: Adam Graham Signed-off-by: Victor Gallardo Signed-off-by: Stefan Roese --- cpu/ppc4xx/cpu.c | 19 ++++++++++++++++++- include/ppc4xx.h | 3 +++ 2 files changed, 21 insertions(+), 1 deletion(-) diff --git a/cpu/ppc4xx/cpu.c b/cpu/ppc4xx/cpu.c index 66a77370c..a676b30ef 100644 --- a/cpu/ppc4xx/cpu.c +++ b/cpu/ppc4xx/cpu.c @@ -41,6 +41,18 @@ DECLARE_GLOBAL_DATA_PTR; void board_reset(void); +/* + * To provide an interface to detect CPU number for boards that support + * more then one CPU, we implement the "weak" default functions here. + * + * Returns CPU number + */ +int __get_cpu_num(void) +{ + return NA_OR_UNKNOWN_CPU; +} +int get_cpu_num(void) __attribute__((weak, alias("__get_cpu_num"))); + #if defined(CONFIG_405GP) || \ defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) @@ -274,8 +286,13 @@ int checkcpu (void) #if !defined(CONFIG_IOP480) char addstr[64] = ""; sys_info_t sys_info; + int cpu_num; - puts ("CPU: "); + cpu_num = get_cpu_num(); + if (cpu_num >= 0) + printf("CPU%d: ", cpu_num); + else + puts("CPU: "); get_sys_info(&sys_info); diff --git a/include/ppc4xx.h b/include/ppc4xx.h index ce4b29a19..f1478854d 100644 --- a/include/ppc4xx.h +++ b/include/ppc4xx.h @@ -218,4 +218,7 @@ static inline void set_mcsr(u32 val) #endif /* __ASSEMBLY__ */ +/* for multi-cpu support */ +#define NA_OR_UNKNOWN_CPU -1 + #endif /* __PPC4XX_H__ */ From c11da194545d2f4bbb54be1bb5e504e20ce8c16c Mon Sep 17 00:00:00 2001 From: Niklaus Giger Date: Wed, 1 Oct 2008 14:46:13 +0200 Subject: [PATCH 5/8] ppc4xx: Update configs for Netstal boards I reorganized my config files, putting the common stuff into netstal-common.h (got the idea by looking a amcc-common.h from Stefan). Added stuff to boot the new powerpc linux via NFS (only tested with HCU4). Signed-off-by: Niklaus Giger Signed-off-by: Stefan Roese --- include/configs/hcu4.h | 100 ++---------- include/configs/hcu5.h | 118 ++------------ include/configs/mcu25.h | 92 ++--------- include/configs/netstal-common.h | 255 +++++++++++++++++++++++++++++++ 4 files changed, 291 insertions(+), 274 deletions(-) create mode 100644 include/configs/netstal-common.h diff --git a/include/configs/hcu4.h b/include/configs/hcu4.h index 9b03ac2f4..369b36894 100644 --- a/include/configs/hcu4.h +++ b/include/configs/hcu4.h @@ -35,6 +35,12 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_405GP 1 #define CONFIG_4xx 1 +#define CONFIG_HOSTNAME hcu4 + +/* + * Include common defines/options for all boards produced by Netstal Maschinen + */ +#include "netstal-common.h" #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ @@ -80,25 +86,12 @@ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, * set Linux BASE_BAUD to 403200. */ -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#define CONFIG_SERIAL_MULTI 1 -/* needed to be able to define CONFIG_SERIAL_SOFTWARE_FIFO */ #undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CONFIG_SYS_BASE_BAUD 691200 -/* Size (bytes) of interrupt driven serial port buffer. - * Set to 0 to use polling instead of interrupts. - * Setting to 0 will also disable RTS/CTS handshaking. - */ -#undef CONFIG_SERIAL_SOFTWARE_FIFO - /* Set console baudrate to 9600 */ #define CONFIG_BAUDRATE 9600 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Flash *----------------------------------------------------------------------*/ @@ -149,74 +142,12 @@ *----------------------------------------------------------------------*/ #define CONFIG_SYS_SPD_BUS_NUM 0 -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_IPADDR 172.25.1.14 -/* This is the 7bit address of the device, not including P. */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#undef CONFIG_SYS_I2C_MULTI_EEPROMS - - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -/* Setup some board specific values for the default environment variables */ -#define CONFIG_HOSTNAME hcu4 -#define CONFIG_IPADDR 172.25.1.99 -#define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */ -#define CONFIG_OVERWRITE_ETHADDR_ONCE -#define CONFIG_SERVERIP 172.25.1.3 - -#define CONFIG_SYS_TFTP_LOADADDR 0x01000000 /* @16 MB */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "loadaddr=0x01000000\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/home/diagnose/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/hcu4/uImage\0" \ - "load=tftp 100000 hcu4/u-boot.bin\0" \ - "update=protect off FFFB0000 FFFFFFFF;era FFFB0000 FFFFFFFF;" \ - "cp.b 100000 FFFB0000 50000\0" \ - "upd=run load update\0" \ - "vx_rom=hcu4/hcu4_vx_rom\0" \ - "vx=tftp ${loadaddr} ${vx_rom};run vxargs; bootvx\0" \ - "vxargs=setenv bootargs emac(0,0)c:${vx_rom} e=${ipaddr}" \ - " h=${serverip} u=dpu pw=netstal8752 tn=hcu5 f=0x3008\0" \ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_NETSTAL_DEF_ENV \ + CONFIG_NETSTAL_DEF_ENV_POWERPC \ "" -#define CONFIG_BOOTCOMMAND "run vx" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 1 /* PHY address */ - -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ - -#define CONFIG_HAS_ETH0 -#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & desC */ /* * BOOTP options @@ -285,13 +216,6 @@ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup @@ -348,8 +272,4 @@ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/hcu5.h b/include/configs/hcu5.h index 1ba46eb96..26d2d0c9d 100644 --- a/include/configs/hcu5.h +++ b/include/configs/hcu5.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2007 Netstal Maschinen AG + * (C) Copyright 2007-2008 Netstal Maschinen AG * Niklaus Giger (Niklaus.Giger@netstal.com) * * (C) Copyright 2006-2007 @@ -39,8 +39,14 @@ #define CONFIG_440EPX 1 /* Specific PPC440EPx */ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ -#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +#define CONFIG_HOSTNAME hcu5 +/* + * Include common defines/options for all boards produced by Netstal Maschinen + */ +#include "netstal-common.h" + +#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ @@ -86,22 +92,10 @@ * Serial Port *----------------------------------------------------------------------*/ #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#define CONFIG_BAUDRATE 9600 -#define CONFIG_SERIAL_MULTI 1 -/* needed to be able to define - CONFIG_SERIAL_SOFTWARE_FIFO, but - CONFIG_SERIAL_SOFTWARE_FIFO (16) does not work */ -/* Size (bytes) of interrupt driven serial port buffer. - * Set to 0 to use polling instead of interrupts. - * Setting to 0 will also disable RTS/CTS handshaking. - */ +#define CONFIG_BAUDRATE 115200 #undef CONFIG_SERIAL_SOFTWARE_FIFO #undef CONFIG_UART1_CONSOLE -#undef CONFIG_CMD_HWFLOW -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -144,93 +138,26 @@ #define PM_RESERVED_MEM ( 64) /* in kB: pmLib reserved area size */ #define CONFIG_PRAM ( USER_RESERVED_MEM + PM_RESERVED_MEM ) +#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ + /* 440EPx errata CHIP 11 */ + /*----------------------------------------------------------------------- * I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the * the second internal I2C controller of the PPC440EPx *----------------------------------------------------------------------*/ #define CONFIG_SYS_SPD_BUS_NUM 1 -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* This is the 7bit address of the device, not including P. */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#undef CONFIG_SYS_I2C_MULTI_EEPROMS - - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run nfs\" to mount Linux root filesystem over NFS;"\ - "echo" - -#undef CONFIG_BOOTARGS - /* Setup some board specific values for the default environment variables */ -#define CONFIG_HOSTNAME hcu5 -#define CONFIG_IPADDR 172.25.1.99 -#define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */ -#define CONFIG_OVERWRITE_ETHADDR_ONCE -#define CONFIG_SERVERIP 172.25.1.3 - -#define CONFIG_SYS_TFTP_LOADADDR 0x01000000 /* @16 MB */ +#define CONFIG_IPADDR 172.25.1.15 #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "loadaddr=0x01000000\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "bootfile=hcu5/uImage\0" \ - "rootpath=/home/hcu/eldk/ppc_4xxFP\0" \ - "load=tftp 100000 hcu5/u-boot.bin\0" \ - "update=protect off FFFB0000 FFFFFFFF;era FFFB0000 FFFFFFFF;" \ - "cp.b 100000 FFFB0000 50000\0" \ - "upd=run load update\0" \ - "vx_rom=hcu5/hcu5_vx_rom\0" \ - "vx=tftp ${loadaddr} ${vx_rom};run vxargs; bootvx\0" \ - "vxargs=setenv bootargs emac(0,0)c:${vx_rom} e=${ipaddr}" \ - " h=${serverip} u=dpu pw=netstal8752 tn=hcu5 f=0x3008\0" \ - "usbargs=setenv bootargs root=/dev/sda1 ro\0" \ - "linux=usb start; ext2load usb 0 ${loadaddr} /boot/uImage;" \ - "run usbargs addip addtty; bootm\0" \ - "net_nfs_fdt=tftp 200000 ${bootfile};" \ - "tftp ${fdt_addr} ${fdt_file};" \ - "run nfsargs addip addtty;" \ - "bootm 200000 - ${fdt_addr}\0" \ - "fdt_file=hcu5/hcu5.dtb\0" \ - "fdt_addr=400000\0" \ + CONFIG_NETSTAL_DEF_ENV \ + CONFIG_NETSTAL_DEF_ENV_POWERPC \ "" -#define CONFIG_BOOTCOMMAND "run vx" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_M88E1111_PHY 1 #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 1 /* PHY address, like on HCU4 */ -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ - -#define CONFIG_HAS_ETH0 -#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & desc. */ - -#define CONFIG_NET_MULTI 1 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY1_ADDR 2 @@ -279,7 +206,6 @@ /* POST support */ #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ CONFIG_SYS_POST_UART | \ CONFIG_SYS_POST_I2C | \ CONFIG_SYS_POST_CACHE | \ @@ -309,17 +235,9 @@ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ /*----------------------------------------------------------------------- * PCI stuff @@ -409,8 +327,4 @@ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/mcu25.h b/include/configs/mcu25.h index e4489696b..5f3119883 100644 --- a/include/configs/mcu25.h +++ b/include/configs/mcu25.h @@ -35,6 +35,12 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_405GP 1 #define CONFIG_4xx 1 +#define CONFIG_HOSTNAME mcu25 + +/* + * Include common defines/options for all boards produced by Netstal Maschinen + */ +#include "netstal-common.h" #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ @@ -80,8 +86,6 @@ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, * set Linux BASE_BAUD to 403200. */ -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#define CONFIG_SERIAL_MULTI 1 /* needed to be able to define CONFIG_SERIAL_SOFTWARE_FIFO */ #undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CONFIG_SYS_BASE_BAUD 691200 @@ -95,10 +99,6 @@ /* Set console baudrate to 9600 */ #define CONFIG_BAUDRATE 9600 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Flash *----------------------------------------------------------------------*/ @@ -149,74 +149,13 @@ *----------------------------------------------------------------------*/ #define CONFIG_SYS_SPD_BUS_NUM 0 -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* This is the 7bit address of the device, not including P. */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#undef CONFIG_SYS_I2C_MULTI_EEPROMS - - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - /* Setup some board specific values for the default environment variables */ -#define CONFIG_HOSTNAME mcu25 -#define CONFIG_IPADDR 172.25.1.99 -#define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */ -#define CONFIG_OVERWRITE_ETHADDR_ONCE -#define CONFIG_SERVERIP 172.25.1.3 +#define CONFIG_IPADDR 172.25.1.25 -#define CONFIG_SYS_TFTP_LOADADDR 0x01000000 /* @16 MB */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "loadaddr=0x01000000\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/home/diagnose/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/mcu25/uImage\0" \ - "load=tftp 100000 mcu25/u-boot.bin\0" \ - "update=protect off FFFB0000 FFFFFFFF;era FFFB0000 FFFFFFFF;" \ - "cp.b 100000 FFFB0000 50000\0" \ - "upd=run load;run update\0" \ - "vx_rom=mcu25/mcu25_vx_rom\0" \ - "vx=tftp ${loadaddr} ${vx_rom};run vxargs; bootvx\0" \ - "vxargs=setenv bootargs emac(0,0)c:${vx_rom} e=${ipaddr}" \ - " h=${serverip} u=dpu pw=netstal8752 tn=hcu5 f=0x3008\0" \ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_NETSTAL_DEF_ENV \ + CONFIG_NETSTAL_DEF_ENV_POWERPC \ "" -#define CONFIG_BOOTCOMMAND "run vx" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 1 /* PHY address */ - -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ - -#define CONFIG_HAS_ETH0 -#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descr */ /* * BOOTP options @@ -285,13 +224,6 @@ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup @@ -353,8 +285,4 @@ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/netstal-common.h b/include/configs/netstal-common.h new file mode 100644 index 000000000..1fa4b00eb --- /dev/null +++ b/include/configs/netstal-common.h @@ -0,0 +1,255 @@ +/* + * (C) Copyright 2008 + * Niklaus Giger, Netstal Maschinen AG, niklaus.giger@netstal.com + * adapted from amcc-common.h by + * (C) Copyright 2008 + * * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * Common configuration options for all Netstal boards + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __NETSTAL_COMMON_H +#define __NETSTAL_COMMON_H + +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* Start of U-Boot */ +#define CONFIG_SYS_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ + +/* + * UART + */ +#define CONFIG_SERIAL_MULTI +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} + +/* + * I2C + */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +/* This is the 7bit address of the device, not including P. */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 + +/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE + +/* + * Ethernet/EMAC/PHY + */ +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_PHY_ADDR 1 /* PHY address */ +#if defined(CONFIG_440) +#define CONFIG_NET_MULTI 1 +#define CONFIG_NETCONSOLE /* include NetConsole support */ +#define CONFIG_SYS_RX_ETH_BUFFER 32 /* number of eth rx buffers */ +#else +#define CONFIG_SYS_RX_ETH_BUFFER 16 /* number of eth rx buffers */ +#endif +#define CONFIG_HAS_ETH0 + +/* + * Commands + */ +#include + +#define CONFIG_CMD_ASKENV +#if defined(CONFIG_440) +#define CONFIG_CMD_CACHE +#endif +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_BOOT_RETRY_TIME 30 +#define CONFIG_RESET_TO_RETRY +/* + * Miscellaneous configurable options + */ +#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO /* To use extended board_into (bd_t) */ + +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_CMDLINE_EDITING /* add command line history */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_LOOPW /* enable loopw command */ +#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE /* include version env variable */ +#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup*/ + +#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */ +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#endif + +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_SUBNETMASK + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Internal Definitions + */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP + +/* + * Booting and default environment + */ +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run net_nfs\" to mount root filesystem over NFS;" \ + "echo" +#define CONFIG_BOOTCOMMAND "run vx" + +/* + * Only very few boards have default console not on ttyS0 (like Taishan) + */ +#if !defined(CONFIG_USE_TTY) +#define CONFIG_USE_TTY ttyS0 +#endif + +/* + * Only some 4xx PPC's are equipped with an FPU + */ +#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \ + defined(CONFIG_460EX) || defined(CONFIG_460GT) +#define CONFIG_NETSTAL_DEF_ENV_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" +#else +#define CONFIG_NETSTAL_DEF_ENV_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" +#endif + +/* + * Only some boards need to extend the bootargs by some additional + * parameters (like Makalu) + */ +#if !defined(CONFIG_ADDMISC) +#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs}\0" +#endif + +#define xstr(s) str(s) +#define str(s) #s + +/* Setup some values for the default environment variables */ +#define CONFIG_SERVERIP 172.25.1.1 +#define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */ +#define CONFIG_OVERWRITE_ETHADDR_ONCE + +#define CONFIG_SYS_TFTP_LOADADDR 0x01000000 + +/* + * General common environment variables shared by all boards produced by Netstal Maschinen + */ +#define CONFIG_NETSTAL_DEF_ENV \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs}" \ + " console=" xstr(CONFIG_USE_TTY) ",${baudrate}\0" \ + CONFIG_ADDMISC \ + "initrd_high=30000000\0" \ + "kernel_addr_r=400000\0" \ + "fdt_addr_r=800000\0" \ + "hostname=" xstr(CONFIG_HOSTNAME) "\0" \ + "bootfile=" xstr(CONFIG_HOSTNAME) "/uImage\0" \ + "load=tftp 200000 " xstr(CONFIG_HOSTNAME) "/u-boot.bin\0" \ + "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) " FFFFFFFF;" \ + "era " xstr(CONFIG_SYS_MONITOR_BASE) " FFFFFFFF;" \ + "cp.b ${fileaddr} " xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize};" \ + "setenv filesize\0" \ + "upd=run load update\0" \ + "vx_rom=" xstr(CONFIG_HOSTNAME) "/" \ + xstr(CONFIG_HOSTNAME) "_vx_rom\0" \ + "vx=tftp " xstr(CONFIG_SYS_TFTP_LOADADDR) " ${vx_rom};run vxargs;" \ + "bootvx\0" \ + "vxargs=setenv bootargs emac(0,0)c:${vx_rom} e=${ipaddr}" \ + " h=${serverip} u=dpu pw=netstal8752 " \ + "tn=" xstr(CONFIG_HOSTNAME) " f=0x3008\0" \ + CONFIG_NETSTAL_DEF_ENV_ROOTPATH + +/* + * Default environment for arch/powerpc booting + * for boards that are ported to arch/powerpc + */ +#define CONFIG_NETSTAL_DEF_ENV_POWERPC \ + "flash_self=run ramargs addip addtty addmisc;" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "flash_nfs=run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ + "tftp ${fdt_addr_r} ${fdt_file}; " \ + "run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "fdt_file=" xstr(CONFIG_HOSTNAME) "/" xstr(CONFIG_HOSTNAME) ".dtb\0" + +#endif /* __NETSTAL_COMMON_H */ From d7b26d58328f137471ea97de382bfa63f7239931 Mon Sep 17 00:00:00 2001 From: Dirk Eibach Date: Wed, 8 Oct 2008 15:37:50 +0200 Subject: [PATCH 6/8] ppc4xx: Add GDSys neo 405EP board support Signed-off-by: Dirk Eibach Signed-off-by: Stefan Roese --- MAINTAINERS | 4 + MAKEALL | 1 + Makefile | 3 + board/gdsys/neo/Makefile | 51 ++++++++ board/gdsys/neo/config.mk | 24 ++++ board/gdsys/neo/neo.c | 101 ++++++++++++++++ board/gdsys/neo/u-boot.lds | 132 +++++++++++++++++++++ include/configs/neo.h | 231 +++++++++++++++++++++++++++++++++++++ 8 files changed, 547 insertions(+) create mode 100644 board/gdsys/neo/Makefile create mode 100644 board/gdsys/neo/config.mk create mode 100644 board/gdsys/neo/neo.c create mode 100644 board/gdsys/neo/u-boot.lds create mode 100644 include/configs/neo.h diff --git a/MAINTAINERS b/MAINTAINERS index 9c0d6bf8d..60cb6a6d5 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -130,6 +130,10 @@ Jon Diekema sbc8260 MPC8260 +Dirk Eibach + + neo PPC405EP + Dave Ellis SXNI855T MPC8xx diff --git a/MAKEALL b/MAKEALL index 847c1fa35..aa602b72d 100755 --- a/MAKEALL +++ b/MAKEALL @@ -211,6 +211,7 @@ LIST_4xx=" \ ml300 \ ml507 \ ml507_flash \ + neo \ ocotea \ OCRTC \ ORSG \ diff --git a/Makefile b/Makefile index e83106156..fceb8a229 100644 --- a/Makefile +++ b/Makefile @@ -1385,6 +1385,9 @@ ml507_config: unconfig >> $(obj)board/xilinx/ml507/config.tmp @$(MKCONFIG) ml507 ppc ppc4xx ml507 xilinx +neo_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc ppc4xx neo gdsys + ocotea_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx ocotea amcc diff --git a/board/gdsys/neo/Makefile b/board/gdsys/neo/Makefile new file mode 100644 index 000000000..1270feafc --- /dev/null +++ b/board/gdsys/neo/Makefile @@ -0,0 +1,51 @@ +# +# (C) Copyright 2007 +# Stefan Roese, DENX Software Engineering, sr@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS = $(BOARD).o +SOBJS = + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/gdsys/neo/config.mk b/board/gdsys/neo/config.mk new file mode 100644 index 000000000..1bdf5e4fc --- /dev/null +++ b/board/gdsys/neo/config.mk @@ -0,0 +1,24 @@ +# +# (C) Copyright 2000 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +TEXT_BASE = 0xFFFC0000 diff --git a/board/gdsys/neo/neo.c b/board/gdsys/neo/neo.c new file mode 100644 index 000000000..817ce17ff --- /dev/null +++ b/board/gdsys/neo/neo.c @@ -0,0 +1,101 @@ +/* + * (C) Copyright 2007-2008 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include + +#define HWTYPE_CCX16 1 +#define HWREV_300 3 + +int board_early_init_f(void) +{ + mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */ + mtdcr(uicer, 0x00000000); /* disable all ints */ + mtdcr(uiccr, 0x00000000); /* set all to be non-critical */ + mtdcr(uicpr, 0xFFFFFF80); /* set int polarities */ + mtdcr(uictr, 0x10000000); /* set int trigger levels */ + mtdcr(uicvcr, 0x00000001); /* set vect base=0,INT0 highest prio */ + mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */ + + /* + * EBC Configuration Register: set ready timeout to 512 ebc-clks + * -> ca. 15 us + */ + mtebc(epcr, 0xa8400000); /* ebc always driven */ + + return 0; +} + +/* + * Check Board Identity: + */ +int checkboard(void) +{ + char *s = getenv("serial#"); + u16 val = in_le16((void *)CONFIG_FPGA_BASE + 2); + u8 unit_type; + u8 hardware_cpu_ports; + u8 hardware_con_ports; + u8 hardware_version; + + printf("Board: CATCenter Neo"); + + if (s != NULL) { + puts(", serial# "); + puts(s); + } + puts("\n "); + + unit_type = (val & 0xf000) >> 12; + hardware_cpu_ports = ((val & 0x0f00) >> 8) * 8; + hardware_con_ports = ((val & 0x00f0) >> 4) * 2; + hardware_version = val & 0x000f; + + switch (unit_type) { + case HWTYPE_CCX16: + printf("CCX16-FPGA (80 UARTs)"); + break; + + default: + printf("UnitType %d, unsupported", unit_type); + break; + } + + printf(", %d cpu ports, %d console ports,", + hardware_cpu_ports, hardware_con_ports); + + switch (hardware_version) { + case HWREV_300: + printf(" HW-Ver 3.00\n"); + break; + + default: + printf(" HW-Ver %d, unsupported\n", + hardware_version); + break; + } + + return 0; +} diff --git a/board/gdsys/neo/u-boot.lds b/board/gdsys/neo/u-boot.lds new file mode 100644 index 000000000..d803625b5 --- /dev/null +++ b/board/gdsys/neo/u-boot.lds @@ -0,0 +1,132 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/ppc4xx/start.o (.text) + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss (NOLOAD) : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/include/configs/neo.h b/include/configs/neo.h new file mode 100644 index 000000000..f275c7b2a --- /dev/null +++ b/include/configs/neo.h @@ -0,0 +1,231 @@ +/* + * (C) Copyright 2007-2008 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + + +#define CONFIG_405EP 1 /* this is a PPC405 CPU */ +#define CONFIG_4xx 1 /* member of PPC4xx family */ +#define CONFIG_NEO 1 /* on a Neo board */ + +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME neo +#include "amcc-common.h" + +#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f */ + +#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ + +/* + * Configure PLL + */ +#define PLLMR0_DEFAULT PLLMR0_266_133_66_33 +#define PLLMR1_DEFAULT PLLMR1_266_133_66_33 + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +#define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environment vars */ + +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + "kernel_addr=fc000000\0" \ + "fdt_addr=fc1e0000\0" \ + "ramdisk_addr=fc200000\0" \ + "" + +#define CONFIG_PHY_ADDR 4 /* PHY address */ +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#define CONFIG_PHY1_ADDR 0xc /* EMAC1 PHY address */ +#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ + +/* + * Commands additional to the ones defined in amcc-common.h + */ +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DTT +#undef CONFIG_CMD_EEPROM + +/* + * SDRAM configuration (please see cpu/ppc/sdram.[ch]) + */ +#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ + +/* SDRAM timings used in datasheet */ +#define CONFIG_SYS_SDRAM_CL 3 /* CAS latency */ +#define CONFIG_SYS_SDRAM_tRP 20 /* PRECHARGE command period */ +#define CONFIG_SYS_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE command period */ +#define CONFIG_SYS_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */ +#define CONFIG_SYS_SDRAM_tRFC 66 /* Auto refresh period */ + +/* + * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1. + * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31. + * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value. + * The Linux BASE_BAUD define should match this configuration. + * baseBaud = cpuClock/(uartDivisor*16) + * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, + * set Linux BASE_BAUD to 403200. + */ +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ +#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ +#define CONFIG_SYS_BASE_BAUD 691200 + +/* + * I2C stuff + */ +#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ + +/* RTC */ +#define CONFIG_RTC_DS1337 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 + +/* Temp sensor/hwmon/dtt */ +#define CONFIG_DTT_LM63 1 /* National LM63 */ +#define CONFIG_DTT_SENSORS { 0 } /* Sensor addresses */ +#define CONFIG_DTT_PWM_LOOKUPTABLE \ + { { 40, 10 }, { 50, 20 }, { 60, 40 } } +#define CONFIG_DTT_TACH_LIMIT 0xa10 + +/* + * FLASH organization + */ +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ +#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ + +#define CONFIG_SYS_FLASH_BASE 0xFC000000 +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ + +#ifdef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) +#endif + +/* + * PPC405 GPIO Configuration + */ +#define CONFIG_SYS_4xx_GPIO_TABLE { /* GPIO Alternate1 */ \ +{ \ +/* GPIO Core 0 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO0 PerBLast */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO1 TS1E */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO2 TS2E */ \ +{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO3 TS1O */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO4 TS2O */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO5 TS3 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO6 TS4 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO7 TS5 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO8 TS6 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO9 TrcClk */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO10 PerCS1 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO11 PerCS2 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO12 PerCS3 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO13 PerCS4 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO14 PerAddr03 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO15 PerAddr04 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO16 PerAddr05 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO17 IRQ0 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO18 IRQ1 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO19 IRQ2 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO20 IRQ3 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO21 IRQ4 */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO22 IRQ5 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO23 IRQ6 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO24 UART0_DCD */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO25 UART0_DSR */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO26 UART0_RI */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO27 UART0_DTR */ \ +{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO28 UART1_Rx */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO29 UART1_Tx */ \ +{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO30 RejectPkt0 */ \ +{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO31 RejectPkt1 */ \ +} \ +} + +/* + * Definitions for initial stack pointer and data area (in data cache) + */ +/* use on chip memory (OCM) for temperary stack until sdram is tested */ +#define CONFIG_SYS_TEMP_STACK_OCM 1 + +/* On Chip Memory location */ +#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 +#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ +#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* + * External Bus Controller (EBC) Setup + */ + +/* Memory Bank 0 (NOR-FLASH) initialization */ +#define CONFIG_SYS_EBC_PB0AP 0x92015480 +#define CONFIG_SYS_EBC_PB0CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit */ + +/* Memory Bank 1 (NVRAM) initialization */ +#define CONFIG_SYS_EBC_PB1AP 0x92015480 +#define CONFIG_SYS_EBC_PB1CR 0xFB85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */ + +/* Memory Bank 2 (FPGA) initialization */ +#define CONFIG_FPGA_BASE 0x7f100000 +#define CONFIG_SYS_EBC_PB2AP 0x92015480 +#define CONFIG_SYS_EBC_PB2CR 0x7f11a000 /* BAS=0x7f1,BS=1MB,BU=R/W,BW=16bit */ + +/* Memory Bank 3 (Latches) initialization */ +#define CONFIG_SYS_EBC_PB3AP 0x92015480 +#define CONFIG_SYS_EBC_PB3CR 0x7f21a000 /* BAS=0x7f2,BS=1MB,BU=R/W,BW=16bit */ + +#endif /* __CONFIG_H */ From 43cbce69d48d052574d71f50724be546d90a46a4 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Mon, 13 Oct 2008 10:45:14 +0200 Subject: [PATCH 7/8] ppc4xx: Correctly setup ranges property in ebc node Previously only the NOR flash mapping was written into the ranges property of the ebc node. This patch now writes all enabled chip select areas into the ranges property. Signed-off-by: Stefan Roese --- cpu/ppc4xx/fdt.c | 45 ++++++++++++++++++++++-------------- include/asm-ppc/ppc4xx-ebc.h | 31 +++++++++++++++++++++++++ 2 files changed, 59 insertions(+), 17 deletions(-) diff --git a/cpu/ppc4xx/fdt.c b/cpu/ppc4xx/fdt.c index a97484fa7..c55e1cfbb 100644 --- a/cpu/ppc4xx/fdt.c +++ b/cpu/ppc4xx/fdt.c @@ -37,29 +37,40 @@ DECLARE_GLOBAL_DATA_PTR; void __ft_board_setup(void *blob, bd_t *bd) { - u32 val[4]; int rc; + int i; + u32 bxcr; + u32 ranges[EBC_NUM_BANKS * 4]; + u32 *p = ranges; + char *ebc_path = "/plb/opb/ebc"; ft_cpu_setup(blob, bd); - /* Fixup NOR mapping */ - val[0] = 0; /* chip select number */ - val[1] = 0; /* always 0 */ - val[2] = gd->bd->bi_flashstart; - val[3] = gd->bd->bi_flashsize; - if (fdt_path_offset(blob, "/plb/opb/ebc") >= 0) { - rc = fdt_find_and_setprop(blob, "/plb/opb/ebc", "ranges", - val, sizeof(val), 1); - } else { - /* - * Some 405 PPC's have EBC as direct PLB child in the dts - */ - rc = fdt_find_and_setprop(blob, "/plb/ebc", "ranges", - val, sizeof(val), 1); + /* + * Read 4xx EBC bus bridge registers to get mappings of the + * peripheral banks into the OPB/PLB address space + */ + for (i = 0; i < EBC_NUM_BANKS; i++) { + mtdcr(ebccfga, EBC_BXCR(i)); + bxcr = mfdcr(ebccfgd); + + if ((bxcr & EBC_BXCR_BU_MASK) != EBC_BXCR_BU_NONE) { + *p++ = i; + *p++ = 0; + *p++ = bxcr & EBC_BXCR_BAS_MASK; + *p++ = EBC_BXCR_BANK_SIZE(bxcr); + } } - if (rc) - printf("Unable to update property NOR mapping, err=%s\n", + + /* Some 405 PPC's have EBC as direct PLB child in the dts */ + if (fdt_path_offset(blob, "/plb/opb/ebc") < 0) + strcpy(ebc_path, "/plb/ebc"); + rc = fdt_find_and_setprop(blob, ebc_path, "ranges", ranges, + (p - ranges) * sizeof(u32), 1); + if (rc) { + printf("Unable to update property EBC mappings, err=%s\n", fdt_strerror(rc)); + } } void ft_board_setup(void *blob, bd_t *bd) __attribute__((weak, alias("__ft_board_setup"))); diff --git a/include/asm-ppc/ppc4xx-ebc.h b/include/asm-ppc/ppc4xx-ebc.h index d180e045f..9680f70d6 100644 --- a/include/asm-ppc/ppc4xx-ebc.h +++ b/include/asm-ppc/ppc4xx-ebc.h @@ -35,7 +35,38 @@ #define CONFIG_EBC_PPC4xx_IBM_VER1 #endif +/* + * Define the max number of EBC banks (chip selects) + */ +#if defined(CONFIG_405CR) || defined(CONFIG_405GP) || \ + defined(CONFIG_405EZ) || \ + defined(CONFIG_440GP) || defined(CONFIG_440GX) +#define EBC_NUM_BANKS 8 +#endif + +#if defined(CONFIG_405EP) +#define EBC_NUM_BANKS 5 +#endif + +#if defined(CONFIG_405EX) || \ + defined(CONFIG_460SX) +#define EBC_NUM_BANKS 4 +#endif + +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_460EX) || defined(CONFIG_460GT) +#define EBC_NUM_BANKS 6 +#endif + +#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#define EBC_NUM_BANKS 3 +#endif + /* Bank Configuration Register */ +#define EBC_BXCR(n) (n) +#define EBC_BXCR_BANK_SIZE(n) (0x100000 << (((n) & EBC_BXCR_BS_MASK) >> 17)) + #define EBC_BXCR_BAS_MASK PPC_REG_VAL(11, 0xFFF) #define EBC_BXCR_BAS_ENCODE(n) (((static_cast(u32, n)) & EBC_BXCR_BAS_MASK)) #define EBC_BXCR_BS_MASK PPC_REG_VAL(14, 0x7) From f4d14c55504ce40287321bd63ee269e3233ee4ae Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Mon, 13 Oct 2008 15:15:31 +0200 Subject: [PATCH 8/8] ppc4xx: Add 1.0 & 1.066 GHz to canyonlands bootstrap command for PLL setup Signed-off-by: Stefan Roese --- board/amcc/canyonlands/bootstrap.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/board/amcc/canyonlands/bootstrap.c b/board/amcc/canyonlands/bootstrap.c index 6b7474355..b1f4a213d 100644 --- a/board/amcc/canyonlands/bootstrap.c +++ b/board/amcc/canyonlands/bootstrap.c @@ -40,6 +40,8 @@ static char *config_labels[] = { "CPU: 600 PLB: 200 OPB: 100 EBC: 100", "CPU: 800 PLB: 200 OPB: 100 EBC: 100", + "CPU:1000 PLB: 200 OPB: 100 EBC: 100", + "CPU:1066 PLB: 266 OPB: 88 EBC: 88", NULL }; @@ -54,6 +56,16 @@ static u8 boot_configs[][17] = { 0x86, 0x80, 0xba, 0x14, 0x99, 0x80, 0x00, 0xa0, 0x40, 0x08, 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00 }, + { + (NAND_COMPATIBLE | NOR_COMPATIBLE), + 0x86, 0x82, 0x96, 0x19, 0xb9, 0x80, 0x00, 0xa0, 0x40, 0x08, + 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00 + }, + { + (NAND_COMPATIBLE | NOR_COMPATIBLE), + 0x86, 0x80, 0xb3, 0x01, 0x9d, 0x80, 0x00, 0xa0, 0x40, 0x08, + 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00 + }, { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0