L1CTL is using the network byte order, because this protocol is
spoken between different devices and architectures. Somehow I
forgot about this while adding SETFH command back in 2018.
Change-Id: Ia2f70f0d5e35b6bf05e1fa6fb51a15c1bbe3ca4c
Related: OS#4546
It would make sense to send the ARFCN list in parameters of SETFH
command, if there was a clear distinction between transceivers in
fake_trx.py, i.e. which one is an MS and which is a BTS.
Right now, every Transceiver is an abstract entity that emits
and receives bursts. So when you convert an ARFCN to a pair of
Downlink/Uplink frequencies, you don't know whether it maps
as Rx/Tx or as Tx/Rx for a given Transceiver.
Of course, we could assume that this is an MS specific feature,
and a pair of Downlink/Uplink frequencies always corresponds to
Rx/Tx, but what if some day we would need to implement and test
a similar approach for the BTS side? Also, by sending frequency
values in kHz (rather than ARFCNs) we can avoid inconsistency
with the existing RXTUNE / TXTUNE commands.
Change-Id: Ia2bf08797f1a37b56cf47945694b901f92765b58
Related: I587e4f5da67c7b7f28e010ed46b24622c31a3fdd
Related: OS#4546
L1CTL handling code should not be involved in such high level checks, so
while at it, move the check into a separate function in gsm48_rr.c and
add a length check. gsm48_rr_tx_voice() is the only caller of
l1ctl_tx_traffic_req().
Related: SYS#4924
Change-Id: Iba84f5d60ff5b1a2db8fb6af5131e185965df7c9
Use newly added audio / loopback config vty node to provide audio
loopback from mobile app. Only FR is supported for now.
Change-Id: Icd0b8d00c855db1a6ff5e35e10c8ff67b7ad5c83
The aim is to add configurable audio loopback to mobile. An existing patch on a
branch from fixeria [1] adds the audio config section. Add a reduced version of
this audio config to be compatible with the future merge.
Add the audio loopback setting, so far without functionality.
Subsequent patch adds the actual loopback.
[1] osmocom-bb branch fixeria/audio,
patch "mobile/vty_interface.c: add new 'audio' section"
Change-id I62cd5ef22ca2290fcafe65c78537ddbcb39fb8c6
Change-Id: Ie03e4a6c6f81ea3925266dd22e87506d722a6e1a
Since we're heavily using trxcon in ttcn3-bts-test, the logging
output should contain as much information as possible. Ideally
we should introduce the VTY interface (see OS#3666) and get
logging configuration options as a bonus. But let's just use
some beneficial hard-coded defaults for now:
- print category and level (huh, we use NOTICE everywhere?),
- do not print category-hex (who needs it anyway?),
- print extended timestamp, so we're in synce with other logs.
P.S. This configuration is based on my own debugging experience.
Change-Id: Ie3d259f3255d8af80e6780f850b808fa243f97b4
GPRS (PDCH) and CBCH related frames have nothing to do with LAPDm.
The former uses LLC for the user-plane data, while CBCH involves
its own segmentation described in 3GPP TS 23.041 and TS 44.012.
There is currently no code for handling these kinds of frames, so
let's just send them to GSMTAP and release the memory (msgb).
Change-Id: I59b4acbe22217f8989f73b79b128a43e8bcdfa2f
Related: OS#4439
As was noted by Pau Espin Pedrol, there is a theoretical chance
that lchan->tdma.num_proc would overflow, so as a consequence,
subst_frame_loss() will be unable to compensate one
(potentionally lost) Downlink burst.
On practice, given the size of unsigned long and duration of a
single TDMA frame, it would only happen once in roughly ~6 years.
FRAME_DURATION = 4615 * 10e-6
ULONG_MAX = 2 ** 32 - 1
FRAME_DURATION * ULONG_MAX -> ~198212740 seconds
-> ~55059 hours
-> ~2294 days
-> ~6 years.
Chances are that trxcon would crash much earlier, or even GSM
would be completely forgotten after such a long time run, but
let's work this around and simply start counting from 1
if that overflow eventually happens.
Change-Id: I3d40ef09b06039a85df52af06ab38de314e1a434
It may happen that the burst reception would start from bid != 0:
<0005> sched_trx.c:263 (Re)configure TDMA timeslot #2 as TCH/H+SACCH
<0005> sched_trx.c:420 Activating lchan=TCH/H(0) on ts=2
<0005> sched_trx.c:420 Activating lchan=SACCH/TH(0) on ts=2
<0006> sched_lchan_xcch.c:96 Received incomplete data frame at fn=0 (0/104) for SACCH/TH(0)
<0006> sched_lchan_xcch.c:106 Received bad data frame at fn=0 (0/104) for SACCH/TH(0)
so in that case, both measurement processing and the frame number
calculation would yield incorrect and/or incomplete results. The
Rx burst mask can be used to eliminate this problem.
In particular, if we shift it left instead of cleaning, it would
never be equal 0x00 after at least one burst is received. This
would allow us to skip decoding of an incomplete frame at the
beginning when the logical channel was just activated.
Note that TCH/H handler is not affected because it already uses
the strategy described above, so we keep it unchanged.
Change-Id: Ib8ddf2edd5ef84f2ab12155f7a8874c9fc56d436
Related: OS#3554
It may happen that one or more Downlink bursts are lost on their
way to the MS due to a variety of reasons. Modern transceivers
supporting TRXDv1 protocol would substitute lost bursts with
so-called NOPE indications. Hovewer, neither fake_trx.py nor
grgsm_trx do support this feature at the moment.
We can still detect and compensate TDMA frame loss per logical
channels in the same way as it's already done in osmo-bts-trx.
In short, we should keep TDMA frame number of the last received
burst in the logical channel state, and using the appropriate
multiframe layout, check if there were any gaps between TDMA
frame number of the current burst and the stored one.
Change-Id: I3551d79796a3730565c2c70577e9d134e636f275
Using TDMA frame number of a burst with bid=0 is fine for xCCH,
but not for TCH and FACCH, because they use the block-diagonel
interleaving. A single block on TCH may be interleaved over
8, 4 or even 6 consecutive bursts depending on its type.
Since we now have the measurement history, we can attach TDMA
frame number to each measurement set, and then look up N-th
one when averaging the measurements in sched_trx_meas_avg().
Change-Id: I9221957297a6154edc1767a0e3753f5ee383173f
This allows us to bind the multicast sockets to a given network device
and/or to set the TTL of the multicast frames and hence control their
reach in terms of number of network hops.
Change-Id: Ia74aa381a4c1921cb8c7e263842a864ea8028139
Related: OS#2966
The files are used in both projects, and while the osmo-bts code has
evolved, this copy didn't. Let's sync again (to libosmocore
change-Id I303f2e616d2d32b5a8005c3dcf0f5fad19ad3445).
Change-Id: I189ee28a85a6d7a7a07b062f6b07012478503e8f
Depends: libosmocore.git Ib52d22710020b56965aefcef09bde8247ace4a9c
Related: OS#2966
In case we get assignments to secondary TRXs, the ARFCN of that
TRX must be used, and not the serving cell BCCH ARFCN.
Change-Id: Ief6cf5816969d819ff9506be70bec9b8d0d9d9be
GSMTAP_CHANNEL_VOICE is the mechanism by which GSMTAP can [finally!]
be used to transport circuit-switched voice codec payload, and not
just signalling.
Original patch by Neels Hofmeyr, heavily extended by Harald Welte.
Change-Id: Id72cf23b7c6587efae4cdaa7b50ab4d85b8c8d22
These BFI (Bad Frame Indications) substitute speech frames stolen
by FACCH/F or FACCH/H frames, so there can be no bit errors in
something that was not even transmitted over the air interface.
Change-Id: Icdb6209f75ead6581e3c18aeee0da9831aaa272a
According to 3GPP TS 45.003, clauses 4.2.5 and 4.3.5:
- one FACCH/F frame steals a single speech frame,
- one FACCH/H frame steals two speech frames.
A BFI (Bad Frame Indication) needs to be sent for each stolen
speech frame. This does not apply to CSD (data) channels though.
The BFI frames must have measurement data attached to them, and
due to their virtual nature (they do not actually come from the
air interface), the measurements must be crafted by trxcon.
Assigning a negative value to n_errors makes the code below the
'bfi' label craft fake measurement data. Otherwise, the actual
measurements belonging to the FACCH frame will be used.
Change-Id: Ia2f7c3cf7b1ef3737da6b1818cae2f001ee8768f
So far we used to store the sums of ToA and RSSI measurements in the
logical channel state, and after decoding of a block, we did calculate
the average. This approach works fine for xCCH and PDTCH, but when it
comes to block-diagonal interleaving (which is used on TCH/F and TCH/H
channels), the results are incorrect. The problem is that a burst on
TCH may carry 57 bits of one encoded frame and 57 bits of another.
Instead of calculating the sum of measurements on the fly, let's push
them into a circular buffer (the measurement history), and keep them
there even after decoding of a block. This would allow us to calculate
the average of N last measurements depending on the interleaving type.
A single circular buffer can hold up to 8 unique measurements, so the
recent measurements would basically override the oldest ones.
Change-Id: I211ee3314f0a284112a4deddc0e93028f4a27cef
In Change-Id Ia94ebf22a2ec439dfe1f31d703b832ae57b48ef2 we
introduced a new member to the ccch_mode enum: CCCH_MODE_COMBINED_CBCH,
which is to be used to tell the PHY if a CBCH is present on the combined
CCCH+SDCCH/4+CBCH or not (CCCH+SDCCH4).
This was implemented in trxcon + calypso firmware, but cbch_sniff has
not been updated accordingly.
Related: OS#4439
Change-Id: I429d45cfb181da4a2e767e92f1213ccd08c6d440
Doing so can create a number of warning messages in e.g. 'mobile'
like
<0015> lapd_core.c:1239 Unnumbered frame not allowed. (dl=0x55c632f9f220)
<0015> lapd_core.c:392 sending MDL-ERROR-IND cause 12 from state LAPD_STATE_IDLE (dl=0x55c632f9f220)
<0015> lapdm.c:481 sending MDL-ERROR-IND 12
<0001> gsm48_rr.c:4977 MDL-Error (cause 12) ignoring
Change-Id: I2cf65be5b2f879fe940e08c9f369bc1cada7b0dd
Closes: OS#4439
We so far relied on it being free'd once the TDMA item is free'd,
but let's make it more explicit. After we've unlinked it from the
list, nobody is going to reference it ever again.
Change-Id: I57a596428be10ce720e0b528ecfc44a70e3e3078
That function encapsulates the RTP payload in an MNCC header, but the l1ctl dl
header has to be removed first to get only the RTP payload in the MNCC
structure.
Change-Id: Id6ddc9b1da43e88c5b9468d4397a39953bdf533a
This pointer cs->si stores an address to the System Information of
a currently selected cell. When we release System Information,
ensure that it does not point to free()d memory.
Change-Id: Ife2ddf7274a48447a9ded9035f9dd01befaf2e6c
Some applications (e.g. ccch_scan) may not initialize ms->cellsel.si,
some (e.g. mobile) may need some time to initialize it. Let's assume
that 'bs_ag_blks_res' is 1 if System Information is not available.
Change-Id: Ie695d9700c01ee1e6778950a2f3c8610b69d2143
During 3.19->3.20 dev cycle, some fields were transformed from
timestamp_t or double to timespec_t. See for instance gpsd.git
f7c230fceb6d64483757f8c32afb98e6a2cb9413.
Change-Id: Ie8ba19d030b6f46f2d8afc270a732ce8c26c438f
Vadim Yanitskiy
Harald Welte
Oliver Smith
Neels Hofmeyr
Pau Espin