649 lines
29 KiB
Plaintext
649 lines
29 KiB
Plaintext
configs/pic32mx README
|
|
=====================
|
|
|
|
This README file discusses the port of NuttX to the "Advanced USB Storage
|
|
Demo Board," Model DB-DP11215, from Sure Electronics
|
|
(http://www.sureelectronics.net/). This board features the MicroChip
|
|
PIC32MX440F512H. See also http://www.sureelectronics.net/goods.php?id=1168
|
|
for further information about the Sure DB-DP11215 board.
|
|
|
|
DB_DP11215 PIC32 Storage Demo Board
|
|
|
|
- PIC32MX44F512H
|
|
- SD card slot
|
|
- RS-2323 Interface
|
|
- USB (MINI-B)
|
|
- 2x16 LCD display
|
|
- Three tactile switches
|
|
- Four user LEDs
|
|
|
|
Also available (but not yet supported).
|
|
|
|
DB-DP11212 PIC32 General Purpose Demo Board
|
|
|
|
- PIC32MX44F512H
|
|
- LM75A temperature sensor and temperature resistor (NTC-SMD thermistor)
|
|
- SPI FLASH: AT25DF041A
|
|
- USB (MINI-B)
|
|
- 2x16 LCD display
|
|
- 4 digit, 8 segment LED display
|
|
- Three tactile switches
|
|
- Four user LEDs
|
|
|
|
Contents
|
|
========
|
|
|
|
PIC32MX440F512H Pin Out
|
|
Toolchains
|
|
Loading NuttX with PICkit2
|
|
PIC32MX Configuration Options
|
|
Configurations
|
|
|
|
PIC32MX440F512H Pin Out
|
|
=======================
|
|
|
|
DB_DP11215 PIC32 Storage Demo Board
|
|
-----------------------------------
|
|
PIC32MX440F512H 64-Pin QFN (USB) Pin Out as used on the DB_DP11215 PIC32 Storage
|
|
Demo Board.
|
|
|
|
LEFT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
|
|
PIN NAME SIGNAL NOTES
|
|
---- ----------------------------- -------------- -------------------------------
|
|
1 PMD5/RE5 PMPD5 Display, JP1-12, DB4
|
|
2 PMD6/RE6 PMPD6 Display, JP1-13, DB6
|
|
3 PMD7/RE7 PMPD7 Display, JP1-14, DB7
|
|
4 SCK2/PMA5/CN8/RG6 SCK SD connector SCK, FLASH (U1) SCK*
|
|
5 SDI2/PMA4/CN9/RG7 SDI SD connector DO, FLASH (U1) SO*
|
|
6 SDO2/PMA3/CN10/RG8 SDO SD connector DI, FLASH (U1) SI*
|
|
7 MCLR\ PIC_MCLR Pulled high, J7-1, ICSP
|
|
8 SS2/PMA2/CN11/RG9 UTIL_CS FLASH (U1) CS*
|
|
9 Vss Grounded
|
|
10 Vdd +3.3V ---
|
|
11 AN5/C1IN+/Vbuson/CN7/RB5 Vbuson/AN5/RB5 To USB VBUS circuitry
|
|
12 AN4/C1IN-/CN6/RB4 SW_OK SW3, Pull high, low means SW3 closed
|
|
13 AN3/C2IN+/CN5/RB3 SW_UP SW1, Pull high, low means SW1 closed
|
|
14 AN2/C2IN-/CN4/RB2 SW_Down SW2, Pull high, low means SW2 closed
|
|
15 PGEC1/AN1/Vref-/CVref-/CN3/ ADC_SENSE_SWITCHED_+VBUS To USB VBUS circuitry
|
|
RB1
|
|
16 PGED1/AN0/VREF+/CVREF+/PMA6/ N/C Not connected
|
|
CN2/RB0
|
|
|
|
*FLASH (U1, SOIC) not populated
|
|
|
|
BOTTOM SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
|
|
PIN NAME SIGNAL NOTES
|
|
---- ----------------------------- -------------- -------------------------------
|
|
17 PGEC2/AN6/OCFA/RB6 PIC_PGC2 J7-5, ICSP
|
|
18 PGED2/AN7/RB7 PIC_PGD2 J7-4, ICSP
|
|
19 AVdd +3.3V ---
|
|
20 AVss Grounded
|
|
21 AN8/U2CTS/C1OUT/RB8 N/C Not connected
|
|
22 AN9/C2OUT/PMA7/RB9 N/C Not connected
|
|
23 TMS/AN10/CVREFOUT/PMA13/RB10 UTIL_WP FLASH (U1) WP*
|
|
24 TDO/AN11/PMA12/RB11 SD_CS SD connector CS
|
|
25 Vss Grounded
|
|
26 Vdd +3.3V ---
|
|
27 TCK/AN12/PMA11/RB12 SD_CD SD connector CD
|
|
28 TDI/AN13/PMA10/RB13 SD_WD SD connector WD
|
|
29 AN14/U2RTS/PMALH/PMA1/RB14 N/C Not connected
|
|
30 AN15/OCFB/PMALL/PMA0/CN12/ PMPA0 Display, JP1-4, RS
|
|
RB15
|
|
31 SDA2/U2RX/PMA9/CN17/RF4 RXD2_MCU J5 DB9 via RS232 driver
|
|
32 SCL2/U2TX/PMA8/CN18/RF5 TXD2_MCU J5 DB9 via RS232 driver
|
|
|
|
*FLASH (U1, SOIC) not populated
|
|
|
|
RIGHT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
|
|
PIN NAME SIGNAL NOTES
|
|
---- ----------------------------- -------------- -------------------------------
|
|
48 SOSCO/T1CK/CN0/RC14 SOSCO 32.768KHz XTAL (Y1)
|
|
47 SOSCI/CN1/RC13 SOSCI 32.768KHz XTAL (Y1)
|
|
46 OC1/INT0/RD0 PWM1 Used to control backlight level (K)
|
|
45 IC4/PMCS1/PMA14/INT4/RD11 PMPCS1 Display, JP1-6, E
|
|
44 SCL1/IC3/PMCS2/PMA15/INT3/ USB_OPT USB PHY
|
|
RD10
|
|
43 U1CTS/SDA1/IC2/INT2/RD9 USB_OPTEN USB PHY
|
|
42 RTCC/IC1/INT1/RD8 N/C Not connected
|
|
41 Vss Grounded
|
|
40 OSC2/CLKO/RC15 OSC2 20MHz XTAL (Y2)
|
|
39 OSC1/CLKI/RC12 OSC1 20MHz XTAL (Y2)
|
|
38 Vdd +3.3V ---
|
|
37 D+/RG2 APPS_D+ USB connectors via PHY
|
|
36 D-/RG3 APPS_D- USB connectors via PHY
|
|
35 Vusb +3.3V ---
|
|
34 Vbus VBUS_DEVICE_MODE Display, USB Mini-B, USB Type A, JP1-1, +5V
|
|
33 USBID/RF3 N/C Not connected
|
|
|
|
TOP SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
|
|
PIN NAME SIGNAL NOTES
|
|
---- ----------------------------- -------------- -------------------------------
|
|
64 PMPD4/RE4 PMPD4 Display, JP1-11, DB4
|
|
63 PMPD3/RE3 PMPD3 Display, JP1-10, DB3
|
|
62 PMPD2/RE2 PMPD2 Display, JP1-9, DB2
|
|
61 PMPD1/RE1 PMPD1 Display, JP1-8, DB1
|
|
60 PMPD0/RE0 PMPD0 Display, JP1-7, DB0
|
|
59 RF1 RF1 Low illuminates LED/R/ERR
|
|
58 RF0 RF0 Low illuminates LED/Y/flash
|
|
57 ENVREG ENVREG Pulled high
|
|
56 Vcap/Vddcore VDDCORE Capactors to ground
|
|
55 CN16/RD7 RD7 Low illuminates LED/Y/USB
|
|
54 CN15/RD6 RD6 Low illuminates LED/Y/SD
|
|
53 PMRD/CN14/RD5 PMPRD Display, JP1-5, R/W
|
|
52 OC5/IC5/PMWR/CN13/RD4 N/C Not connected
|
|
51 U1TX/OC4/RD3 CP2102_RXD J6-3, UART1 (also CP2102*)
|
|
50 U1RX/OC3/RD2 CP2102_TXD J6-2, UART1 (also CP2102*)
|
|
49 U1RTS/OC2/RD1 PWM2 Used to control backlight level (Vo)
|
|
|
|
*USB-to-UART bridge (U1, CP2102) not populated
|
|
|
|
DB-DP11212 PIC32 General Purpose Demo Board
|
|
-------------------------------------------
|
|
PIC32MX440F512H 64-Pin QFN (USB) Pin Out as used on the DB-DP11212 PIC32 General
|
|
Purpose Demo Board
|
|
|
|
LEFT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
|
|
PIN NAME SIGNAL NOTES
|
|
---- ----------------------------- -------------- -------------------------------
|
|
1 PMD5/RE5 PMPD5 Display, JP1-12, DB5
|
|
2 PMD6/RE6 PMPD6 Display, JP1-13, DB6
|
|
3 PMD7/RE7 PMPD7 Display, JP1-14, DB7
|
|
4 SCK2/PMA5/CN8/RG6 SCK FLASH (U4) SCK*
|
|
5 SDI2/PMA4/CN9/RG7 SDI FLASH (U4) SO*
|
|
6 SDO2/PMA3/CN10/RG8 SDO FLASH (U4) SI*
|
|
7 MCLR\ PIC_MCLR Pulled high, J2-1, ICSP
|
|
8 SS2/PMA2/CN11/RG9 N/C Not connected
|
|
9 Vss Grounded
|
|
10 Vdd +3.3V ---
|
|
11 Vbuson/AN5/CN7/RB5 RB5 LCD SEG5 (F), U5-10
|
|
12 AN4/CN6/RB4 RB4 LCD SEG4 (E), U5-1
|
|
13 AN3/CN5/RB3 RB3 LCD SEG3 (D), U5-2
|
|
14 AN2/CN4/RB2 RB2 LCD SEG2 (C), U5-4
|
|
15 PGEC1/AN1/Vref-/CN3/RB1 RB1 LCD SEG1 (B), U5-7
|
|
16 PGED1/AN0/VREF+/CVREF+/PMA6/ RB0 LCD SEG0 (A), U5-11
|
|
CN2/RB0
|
|
|
|
*FLASH (U4, SOIC) not populated
|
|
|
|
BOTTOM SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
|
|
PIN NAME SIGNAL NOTES
|
|
---- ----------------------------- -------------- -------------------------------
|
|
17 PGEC2/AN6/OCFA/RB6 PIC_PGC2 J2-5, ICSP
|
|
18 PGED2/AN7/RB7 PIC_PGD2 J2-4, ICSP
|
|
19 AVdd +3.3V ---
|
|
20 AVss Grounded
|
|
21 AN8/U2CTS/RB8 RB8 LCD SEG6 (G), U5-5
|
|
22 AN9/PMA7/RB9 RB9 LCD SEG7 (DP), U5-3
|
|
23 TMS/AN10/PMA13/RB10 UTIL_WP FLASH (U4) WP*
|
|
24 TDO/AN11/PMA12/RB11 UTIL_CS FLASH (U4) CS*
|
|
25 Vss Grounded
|
|
26 Vdd +3.3V ---
|
|
27 TCK/AN12/PMA11/RB12 N/C Not connected
|
|
28 TDI/AN13/PMA10/RB13 N/C Not connected
|
|
29 AN14/U2RTS/PMA1/RB14 temp_AD temp_AD
|
|
30 AN15/PMA0/CN12/RB15 PMPA0 Display, JP1-4, RS
|
|
31 SDA2/U2RX/PMA9/CN17/RF4 SDA LM75/SO, U3-1, SDA
|
|
32 SCL2/U2TX/PMA8/CN18/RF5 SCL LM75/SO, U3-2, SCL
|
|
|
|
*FLASH (U4, SOIC) not populated
|
|
|
|
RIGHT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
|
|
PIN NAME SIGNAL NOTES
|
|
---- ----------------------------- -------------- -------------------------------
|
|
48 SOSCO/T1CK/CN0/RC14 SOSCO 32.768KHz XTAL (Y1)
|
|
47 SOSCI/CN1/RC13 SOSCI 32.768KHz XTAL (Y1)
|
|
46 OC1/INT0/RD0 RD0 LCD DIG1, U5-12
|
|
45 IC4/PMCS1/PMA14/RD11 PMCS1 Display, JP1-6, E
|
|
44 SCL1/PMCS2/PMA15 RD10 LCD DIG2, U5-9
|
|
43 SDA1/RD9 RD9 LCD DIG3, U5-8
|
|
42 RTCC/RD8 RD8 LCD DIG4, U5-6
|
|
41 Vss Grounded
|
|
40 OSC2/CLKO/RC15 OSC2 20MHz XTAL (Y2)
|
|
39 OSC1/CLKI/RC12 OSC1 20MHz XTAL (Y2)
|
|
38 Vdd +3.3V ---
|
|
37 D+ MCU_D+ USB connectors via PHY
|
|
36 D- MCU_D- USB connectors via PHY
|
|
35 Vusb +3.3V ---
|
|
34 Vbus +5V_DUSB Display, USB Mini-B, USB Type A, JP1-1, +5V
|
|
33 USBID/RF3 N/C Not connected
|
|
|
|
TOP SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
|
|
PIN NAME SIGNAL NOTES
|
|
---- ----------------------------- -------------- -------------------------------
|
|
64 PMPD4/RD4 PMPD4 Display, JP1-11, DB4
|
|
63 PMPD3/RD3 PMPD3 Display, JP1-10, DB3
|
|
62 PMPD2/RD2 PMPD2 Display, JP1-9, DB2
|
|
61 PMPD1/RD1 PMPD1 Display, JP1-8, DB1
|
|
60 PMPD0/RE0 PMPD0 Display, JP1-7, DB0
|
|
59 RF1 Key3 SW3-1
|
|
58 RF0 Key2 SW2-1
|
|
57 ENVREG ENVREG Pulled high
|
|
56 Vcap/Vddcore VDDCORE Capacitors to ground
|
|
55 CN16/RD7 N/C Not connected
|
|
54 CN15/RD6 Key5 SW5-1
|
|
53 PMRD/CN14/RD5 PMPRD ---
|
|
52 OC5/PMWR/CN13/RD4 PWM2 Used to control backlight level (Vo)
|
|
51 U1TX/OC4/RD3 N/C Not connected
|
|
50 U1RX/OC3/RD2 N/C Not connected
|
|
49 OC2/RD1 PWM1 Used to control backlight level (K)
|
|
|
|
Toolchains
|
|
==========
|
|
|
|
I am using the free, LITE version of the PIC32MX toolchain available
|
|
for download from the microchip.com web site. I am using the Windows
|
|
version. The MicroChip toolchain is the only toolchaing currently
|
|
supported in these configurations, but it should be a simple matter to
|
|
adapt to other toolchains by modifying the Make.defs file include in
|
|
each configuration.
|
|
|
|
Toolchain Options:
|
|
|
|
CONFIG_PIC32MX_MICROCHIPW - MicroChip full toolchain for Windows
|
|
CONFIG_PIC32MX_MICROCHIPL - MicroChip full toolchain for Linux
|
|
CONFIG_PIC32MX_MICROCHIPW_LITE - MicroChip LITE toolchain for Windows
|
|
CONFIG_PIC32MX_MICROCHIPL_LITE - MicroChip LITE toolchain for Linux
|
|
|
|
Windows Native Toolchains
|
|
|
|
NOTE: There are several limitations to using a Windows based toolchain in a
|
|
Cygwin environment. The three biggest are:
|
|
|
|
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
|
|
performed automatically in the Cygwin makefiles using the 'cygpath' utility
|
|
but you might easily find some new path problems. If so, check out 'cygpath -w'
|
|
|
|
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
|
|
are used in Nuttx (e.g., include/arch). The make system works around these
|
|
problems for the Windows tools by copying directories instead of linking them.
|
|
But this can also cause some confusion for you: For example, you may edit
|
|
a file in a "linked" directory and find that your changes had no effect.
|
|
That is because you are building the copy of the file in the "fake" symbolic
|
|
directory. If you use a Windows toolchain, you should get in the habit of
|
|
making like this:
|
|
|
|
make clean_context all
|
|
|
|
An alias in your .bashrc file might make that less painful.
|
|
|
|
3. Dependencies are not made when using Windows versions of the GCC. This is
|
|
because the dependencies are generated using Windows pathes which do not
|
|
work with the Cygwin make.
|
|
|
|
Support has been added for making dependencies with the windows-native toolchains.
|
|
That support can be enabled by modifying your Make.defs file as follows:
|
|
|
|
- MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
|
+ MKDEP = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
|
|
|
|
If you have problems with the dependency build (for example, if you are not
|
|
building on C:), then you may need to modify tools/mkdeps.sh
|
|
|
|
Loading NuttX with PICkit2
|
|
==========================
|
|
|
|
NOTE: You need a PICKit3 if you plan to use the MPLAB debugger! The PICKit2
|
|
can, however, still be used to load programs. Instructions for the PICKit3
|
|
are similar.
|
|
|
|
Intel Hex Forma Files:
|
|
----------------------
|
|
|
|
When NuttX is built it will produce two files in the top-level NuttX
|
|
directory:
|
|
|
|
1) nuttx - This is an ELF file, and
|
|
2) nuttx.hex - This is an Intel Hex format file. This is controlled by
|
|
the setting CONFIG_INTELHEX_BINARY in the .config file.
|
|
|
|
The PICkit tool wants an Intel Hex format file to burn into FLASH. However,
|
|
there is a problem with the generated nutt.hex: The tool expects the nuttx.hex
|
|
file to contain physical addresses. But the nuttx.hex file generated from the
|
|
top-level make will have address in the KSEG0 and KSEG1 regions.
|
|
|
|
tools/pic32mx/mkpichex:
|
|
----------------------
|
|
|
|
There is a simple tool in the NuttX tools/pic32mx directory that can be
|
|
used to solve both issues with the nuttx.hex file. But, first, you must
|
|
build the tool:
|
|
|
|
cd tools/pic32mx
|
|
make
|
|
|
|
Now you will have an excecutable file call mkpichex (or mkpichex.exe on
|
|
Cygwin). This program will take the nutt.hex file as an input, it will
|
|
convert all of the KSEG0 and KSEG1 addresses to physical address, and
|
|
it will write the modified file, replacing the original nuttx.hex.
|
|
|
|
To use this file, you need to do the following things:
|
|
|
|
. ./setenv.sh # Source setenv.sh. Among other this, this script
|
|
# will add the NuttX tools/pic32mx directory to your
|
|
# PATH variable
|
|
make # Build nuttx and nuttx.hex
|
|
mkpichex $PWD # Convert addresses in nuttx.hex. $PWD is the path
|
|
# to the top-level build directory. It is the only
|
|
# required input to mkpichex.
|
|
|
|
PIC32MX Configuration Options
|
|
=============================
|
|
|
|
General Architecture Settings:
|
|
|
|
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
|
be set to:
|
|
|
|
CONFIG_ARCH=mips
|
|
|
|
CONFIG_ARCH_family - For use in C code:
|
|
|
|
CONFIG_ARCH_MIPS=y
|
|
|
|
CONFIG_ARCH_architecture - For use in C code:
|
|
|
|
CONFIG_ARCH_MIPS32=y
|
|
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
|
|
CONFIG_ARCH_CHIP=pic32mx
|
|
|
|
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
|
chip:
|
|
|
|
CONFIG_ARCH_CHIP_PIC32MX440F512H=y
|
|
|
|
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
|
hence, the board that supports the particular chip or SoC.
|
|
|
|
CONFIG_ARCH_BOARD=sure-pic32mx
|
|
|
|
CONFIG_ARCH_DBDP11215 Distinguishes the DB_DP11215 PIC32 Storage
|
|
Demo Board
|
|
|
|
CONFIG_ARCH_DBDP11212 Distingustes the DB-DP11212 PIC32 General
|
|
Purpose Demo Board
|
|
|
|
CONFIG_ARCH_BOARD_name - For use in C code
|
|
|
|
CONFIG_ARCH_BOARD_SUREPIC32MX=y
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
|
of delay loops
|
|
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
|
endian)
|
|
|
|
CONFIG_DRAM_SIZE - Describes the installed DRAM (CPU SRAM in this case):
|
|
|
|
CONFIG_DRAM_SIZE=(32*1024) (32Kb)
|
|
|
|
There is an additional 32Kb of SRAM in AHB SRAM banks 0 and 1.
|
|
|
|
CONFIG_DRAM_START - The start address of installed DRAM
|
|
|
|
CONFIG_DRAM_START=0xa0000000
|
|
|
|
CONFIG_DRAM_END - Last address+1 of installed RAM
|
|
|
|
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
|
|
|
CONFIG_ARCH_IRQPRIO - The PIC32MXx supports interrupt prioritization
|
|
|
|
CONFIG_ARCH_IRQPRIO=y
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
|
have LEDs
|
|
|
|
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
stack. If defined, this symbol is the size of the interrupt
|
|
stack in bytes. If not defined, the user task stacks will be
|
|
used during interrupt handling.
|
|
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
|
|
|
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
|
cause a 100 second delay during boot-up. This 100 second delay
|
|
serves no purpose other than it allows you to calibratre
|
|
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
|
|
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
|
|
the delay actually is 100 seconds.
|
|
|
|
PIC32MX Configuration
|
|
|
|
CONFIG_PIC32MX_MVEC - Select muli- vs. single-vectored interrupts
|
|
|
|
Individual subsystems can be enabled:
|
|
|
|
CONFIG_PIC32MX_WDT - Watchdog timer
|
|
CONFIG_PIC32MX_T2 - Timer 2 (Timer 1 is the system time and always enabled)
|
|
CONFIG_PIC32MX_T3 - Timer 3
|
|
CONFIG_PIC32MX_T4 - Timer 4
|
|
CONFIG_PIC32MX_T5 - Timer 5
|
|
CONFIG_PIC32MX_IC1 - Input Capture 1
|
|
CONFIG_PIC32MX_IC2 - Input Capture 2
|
|
CONFIG_PIC32MX_IC3 - Input Capture 3
|
|
CONFIG_PIC32MX_IC4 - Input Capture 4
|
|
CONFIG_PIC32MX_IC5 - Input Capture 5
|
|
CONFIG_PIC32MX_OC1 - Output Compare 1
|
|
CONFIG_PIC32MX_OC2 - Output Compare 2
|
|
CONFIG_PIC32MX_OC3 - Output Compare 3
|
|
CONFIG_PIC32MX_OC4 - Output Compare 4
|
|
CONFIG_PIC32MX_OC5 - Output Compare 5
|
|
CONFIG_PIC32MX_I2C1 - I2C 1
|
|
CONFIG_PIC32MX_I2C2 - I2C 2
|
|
CONFIG_PIC32MX_SPI2 - SPI 2
|
|
CONFIG_PIC32MX_UART1 - UART 1
|
|
CONFIG_PIC32MX_UART2 - UART 2
|
|
CONFIG_PIC32MX_ADC - ADC 1
|
|
CONFIG_PIC32MX_PMP - Parallel Master Port
|
|
CONFIG_PIC32MX_CM1 - Comparator 1
|
|
CONFIG_PIC32MX_CM2 - Comparator 2
|
|
CONFIG_PIC32MX_RTCC - Real-Time Clock and Calendar
|
|
CONFIG_PIC32MX_DMA - DMA
|
|
CONFIG_PIC32MX_FLASH - FLASH
|
|
CONFIG_PIC32MX_USBDEV - USB device
|
|
CONFIG_PIC32MX_USBHOST - USB host
|
|
|
|
PIC32MX Configuration Settings
|
|
DEVCFG0:
|
|
CONFIG_PIC32MX_DEBUGGER - Background Debugger Enable. Default 3 (disabled). The
|
|
value 2 enables.
|
|
CONFIG_PIC32MX_ICESEL - In-Circuit Emulator/Debugger Communication Channel Select
|
|
Default 1 (PG2)
|
|
CONFIG_PIC32MX_PROGFLASHWP - Program FLASH write protect. Default 0xff (disabled)
|
|
CONFIG_PIC32MX_BOOTFLASHWP - Default 1 (disabled)
|
|
CONFIG_PIC32MX_CODEWP - Default 1 (disabled)
|
|
DEVCFG1: (All settings determined by selections in board.h)
|
|
DEVCFG2: (All settings determined by selections in board.h)
|
|
DEVCFG3:
|
|
CONFIG_PIC32MX_USBIDO - USB USBID Selection. Default 1 if USB enabled
|
|
(USBID pin is controlled by the USB module), but 0 (GPIO) otherwise.
|
|
CONFIG_PIC32MX_VBUSIO - USB VBUSON Selection (Default 1 if USB enabled
|
|
(VBUSON pin is controlled by the USB module, but 0 (GPIO) otherwise.
|
|
CONFIG_PIC32MX_WDENABLE - Enabled watchdog on power up. Default 0 (watchdog
|
|
can be enabled later by software).
|
|
|
|
The priority of interrupts may be specified. The value ranage of
|
|
priority is 4-31. The default (16) will be used if these any of these
|
|
are undefined.
|
|
|
|
CONFIG_PIC32MX_CTPRIO - Core Timer Interrupt
|
|
CONFIG_PIC32MX_CS0PRIO - Core Software Interrupt 0
|
|
CONFIG_PIC32MX_CS1PRIO - Core Software Interrupt 1
|
|
CONFIG_PIC32MX_INT0PRIO - External Interrupt 0
|
|
CONFIG_PIC32MX_INT1PRIO - External Interrupt 1
|
|
CONFIG_PIC32MX_INT2PRIO - External Interrupt 2
|
|
CONFIG_PIC32MX_INT3PRIO - External Interrupt 3
|
|
CONFIG_PIC32MX_INT4PRIO - External Interrupt 4
|
|
CONFIG_PIC32MX_FSCMPRIO - Fail-Safe Clock Monitor
|
|
CONFIG_PIC32MX_T1PRIO - Timer 1 (System timer) priority
|
|
CONFIG_PIC32MX_T2PRIO - Timer 2 priority
|
|
CONFIG_PIC32MX_T3PRIO - Timer 3 priority
|
|
CONFIG_PIC32MX_T4PRIO - Timer 4 priority
|
|
CONFIG_PIC32MX_T5PRIO - Timer 5 priority
|
|
CONFIG_PIC32MX_IC1PRIO - Input Capture 1
|
|
CONFIG_PIC32MX_IC2PRIO - Input Capture 2
|
|
CONFIG_PIC32MX_IC3PRIO - Input Capture 3
|
|
CONFIG_PIC32MX_IC4PRIO - Input Capture 4
|
|
CONFIG_PIC32MX_IC5PRIO - Input Capture 5
|
|
CONFIG_PIC32MX_OC1PRIO - Output Compare 1
|
|
CONFIG_PIC32MX_OC2PRIO - Output Compare 2
|
|
CONFIG_PIC32MX_OC3PRIO - Output Compare 3
|
|
CONFIG_PIC32MX_OC4PRIO - Output Compare 4
|
|
CONFIG_PIC32MX_OC5PRIO - Output Compare 5
|
|
CONFIG_PIC32MX_I2C1PRIO - I2C 1
|
|
CONFIG_PIC32MX_I2C2PRIO - I2C 2
|
|
CONFIG_PIC32MX_SPI2PRIO - SPI 2
|
|
CONFIG_PIC32MX_UART1PRIO - UART 1
|
|
CONFIG_PIC32MX_UART2PRIO - UART 2
|
|
CONFIG_PIC32MX_CN - Input Change Interrupt
|
|
CONFIG_PIC32MX_ADCPRIO - ADC1 Convert Done
|
|
CONFIG_PIC32MX_PMPPRIO - Parallel Master Port
|
|
CONFIG_PIC32MX_CM1PRIO - Comparator 1
|
|
CONFIG_PIC32MX_CM2PRIO - Comparator 2
|
|
CONFIG_PIC32MX_FSCMPRIO - Fail-Safe Clock Monitor
|
|
CONFIG_PIC32MX_RTCCPRIO - Real-Time Clock and Calendar
|
|
CONFIG_PIC32MX_DMA0PRIO - DMA Channel 0
|
|
CONFIG_PIC32MX_DMA1PRIO - DMA Channel 1
|
|
CONFIG_PIC32MX_DMA2PRIO - DMA Channel 2
|
|
CONFIG_PIC32MX_DMA3PRIO - DMA Channel 3
|
|
CONFIG_PIC32MX_FCEPRIO - Flash Control Event
|
|
CONFIG_PIC32MX_USBPRIO - USB
|
|
|
|
PIC32MXx specific device driver settings. NOTE: For the Sure board,
|
|
UART2 is brought out to the DB9 connector and serves as the serial
|
|
console.
|
|
|
|
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
|
console and ttys0 (default is the UART0).
|
|
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
|
This specific the size of the receive buffer
|
|
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
|
being sent. This specific the size of the transmit buffer
|
|
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
|
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
CONFIG_UARTn_2STOP - Two stop bits
|
|
|
|
PIC32MXx USB Device Configuration
|
|
|
|
PIC32MXx USB Host Configuration (the PIC32MX does not support USB Host)
|
|
|
|
Configurations
|
|
==============
|
|
|
|
Each PIC32MX configuration is maintained in a sudirectory and can be
|
|
selected as follow:
|
|
|
|
cd tools
|
|
./configure.sh sure-pic32mx/<subdir>
|
|
cd -
|
|
. ./setenv.sh
|
|
|
|
Where <subdir> is one of the following:
|
|
|
|
ostest:
|
|
=======
|
|
Description.
|
|
------------
|
|
This configuration directory, performs a simple OS test using
|
|
apps/examples/ostest.
|
|
|
|
nsh:
|
|
====
|
|
Description.
|
|
------------
|
|
Configures the NuttShell (nsh) located at apps/examples/nsh. The
|
|
Configuration enables only the serial NSH interface.
|
|
|
|
USB Configuations.
|
|
-----------------
|
|
Several USB device configurations can be enabled and included
|
|
as NSH built-in built in functions. All require the following
|
|
basic setup in your .config to enable USB device support:
|
|
|
|
CONFIG_USBDEV=y : Enable basic USB device support
|
|
CONFIG_PIC32MX_USBDEV=y : Enable PIC32 USB device support
|
|
|
|
examples/usbterm - This option can be enabled by uncommenting
|
|
the following line in the appconfig file:
|
|
|
|
CONFIGURED_APPS += examples/usbterm
|
|
|
|
And by enabling one of the USB serial devices:
|
|
|
|
CONFIG_PL2303=y : Enable the Prolifics PL2303 emulation
|
|
CONFIG_CDCACM=y : or the CDC/ACM serial driver (not both)
|
|
|
|
examples/cdcacm - The examples/cdcacm program can be included as an
|
|
function by uncommenting the following line in the appconfig file:
|
|
|
|
CONFIGURED_APPS += examples/cdcacm
|
|
|
|
and defining the following in your .config file:
|
|
|
|
CONFIG_CDCACM=y : Enable the CDCACM device
|
|
|
|
examples/usbstorage - There are some hooks in the appconfig file
|
|
to enable the USB mass storage device. However, this device cannot
|
|
work until support for the SD card is also incorporated.
|
|
|
|
SD Card Support.
|
|
----------------
|
|
Support for the on-board, SPI-based SD card is available but is
|
|
not yet functional (at least at the time of this writing). SD
|
|
card support can be enabled for testing by simply enabling SPI2
|
|
support in the configuration file:
|
|
|
|
-CONFIG_PIC32MX_SPI2=n
|
|
+CONFIG_PIC32MX_SPI2=y
|
|
|
|
Debug output for testing the SD card can be enabled using:
|
|
|
|
-CONFIG_DEBUG_FS=n
|
|
-CONFIG_DEBUG_SPI=n
|
|
+CONFIG_DEBUG_FS=y
|
|
+CONFIG_DEBUG_SPI=y
|
|
|
|
usbnsh:
|
|
=======
|
|
Description.
|
|
------------
|
|
This is another NSH example. If differs from the 'nsh' configuration
|
|
above in that this configurations uses a USB serial device for console
|
|
I/O. This configuration was created to support the "DB-DP11212 PIC32
|
|
General Purpose Demo Board" which has no easily accessible serial port.
|
|
However, as of this writing, the configuration has set for the
|
|
"DB_DP11215 PIC32 Storage Demo Board" and has only be testing on that
|
|
board.
|
|
|
|
Comparison to nsh
|
|
-----------------
|
|
Below summarizes the key configuration differences between the 'nsh'
|
|
and the 'upnsh' configurations:
|
|
|
|
CONFIG_USBDEV=y : NuttX USB device support is enabled
|
|
CONFIG_PIC32MX_USBDEV=y : The PIC32MX USB device driver is built
|
|
CONFIG_UART1_SERIAL_CONSOLE=n : There is no serial console
|
|
CONFIG_UART2_SERIAL_CONSOLE=n :
|
|
CONFIG_CDCACM=y : The CDC/ACM serial device class is enabled
|
|
CONFIG_CDCACM_CONSOLE=y : The CDC/ACM serial device is the console
|
|
|
|
Using the Prolifics PL2303 Emulation
|
|
------------------------------------
|
|
You could also use the non-standard PL2303 serial device instead of
|
|
the standard CDC/ACM serial device by changing:
|
|
|
|
CONFIG_CDCACM=y : Disable the CDC/ACM serial device class
|
|
CONFIG_CDCACM_CONSOLE=y : The CDC/ACM serial device is NOT the console
|
|
CONFIG_PL2303=y : The Prolifics PL2303 emulation is enabled
|
|
CONFIG_PL2303_CONSOLE=y : The PL2303 serial device is the console
|
|
|
|
Why would you want to use a non-standard USB serial driver? You might
|
|
to use the PL2303 driver with a Windows host because it should
|
|
automatically install the PL2303 driver (you might have to go through
|
|
some effort to get Windows to recognize the CDC/ACM device).
|