Adds support for the STM32F103VCT6 and for the Hy-Mini STM32v board. Contributed by Laurent Latil
git-svn-id: https://nuttx.svn.sourceforge.net/svnroot/nuttx/trunk@4197 7fd9a85b-ad96-42d3-883c-3090e2eb8679
This commit is contained in:
parent
e7db4ff53b
commit
10bfc47017
|
@ -2279,4 +2279,7 @@
|
|||
was not correct. However, this driver has functioned for a long time until
|
||||
the particular condition that revealed the bug occurred. My impression is
|
||||
that this latter bugfix also fixes some STM32 USB performance problems.
|
||||
* configs/hymini-stm32v: A configuration for the HY-Mini STM32v board contributed
|
||||
by Laurent Latil. Theses changes also include support for the _STM32F103VCT6.
|
||||
|
||||
|
||||
|
|
|
@ -110,6 +110,33 @@
|
|||
# define STM32_NRNG 0 /* No random number generator (RNG) */
|
||||
# define STM32_NDCMI 0 /* No digital camera interface (DCMI) */
|
||||
|
||||
#elif defined(CONFIG_ARCH_CHIP_STM32F103VCT6)
|
||||
# define CONFIG_STM32_STM32F10XX 1 /* STM32F10xxx family */
|
||||
# undef CONFIG_STM32_LOWDENSITY /* STM32F101x, STM32F102x and STM32F103x w/ 16/32 Kbytes */
|
||||
# undef CONFIG_STM32_MEDIUMDENSITY /* STM32F101x, STM32F102x and STM32F103x w/ 64/128 Kbytes */
|
||||
# define CONFIG_STM32_HIGHDENSITY 1 /* STM32F101x and STM32F103x w/ 256/512 Kbytes */
|
||||
# undef CONFIG_STM32_CONNECTIVITYLINE /* STM32F105x and STM32F107x */
|
||||
# undef CONFIG_STM32_STM32F40XX /* STM32F405xx and STM32407xx families */
|
||||
# define STM32_NFSMC 1 /* FSMC */
|
||||
# define STM32_NATIM 2 /* Two advanced timers TIM1 and TIM8 */
|
||||
# define STM32_NGTIM 4 /* General timers TIM2,3,4,5 */
|
||||
# define STM32_NBTIM 2 /* Two basic timers TIM6 and TIM7 */
|
||||
# define STM32_NDMA 2 /* DMA1-2 */
|
||||
# define STM32_NSPI 3 /* SPI1-3 */
|
||||
# define STM32_NI2S 0 /* No I2S (?) */
|
||||
# define STM32_NUSART 5 /* USART1-5 */
|
||||
# define STM32_NI2C 2 /* I2C1-2 */
|
||||
# define STM32_NCAN 1 /* bxCAN1 */
|
||||
# define STM32_NSDIO 1 /* SDIO */
|
||||
# define STM32_NUSBOTG 0 /* No USB OTG FS/HS */
|
||||
# define STM32_NGPIO 80 /* GPIOA-E */
|
||||
# define STM32_NADC 3 /* ADC1-3 */
|
||||
# define STM32_NDAC 2 /* DAC1-2 */
|
||||
# define STM32_NCRC 1 /* CRC */
|
||||
# define STM32_NTHERNET 0 /* No ethernet */
|
||||
# define STM32_NRNG 0 /* No random number generator (RNG) */
|
||||
# define STM32_NDCMI 0 /* No digital camera interface (DCMI) */
|
||||
|
||||
#elif defined(CONFIG_ARCH_CHIP_STM32F107VC)
|
||||
# define CONFIG_STM32_STM32F10XX 1 /* STM32F10xxx family */
|
||||
# undef CONFIG_STM32_LOWDENSITY /* STM32F101x, STM32F102x and STM32F103x w/ 16/32 Kbytes */
|
||||
|
|
|
@ -53,6 +53,8 @@
|
|||
# include "chip/stm32f103ze_pinmap.h"
|
||||
# elif defined(CONFIG_ARCH_CHIP_STM32F103RET6)
|
||||
# include "chip/stm32f103re_pinmap.h"
|
||||
# elif defined(CONFIG_ARCH_CHIP_STM32F103VCT6)
|
||||
# include "chip/stm32f103vc_pinmap.h"
|
||||
# elif defined(CONFIG_ARCH_CHIP_STM32F107VC)
|
||||
# include "chip/stm32f107vc_pinmap.h"
|
||||
# else
|
||||
|
|
|
@ -905,7 +905,7 @@ static void spi_setmode(FAR struct spi_dev_s *dev, enum spi_mode_e mode)
|
|||
|
||||
spi_modifycr1(priv, setbits, clrbits);
|
||||
|
||||
/* Save the mode so that subsequent re-configuratins will be faster */
|
||||
/* Save the mode so that subsequent re-configurations will be faster */
|
||||
|
||||
#ifndef CONFIG_SPI_OWNBUS
|
||||
priv->mode = mode;
|
||||
|
@ -1102,7 +1102,7 @@ static void spi_exchange(FAR struct spi_dev_s *dev, FAR const void *txbuffer,
|
|||
* dev - Device-specific state data
|
||||
* txbuffer - A pointer to the buffer of data to be sent
|
||||
* rxbuffer - A pointer to a buffer in which to receive data
|
||||
* nwords - the length of data to be exchaned in units of words.
|
||||
* nwords - the length of data to be exchanged in units of words.
|
||||
* The wordsize is determined by the number of bits-per-word
|
||||
* selected for the SPI interface. If nbits <= 8, the data is
|
||||
* packed into uint8_t's; if nbits >8, the data is packed into uint16_t's
|
||||
|
@ -1169,7 +1169,7 @@ static void spi_sndblock(FAR struct spi_dev_s *dev, FAR const void *txbuffer, si
|
|||
* Name: spi_recvblock
|
||||
*
|
||||
* Description:
|
||||
* Revice a block of data from SPI
|
||||
* Receive a block of data from SPI
|
||||
*
|
||||
* Input Parameters:
|
||||
* dev - Device-specific state data
|
||||
|
@ -1295,8 +1295,6 @@ FAR struct spi_dev_s *up_spiinitialize(int port)
|
|||
#ifdef CONFIG_STM32_SPI1
|
||||
if (port == 1)
|
||||
{
|
||||
uint32_t mapr;
|
||||
|
||||
/* Select SPI1 */
|
||||
|
||||
priv = &g_spi1dev;
|
||||
|
|
|
@ -1236,6 +1236,9 @@ configs/ez80f0910200zco
|
|||
development kit, eZ80F091 part, and the Zilog ZDS-II Windows command line
|
||||
tools. The development environment is Cygwin under WinXP.
|
||||
|
||||
configs/hymini-stm32v
|
||||
A configuration for the HY-Mini STM32v board.
|
||||
|
||||
configs/kwikstik-k40.
|
||||
Kinetis K40 Cortex-M4 MCU. This port uses the FreeScale KwikStik-K40
|
||||
development board.
|
||||
|
|
|
@ -0,0 +1,674 @@
|
|||
README
|
||||
======
|
||||
|
||||
This README discusses issues unique to NuttX configurations for the
|
||||
HY-MiniSTM32V development board.
|
||||
|
||||
Contents
|
||||
========
|
||||
|
||||
- Development Environment
|
||||
- GNU Toolchain Options
|
||||
- IDEs
|
||||
- NuttX buildroot Toolchain
|
||||
- DFU
|
||||
- LEDs
|
||||
- RTC
|
||||
- HY-Mini specific Configuration Options
|
||||
- Configurations
|
||||
|
||||
Development Environment
|
||||
=======================
|
||||
|
||||
Either Linux or Cygwin on Windows can be used for the development environment.
|
||||
The source has been built only using the GNU toolchain (see below). Other
|
||||
toolchains will likely cause problems. Testing was performed using the Cygwin
|
||||
environment because the Raisonance R-Link emulatator and some RIDE7 development tools
|
||||
were used and those tools works only under Windows.
|
||||
|
||||
GNU Toolchain Options
|
||||
=====================
|
||||
|
||||
The NuttX make system has been modified to support the following different
|
||||
toolchain options.
|
||||
|
||||
1. The CodeSourcery GNU toolchain,
|
||||
2. The devkitARM GNU toolchain,
|
||||
3. Raisonance GNU toolchain, or
|
||||
4. The NuttX buildroot Toolchain (see below).
|
||||
|
||||
All testing has been conducted using the NuttX buildroot toolchain. However,
|
||||
the make system is setup to default to use the devkitARM toolchain. To use
|
||||
the CodeSourcery, devkitARM or Raisonance GNU toolchain, you simply need to
|
||||
add one of the following configuration options to your .config (or defconfig)
|
||||
file:
|
||||
|
||||
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
|
||||
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux
|
||||
CONFIG_STM32_DEVKITARM=y : devkitARM under Windows
|
||||
CONFIG_STM32_RAISONANCE=y : Raisonance RIDE7 under Windows
|
||||
CONFIG_STM32_BUILDROOT=y : NuttX buildroot under Linux or Cygwin (default)
|
||||
|
||||
If you are not using CONFIG_STM32_BUILDROOT, then you may also have to modify
|
||||
the PATH in the setenv.h file if your make cannot find the tools.
|
||||
|
||||
NOTE: the CodeSourcery (for Windows), devkitARM, and Raisonance toolchains are
|
||||
Windows native toolchains. The CodeSourcey (for Linux) and NuttX buildroot
|
||||
toolchains are Cygwin and/or Linux native toolchains. There are several limitations
|
||||
to using a Windows based toolchain in a Cygwin environment. The three biggest are:
|
||||
|
||||
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
|
||||
performed automatically in the Cygwin makefiles using the 'cygpath' utility
|
||||
but you might easily find some new path problems. If so, check out 'cygpath -w'
|
||||
|
||||
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
|
||||
are used in Nuttx (e.g., include/arch). The make system works around these
|
||||
problems for the Windows tools by copying directories instead of linking them.
|
||||
But this can also cause some confusion for you: For example, you may edit
|
||||
a file in a "linked" directory and find that your changes had no effect.
|
||||
That is because you are building the copy of the file in the "fake" symbolic
|
||||
directory. If you use a Windows toolchain, you should get in the habit of
|
||||
making like this:
|
||||
|
||||
make clean_context all
|
||||
|
||||
An alias in your .bashrc file might make that less painful.
|
||||
|
||||
3. Dependencies are not made when using Windows versions of the GCC. This is
|
||||
because the dependencies are generated using Windows pathes which do not
|
||||
work with the Cygwin make.
|
||||
|
||||
Support has been added for making dependencies with the windows-native toolchains.
|
||||
That support can be enabled by modifying your Make.defs file as follows:
|
||||
|
||||
- MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
+ MKDEP = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
|
||||
|
||||
If you have problems with the dependency build (for example, if you are not
|
||||
building on C:), then you may need to modify tools/mkdeps.sh
|
||||
|
||||
NOTE 1: The CodeSourcery toolchain (2009q1) does not work with default optimization
|
||||
level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with
|
||||
-Os.
|
||||
|
||||
NOTE 2: The devkitARM toolchain includes a version of MSYS make. Make sure that
|
||||
the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
|
||||
path or will get the wrong version of make.
|
||||
|
||||
IDEs
|
||||
====
|
||||
|
||||
NuttX is built using command-line make. It can be used with an IDE, but some
|
||||
effort will be required to create the project (There is a simple RIDE project
|
||||
in the RIDE subdirectory).
|
||||
|
||||
Makefile Build
|
||||
--------------
|
||||
Under Eclipse, it is pretty easy to set up an "empty makefile project" and
|
||||
simply use the NuttX makefile to build the system. That is almost for free
|
||||
under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty
|
||||
makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
|
||||
there is a lot of help on the internet).
|
||||
|
||||
Native Build
|
||||
------------
|
||||
Here are a few tips before you start that effort:
|
||||
|
||||
1) Select the toolchain that you will be using in your .config file
|
||||
2) Start the NuttX build at least one time from the Cygwin command line
|
||||
before trying to create your project. This is necessary to create
|
||||
certain auto-generated files and directories that will be needed.
|
||||
3) Set up include pathes: You will need include/, arch/arm/src/stm32,
|
||||
arch/arm/src/common, arch/arm/src/armv7-m, and sched/.
|
||||
4) All assembly files need to have the definition option -D __ASSEMBLY__
|
||||
on the command line.
|
||||
|
||||
Startup files will probably cause you some headaches. The NuttX startup file
|
||||
is arch/arm/src/stm32/stm32_vectors.S. With RIDE, I have to build NuttX
|
||||
one time from the Cygwin command line in order to obtain the pre-built
|
||||
startup object needed by RIDE.
|
||||
|
||||
NuttX buildroot Toolchain
|
||||
=========================
|
||||
|
||||
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
|
||||
be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
|
||||
different from the default in your PATH variable).
|
||||
|
||||
If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
|
||||
SourceForge download site (https://sourceforge.net/project/showfiles.php?group_id=189573).
|
||||
This GNU toolchain builds and executes in the Linux or Cygwin environment.
|
||||
|
||||
1. You must have already configured Nuttx in <some-dir>/nuttx.
|
||||
|
||||
cd tools
|
||||
./configure.sh hymini-stm32v/<sub-dir>
|
||||
|
||||
2. Download the latest buildroot package into <some-dir>
|
||||
|
||||
3. unpack the buildroot tarball. The resulting directory may
|
||||
have versioning information on it like buildroot-x.y.z. If so,
|
||||
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
|
||||
|
||||
4. cd <some-dir>/buildroot
|
||||
|
||||
5. cp configs/cortexm3-defconfig-4.3.3 .config
|
||||
|
||||
6. make oldconfig
|
||||
|
||||
7. make
|
||||
|
||||
8. Edit setenv.h, if necessary, so that the PATH variable includes
|
||||
the path to the newly built binaries.
|
||||
|
||||
See the file configs/README.txt in the buildroot source tree. That has more
|
||||
detailed PLUS some special instructions that you will need to follow if you are
|
||||
building a Cortex-M3 toolchain for Cygwin under Windows.
|
||||
|
||||
DFU
|
||||
===
|
||||
|
||||
The linker files in these projects can be configured to indicate that you
|
||||
will be loading code using STMicro built-in USB Device Firmware Upgrade (DFU)
|
||||
loader or via some JTAG emulator. You can specify the DFU bootloader by
|
||||
adding the following line:
|
||||
|
||||
CONFIG_STM32_DFU=y
|
||||
|
||||
to your .config file. Most of the configurations in this directory are set
|
||||
up to use the DFU loader.
|
||||
|
||||
If CONFIG_STM32_DFU is defined, the code will not be positioned at the beginning
|
||||
of FLASH (0x08000000) but will be offset to 0x08003000. This offset is needed
|
||||
to make space for the DFU loader and 0x08003000 is where the DFU loader expects
|
||||
to find new applications at boot time. If you need to change that origin for some
|
||||
other bootloader, you will need to edit the file(s) ld.script.dfu for each
|
||||
configuration.
|
||||
|
||||
The DFU SE PC-based software is available from the STMicro website,
|
||||
http://www.st.com. General usage instructions:
|
||||
|
||||
1. Convert the NuttX Intel Hex file (nuttx.ihx) into a special DFU
|
||||
file (nuttx.dfu)... see below for details.
|
||||
2. Connect the Hy-Mini STM32v board to your computer using a USB
|
||||
cable.
|
||||
3. Start the DFU loader on the Hy-Mini STM32v board. You do this by
|
||||
resetting the board while holding the "Key" button. Windows should
|
||||
recognize that the DFU loader has been installed.
|
||||
3. Run the DFU SE program to load nuttx.dfu into FLASH.
|
||||
|
||||
What if the DFU loader is not in FLASH? The loader code is available
|
||||
inside of the Demo dirctory of the USBLib ZIP file that can be downloaded
|
||||
from the STMicro Website. You can build it using RIDE (or other toolchains);
|
||||
you will need a JTAG emulator to burn it into FLASH the first time.
|
||||
|
||||
In order to use STMicro's built-in DFU loader, you will have to get
|
||||
the NuttX binary into a special format with a .dfu extension. The
|
||||
DFU SE PC_based software installation includes a file "DFU File Manager"
|
||||
conversion program that a file in Intel Hex format to the special DFU
|
||||
format. When you successfully build NuttX, you will find a file called
|
||||
nutt.ihx in the top-level directory. That is the file that you should
|
||||
provide to the DFU File Manager. You will need to rename it to nuttx.hex
|
||||
in order to find it with the DFU File Manager. You will end up with
|
||||
a file called nuttx.dfu that you can use with the STMicro DFU SE program.
|
||||
|
||||
LEDs
|
||||
====
|
||||
|
||||
The HY-MiniSTM32 board provides only two controlable LEDs labeled LED1 and LED2.
|
||||
Usage of these LEDs is defined in include/board.h and src/up_leds.c.
|
||||
They are encoded as follows:
|
||||
|
||||
SYMBOL Meaning LED1* LED2
|
||||
------------------- ----------------------- ------- -------
|
||||
LED_STARTED NuttX has been started OFF OFF
|
||||
LED_HEAPALLOCATE Heap has been allocated ON OFF
|
||||
LED_IRQSENABLED Interrupts enabled OFF ON
|
||||
LED_STACKCREATED Idle stack created ON OFF
|
||||
LED_INIRQ In an interrupt** OFF N/C
|
||||
LED_SIGNAL In a signal handler*** N/C ON
|
||||
LED_ASSERTION An assertion failed ON ON
|
||||
LED_PANIC The system has crashed BLINK BLINK
|
||||
LED_IDLE STM32 is is sleep mode (Optional, not used)
|
||||
|
||||
* If Nuttx starts correctly, normal state is to have LED1 on and LED2 off.
|
||||
** LED1 is turned off during interrrupt.
|
||||
*** LED2 is turned on during signal handler.
|
||||
|
||||
RTC
|
||||
===
|
||||
|
||||
The STM32 RTC may configured using the following settings.
|
||||
|
||||
CONFIG_RTC - Enables general support for a hardware RTC. Specific
|
||||
architectures may require other specific settings.
|
||||
CONFIG_RTC_HIRES - The typical RTC keeps time to resolution of 1
|
||||
second, usually supporting a 32-bit time_t value. In this case,
|
||||
the RTC is used to "seed" the normal NuttX timer and the
|
||||
NuttX timer provides for higher resoution time. If CONFIG_RTC_HIRES
|
||||
is enabled in the NuttX configuration, then the RTC provides higher
|
||||
resolution time and completely replaces the system timer for purpose of
|
||||
date and time.
|
||||
CONFIG_RTC_FREQUENCY - If CONFIG_RTC_HIRES is defined, then the
|
||||
frequency of the high resolution RTC must be provided. If CONFIG_RTC_HIRES
|
||||
is not defined, CONFIG_RTC_FREQUENCY is assumed to be one.
|
||||
CONFIG_RTC_ALARM - Enable if the RTC hardware supports setting of an alarm.
|
||||
A callback function will be executed when the alarm goes off
|
||||
|
||||
In hi-res mode, the STM32 RTC operates only at 16384Hz. Overflow interrupts
|
||||
are handled when the 32-bit RTC counter overflows every 3 days and 43 minutes.
|
||||
A BKP register is incremented on each overflow interrupt creating, effectively,
|
||||
a 48-bit RTC counter.
|
||||
|
||||
In the lo-res mode, the RTC operates at 1Hz. Overflow interrupts are not handled
|
||||
(because the next overflow is not expected until the year 2106.
|
||||
|
||||
WARNING: Overflow interrupts are lost whenever the STM32 is powered down. The
|
||||
overflow interrupt may be lost even if the STM32 is powered down only momentarily.
|
||||
Therefore hi-res solution is only useful in systems where the power is always on.
|
||||
|
||||
HY-Mini specific Configuration Options
|
||||
============================================
|
||||
|
||||
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
||||
be set to:
|
||||
|
||||
CONFIG_ARCH=arm
|
||||
|
||||
CONFIG_ARCH_family - For use in C code:
|
||||
|
||||
CONFIG_ARCH_ARM=y
|
||||
|
||||
CONFIG_ARCH_architecture - For use in C code:
|
||||
|
||||
CONFIG_ARCH_CORTEXM3=y
|
||||
|
||||
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||||
|
||||
CONFIG_ARCH_CHIP=stm32
|
||||
|
||||
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
||||
chip:
|
||||
|
||||
CONFIG_ARCH_CHIP_STM32F103VCT6
|
||||
|
||||
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG - Enables special STM32 clock
|
||||
configuration features.
|
||||
|
||||
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG=n
|
||||
|
||||
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
||||
hence, the board that supports the particular chip or SoC.
|
||||
|
||||
CONFIG_ARCH_BOARD=hymini-stm32v (for the HY-Mini development board)
|
||||
|
||||
CONFIG_ARCH_BOARD_name - For use in C code
|
||||
|
||||
CONFIG_ARCH_BOARD_HYMINI_STM32V=y
|
||||
|
||||
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
||||
of delay loops
|
||||
|
||||
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
||||
endian)
|
||||
|
||||
CONFIG_DRAM_SIZE - Describes the installed DRAM (SRAM in this case):
|
||||
|
||||
CONFIG_DRAM_SIZE=0x0000C000 (48Kb)
|
||||
|
||||
CONFIG_DRAM_START - The start address of installed DRAM
|
||||
|
||||
CONFIG_DRAM_START=0x20000000
|
||||
|
||||
CONFIG_DRAM_END - Last address+1 of installed RAM
|
||||
|
||||
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
||||
|
||||
CONFIG_ARCH_IRQPRIO - The STM32F103V supports interrupt prioritization
|
||||
|
||||
CONFIG_ARCH_IRQPRIO=y
|
||||
|
||||
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
||||
have LEDs
|
||||
|
||||
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
||||
stack. If defined, this symbol is the size of the interrupt
|
||||
stack in bytes. If not defined, the user task stacks will be
|
||||
used during interrupt handling.
|
||||
|
||||
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||||
|
||||
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
||||
|
||||
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
||||
cause a 100 second delay during boot-up. This 100 second delay
|
||||
serves no purpose other than it allows you to calibratre
|
||||
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
|
||||
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
|
||||
the delay actually is 100 seconds.
|
||||
|
||||
Individual subsystems can be enabled:
|
||||
AHB
|
||||
---
|
||||
CONFIG_STM32_DMA1
|
||||
CONFIG_STM32_DMA2
|
||||
CONFIG_STM32_CRC
|
||||
CONFIG_STM32_FSMC
|
||||
CONFIG_STM32_SDIO
|
||||
|
||||
APB1
|
||||
----
|
||||
CONFIG_STM32_TIM2
|
||||
CONFIG_STM32_TIM3 (required for PWM control of LCD backlight)
|
||||
CONFIG_STM32_TIM4
|
||||
CONFIG_STM32_TIM5
|
||||
CONFIG_STM32_TIM6
|
||||
CONFIG_STM32_TIM7
|
||||
CONFIG_STM32_WWDG
|
||||
CONFIG_STM32_SPI2
|
||||
CONFIG_STM32_SPI4
|
||||
CONFIG_STM32_USART2
|
||||
CONFIG_STM32_USART3
|
||||
CONFIG_STM32_UART4
|
||||
CONFIG_STM32_UART5
|
||||
CONFIG_STM32_I2C1
|
||||
CONFIG_STM32_I2C2
|
||||
CONFIG_STM32_USB
|
||||
CONFIG_STM32_CAN
|
||||
CONFIG_STM32_BKP
|
||||
CONFIG_STM32_PWR
|
||||
CONFIG_STM32_DAC
|
||||
CONFIG_STM32_USB
|
||||
|
||||
APB2
|
||||
----
|
||||
CONFIG_STM32_ADC1
|
||||
CONFIG_STM32_ADC2
|
||||
CONFIG_STM32_TIM1
|
||||
CONFIG_STM32_SPI1
|
||||
CONFIG_STM32_TIM8
|
||||
CONFIG_STM32_USART1
|
||||
CONFIG_STM32_ADC3
|
||||
|
||||
Timer and I2C devices may need to the following to force power to be applied
|
||||
unconditionally at power up. (Otherwise, the device is powered when it is
|
||||
initialized).
|
||||
|
||||
CONFIG_STM32_FORCEPOWER
|
||||
|
||||
The Timer3 alternate mapping is required for PWM control of LCD backlight
|
||||
|
||||
CONFIG_STM32_TIM3_PARTIAL_REMAP=y
|
||||
|
||||
Timer devices may be used for different purposes. One special purpose is
|
||||
to generate modulated outputs for such things as motor control. If CONFIG_STM32_TIMn
|
||||
is defined (as above) then the following may also be defined to indicate that
|
||||
the timer is intended to be used for pulsed output modulation, ADC conversion,
|
||||
or DAC conversion.
|
||||
|
||||
CONFIG_STM32_TIM1_PWM
|
||||
CONFIG_STM32_TIM2_PWM
|
||||
CONFIG_STM32_TIM3_PWM
|
||||
CONFIG_STM32_TIM4_PWM
|
||||
CONFIG_STM32_TIM5_PWM
|
||||
CONFIG_STM32_TIM6_PWM
|
||||
CONFIG_STM32_TIM7_PWM
|
||||
CONFIG_STM32_TIM8_PWM
|
||||
|
||||
CONFIG_STM32_TIM1_ADC
|
||||
CONFIG_STM32_TIM2_ADC
|
||||
CONFIG_STM32_TIM3_ADC
|
||||
CONFIG_STM32_TIM4_ADC
|
||||
CONFIG_STM32_TIM5_ADC
|
||||
CONFIG_STM32_TIM6_ADC
|
||||
CONFIG_STM32_TIM7_ADC
|
||||
CONFIG_STM32_TIM8_ADC
|
||||
|
||||
CONFIG_STM32_TIM1_DAC
|
||||
CONFIG_STM32_TIM2_DAC
|
||||
CONFIG_STM32_TIM3_DAC
|
||||
CONFIG_STM32_TIM4_DAC
|
||||
CONFIG_STM32_TIM5_DAC
|
||||
CONFIG_STM32_TIM6_DAC
|
||||
CONFIG_STM32_TIM7_DAC
|
||||
CONFIG_STM32_TIM8_DAC
|
||||
|
||||
Others alternate pin mappings available:
|
||||
|
||||
CONFIG_STM32_TIM1_FULL_REMAP
|
||||
CONFIG_STM32_TIM1_PARTIAL_REMAP
|
||||
CONFIG_STM32_TIM2_FULL_REMAP
|
||||
CONFIG_STM32_TIM2_PARTIAL_REMAP_1
|
||||
CONFIG_STM32_TIM2_PARTIAL_REMAP_2
|
||||
CONFIG_STM32_TIM3_FULL_REMAP
|
||||
CONFIG_STM32_TIM3_PARTIAL_REMAP
|
||||
CONFIG_STM32_TIM4_REMAP
|
||||
CONFIG_STM32_USART1_REMAP
|
||||
CONFIG_STM32_USART2_REMAP
|
||||
CONFIG_STM32_USART3_FULL_REMAP
|
||||
CONFIG_STM32_USART3_PARTIAL_REMAP
|
||||
CONFIG_STM32_SPI1_REMAP
|
||||
CONFIG_STM32_SPI3_REMAP
|
||||
CONFIG_STM32_I2C1_REMAP
|
||||
CONFIG_STM32_CAN1_FULL_REMAP
|
||||
CONFIG_STM32_CAN1_PARTIAL_REMAP
|
||||
CONFIG_STM32_CAN2_REMAP
|
||||
|
||||
STM32F103V specific device driver settings
|
||||
|
||||
CONFIG_U[S]ARTn_SERIAL_CONSOLE - selects the USARTn (n=1,2,3) or UART
|
||||
m (m=4,5) for the console and ttys0 (default is the USART1).
|
||||
|
||||
Note: USART1 is connected to a PL2303 serial to USB converter.
|
||||
So USART1 is available through USB port labeled CN3 on the board.
|
||||
|
||||
CONFIG_U[S]ARTn_RXBUFSIZE - Characters are buffered as received.
|
||||
This specific the size of the receive buffer
|
||||
CONFIG_U[S]ARTn_TXBUFSIZE - Characters are buffered before
|
||||
being sent. This specific the size of the transmit buffer
|
||||
CONFIG_U[S]ARTn_BAUD - The configure BAUD of the UART. Must be
|
||||
CONFIG_U[S]ARTn_BITS - The number of bits. Must be either 7 or 8.
|
||||
CONFIG_U[S]ARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
||||
CONFIG_U[S]ARTn_2STOP - Two stop bits
|
||||
|
||||
CONFIG_STM32_SPI_INTERRUPTS - Select to enable interrupt driven SPI
|
||||
support. Non-interrupt-driven, poll-waiting is recommended if the
|
||||
interrupt rate would be to high in the interrupt driven case.
|
||||
CONFIG_STM32_SPI_DMA - Use DMA to improve SPI transfer performance.
|
||||
Cannot be used with CONFIG_STM32_SPI_INTERRUPT.
|
||||
|
||||
CONFIG_SDIO_DMA - Support DMA data transfers. Requires CONFIG_STM32_SDIO
|
||||
and CONFIG_STM32_DMA2.
|
||||
CONFIG_SDIO_PRI - Select SDIO interrupt prority. Default: 128
|
||||
CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority.
|
||||
Default: Medium
|
||||
CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode. Default:
|
||||
4-bit transfer mode.
|
||||
CONFIG_MMCSD_HAVECARDDETECT - Select if SDIO driver card detection
|
||||
is 100% accurate (it is on the HY-MiniSTM32V)
|
||||
|
||||
|
||||
HY-MiniSTM32V LCD Hardware Configuration (SSD1289 controler)
|
||||
|
||||
CONFIG_NX_LCDDRIVER - To be defined to include LCD driver
|
||||
CONFIG_LCD_LANDSCAPE - Define for 320x240 display "landscape"
|
||||
support. In this orientation, the HY-MiniSTM32V's
|
||||
LCD used connector is at the right of the display.
|
||||
Default is this 320x240 "landscape" orientation
|
||||
CONFIG_LCD_PORTRAIT - Define for 240x320 display "portrait"
|
||||
orientation support. In this orientation, the HY-MiniSTM32V's
|
||||
LCD used connector is at the bottom of the display. Default is
|
||||
320x240 "landscape" orientation.
|
||||
CONFIG_LCD_RPORTRAIT - Define for 240x320 display "reverse
|
||||
portrait" orientation support. In this orientation, the
|
||||
HY-MiniSTM32V's LCD used connector is at the top of the display.
|
||||
Default is 320x240 "landscape" orientation.
|
||||
CONFIG_LCD_BACKLIGHT - Define to support an adjustable backlight
|
||||
using timer 3. The granularity of the settings is determined
|
||||
by CONFIG_LCD_MAXPOWER. Requires CONFIG_STM32_TIM3.
|
||||
|
||||
|
||||
Configurations
|
||||
==============
|
||||
|
||||
Each HY-MiniSTM32V configuration is maintained in a sudirectory and
|
||||
can be selected as follow:
|
||||
|
||||
cd tools
|
||||
./configure.sh hymini-stm32v/<subdir>
|
||||
cd -
|
||||
. ./setenv.sh
|
||||
|
||||
Where <subdir> is one of the following:
|
||||
|
||||
buttons:
|
||||
--------
|
||||
|
||||
Uses apps/examples/buttons to exercise HY-MiniSTM32V buttons and
|
||||
button interrupts.
|
||||
|
||||
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux
|
||||
|
||||
nsh and nsh2:
|
||||
------------
|
||||
Configure the NuttShell (nsh) located at examples/nsh.
|
||||
|
||||
Differences between the two NSH configurations:
|
||||
|
||||
=========== ======================= ================================
|
||||
nsh nsh2
|
||||
=========== ======================= ================================
|
||||
Toolchain: Codesourcery for Linux Codesourcery for Linux (1)
|
||||
----------- ----------------------- --------------------------------
|
||||
Loader: ST bootloader ST bootloader
|
||||
----------- ----------------------- --------------------------------
|
||||
Serial Debug output: USART1 Debug output: USART1
|
||||
Console: NSH output: USART1 NSH output: USART1 (3)
|
||||
----------- ----------------------- --------------------------------
|
||||
microSD Yes Yes
|
||||
Support
|
||||
----------- ----------------------- --------------------------------
|
||||
FAT FS CONFIG_FAT_LCNAME=y CONFIG_FAT_LCNAME=y
|
||||
Config CONFIG_FAT_LFN=n CONFIG_FAT_LFN=y (4)
|
||||
----------- ----------------------- --------------------------------
|
||||
LCD Driver No Yes
|
||||
Support
|
||||
----------- ----------------------- --------------------------------
|
||||
RTC Support No Yes
|
||||
----------- ----------------------- --------------------------------
|
||||
Support for No Yes
|
||||
Built-in
|
||||
Apps
|
||||
----------- ----------------------- --------------------------------
|
||||
Built-in None apps/examples/nx
|
||||
Apps apps/examples/nxhello
|
||||
apps/examples/usbstorage (5)
|
||||
apps/examples/buttons
|
||||
apps/examples/nximage
|
||||
=========== ======================= ================================
|
||||
|
||||
(1) You will probably need to modify nsh/setenv.sh or nsh2/setenv.sh
|
||||
to set up the correct PATH variable for whichever toolchain you
|
||||
may use.
|
||||
(2) Since DfuSe is assumed, this configuration may only work under
|
||||
Cygwin without modification.
|
||||
(3) When any other device other than /dev/console is used for a user
|
||||
interface, (1) linefeeds (\n) will not be expanded to carriage return
|
||||
/ linefeeds \r\n). You will need to configure your terminal program
|
||||
to account for this. And (2) input is not automatically echoed so
|
||||
you will have to turn local echo on.
|
||||
(4) Microsoft holds several patents related to the design of
|
||||
long file names in the FAT file system. Please refer to the
|
||||
details in the top-level COPYING file. Please do not use FAT
|
||||
long file name unless you are familiar with these patent issues.
|
||||
(5) When built as an NSH add-on command (CONFIG_EXAMPLES_USBSTRG_BUILTIN=y),
|
||||
Caution should be used to assure that the SD drive is not in use when
|
||||
the USB storage device is configured. Specifically, the SD driver
|
||||
should be unmounted like:
|
||||
|
||||
nsh> mount -t vfat /dev/mmcsd0 /mnt/sdcard # Card is mounted in NSH
|
||||
...
|
||||
nsh> umount /mnd/sdcard # Unmount before connecting USB!!!
|
||||
nsh> msconn # Connect the USB storage device
|
||||
...
|
||||
nsh> msdis # Disconnect USB storate device
|
||||
nsh> mount -t vfat /dev/mmcsd0 /mnt/sdcard # Restore the mount
|
||||
|
||||
Failure to do this could result in corruption of the SD card format.
|
||||
|
||||
nx:
|
||||
---
|
||||
An example using the NuttX graphics system (NX). This example
|
||||
focuses on general window controls, movement, mouse and keyboard
|
||||
input.
|
||||
|
||||
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
|
||||
CONFIG_LCD_RPORTRAIT=y : 240x320 reverse portrait
|
||||
|
||||
nxlines:
|
||||
------
|
||||
Another example using the NuttX graphics system (NX). This
|
||||
example focuses on placing lines on the background in various
|
||||
orientations.
|
||||
|
||||
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux
|
||||
CONFIG_LCD_RPORTRAIT=y : 240x320 reverse portrait
|
||||
|
||||
usbserial:
|
||||
---------
|
||||
This configuration directory exercises the USB serial class
|
||||
driver at examples/usbserial. See examples/README.txt for
|
||||
more information.
|
||||
|
||||
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux
|
||||
|
||||
USB debug output can be enabled as by changing the following
|
||||
settings in the configuration file:
|
||||
|
||||
-CONFIG_DEBUG=n
|
||||
-CONFIG_DEBUG_VERBOSE=n
|
||||
-CONFIG_DEBUG_USB=n
|
||||
+CONFIG_DEBUG=y
|
||||
+CONFIG_DEBUG_VERBOSE=y
|
||||
+CONFIG_DEBUG_USB=y
|
||||
|
||||
-CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
|
||||
-CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
|
||||
-CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
|
||||
-CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
|
||||
-CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
|
||||
+CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=y
|
||||
+CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=y
|
||||
+CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=y
|
||||
+CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=y
|
||||
+CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=y
|
||||
|
||||
By default, the usbserial example uses the Prolific PL2303
|
||||
serial/USB converter emulation. The example can be modified
|
||||
to use the CDC/ACM serial class by making the following changes
|
||||
to the configuration file:
|
||||
|
||||
-CONFIG_USBSER=y
|
||||
+CONFIG_USBSER=n
|
||||
|
||||
-CONFIG_CDCSER=n
|
||||
+CONFIG_CDCSER=y
|
||||
|
||||
The example can also be converted to use the alternative
|
||||
USB serial example at apps/examples/usbterm by changing the
|
||||
following:
|
||||
|
||||
-CONFIGURED_APPS += examples/usbserial
|
||||
+CONFIGURED_APPS += examples/usbterm
|
||||
|
||||
In either the original appconfig file (before configuring)
|
||||
or in the final apps/.config file (after configuring).
|
||||
|
||||
usbstorage:
|
||||
----------
|
||||
This configuration directory exercises the USB mass storage
|
||||
class driver at examples/usbstorage. See examples/README.txt for
|
||||
more information.
|
||||
|
||||
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux
|
||||
|
|
@ -0,0 +1,174 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/buttons/Make.defs
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include ${TOPDIR}/.config
|
||||
|
||||
# Setup for the selected toolchain
|
||||
|
||||
ifeq ($(CONFIG_STM32_DFU),y)
|
||||
LDSCRIPT = ld.script.dfu
|
||||
else
|
||||
LDSCRIPT = ld.script
|
||||
endif
|
||||
|
||||
ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
|
||||
# CodeSourcery under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
|
||||
# CodeSourcery under Linux
|
||||
CROSSDEV = arm-none-eabi-
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -O2
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_DEVKITARM),y)
|
||||
# devkitARM under Windows
|
||||
CROSSDEV = arm-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_RAISONANCE),y)
|
||||
# Raisonance RIDE7 under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_BUILDROOT),y)
|
||||
# NuttX buildroot under Linux or Cygwin
|
||||
CROSSDEV = arm-elf-
|
||||
ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -Os
|
||||
endif
|
||||
|
||||
ifeq ($(WINTOOL),y)
|
||||
# Windows-native toolchains
|
||||
DIRLINK = $(TOPDIR)/tools/winlink.sh
|
||||
DIRUNLINK = $(TOPDIR)/tools/unlink.sh
|
||||
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
|
||||
ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/buttons/$(LDSCRIPT)}"
|
||||
MAXOPTIMIZATION = -O2
|
||||
else
|
||||
# Linux/Cygwin-native toolchain
|
||||
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
||||
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
||||
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/buttons/$(LDSCRIPT)
|
||||
endif
|
||||
|
||||
CC = $(CROSSDEV)gcc
|
||||
CXX = $(CROSSDEV)g++
|
||||
CPP = $(CROSSDEV)gcc -E
|
||||
LD = $(CROSSDEV)ld
|
||||
AR = $(CROSSDEV)ar rcs
|
||||
NM = $(CROSSDEV)nm
|
||||
OBJCOPY = $(CROSSDEV)objcopy
|
||||
OBJDUMP = $(CROSSDEV)objdump
|
||||
|
||||
ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
|
||||
ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
|
||||
|
||||
ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
|
||||
ARCHOPTIMIZATION = -g
|
||||
else
|
||||
ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
|
||||
endif
|
||||
|
||||
ARCHCFLAGS = -fno-builtin
|
||||
ARCHCXXFLAGS = -fno-builtin -fno-exceptions
|
||||
ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
|
||||
ARCHWARNINGSXX = -Wall -Wshadow
|
||||
ARCHDEFINES =
|
||||
ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
|
||||
|
||||
CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
|
||||
CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
|
||||
CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
|
||||
AFLAGS = $(CFLAGS) -D__ASSEMBLY__
|
||||
|
||||
NXFLATLDFLAGS1 = -r -d -warn-common
|
||||
NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
|
||||
LDNXFLATFLAGS = -e main -s 2048
|
||||
|
||||
OBJEXT = .o
|
||||
LIBEXT = .a
|
||||
EXEEXT =
|
||||
|
||||
ifneq ($(CROSSDEV),arm-elf-)
|
||||
LDFLAGS += -nostartfiles -nodefaultlibs
|
||||
endif
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
LDFLAGS += -g
|
||||
endif
|
||||
|
||||
define PREPROCESS
|
||||
@echo "CPP: $1->$2"
|
||||
@$(CPP) $(CPPFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILE
|
||||
@echo "CC: $1"
|
||||
@$(CC) -c $(CFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILEXX
|
||||
@echo "CXX: $1"
|
||||
@$(CXX) -c $(CXXFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ASSEMBLE
|
||||
@echo "AS: $1"
|
||||
@$(CC) -c $(AFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ARCHIVE
|
||||
echo "AR: $2"; \
|
||||
$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
|
||||
endef
|
||||
|
||||
define CLEAN
|
||||
@rm -f *.o *.a
|
||||
endef
|
||||
|
||||
HOSTCC = gcc
|
||||
HOSTINCLUDES = -I.
|
||||
HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
|
||||
HOSTLDFLAGS =
|
||||
|
|
@ -0,0 +1,39 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/buttons/appconfig
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
# Path to example in apps/examples containing the user_start entry point
|
||||
|
||||
CONFIGURED_APPS += examples/buttons
|
||||
|
|
@ -0,0 +1,880 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/buttons/defconfig
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
#
|
||||
# architecture selection
|
||||
#
|
||||
# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
|
||||
# processor architecture.
|
||||
# CONFIG_ARCH_family - for use in C code. This identifies the
|
||||
# particular chip family that the architecture is implemented
|
||||
# in.
|
||||
# CONFIG_ARCH_architecture - for use in C code. This identifies the
|
||||
# specific architecture within the chip familyl.
|
||||
# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||||
# CONFIG_ARCH_CHIP_name - For use in C code
|
||||
# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
|
||||
# the board that supports the particular chip or SoC.
|
||||
# CONFIG_ARCH_BOARD_name - for use in C code
|
||||
# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
|
||||
# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
|
||||
# CONFIG_DRAM_SIZE - Describes the installed DRAM.
|
||||
# CONFIG_DRAM_START - The start address of DRAM (physical)
|
||||
# CONFIG_DRAM_END - Last address+1 of installed RAM
|
||||
# CONFIG_ARCH_IRQPRIO - The ST32F103Z supports interrupt prioritization
|
||||
# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
||||
# stack. If defined, this symbol is the size of the interrupt
|
||||
# stack in bytes. If not defined, the user task stacks will be
|
||||
# used during interrupt handling.
|
||||
# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||||
# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
|
||||
# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
||||
# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture.
|
||||
# CONFIG_ARCH_IRQBUTTONS - Must be defined for interrupting button support
|
||||
# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
||||
# cause a 100 second delay during boot-up. This 100 second delay
|
||||
# serves no purpose other than it allows you to calibrate
|
||||
# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure
|
||||
# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
|
||||
# the delay actually is 100 seconds.
|
||||
# CONFIG_ARCH_DMA - Support DMA initialization
|
||||
#
|
||||
CONFIG_ARCH=arm
|
||||
CONFIG_ARCH_ARM=y
|
||||
CONFIG_ARCH_CORTEXM3=y
|
||||
CONFIG_ARCH_CHIP=stm32
|
||||
CONFIG_ARCH_CHIP_STM32F103VCT6=y
|
||||
CONFIG_ARCH_BOARD=hymini-stm32v
|
||||
CONFIG_ARCH_BOARD_HYMINI_STM32V=y
|
||||
CONFIG_BOARD_LOOPSPERMSEC=5483
|
||||
CONFIG_DRAM_SIZE=0x0000C000
|
||||
CONFIG_DRAM_START=0x20000000
|
||||
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
||||
CONFIG_ARCH_IRQPRIO=y
|
||||
CONFIG_ARCH_INTERRUPTSTACK=n
|
||||
CONFIG_ARCH_STACKDUMP=y
|
||||
CONFIG_ARCH_BOOTLOADER=n
|
||||
CONFIG_ARCH_LEDS=y
|
||||
CONFIG_ARCH_BUTTONS=y
|
||||
CONFIG_ARCH_IRQBUTTONS=y
|
||||
CONFIG_ARCH_CALIBRATION=n
|
||||
CONFIG_ARCH_DMA=y
|
||||
|
||||
#
|
||||
# Identify toolchain and linker options
|
||||
#
|
||||
CONFIG_STM32_CODESOURCERYW=n
|
||||
CONFIG_STM32_CODESOURCERYL=y
|
||||
CONFIG_STM32_DEVKITARM=n
|
||||
CONFIG_STM32_RAISONANCE=n
|
||||
CONFIG_STM32_BUILDROOT=n
|
||||
CONFIG_STM32_DFU=n
|
||||
|
||||
#
|
||||
# Individual subsystems can be enabled:
|
||||
#
|
||||
# Individual subsystems can be enabled:
|
||||
# AHB:
|
||||
CONFIG_STM32_DMA1=n
|
||||
CONFIG_STM32_DMA2=n
|
||||
CONFIG_STM32_CRC=n
|
||||
CONFIG_STM32_FSMC=y
|
||||
CONFIG_STM32_SDIO=n
|
||||
# APB1:
|
||||
CONFIG_STM32_TIM2=n
|
||||
CONFIG_STM32_TIM3=n
|
||||
CONFIG_STM32_TIM4=n
|
||||
CONFIG_STM32_TIM5=n
|
||||
CONFIG_STM32_TIM6=n
|
||||
CONFIG_STM32_TIM7=n
|
||||
CONFIG_STM32_WWDG=n
|
||||
CONFIG_STM32_SPI2=n
|
||||
CONFIG_STM32_SPI4=n
|
||||
CONFIG_STM32_USART2=y
|
||||
CONFIG_STM32_USART3=n
|
||||
CONFIG_STM32_UART4=n
|
||||
CONFIG_STM32_UART5=n
|
||||
CONFIG_STM32_I2C1=n
|
||||
CONFIG_STM32_I2C2=n
|
||||
CONFIG_STM32_USB=y
|
||||
CONFIG_STM32_CAN=n
|
||||
CONFIG_STM32_BKP=n
|
||||
CONFIG_STM32_PWR=n
|
||||
CONFIG_STM32_DAC=n
|
||||
# APB2:
|
||||
CONFIG_STM32_ADC1=n
|
||||
CONFIG_STM32_ADC2=n
|
||||
CONFIG_STM32_TIM1=n
|
||||
CONFIG_STM32_SPI1=n
|
||||
CONFIG_STM32_TIM8=n
|
||||
CONFIG_STM32_USART1=y
|
||||
CONFIG_STM32_ADC3=n
|
||||
|
||||
#
|
||||
# Timer and I2C devices may need to the following to force power to be applied:
|
||||
#
|
||||
#CONFIG_STM32_FORCEPOWER=y
|
||||
|
||||
#
|
||||
# STM32F103Z specific serial device driver settings
|
||||
#
|
||||
# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
|
||||
# console and ttys0 (default is the USART1).
|
||||
# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
|
||||
# This specific the size of the receive buffer
|
||||
# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
|
||||
# being sent. This specific the size of the transmit buffer
|
||||
# CONFIG_USARTn_BAUD - The configure BAUD of the UART. Must be
|
||||
# CONFIG_USARTn_BITS - The number of bits. Must be either 7 or 8.
|
||||
# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
||||
# CONFIG_USARTn_2STOP - Two stop bits
|
||||
#
|
||||
CONFIG_USART1_SERIAL_CONSOLE=y
|
||||
CONFIG_USART2_SERIAL_CONSOLE=n
|
||||
CONFIG_USART3_SERIAL_CONSOLE=n
|
||||
CONFIG_USART4_SERIAL_CONSOLE=n
|
||||
CONFIG_USART5_SERIAL_CONSOLE=n
|
||||
|
||||
CONFIG_USART1_TXBUFSIZE=256
|
||||
CONFIG_USART2_TXBUFSIZE=256
|
||||
CONFIG_USART3_TXBUFSIZE=256
|
||||
CONFIG_USART4_TXBUFSIZE=256
|
||||
CONFIG_USART5_TXBUFSIZE=256
|
||||
|
||||
CONFIG_USART1_RXBUFSIZE=256
|
||||
CONFIG_USART2_RXBUFSIZE=256
|
||||
CONFIG_USART3_RXBUFSIZE=256
|
||||
CONFIG_USART4_RXBUFSIZE=256
|
||||
CONFIG_USART5_RXBUFSIZE=256
|
||||
|
||||
CONFIG_USART1_BAUD=115200
|
||||
CONFIG_USART2_BAUD=115200
|
||||
CONFIG_USART3_BAUD=115200
|
||||
CONFIG_USART4_BAUD=115200
|
||||
CONFIG_USART5_BAUD=115200
|
||||
|
||||
CONFIG_USART1_BITS=8
|
||||
CONFIG_USART2_BITS=8
|
||||
CONFIG_USART3_BITS=8
|
||||
CONFIG_USART4_BITS=8
|
||||
CONFIG_USART5_BITS=8
|
||||
|
||||
CONFIG_USART1_PARITY=0
|
||||
CONFIG_USART2_PARITY=0
|
||||
CONFIG_USART3_PARITY=0
|
||||
CONFIG_USART4_PARITY=0
|
||||
CONFIG_USART5_PARITY=0
|
||||
|
||||
CONFIG_USART1_2STOP=0
|
||||
CONFIG_USART2_2STOP=0
|
||||
CONFIG_USART3_2STOP=0
|
||||
CONFIG_USART4_2STOP=0
|
||||
CONFIG_USART5_2STOP=0
|
||||
|
||||
#
|
||||
# STM32F103Z specific SSI device driver settings
|
||||
#
|
||||
# CONFIG_SSIn_DISABLE - select to disable all support for
|
||||
# the SSI
|
||||
# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
|
||||
# Poll-waiting is recommended if the interrupt rate would be to
|
||||
# high in the interrupt driven case.
|
||||
# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
|
||||
# emptying the Rx FIFO. If the SPI frequency is high and this
|
||||
# value is large, then larger values of this setting may cause
|
||||
# Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
|
||||
#
|
||||
CONFIG_SSI0_DISABLE=y
|
||||
CONFIG_SSI1_DISABLE=y
|
||||
CONFIG_SSI_POLLWAIT=y
|
||||
#CONFIG_SSI_TXLIMIT=4
|
||||
|
||||
#
|
||||
# General build options
|
||||
#
|
||||
# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
|
||||
# BSPs from www.ridgerun.com using the tools/mkimage.sh script
|
||||
# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_RAW_BINARY - make a raw binary format file used with many
|
||||
# different loaders using the GNU objcopy program. This option
|
||||
# should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_HAVE_LIBM - toolchain supports libm.a
|
||||
#
|
||||
CONFIG_RRLOAD_BINARY=n
|
||||
CONFIG_INTELHEX_BINARY=y
|
||||
CONFIG_MOTOROLA_SREC=n
|
||||
CONFIG_RAW_BINARY=n
|
||||
CONFIG_HAVE_LIBM=n
|
||||
|
||||
#
|
||||
# General OS setup
|
||||
#
|
||||
# CONFIG_APPS_DIR - Identifies the relative path to the directory
|
||||
# that builds the application to link with NuttX. Default: ../apps
|
||||
# CONFIG_DEBUG - enables built-in debug options
|
||||
# CONFIG_DEBUG_VERBOSE - enables verbose debug output
|
||||
# CONFIG_DEBUG_SYMBOLS - build without optimization and with
|
||||
# debug symbols (needed for use with a debugger).
|
||||
# CONFIG_MM_REGIONS - If the architecture includes multiple
|
||||
# regions of memory to allocate from, this specifies the
|
||||
# number of memory regions that the memory manager must
|
||||
# handle and enables the API mm_addregion(start, end);
|
||||
# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
|
||||
# time console output
|
||||
# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
|
||||
# or MSEC_PER_TICK=10. This setting may be defined to
|
||||
# inform NuttX that the processor hardware is providing
|
||||
# system timer interrupts at some interrupt interval other
|
||||
# than 10 msec.
|
||||
# CONFIG_RR_INTERVAL - The round robin timeslice will be set
|
||||
# this number of milliseconds; Round robin scheduling can
|
||||
# be disabled by setting this value to zero.
|
||||
# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in
|
||||
# scheduler to monitor system performance
|
||||
# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
|
||||
# task name to save in the TCB. Useful if scheduler
|
||||
# instrumentation is selected. Set to zero to disable.
|
||||
# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
|
||||
# Used to initialize the internal time logic.
|
||||
# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
|
||||
# You would only need this if you are concerned about accurate
|
||||
# time conversions in the past or in the distant future.
|
||||
# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
|
||||
# would only need this if you are concerned about accurate
|
||||
# time conversion in the distand past. You must also define
|
||||
# CONFIG_GREGORIAN_TIME in order to use Julian time.
|
||||
# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
|
||||
# provides /dev/console. Enables stdout, stderr, stdin.
|
||||
# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
|
||||
# driver (minimul support)
|
||||
# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
|
||||
# errorcheck mutexes. Enables pthread_mutexattr_settype().
|
||||
# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
|
||||
# inheritance on mutexes and semaphores.
|
||||
# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
|
||||
# inheritance is enabled. It defines the maximum number of
|
||||
# different threads (minus one) that can take counts on a
|
||||
# semaphore with priority inheritance support. This may be
|
||||
# set to zero if priority inheritance is disabled OR if you
|
||||
# are only using semaphores as mutexes (only one holder) OR
|
||||
# if no more than two threads participate using a counting
|
||||
# semaphore.
|
||||
# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled,
|
||||
# then this setting is the maximum number of higher priority
|
||||
# threads (minus 1) than can be waiting for another thread
|
||||
# to release a count on a semaphore. This value may be set
|
||||
# to zero if no more than one thread is expected to wait for
|
||||
# a semaphore.
|
||||
# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
|
||||
# by task_create() when a new task is started. If set, all
|
||||
# files/drivers will appear to be closed in the new task.
|
||||
# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
|
||||
# three file descriptors (stdin, stdout, stderr) by task_create()
|
||||
# when a new task is started. If set, all files/drivers will
|
||||
# appear to be closed in the new task except for stdin, stdout,
|
||||
# and stderr.
|
||||
# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
|
||||
# desciptors by task_create() when a new task is started. If
|
||||
# set, all sockets will appear to be closed in the new task.
|
||||
# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
|
||||
# This format will support execution of NuttX binaries located
|
||||
# in a ROMFS filesystem (see examples/nxflat).
|
||||
# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to
|
||||
# handle delayed processing from interrupt handlers. This feature
|
||||
# is required for some drivers but, if there are not complaints,
|
||||
# can be safely disabled. The worker thread also performs
|
||||
# garbage collection -- completing any delayed memory deallocations
|
||||
# from interrupt handlers. If the worker thread is disabled,
|
||||
# then that clean will be performed by the IDLE thread instead
|
||||
# (which runs at the lowest of priority and may not be appropriate
|
||||
# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE
|
||||
# is enabled, then the following options can also be used:
|
||||
# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
|
||||
# thread. Default: 50
|
||||
# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
|
||||
# work in units of microseconds. Default: 50*1000 (50 MS).
|
||||
# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
|
||||
# thread. Default: CONFIG_IDLETHREAD_STACKSIZE.
|
||||
# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
|
||||
# the worker thread. Default: 4
|
||||
#
|
||||
#CONFIG_APPS_DIR=
|
||||
CONFIG_DEBUG=n
|
||||
CONFIG_DEBUG_VERBOSE=n
|
||||
CONFIG_DEBUG_SYMBOLS=n
|
||||
CONFIG_MM_REGIONS=1
|
||||
CONFIG_ARCH_LOWPUTC=y
|
||||
CONFIG_RR_INTERVAL=200
|
||||
CONFIG_SCHED_INSTRUMENTATION=n
|
||||
CONFIG_TASK_NAME_SIZE=0
|
||||
CONFIG_START_YEAR=2011
|
||||
CONFIG_START_MONTH=7
|
||||
CONFIG_START_DAY=7
|
||||
CONFIG_GREGORIAN_TIME=n
|
||||
CONFIG_JULIAN_TIME=n
|
||||
CONFIG_DEV_CONSOLE=y
|
||||
CONFIG_DEV_LOWCONSOLE=y
|
||||
CONFIG_MUTEX_TYPES=n
|
||||
CONFIG_PRIORITY_INHERITANCE=n
|
||||
CONFIG_SEM_PREALLOCHOLDERS=0
|
||||
CONFIG_SEM_NNESTPRIO=0
|
||||
CONFIG_FDCLONE_DISABLE=n
|
||||
CONFIG_FDCLONE_STDIO=n
|
||||
CONFIG_SDCLONE_DISABLE=y
|
||||
CONFIG_NXFLAT=n
|
||||
CONFIG_SCHED_WORKQUEUE=n
|
||||
CONFIG_SCHED_WORKPRIORITY=50
|
||||
CONFIG_SCHED_WORKPERIOD=(50*1000)
|
||||
CONFIG_SCHED_WORKSTACKSIZE=1024
|
||||
CONFIG_SIG_SIGWORK=4
|
||||
|
||||
#
|
||||
# The following can be used to disable categories of
|
||||
# APIs supported by the OS. If the compiler supports
|
||||
# weak functions, then it should not be necessary to
|
||||
# disable functions unless you want to restrict usage
|
||||
# of those APIs.
|
||||
#
|
||||
# There are certain dependency relationships in these
|
||||
# features.
|
||||
#
|
||||
# o mq_notify logic depends on signals to awaken tasks
|
||||
# waiting for queues to become full or empty.
|
||||
# o pthread_condtimedwait() depends on signals to wake
|
||||
# up waiting tasks.
|
||||
#
|
||||
CONFIG_DISABLE_CLOCK=n
|
||||
CONFIG_DISABLE_POSIX_TIMERS=y
|
||||
CONFIG_DISABLE_PTHREAD=y
|
||||
CONFIG_DISABLE_SIGNALS=n
|
||||
CONFIG_DISABLE_MQUEUE=y
|
||||
CONFIG_DISABLE_MOUNTPOINT=y
|
||||
CONFIG_DISABLE_ENVIRON=y
|
||||
CONFIG_DISABLE_POLL=y
|
||||
|
||||
#
|
||||
# Misc libc settings
|
||||
#
|
||||
# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
|
||||
# little smaller if we do not support fieldwidthes
|
||||
#
|
||||
CONFIG_NOPRINTF_FIELDWIDTH=n
|
||||
|
||||
#
|
||||
# Allow for architecture optimized implementations
|
||||
#
|
||||
# The architecture can provide optimized versions of the
|
||||
# following to improve system performance
|
||||
#
|
||||
CONFIG_ARCH_MEMCPY=n
|
||||
CONFIG_ARCH_MEMCMP=n
|
||||
CONFIG_ARCH_MEMMOVE=n
|
||||
CONFIG_ARCH_MEMSET=n
|
||||
CONFIG_ARCH_STRCMP=n
|
||||
CONFIG_ARCH_STRCPY=n
|
||||
CONFIG_ARCH_STRNCPY=n
|
||||
CONFIG_ARCH_STRLEN=n
|
||||
CONFIG_ARCH_STRNLEN=n
|
||||
CONFIG_ARCH_BZERO=n
|
||||
|
||||
#
|
||||
# Sizes of configurable things (0 disables)
|
||||
#
|
||||
# CONFIG_MAX_TASKS - The maximum number of simultaneously
|
||||
# active tasks. This value must be a power of two.
|
||||
# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
|
||||
# of parameters that a task may receive (i.e., maxmum value
|
||||
# of 'argc')
|
||||
# CONFIG_NPTHREAD_KEYS - The number of items of thread-
|
||||
# specific data that can be retained
|
||||
# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
|
||||
# descriptors (one for each open)
|
||||
# CONFIG_NFILE_STREAMS - The maximum number of streams that
|
||||
# can be fopen'ed
|
||||
# CONFIG_NAME_MAX - The maximum size of a file name.
|
||||
# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
|
||||
# on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_NUNGET_CHARS - Number of characters that can be
|
||||
# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
|
||||
# structures. The system manages a pool of preallocated
|
||||
# message structures to minimize dynamic allocations
|
||||
# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
|
||||
# a fixed payload size given by this settin (does not include
|
||||
# other message structure overhead.
|
||||
# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
|
||||
# can be passed to a watchdog handler
|
||||
# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
|
||||
# structures. The system manages a pool of preallocated
|
||||
# watchdog structures to minimize dynamic allocations
|
||||
# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
|
||||
# timer structures. The system manages a pool of preallocated
|
||||
# timer structures to minimize dynamic allocations. Set to
|
||||
# zero for all dynamic allocations.
|
||||
#
|
||||
CONFIG_MAX_TASKS=8
|
||||
CONFIG_MAX_TASK_ARGS=4
|
||||
CONFIG_NPTHREAD_KEYS=4
|
||||
CONFIG_NFILE_DESCRIPTORS=6
|
||||
CONFIG_NFILE_STREAMS=6
|
||||
CONFIG_NAME_MAX=32
|
||||
CONFIG_STDIO_BUFFER_SIZE=64
|
||||
CONFIG_STDIO_LINEBUFFER=y
|
||||
CONFIG_NUNGET_CHARS=2
|
||||
CONFIG_PREALLOC_MQ_MSGS=4
|
||||
CONFIG_MQ_MAXMSGSIZE=32
|
||||
CONFIG_MAX_WDOGPARMS=2
|
||||
CONFIG_PREALLOC_WDOGS=4
|
||||
CONFIG_PREALLOC_TIMERS=4
|
||||
|
||||
#
|
||||
# Filesystem configuration
|
||||
#
|
||||
# CONFIG_FS_FAT - Enable FAT filesystem support
|
||||
# CONFIG_FAT_SECTORSIZE - Max supported sector size
|
||||
# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
|
||||
# file name support.
|
||||
# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims
|
||||
# patents on FAT long file name technology. Please read the
|
||||
# disclaimer in the top-level COPYING file and only enable this
|
||||
# feature if you understand these issues.
|
||||
# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
|
||||
# default, maximum long file name is 255 bytes. This can eat up
|
||||
# a lot of memory (especially stack space). If you are willing
|
||||
# to live with some non-standard, short long file names, then
|
||||
# define this value. A good choice would be the same value as
|
||||
# selected for CONFIG_NAME_MAX which will limit the visibility
|
||||
# of longer file names anyway.
|
||||
# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
|
||||
# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH.
|
||||
# This must have one of the values of 0xff or 0x00.
|
||||
# Default: 0xff.
|
||||
# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
|
||||
# don't both with file chunks smaller than this number of data bytes.
|
||||
# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
|
||||
# Default: 255.
|
||||
# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
|
||||
# don't both with file chunks smaller than this number of data bytes.
|
||||
# Default: 32.
|
||||
# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
|
||||
# packing files together toward the end of the file or, if file are
|
||||
# deleted at the end of the file, clean up can simply mean erasing
|
||||
# the end of FLASH memory so that it can be re-used again. However,
|
||||
# doing this can also harm the life of the FLASH part because it can
|
||||
# mean that the tail end of the FLASH is re-used too often. This
|
||||
# threshold determines if/when it is worth erased the tail end of FLASH
|
||||
# and making it available for re-use (and possible over-wear).
|
||||
# Default: 8192.
|
||||
# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
|
||||
# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
|
||||
# option will enable a limited form of memory mapping that is
|
||||
# implemented by copying whole files into memory.
|
||||
#
|
||||
CONFIG_FS_FAT=n
|
||||
CONFIG_FAT_LCNAMES=n
|
||||
CONFIG_FAT_LFN=n
|
||||
CONFIG_FAT_MAXFNAME=32
|
||||
CONFIG_FS_NXFFS=n
|
||||
CONFIG_FS_ROMFS=n
|
||||
|
||||
#
|
||||
# SPI-based MMC/SD driver
|
||||
#
|
||||
# CONFIG_MMCSD_NSLOTS
|
||||
# Number of MMC/SD slots supported by the driver
|
||||
# CONFIG_MMCSD_READONLY
|
||||
# Provide read-only access (default is read/write)
|
||||
# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
|
||||
# Default is 20MHz.
|
||||
#
|
||||
CONFIG_MMCSD_NSLOTS=1
|
||||
CONFIG_MMCSD_READONLY=n
|
||||
CONFIG_MMCSD_SPICLOCK=12500000
|
||||
|
||||
#
|
||||
# Block driver buffering
|
||||
#
|
||||
# CONFIG_FS_READAHEAD
|
||||
# Enable read-ahead buffering
|
||||
# CONFIG_FS_WRITEBUFFER
|
||||
# Enable write buffering
|
||||
#
|
||||
CONFIG_FS_READAHEAD=n
|
||||
CONFIG_FS_WRITEBUFFER=n
|
||||
|
||||
#
|
||||
# SDIO-based MMC/SD driver
|
||||
#
|
||||
# CONFIG_SDIO_DMA
|
||||
# SDIO driver supports DMA
|
||||
# CONFIG_MMCSD_MMCSUPPORT
|
||||
# Enable support for MMC cards
|
||||
# CONFIG_MMCSD_HAVECARDDETECT
|
||||
# SDIO driver card detection is 100% accurate
|
||||
#
|
||||
CONFIG_SDIO_DMA=n
|
||||
CONFIG_MMCSD_MMCSUPPORT=n
|
||||
CONFIG_MMCSD_HAVECARDDETECT=n
|
||||
|
||||
#
|
||||
# TCP/IP and UDP support via uIP
|
||||
# CONFIG_NET - Enable or disable all network features
|
||||
# CONFIG_NET_IPv6 - Build in support for IPv6
|
||||
# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
|
||||
# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
|
||||
# CONFIG_NET_BUFSIZE - uIP buffer size
|
||||
# CONFIG_NET_TCP - TCP support on or off
|
||||
# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
|
||||
# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
|
||||
# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
|
||||
# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
|
||||
# accept() is called. The size of the backlog is selected when listen() is called.
|
||||
# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
|
||||
# CONFIG_NET_UDP - UDP support on or off
|
||||
# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
|
||||
# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
|
||||
# CONFIG_NET_ICMP - ICMP ping response support on or off
|
||||
# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
|
||||
# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
|
||||
# CONFIG_NET_STATISTICS - uIP statistics on or off
|
||||
# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
|
||||
# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
|
||||
# CONFIG_NET_BROADCAST - Broadcast support
|
||||
# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
|
||||
#
|
||||
CONFIG_NET=n
|
||||
CONFIG_NET_IPv6=n
|
||||
CONFIG_NSOCKET_DESCRIPTORS=0
|
||||
CONFIG_NET_SOCKOPTS=y
|
||||
CONFIG_NET_BUFSIZE=420
|
||||
CONFIG_NET_TCP=n
|
||||
CONFIG_NET_TCP_CONNS=40
|
||||
CONFIG_NET_MAX_LISTENPORTS=40
|
||||
CONFIG_NET_UDP=n
|
||||
CONFIG_NET_UDP_CHECKSUMS=y
|
||||
#CONFIG_NET_UDP_CONNS=10
|
||||
CONFIG_NET_ICMP=n
|
||||
CONFIG_NET_ICMP_PING=n
|
||||
#CONFIG_NET_PINGADDRCONF=0
|
||||
CONFIG_NET_STATISTICS=y
|
||||
#CONFIG_NET_RECEIVE_WINDOW=
|
||||
#CONFIG_NET_ARPTAB_SIZE=8
|
||||
CONFIG_NET_BROADCAST=n
|
||||
#CONFIG_NET_FWCACHE_SIZE=2
|
||||
|
||||
#
|
||||
# UIP Network Utilities
|
||||
# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
|
||||
# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
|
||||
#
|
||||
CONFIG_NET_DHCP_LIGHT=n
|
||||
CONFIG_NET_RESOLV_ENTRIES=4
|
||||
|
||||
#
|
||||
# USB Device Configuration
|
||||
#
|
||||
# CONFIG_USBDEV
|
||||
# Enables USB device support
|
||||
# CONFIG_USBDEV_ISOCHRONOUS
|
||||
# Build in extra support for isochronous endpoints
|
||||
# CONFIG_USBDEV_DUALSPEED
|
||||
# Hardware handles high and full speed operation (USB 2.0)
|
||||
# CONFIG_USBDEV_SELFPOWERED
|
||||
# Will cause USB features to indicate that the device is
|
||||
# self-powered
|
||||
# CONFIG_USBDEV_MAXPOWER
|
||||
# Maximum power consumption in mA
|
||||
# CONFIG_USBDEV_TRACE
|
||||
# Enables USB tracing for debug
|
||||
# CONFIG_USBDEV_TRACE_NRECORDS
|
||||
# Number of trace entries to remember
|
||||
#
|
||||
CONFIG_USBDEV=n
|
||||
CONFIG_USBDEV_ISOCHRONOUS=n
|
||||
CONFIG_USBDEV_DUALSPEED=n
|
||||
CONFIG_USBDEV_SELFPOWERED=y
|
||||
CONFIG_USBDEV_REMOTEWAKEUP=n
|
||||
CONFIG_USBDEV_MAXPOWER=100
|
||||
CONFIG_USBDEV_TRACE=n
|
||||
CONFIG_USBDEV_TRACE_NRECORDS=128
|
||||
|
||||
#
|
||||
# USB Serial Device Configuration
|
||||
#
|
||||
# CONFIG_USBSER
|
||||
# Enable compilation of the USB serial driver
|
||||
# CONFIG_USBSER_EPINTIN
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# interrupt IN operation
|
||||
# CONFIG_USBSER_EPBULKOUT
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# bulk OUT operation
|
||||
# CONFIG_USBSER_EPBULKIN
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# bulk IN operation
|
||||
# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
|
||||
# The number of write/read requests that can be in flight
|
||||
# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
|
||||
# The vendor ID code/string
|
||||
# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
|
||||
# The product ID code/string
|
||||
# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
|
||||
# Size of the serial receive/transmit buffers
|
||||
#
|
||||
CONFIG_USBSER=n
|
||||
CONFIG_USBSER_EPINTIN=1
|
||||
CONFIG_USBSER_EPBULKOUT=2
|
||||
CONFIG_USBSER_EPBULKIN=3
|
||||
CONFIG_USBSER_NWRREQS=4
|
||||
CONFIG_USBSER_NRDREQS=4
|
||||
CONFIG_USBSER_VENDORID=0x067b
|
||||
CONFIG_USBSER_PRODUCTID=0x2303
|
||||
CONFIG_USBSER_VENDORSTR="Nuttx"
|
||||
CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
|
||||
CONFIG_USBSER_RXBUFSIZE=512
|
||||
CONFIG_USBSER_TXBUFSIZE=512
|
||||
|
||||
#
|
||||
# USB Storage Device Configuration
|
||||
#
|
||||
# CONFIG_USBSTRG
|
||||
# Enable compilation of the USB storage driver
|
||||
# CONFIG_USBSTRG_EP0MAXPACKET
|
||||
# Max packet size for endpoint 0
|
||||
# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
|
||||
# The logical 7-bit address of a hardware endpoints that support
|
||||
# bulk OUT and IN operations
|
||||
# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
|
||||
# The number of write/read requests that can be in flight
|
||||
# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
|
||||
# The size of the buffer in each write/read request. This
|
||||
# value needs to be at least as large as the endpoint
|
||||
# maxpacket and ideally as large as a block device sector.
|
||||
# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
|
||||
# The vendor ID code/string
|
||||
# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
|
||||
# The product ID code/string
|
||||
# CONFIG_USBSTRG_REMOVABLE
|
||||
# Select if the media is removable
|
||||
#
|
||||
CONFIG_USBSTRG=n
|
||||
CONFIG_USBSTRG_EP0MAXPACKET=64
|
||||
CONFIG_USBSTRG_EPBULKOUT=2
|
||||
CONFIG_USBSTRG_EPBULKIN=5
|
||||
CONFIG_USBSTRG_NRDREQS=2
|
||||
CONFIG_USBSTRG_NWRREQS=2
|
||||
CONFIG_USBSTRG_BULKINREQLEN=256
|
||||
CONFIG_USBSTRG_BULKOUTREQLEN=256
|
||||
CONFIG_USBSTRG_VENDORID=0x584e
|
||||
CONFIG_USBSTRG_VENDORSTR="NuttX"
|
||||
CONFIG_USBSTRG_PRODUCTID=0x5342
|
||||
CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
|
||||
CONFIG_USBSTRG_VERSIONNO=0x0399
|
||||
CONFIG_USBSTRG_REMOVABLE=y
|
||||
|
||||
#
|
||||
# Settings for examples/uip
|
||||
#
|
||||
CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_UIP_DHCPC=n
|
||||
|
||||
#
|
||||
# Settings for examples/nettest
|
||||
CONFIG_EXAMPLE_NETTEST_SERVER=n
|
||||
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
|
||||
CONFIG_EXAMPLE_NETTEST_NOMAC=n
|
||||
CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
|
||||
|
||||
#
|
||||
# Settings for examples/buttons
|
||||
#
|
||||
# CONFIG_EXAMPLE_BUTTONS_MIN and CONFIG_EXAMPLE_BUTTONS_MAX
|
||||
# Lowest and highest button number (0-7)
|
||||
# CONFIG_EXAMPLE_IRQBUTTONS_MIN and CONFIG_EXAMPLE_IRQBUTTONS_MAX
|
||||
# Lowest and highest interrupting button number (-7)
|
||||
# CONFIG_EXAMPLE_BUTTONS_NAMEn - Name for button n
|
||||
#
|
||||
CONFIG_EXAMPLE_BUTTONS_MIN=0
|
||||
CONFIG_EXAMPLE_BUTTONS_MAX=7
|
||||
CONFIG_EXAMPLE_IRQBUTTONS_MIN=2
|
||||
CONFIG_EXAMPLE_IRQBUTTONS_MAX=7
|
||||
CONFIG_EXAMPLE_BUTTONS_NAME0="WAKEUP"
|
||||
CONFIG_EXAMPLE_BUTTONS_NAME1="TAMPER"
|
||||
CONFIG_EXAMPLE_BUTTONS_NAME2="KEY"
|
||||
CONFIG_EXAMPLE_BUTTONS_NAME3="SELECT"
|
||||
CONFIG_EXAMPLE_BUTTONS_NAME4="DOWN"
|
||||
CONFIG_EXAMPLE_BUTTONS_NAME5="LEFT"
|
||||
CONFIG_EXAMPLE_BUTTONS_NAME6="RIGHT"
|
||||
CONFIG_EXAMPLE_BUTTONS_NAME7="UP"
|
||||
|
||||
#
|
||||
# Settings for examples/ostest
|
||||
#
|
||||
CONFIG_EXAMPLES_OSTEST_LOOPS=1
|
||||
CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
|
||||
CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
|
||||
|
||||
#
|
||||
# Settings for apps/nshlib
|
||||
#
|
||||
# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
|
||||
# CONFIG_NSH_STRERROR - Use strerror(errno)
|
||||
# CONFIG_NSH_LINELEN - Maximum length of one command line
|
||||
# CONFIG_NSH_STACKSIZE - Stack size to use for new threads.
|
||||
# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
|
||||
# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
|
||||
# CONFIG_NSH_DISABLEBG - Disable background commands
|
||||
# CONFIG_NSH_ROMFSETC - Use startup script in /etc
|
||||
# CONFIG_NSH_CONSOLE - Use serial console front end
|
||||
# CONFIG_NSH_TELNET - Use telnetd console front end
|
||||
# CONFIG_NSH_ARCHINIT - Platform provides architecture
|
||||
# specific initialization (nsh_archinitialize()).
|
||||
#
|
||||
# If CONFIG_NSH_TELNET is selected:
|
||||
# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
|
||||
# CONFIG_NSH_DHCPC - Obtain address using DHCP
|
||||
# CONFIG_NSH_IPADDR - Provides static IP address
|
||||
# CONFIG_NSH_DRIPADDR - Provides static router IP address
|
||||
# CONFIG_NSH_NETMASK - Provides static network mask
|
||||
# CONFIG_NSH_NOMAC - Use a bogus MAC address
|
||||
#
|
||||
# If CONFIG_NSH_ROMFSETC is selected:
|
||||
# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
|
||||
# CONFIG_NSH_INITSCRIPT - Relative path to init script
|
||||
# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
|
||||
# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
|
||||
# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
|
||||
# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
|
||||
# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
|
||||
# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
|
||||
#
|
||||
CONFIG_NSH_FILEIOSIZE=512
|
||||
CONFIG_NSH_STRERROR=n
|
||||
CONFIG_NSH_LINELEN=64
|
||||
CONFIG_NSH_STACKSIZE=2048
|
||||
CONFIG_NSH_NESTDEPTH=3
|
||||
CONFIG_NSH_DISABLESCRIPT=n
|
||||
CONFIG_NSH_DISABLEBG=n
|
||||
CONFIG_NSH_ROMFSETC=n
|
||||
CONFIG_NSH_CONSOLE=y
|
||||
CONFIG_NSH_TELNET=n
|
||||
CONFIG_NSH_ARCHINIT=n
|
||||
CONFIG_NSH_IOBUFFER_SIZE=512
|
||||
CONFIG_NSH_DHCPC=n
|
||||
CONFIG_NSH_NOMAC=n
|
||||
CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_NSH_ROMFSMOUNTPT="/etc"
|
||||
CONFIG_NSH_INITSCRIPT="init.d/rcS"
|
||||
CONFIG_NSH_ROMFSDEVNO=0
|
||||
CONFIG_NSH_ROMFSSECTSIZE=64
|
||||
CONFIG_NSH_FATDEVNO=1
|
||||
CONFIG_NSH_FATSECTSIZE=512
|
||||
CONFIG_NSH_FATNSECTORS=1024
|
||||
CONFIG_NSH_FATMOUNTPT=/tmp
|
||||
|
||||
#
|
||||
# Architecture-specific NSH options
|
||||
#
|
||||
CONFIG_NSH_MMCSDSPIPORTNO=0
|
||||
CONFIG_NSH_MMCSDSLOTNO=0
|
||||
CONFIG_NSH_MMCSDMINOR=0
|
||||
|
||||
#
|
||||
# Settings for examples/usbserial
|
||||
#
|
||||
# CONFIG_EXAMPLES_USBSERIAL_INONLY
|
||||
# Only verify IN (device-to-host) data transfers. Default: both
|
||||
# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
|
||||
# Only verify OUT (host-to-device) data transfers. Default: both
|
||||
# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
|
||||
# Send only small, single packet messages. Default: Send large and small.
|
||||
# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
|
||||
# Send only large, multi-packet messages. Default: Send large and small.
|
||||
#
|
||||
CONFIG_EXAMPLES_USBSERIAL_INONLY=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
|
||||
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
|
||||
|
||||
#
|
||||
# Stack and heap information
|
||||
#
|
||||
# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
|
||||
# operation from FLASH but must copy initialized .data sections to RAM.
|
||||
# (should also be =n for the Hy-Mini STM32v which always runs from flash)
|
||||
# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH
|
||||
# but copy themselves entirely into RAM for better performance.
|
||||
# CONFIG_CUSTOM_STACK - The up_ implementation will handle
|
||||
# all stack operations outside of the nuttx model.
|
||||
# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
|
||||
# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
|
||||
# This is the thread that (1) performs the inital boot of the system up
|
||||
# to the point where user_start() is spawned, and (2) there after is the
|
||||
# IDLE thread that executes only when there is no other thread ready to
|
||||
# run.
|
||||
# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
|
||||
# for the main user thread that begins at the user_start() entry point.
|
||||
# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
|
||||
# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
|
||||
# CONFIG_HEAP_BASE - The beginning of the heap
|
||||
# CONFIG_HEAP_SIZE - The size of the heap
|
||||
#
|
||||
CONFIG_BOOT_RUNFROMFLASH=n
|
||||
CONFIG_BOOT_COPYTORAM=n
|
||||
CONFIG_CUSTOM_STACK=n
|
||||
CONFIG_STACK_POINTER=
|
||||
CONFIG_IDLETHREAD_STACKSIZE=1024
|
||||
CONFIG_USERMAIN_STACKSIZE=2048
|
||||
CONFIG_PTHREAD_STACK_MIN=256
|
||||
CONFIG_PTHREAD_STACK_DEFAULT=2048
|
||||
CONFIG_HEAP_BASE=
|
||||
CONFIG_HEAP_SIZE=
|
|
@ -0,0 +1,112 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/buttons/ld.script
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F103VCT6 has 256Kb of FLASH beginning at address 0x0800:0000 and
|
||||
* 48Kb of SRAM beginning at address 0x2000:0000. When booting from FLASH,
|
||||
* FLASH memory is aliased to address 0x0000:0000 where the code expects to
|
||||
* begin execution by jumping to the entry point in the 0x0800:0000 address
|
||||
* range.
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x08000000, LENGTH = 256K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 48K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
/* The STM32F103V has 48Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} >sram
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
|
@ -0,0 +1,111 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/buttons/ld.script.dfu
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
|
||||
* 64Kb of SRAM beginning at address 0x2000:0000. Here we assume that the
|
||||
* Hy-Mini STM32v's DFU bootloader is being used. In that case, the corrct
|
||||
* load .text load address is 0x08003000 (leaving 464Kb).
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x08003000, LENGTH = 464K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} >sram
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
|
@ -0,0 +1,47 @@
|
|||
#!/bin/bash
|
||||
# configs/hymini-stm32v/buttons/setenv.sh
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
|
||||
if [ "$(basename $0)" = "setenv.sh" ] ; then
|
||||
echo "You must source this script, not run it!" 1>&2
|
||||
exit 1
|
||||
fi
|
||||
|
||||
if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi
|
||||
|
||||
WD=`pwd`
|
||||
export RIDE_BIN="/cygdrive/c/Program Files/Raisonance/Ride/arm-gcc/bin"
|
||||
export BUILDROOT_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
|
||||
export PATH="${BUILDROOT_BIN}:${RIDE_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
|
||||
|
||||
echo "PATH : ${PATH}"
|
|
@ -0,0 +1 @@
|
|||
This directory contains header files unique to the HY-MiniSTM32V development board.
|
|
@ -0,0 +1,230 @@
|
|||
/************************************************************************************
|
||||
* configs/hymini-stm32v/include/board.h
|
||||
* include/arch/board/board.h
|
||||
*
|
||||
* Copyright (C) 2011 Laurent Latil. All rights reserved.
|
||||
* Author: Laurent Latil <laurent@latil.nom.fr>
|
||||
*
|
||||
* Derives, in part, from configs/stm3210e-eval/include/board.h
|
||||
*
|
||||
* Copyright (C) 2009 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
#ifndef __ARCH_BOARD_BOARD_H
|
||||
#define __ARCH_BOARD_BOARD_H
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
#ifndef __ASSEMBLY__
|
||||
# include <stdint.h>
|
||||
#endif
|
||||
#include "stm32_rcc.h"
|
||||
#include "stm32_sdio.h"
|
||||
#include "stm32_internal.h"
|
||||
|
||||
/************************************************************************************
|
||||
* Definitions
|
||||
************************************************************************************/
|
||||
|
||||
/* Clocking *************************************************************************/
|
||||
|
||||
/* On-board crystal frequency is 8MHz (HSE) */
|
||||
|
||||
#define STM32_BOARD_XTAL 8000000ul
|
||||
|
||||
/* PLL source is HSE/1, PLL multipler is 9: PLL frequency is 8MHz (XTAL) x 9 = 72MHz */
|
||||
|
||||
#define STM32_CFGR_PLLSRC RCC_CFGR_PLLSRC
|
||||
#define STM32_CFGR_PLLXTPRE 0
|
||||
#define STM32_CFGR_PLLMUL RCC_CFGR_PLLMUL_CLKx9
|
||||
#define STM32_PLL_FREQUENCY (9*STM32_BOARD_XTAL)
|
||||
|
||||
/* Use the PLL and set the SYSCLK source to be the PLL */
|
||||
|
||||
#define STM32_SYSCLK_SW RCC_CFGR_SW_PLL
|
||||
#define STM32_SYSCLK_SWS RCC_CFGR_SWS_PLL
|
||||
#define STM32_SYSCLK_FREQUENCY STM32_PLL_FREQUENCY
|
||||
|
||||
/* AHB clock (HCLK) is SYSCLK (72MHz) */
|
||||
|
||||
#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK
|
||||
#define STM32_HCLK_FREQUENCY STM32_PLL_FREQUENCY
|
||||
#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* same as above, to satisfy compiler */
|
||||
|
||||
/* APB2 clock (PCLK2) is HCLK (72MHz) */
|
||||
|
||||
#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK
|
||||
#define STM32_PCLK2_FREQUENCY STM32_HCLK_FREQUENCY
|
||||
|
||||
/* APB1 clock (PCLK1) is HCLK/2 (36MHz) */
|
||||
|
||||
#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd2
|
||||
#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/2)
|
||||
|
||||
/* USB divider -- Divide PLL clock by 1.5 */
|
||||
|
||||
#define STM32_CFGR_USBPRE 0
|
||||
|
||||
/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx
|
||||
* otherwise frequency is 2xAPBx.
|
||||
* Note: TIM1,8 are on APB2, others on APB1 */
|
||||
|
||||
#define STM32_TIM18_FREQUENCY STM32_HCLK_FREQUENCY
|
||||
#define STM32_TIM27_FREQUENCY STM32_HCLK_FREQUENCY
|
||||
|
||||
/* SDIO dividers. Note that slower clocking is required when DMA is disabled
|
||||
* in order to avoid RX overrun/TX underrun errors due to delayed responses
|
||||
* to service FIFOs in interrupt driven mode. These values have not been
|
||||
* tuned!!!
|
||||
*
|
||||
* HCLK=72MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(178+2)=400 KHz
|
||||
*/
|
||||
|
||||
#define SDIO_INIT_CLKDIV (178 << SDIO_CLKCR_CLKDIV_SHIFT)
|
||||
|
||||
/* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(2+2)=18 MHz
|
||||
* DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz
|
||||
*/
|
||||
|
||||
#ifdef CONFIG_SDIO_DMA
|
||||
# define SDIO_MMCXFR_CLKDIV (2 << SDIO_CLKCR_CLKDIV_SHIFT)
|
||||
#else
|
||||
# define SDIO_MMCXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT)
|
||||
#endif
|
||||
|
||||
/* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(1+2)=24 MHz
|
||||
* DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz
|
||||
*/
|
||||
|
||||
#ifdef CONFIG_SDIO_DMA
|
||||
# define SDIO_SDXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT)
|
||||
#else
|
||||
# define SDIO_SDXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT)
|
||||
#endif
|
||||
|
||||
/* LED definitions ******************************************************************/
|
||||
|
||||
/* The board has 2 LEDs that we will encode as: */
|
||||
#define LED_STARTED 0 /* No LEDs */
|
||||
#define LED_HEAPALLOCATE 1 /* LED1 on */
|
||||
#define LED_IRQSENABLED 2 /* LED2 on */
|
||||
#define LED_STACKCREATED 3 /* LED1 on */
|
||||
#define LED_INIRQ 4 /* LED1 off */
|
||||
#define LED_SIGNAL 5 /* LED2 on */
|
||||
#define LED_ASSERTION 6 /* LED1 + LED2 */
|
||||
#define LED_PANIC 7 /* LED1 / LED2 blinking */
|
||||
|
||||
/* The board supports two user buttons
|
||||
*
|
||||
* KeyA -- Connected to PC.13
|
||||
* KeyB -- Connected to PB.2
|
||||
*/
|
||||
|
||||
#define BUTTON_KEYA 0
|
||||
#define BUTTON_KEYB 1
|
||||
|
||||
#define NUM_BUTTONS 2
|
||||
|
||||
#define BUTTON_KEYA_BIT (1 << BUTTON_KEYA)
|
||||
#define BUTTON_KEYB_BIT (1 << BUTTON_KEYB)
|
||||
|
||||
|
||||
/************************************************************************************
|
||||
* Public Data
|
||||
************************************************************************************/
|
||||
|
||||
#ifndef __ASSEMBLY__
|
||||
|
||||
#undef EXTERN
|
||||
#if defined(__cplusplus)
|
||||
#define EXTERN extern "C"
|
||||
extern "C" {
|
||||
#else
|
||||
#define EXTERN extern
|
||||
#endif
|
||||
|
||||
/************************************************************************************
|
||||
* Public Function Prototypes
|
||||
************************************************************************************/
|
||||
/************************************************************************************
|
||||
* Name: stm32_boardinitialize
|
||||
*
|
||||
* Description:
|
||||
* All STM32 architectures must provide the following entry point. This entry point
|
||||
* is called early in the initialization -- after all memory has been configured
|
||||
* and mapped but before any devices have been initialized.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
EXTERN void stm32_boardinitialize(void);
|
||||
|
||||
/************************************************************************************
|
||||
* Button support.
|
||||
*
|
||||
* Description:
|
||||
* up_buttoninit() must be called to initialize button resources. After
|
||||
* that, up_buttons() may be called to collect the current state of all
|
||||
* buttons or up_irqbutton() may be called to register button interrupt
|
||||
* handlers.
|
||||
*
|
||||
* After up_buttoninit() has been called, up_buttons() may be called to
|
||||
* collect the state of all buttons. up_buttons() returns an 8-bit bit set
|
||||
* with each bit associated with a button. See the BUTTON_*_BIT and JOYSTICK_*_BIT
|
||||
* definitions in board.h for the meaning of each bit.
|
||||
*
|
||||
* up_irqbutton() may be called to register an interrupt handler that will
|
||||
* be called when a button is depressed or released. The ID value is a
|
||||
* button enumeration value that uniquely identifies a button resource. See the
|
||||
* BUTTON_* and JOYSTICK_* definitions in board.h for the meaning of enumeration
|
||||
* value. The previous interrupt handler address is returned (so that it may
|
||||
* restored, if so desired).
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
#ifdef CONFIG_ARCH_BUTTONS
|
||||
EXTERN void up_buttoninit(void);
|
||||
EXTERN uint8_t up_buttons(void);
|
||||
#ifdef CONFIG_ARCH_IRQBUTTONS
|
||||
EXTERN xcpt_t up_irqbutton(int id, xcpt_t irqhandler);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#undef EXTERN
|
||||
#if defined(__cplusplus)
|
||||
}
|
||||
#endif
|
||||
|
||||
#endif /* __ASSEMBLY__ */
|
||||
#endif /* __ARCH_BOARD_BOARD_H */
|
|
@ -0,0 +1,174 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/nsh/Make.defs
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include ${TOPDIR}/.config
|
||||
|
||||
# Setup for the selected toolchain
|
||||
|
||||
ifeq ($(CONFIG_STM32_DFU),y)
|
||||
LDSCRIPT = ld.script.dfu
|
||||
else
|
||||
LDSCRIPT = ld.script
|
||||
endif
|
||||
|
||||
ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
|
||||
# CodeSourcery under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
|
||||
# CodeSourcery under Linux
|
||||
CROSSDEV = arm-none-eabi-
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -O2
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_DEVKITARM),y)
|
||||
# devkitARM under Windows
|
||||
CROSSDEV = arm-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_RAISONANCE),y)
|
||||
# Raisonance RIDE7 under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_BUILDROOT),y)
|
||||
# NuttX buildroot under Linux or Cygwin
|
||||
CROSSDEV = arm-elf-
|
||||
ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -Os
|
||||
endif
|
||||
|
||||
ifeq ($(WINTOOL),y)
|
||||
# Windows-native toolchains
|
||||
DIRLINK = $(TOPDIR)/tools/winlink.sh
|
||||
DIRUNLINK = $(TOPDIR)/tools/unlink.sh
|
||||
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
|
||||
ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh/$(LDSCRIPT)}"
|
||||
MAXOPTIMIZATION = -O2
|
||||
else
|
||||
# Linux/Cygwin-native toolchain
|
||||
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
||||
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
||||
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh/$(LDSCRIPT)
|
||||
endif
|
||||
|
||||
CC = $(CROSSDEV)gcc
|
||||
CXX = $(CROSSDEV)g++
|
||||
CPP = $(CROSSDEV)gcc -E
|
||||
LD = $(CROSSDEV)ld
|
||||
AR = $(CROSSDEV)ar rcs
|
||||
NM = $(CROSSDEV)nm
|
||||
OBJCOPY = $(CROSSDEV)objcopy
|
||||
OBJDUMP = $(CROSSDEV)objdump
|
||||
|
||||
ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
|
||||
ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
|
||||
|
||||
ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
|
||||
ARCHOPTIMIZATION = -g
|
||||
else
|
||||
ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
|
||||
endif
|
||||
|
||||
ARCHCFLAGS = -fno-builtin
|
||||
ARCHCXXFLAGS = -fno-builtin -fno-exceptions
|
||||
ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
|
||||
ARCHWARNINGSXX = -Wall -Wshadow
|
||||
ARCHDEFINES =
|
||||
ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
|
||||
|
||||
CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
|
||||
CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
|
||||
CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
|
||||
AFLAGS = $(CFLAGS) -D__ASSEMBLY__
|
||||
|
||||
NXFLATLDFLAGS1 = -r -d -warn-common
|
||||
NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
|
||||
LDNXFLATFLAGS = -e main -s 2048
|
||||
|
||||
OBJEXT = .o
|
||||
LIBEXT = .a
|
||||
EXEEXT =
|
||||
|
||||
ifneq ($(CROSSDEV),arm-elf-)
|
||||
LDFLAGS += -nostartfiles -nodefaultlibs
|
||||
endif
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
LDFLAGS += -g
|
||||
endif
|
||||
|
||||
define PREPROCESS
|
||||
@echo "CPP: $1->$2"
|
||||
@$(CPP) $(CPPFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILE
|
||||
@echo "CC: $1"
|
||||
@$(CC) -c $(CFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILEXX
|
||||
@echo "CXX: $1"
|
||||
@$(CXX) -c $(CXXFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ASSEMBLE
|
||||
@echo "AS: $1"
|
||||
@$(CC) -c $(AFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ARCHIVE
|
||||
echo "AR: $2"; \
|
||||
$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
|
||||
endef
|
||||
|
||||
define CLEAN
|
||||
@rm -f *.o *.a
|
||||
endef
|
||||
|
||||
HOSTCC = gcc
|
||||
HOSTINCLUDES = -I.
|
||||
HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
|
||||
HOSTLDFLAGS =
|
||||
|
|
@ -0,0 +1,41 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/nsh/appconfig
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
# Path to example in apps/examples containing the user_start entry point
|
||||
|
||||
CONFIGURED_APPS += examples/nsh
|
||||
|
||||
CONFIGURED_APPS += nshlib
|
||||
|
|
@ -0,0 +1,865 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/nsh/defconfig
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
#
|
||||
# architecture selection
|
||||
#
|
||||
# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
|
||||
# processor architecture.
|
||||
# CONFIG_ARCH_family - for use in C code. This identifies the
|
||||
# particular chip family that the architecture is implemented
|
||||
# in.
|
||||
# CONFIG_ARCH_architecture - for use in C code. This identifies the
|
||||
# specific architecture within the chip familyl.
|
||||
# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||||
# CONFIG_ARCH_CHIP_name - For use in C code
|
||||
# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
|
||||
# the board that supports the particular chip or SoC.
|
||||
# CONFIG_ARCH_BOARD_name - for use in C code
|
||||
# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
|
||||
# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
|
||||
# CONFIG_DRAM_SIZE - Describes the installed DRAM.
|
||||
# CONFIG_DRAM_START - The start address of DRAM (physical)
|
||||
# CONFIG_DRAM_END - Last address+1 of installed RAM
|
||||
# CONFIG_ARCH_IRQPRIO - The ST32F103Z supports interrupt prioritization
|
||||
# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
||||
# stack. If defined, this symbol is the size of the interrupt
|
||||
# stack in bytes. If not defined, the user task stacks will be
|
||||
# used during interrupt handling.
|
||||
# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||||
# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
|
||||
# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
||||
# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture.
|
||||
# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
||||
# cause a 100 second delay during boot-up. This 100 second delay
|
||||
# serves no purpose other than it allows you to calibrate
|
||||
# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure
|
||||
# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
|
||||
# the delay actually is 100 seconds.
|
||||
# CONFIG_ARCH_DMA - Support DMA initialization
|
||||
#
|
||||
CONFIG_ARCH=arm
|
||||
CONFIG_ARCH_ARM=y
|
||||
CONFIG_ARCH_CORTEXM3=y
|
||||
CONFIG_ARCH_CHIP=stm32
|
||||
CONFIG_ARCH_CHIP_STM32F103VCT6=y
|
||||
CONFIG_ARCH_BOARD=hymini-stm32v
|
||||
CONFIG_ARCH_BOARD_HYMINI_STM32V=y
|
||||
CONFIG_BOARD_LOOPSPERMSEC=5483
|
||||
CONFIG_DRAM_SIZE=0x0000C000
|
||||
CONFIG_DRAM_START=0x20000000
|
||||
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
||||
CONFIG_ARCH_IRQPRIO=y
|
||||
CONFIG_ARCH_INTERRUPTSTACK=n
|
||||
CONFIG_ARCH_STACKDUMP=y
|
||||
CONFIG_ARCH_BOOTLOADER=n
|
||||
CONFIG_ARCH_LEDS=y
|
||||
CONFIG_ARCH_BUTTONS=n
|
||||
CONFIG_ARCH_CALIBRATION=n
|
||||
CONFIG_ARCH_DMA=y
|
||||
|
||||
#
|
||||
# Identify toolchain and linker options
|
||||
#
|
||||
CONFIG_STM32_CODESOURCERYW=n
|
||||
CONFIG_STM32_CODESOURCERYL=y
|
||||
CONFIG_STM32_DEVKITARM=n
|
||||
CONFIG_STM32_RAISONANCE=n
|
||||
CONFIG_STM32_BUILDROOT=n
|
||||
CONFIG_STM32_DFU=n
|
||||
|
||||
#
|
||||
# Individual subsystems can be enabled:
|
||||
# AHB:
|
||||
CONFIG_STM32_DMA1=n
|
||||
CONFIG_STM32_DMA2=y
|
||||
CONFIG_STM32_CRC=n
|
||||
CONFIG_STM32_FSMC=n
|
||||
CONFIG_STM32_SDIO=y
|
||||
# APB1:
|
||||
CONFIG_STM32_TIM2=n
|
||||
CONFIG_STM32_TIM3=n
|
||||
CONFIG_STM32_TIM4=n
|
||||
CONFIG_STM32_TIM5=n
|
||||
CONFIG_STM32_TIM6=n
|
||||
CONFIG_STM32_TIM7=n
|
||||
CONFIG_STM32_WWDG=n
|
||||
CONFIG_STM32_SPI2=n
|
||||
CONFIG_STM32_SPI4=n
|
||||
CONFIG_STM32_USART2=y
|
||||
CONFIG_STM32_USART3=n
|
||||
CONFIG_STM32_UART4=n
|
||||
CONFIG_STM32_UART5=n
|
||||
CONFIG_STM32_I2C1=n
|
||||
CONFIG_STM32_I2C2=n
|
||||
CONFIG_STM32_USB=y
|
||||
CONFIG_STM32_CAN=n
|
||||
CONFIG_STM32_BKP=n
|
||||
CONFIG_STM32_PWR=n
|
||||
CONFIG_STM32_DAC=n
|
||||
# APB2:
|
||||
CONFIG_STM32_ADC1=n
|
||||
CONFIG_STM32_ADC2=n
|
||||
CONFIG_STM32_TIM1=n
|
||||
CONFIG_STM32_SPI1=n
|
||||
CONFIG_STM32_TIM8=n
|
||||
CONFIG_STM32_USART1=y
|
||||
CONFIG_STM32_ADC3=n
|
||||
|
||||
#
|
||||
# Timer and I2C devices may need to the following to force power to be applied:
|
||||
#
|
||||
#CONFIG_STM32_FORCEPOWER=y
|
||||
|
||||
#
|
||||
# STM32F103V specific serial device driver settings
|
||||
#
|
||||
# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
|
||||
# console and ttys0 (default is the USART1).
|
||||
# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
|
||||
# This specific the size of the receive buffer
|
||||
# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
|
||||
# being sent. This specific the size of the transmit buffer
|
||||
# CONFIG_USARTn_BAUD - The configure BAUD of the UART. Must be
|
||||
# CONFIG_USARTn_BITS - The number of bits. Must be either 7 or 8.
|
||||
# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
||||
# CONFIG_USARTn_2STOP - Two stop bits
|
||||
#
|
||||
CONFIG_USART1_SERIAL_CONSOLE=y
|
||||
CONFIG_USART2_SERIAL_CONSOLE=n
|
||||
CONFIG_USART3_SERIAL_CONSOLE=n
|
||||
CONFIG_USART4_SERIAL_CONSOLE=n
|
||||
CONFIG_USART5_SERIAL_CONSOLE=n
|
||||
|
||||
CONFIG_USART1_TXBUFSIZE=256
|
||||
CONFIG_USART2_TXBUFSIZE=256
|
||||
CONFIG_USART3_TXBUFSIZE=256
|
||||
CONFIG_USART4_TXBUFSIZE=256
|
||||
CONFIG_USART5_TXBUFSIZE=256
|
||||
|
||||
CONFIG_USART1_RXBUFSIZE=256
|
||||
CONFIG_USART2_RXBUFSIZE=256
|
||||
CONFIG_USART3_RXBUFSIZE=256
|
||||
CONFIG_USART4_RXBUFSIZE=256
|
||||
CONFIG_USART5_RXBUFSIZE=256
|
||||
|
||||
CONFIG_USART1_BAUD=115200
|
||||
CONFIG_USART2_BAUD=115200
|
||||
CONFIG_USART3_BAUD=115200
|
||||
CONFIG_USART4_BAUD=115200
|
||||
CONFIG_USART5_BAUD=115200
|
||||
|
||||
CONFIG_USART1_BITS=8
|
||||
CONFIG_USART2_BITS=8
|
||||
CONFIG_USART3_BITS=8
|
||||
CONFIG_USART4_BITS=8
|
||||
CONFIG_USART5_BITS=8
|
||||
|
||||
CONFIG_USART1_PARITY=0
|
||||
CONFIG_USART2_PARITY=0
|
||||
CONFIG_USART3_PARITY=0
|
||||
CONFIG_USART4_PARITY=0
|
||||
CONFIG_USART5_PARITY=0
|
||||
|
||||
CONFIG_USART1_2STOP=0
|
||||
CONFIG_USART2_2STOP=0
|
||||
CONFIG_USART3_2STOP=0
|
||||
CONFIG_USART4_2STOP=0
|
||||
CONFIG_USART5_2STOP=0
|
||||
|
||||
#
|
||||
# STM32F103V specific SSI device driver settings
|
||||
#
|
||||
# CONFIG_SSIn_DISABLE - select to disable all support for
|
||||
# the SSI
|
||||
# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
|
||||
# Poll-waiting is recommended if the interrupt rate would be to
|
||||
# high in the interrupt driven case.
|
||||
# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
|
||||
# emptying the Rx FIFO. If the SPI frequency is high and this
|
||||
# value is large, then larger values of this setting may cause
|
||||
# Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
|
||||
#
|
||||
CONFIG_SSI0_DISABLE=n
|
||||
CONFIG_SSI1_DISABLE=y
|
||||
CONFIG_SSI_POLLWAIT=y
|
||||
#CONFIG_SSI_TXLIMIT=4
|
||||
|
||||
#
|
||||
# General build options
|
||||
#
|
||||
# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
|
||||
# BSPs from www.ridgerun.com using the tools/mkimage.sh script
|
||||
# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_RAW_BINARY - make a raw binary format file used with many
|
||||
# different loaders using the GNU objcopy program. This option
|
||||
# should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_HAVE_LIBM - toolchain supports libm.a
|
||||
#
|
||||
CONFIG_RRLOAD_BINARY=n
|
||||
CONFIG_INTELHEX_BINARY=n
|
||||
CONFIG_MOTOROLA_SREC=n
|
||||
CONFIG_RAW_BINARY=y
|
||||
CONFIG_HAVE_LIBM=n
|
||||
|
||||
#
|
||||
# General OS setup
|
||||
#
|
||||
# CONFIG_APPS_DIR - Identifies the relative path to the directory
|
||||
# that builds the application to link with NuttX. Default: ../apps
|
||||
# CONFIG_DEBUG - enables built-in debug options
|
||||
# CONFIG_DEBUG_VERBOSE - enables verbose debug output
|
||||
# CONFIG_DEBUG_SYMBOLS - build without optimization and with
|
||||
# debug symbols (needed for use with a debugger).
|
||||
# CONFIG_MM_REGIONS - If the architecture includes multiple
|
||||
# regions of memory to allocate from, this specifies the
|
||||
# number of memory regions that the memory manager must
|
||||
# handle and enables the API mm_addregion(start, end);
|
||||
# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
|
||||
# time console output
|
||||
# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
|
||||
# or MSEC_PER_TICK=10. This setting may be defined to
|
||||
# inform NuttX that the processor hardware is providing
|
||||
# system timer interrupts at some interrupt interval other
|
||||
# than 10 msec.
|
||||
# CONFIG_RR_INTERVAL - The round robin timeslice will be set
|
||||
# this number of milliseconds; Round robin scheduling can
|
||||
# be disabled by setting this value to zero.
|
||||
# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in
|
||||
# scheduler to monitor system performance
|
||||
# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
|
||||
# task name to save in the TCB. Useful if scheduler
|
||||
# instrumentation is selected. Set to zero to disable.
|
||||
# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
|
||||
# Used to initialize the internal time logic.
|
||||
# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
|
||||
# You would only need this if you are concerned about accurate
|
||||
# time conversions in the past or in the distant future.
|
||||
# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
|
||||
# would only need this if you are concerned about accurate
|
||||
# time conversion in the distand past. You must also define
|
||||
# CONFIG_GREGORIAN_TIME in order to use Julian time.
|
||||
# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
|
||||
# provides /dev/console. Enables stdout, stderr, stdin.
|
||||
# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
|
||||
# driver (minimul support)
|
||||
# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
|
||||
# errorcheck mutexes. Enables pthread_mutexattr_settype().
|
||||
# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
|
||||
# inheritance on mutexes and semaphores.
|
||||
# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
|
||||
# inheritance is enabled. It defines the maximum number of
|
||||
# different threads (minus one) that can take counts on a
|
||||
# semaphore with priority inheritance support. This may be
|
||||
# set to zero if priority inheritance is disabled OR if you
|
||||
# are only using semaphores as mutexes (only one holder) OR
|
||||
# if no more than two threads participate using a counting
|
||||
# semaphore.
|
||||
# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled,
|
||||
# then this setting is the maximum number of higher priority
|
||||
# threads (minus 1) than can be waiting for another thread
|
||||
# to release a count on a semaphore. This value may be set
|
||||
# to zero if no more than one thread is expected to wait for
|
||||
# a semaphore.
|
||||
# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
|
||||
# by task_create() when a new task is started. If set, all
|
||||
# files/drivers will appear to be closed in the new task.
|
||||
# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
|
||||
# three file descriptors (stdin, stdout, stderr) by task_create()
|
||||
# when a new task is started. If set, all files/drivers will
|
||||
# appear to be closed in the new task except for stdin, stdout,
|
||||
# and stderr.
|
||||
# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
|
||||
# desciptors by task_create() when a new task is started. If
|
||||
# set, all sockets will appear to be closed in the new task.
|
||||
# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
|
||||
# This format will support execution of NuttX binaries located
|
||||
# in a ROMFS filesystem (see examples/nxflat).
|
||||
# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to
|
||||
# handle delayed processing from interrupt handlers. This feature
|
||||
# is required for some drivers but, if there are not complaints,
|
||||
# can be safely disabled. The worker thread also performs
|
||||
# garbage collection -- completing any delayed memory deallocations
|
||||
# from interrupt handlers. If the worker thread is disabled,
|
||||
# then that clean will be performed by the IDLE thread instead
|
||||
# (which runs at the lowest of priority and may not be appropriate
|
||||
# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE
|
||||
# is enabled, then the following options can also be used:
|
||||
# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
|
||||
# thread. Default: 50
|
||||
# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
|
||||
# work in units of microseconds. Default: 50*1000 (50 MS).
|
||||
# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
|
||||
# thread. Default: CONFIG_IDLETHREAD_STACKSIZE.
|
||||
# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
|
||||
# the worker thread. Default: 4
|
||||
#
|
||||
#CONFIG_APPS_DIR=
|
||||
CONFIG_DEBUG=n
|
||||
CONFIG_DEBUG_VERBOSE=n
|
||||
CONFIG_DEBUG_SYMBOLS=n
|
||||
CONFIG_MM_REGIONS=1
|
||||
CONFIG_ARCH_LOWPUTC=y
|
||||
CONFIG_RR_INTERVAL=200
|
||||
CONFIG_SCHED_INSTRUMENTATION=n
|
||||
CONFIG_TASK_NAME_SIZE=0
|
||||
CONFIG_START_YEAR=2009
|
||||
CONFIG_START_MONTH=9
|
||||
CONFIG_START_DAY=21
|
||||
CONFIG_GREGORIAN_TIME=n
|
||||
CONFIG_JULIAN_TIME=n
|
||||
CONFIG_DEV_CONSOLE=y
|
||||
CONFIG_DEV_LOWCONSOLE=n
|
||||
CONFIG_MUTEX_TYPES=n
|
||||
CONFIG_PRIORITY_INHERITANCE=n
|
||||
CONFIG_SEM_PREALLOCHOLDERS=0
|
||||
CONFIG_SEM_NNESTPRIO=0
|
||||
CONFIG_FDCLONE_DISABLE=n
|
||||
CONFIG_FDCLONE_STDIO=n
|
||||
CONFIG_SDCLONE_DISABLE=y
|
||||
CONFIG_NXFLAT=n
|
||||
CONFIG_SCHED_WORKQUEUE=y
|
||||
CONFIG_SCHED_WORKPRIORITY=50
|
||||
CONFIG_SCHED_WORKPERIOD=(50*1000)
|
||||
CONFIG_SCHED_WORKSTACKSIZE=1024
|
||||
CONFIG_SIG_SIGWORK=4
|
||||
|
||||
#
|
||||
# The following can be used to disable categories of
|
||||
# APIs supported by the OS. If the compiler supports
|
||||
# weak functions, then it should not be necessary to
|
||||
# disable functions unless you want to restrict usage
|
||||
# of those APIs.
|
||||
#
|
||||
# There are certain dependency relationships in these
|
||||
# features.
|
||||
#
|
||||
# o mq_notify logic depends on signals to awaken tasks
|
||||
# waiting for queues to become full or empty.
|
||||
# o pthread_condtimedwait() depends on signals to wake
|
||||
# up waiting tasks.
|
||||
#
|
||||
CONFIG_DISABLE_CLOCK=n
|
||||
CONFIG_DISABLE_POSIX_TIMERS=n
|
||||
CONFIG_DISABLE_PTHREAD=n
|
||||
CONFIG_DISABLE_SIGNALS=n
|
||||
CONFIG_DISABLE_MQUEUE=n
|
||||
CONFIG_DISABLE_MOUNTPOINT=n
|
||||
CONFIG_DISABLE_ENVIRON=n
|
||||
CONFIG_DISABLE_POLL=y
|
||||
|
||||
#
|
||||
# Misc libc settings
|
||||
#
|
||||
# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
|
||||
# little smaller if we do not support fieldwidthes
|
||||
#
|
||||
CONFIG_NOPRINTF_FIELDWIDTH=n
|
||||
|
||||
#
|
||||
# Allow for architecture optimized implementations
|
||||
#
|
||||
# The architecture can provide optimized versions of the
|
||||
# following to improve system performance
|
||||
#
|
||||
CONFIG_ARCH_MEMCPY=n
|
||||
CONFIG_ARCH_MEMCMP=n
|
||||
CONFIG_ARCH_MEMMOVE=n
|
||||
CONFIG_ARCH_MEMSET=n
|
||||
CONFIG_ARCH_STRCMP=n
|
||||
CONFIG_ARCH_STRCPY=n
|
||||
CONFIG_ARCH_STRNCPY=n
|
||||
CONFIG_ARCH_STRLEN=n
|
||||
CONFIG_ARCH_STRNLEN=n
|
||||
CONFIG_ARCH_BZERO=n
|
||||
|
||||
#
|
||||
# Sizes of configurable things (0 disables)
|
||||
#
|
||||
# CONFIG_MAX_TASKS - The maximum number of simultaneously
|
||||
# active tasks. This value must be a power of two.
|
||||
# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
|
||||
# of parameters that a task may receive (i.e., maxmum value
|
||||
# of 'argc')
|
||||
# CONFIG_NPTHREAD_KEYS - The number of items of thread-
|
||||
# specific data that can be retained
|
||||
# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
|
||||
# descriptors (one for each open)
|
||||
# CONFIG_NFILE_STREAMS - The maximum number of streams that
|
||||
# can be fopen'ed
|
||||
# CONFIG_NAME_MAX - The maximum size of a file name.
|
||||
# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
|
||||
# on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_NUNGET_CHARS - Number of characters that can be
|
||||
# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
|
||||
# structures. The system manages a pool of preallocated
|
||||
# message structures to minimize dynamic allocations
|
||||
# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
|
||||
# a fixed payload size given by this settin (does not include
|
||||
# other message structure overhead.
|
||||
# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
|
||||
# can be passed to a watchdog handler
|
||||
# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
|
||||
# structures. The system manages a pool of preallocated
|
||||
# watchdog structures to minimize dynamic allocations
|
||||
# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
|
||||
# timer structures. The system manages a pool of preallocated
|
||||
# timer structures to minimize dynamic allocations. Set to
|
||||
# zero for all dynamic allocations.
|
||||
#
|
||||
CONFIG_MAX_TASKS=16
|
||||
CONFIG_MAX_TASK_ARGS=4
|
||||
CONFIG_NPTHREAD_KEYS=4
|
||||
CONFIG_NFILE_DESCRIPTORS=8
|
||||
CONFIG_NFILE_STREAMS=8
|
||||
CONFIG_NAME_MAX=32
|
||||
CONFIG_STDIO_BUFFER_SIZE=256
|
||||
CONFIG_NUNGET_CHARS=2
|
||||
CONFIG_PREALLOC_MQ_MSGS=4
|
||||
CONFIG_MQ_MAXMSGSIZE=32
|
||||
CONFIG_MAX_WDOGPARMS=2
|
||||
CONFIG_PREALLOC_WDOGS=4
|
||||
CONFIG_PREALLOC_TIMERS=4
|
||||
|
||||
#
|
||||
# Filesystem configuration
|
||||
#
|
||||
# CONFIG_FS_FAT - Enable FAT filesystem support
|
||||
# CONFIG_FAT_SECTORSIZE - Max supported sector size
|
||||
# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
|
||||
# file name support.
|
||||
# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims
|
||||
# patents on FAT long file name technology. Please read the
|
||||
# disclaimer in the top-level COPYING file and only enable this
|
||||
# feature if you understand these issues.
|
||||
# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
|
||||
# default, maximum long file name is 255 bytes. This can eat up
|
||||
# a lot of memory (especially stack space). If you are willing
|
||||
# to live with some non-standard, short long file names, then
|
||||
# define this value. A good choice would be the same value as
|
||||
# selected for CONFIG_NAME_MAX which will limit the visibility
|
||||
# of longer file names anyway.
|
||||
# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
|
||||
# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH.
|
||||
# This must have one of the values of 0xff or 0x00.
|
||||
# Default: 0xff.
|
||||
# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
|
||||
# don't both with file chunks smaller than this number of data bytes.
|
||||
# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
|
||||
# Default: 255.
|
||||
# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
|
||||
# don't both with file chunks smaller than this number of data bytes.
|
||||
# Default: 32.
|
||||
# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
|
||||
# packing files together toward the end of the file or, if file are
|
||||
# deleted at the end of the file, clean up can simply mean erasing
|
||||
# the end of FLASH memory so that it can be re-used again. However,
|
||||
# doing this can also harm the life of the FLASH part because it can
|
||||
# mean that the tail end of the FLASH is re-used too often. This
|
||||
# threshold determines if/when it is worth erased the tail end of FLASH
|
||||
# and making it available for re-use (and possible over-wear).
|
||||
# Default: 8192.
|
||||
# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
|
||||
# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
|
||||
# option will enable a limited form of memory mapping that is
|
||||
# implemented by copying whole files into memory.
|
||||
#
|
||||
CONFIG_FS_FAT=y
|
||||
CONFIG_FAT_LCNAMES=y
|
||||
CONFIG_FAT_LFN=n
|
||||
CONFIG_FAT_MAXFNAME=32
|
||||
CONFIG_FS_NXFFS=n
|
||||
CONFIG_FS_ROMFS=n
|
||||
|
||||
#
|
||||
# SPI-based MMC/SD driver
|
||||
#
|
||||
# CONFIG_MMCSD_NSLOTS
|
||||
# Number of MMC/SD slots supported by the driver
|
||||
# CONFIG_MMCSD_READONLY
|
||||
# Provide read-only access (default is read/write)
|
||||
# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
|
||||
# Default is 20MHz.
|
||||
#
|
||||
CONFIG_MMCSD_NSLOTS=1
|
||||
CONFIG_MMCSD_READONLY=n
|
||||
CONFIG_MMCSD_SPICLOCK=12500000
|
||||
|
||||
#
|
||||
# Block driver buffering
|
||||
#
|
||||
# CONFIG_FS_READAHEAD
|
||||
# Enable read-ahead buffering
|
||||
# CONFIG_FS_WRITEBUFFER
|
||||
# Enable write buffering
|
||||
#
|
||||
CONFIG_FS_READAHEAD=n
|
||||
CONFIG_FS_WRITEBUFFER=n
|
||||
|
||||
#
|
||||
# STM32 SDIO-based MMC/SD driver
|
||||
#
|
||||
# CONFIG_SDIO_DMA - Support DMA data transfers. Requires CONFIG_STM32_SDIO
|
||||
# and CONFIG_STM32_DMA2.
|
||||
# CONFIG_SDIO_PRI - Select SDIO interrupt prority. Default: 128
|
||||
# CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority.
|
||||
# Default: Medium
|
||||
# CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode. Default:
|
||||
# 4-bit transfer mode.
|
||||
# CONFIG_MMCSD_MMCSUPPORT
|
||||
# Enable support for MMC cards
|
||||
# CONFIG_MMCSD_HAVECARDDETECT
|
||||
# SDIO driver card detection is 100% accurate
|
||||
#
|
||||
CONFIG_SDIO_DMA=y
|
||||
#CONFIG_SDIO_PRI=128
|
||||
#CONFIG_SDIO_DMAPRIO
|
||||
#CONFIG_SDIO_WIDTH_D1_ONLY
|
||||
CONFIG_MMCSD_MMCSUPPORT=n
|
||||
CONFIG_MMCSD_HAVECARDDETECT=n
|
||||
|
||||
#
|
||||
# TCP/IP and UDP support via uIP
|
||||
# CONFIG_NET - Enable or disable all network features
|
||||
# CONFIG_NET_IPv6 - Build in support for IPv6
|
||||
# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
|
||||
# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
|
||||
# CONFIG_NET_BUFSIZE - uIP buffer size
|
||||
# CONFIG_NET_TCP - TCP support on or off
|
||||
# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
|
||||
# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
|
||||
# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
|
||||
# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
|
||||
# accept() is called. The size of the backlog is selected when listen() is called.
|
||||
# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
|
||||
# CONFIG_NET_UDP - UDP support on or off
|
||||
# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
|
||||
# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
|
||||
# CONFIG_NET_ICMP - ICMP ping response support on or off
|
||||
# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
|
||||
# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
|
||||
# CONFIG_NET_STATISTICS - uIP statistics on or off
|
||||
# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
|
||||
# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
|
||||
# CONFIG_NET_BROADCAST - Broadcast support
|
||||
# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
|
||||
#
|
||||
CONFIG_NET=n
|
||||
CONFIG_NET_IPv6=n
|
||||
CONFIG_NSOCKET_DESCRIPTORS=0
|
||||
CONFIG_NET_SOCKOPTS=y
|
||||
CONFIG_NET_BUFSIZE=420
|
||||
CONFIG_NET_TCP=n
|
||||
CONFIG_NET_TCP_CONNS=40
|
||||
CONFIG_NET_MAX_LISTENPORTS=40
|
||||
CONFIG_NET_UDP=n
|
||||
CONFIG_NET_UDP_CHECKSUMS=y
|
||||
#CONFIG_NET_UDP_CONNS=10
|
||||
CONFIG_NET_ICMP=n
|
||||
CONFIG_NET_ICMP_PING=n
|
||||
#CONFIG_NET_PINGADDRCONF=0
|
||||
CONFIG_NET_STATISTICS=y
|
||||
#CONFIG_NET_RECEIVE_WINDOW=
|
||||
#CONFIG_NET_ARPTAB_SIZE=8
|
||||
CONFIG_NET_BROADCAST=n
|
||||
#CONFIG_NET_FWCACHE_SIZE=2
|
||||
|
||||
#
|
||||
# UIP Network Utilities
|
||||
# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
|
||||
# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
|
||||
#
|
||||
CONFIG_NET_DHCP_LIGHT=n
|
||||
CONFIG_NET_RESOLV_ENTRIES=4
|
||||
|
||||
#
|
||||
# USB Device Configuration
|
||||
#
|
||||
# CONFIG_USBDEV
|
||||
# Enables USB device support
|
||||
# CONFIG_USBDEV_ISOCHRONOUS
|
||||
# Build in extra support for isochronous endpoints
|
||||
# CONFIG_USBDEV_DUALSPEED
|
||||
# Hardware handles high and full speed operation (USB 2.0)
|
||||
# CONFIG_USBDEV_SELFPOWERED
|
||||
# Will cause USB features to indicate that the device is
|
||||
# self-powered
|
||||
# CONFIG_USBDEV_MAXPOWER
|
||||
# Maximum power consumption in mA
|
||||
# CONFIG_USBDEV_TRACE
|
||||
# Enables USB tracing for debug
|
||||
# CONFIG_USBDEV_TRACE_NRECORDS
|
||||
# Number of trace entries to remember
|
||||
#
|
||||
CONFIG_USBDEV=n
|
||||
CONFIG_USBDEV_ISOCHRONOUS=n
|
||||
CONFIG_USBDEV_DUALSPEED=n
|
||||
CONFIG_USBDEV_SELFPOWERED=y
|
||||
CONFIG_USBDEV_REMOTEWAKEUP=n
|
||||
CONFIG_USBDEV_MAXPOWER=100
|
||||
CONFIG_USBDEV_TRACE=n
|
||||
CONFIG_USBDEV_TRACE_NRECORDS=128
|
||||
|
||||
#
|
||||
# USB Serial Device Configuration
|
||||
#
|
||||
# CONFIG_USBSER
|
||||
# Enable compilation of the USB serial driver
|
||||
# CONFIG_USBSER_EPINTIN
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# interrupt IN operation
|
||||
# CONFIG_USBSER_EPBULKOUT
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# bulk OUT operation
|
||||
# CONFIG_USBSER_EPBULKIN
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# bulk IN operation
|
||||
# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
|
||||
# The number of write/read requests that can be in flight
|
||||
# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
|
||||
# The vendor ID code/string
|
||||
# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
|
||||
# The product ID code/string
|
||||
# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
|
||||
# Size of the serial receive/transmit buffers
|
||||
#
|
||||
CONFIG_USBSER=n
|
||||
CONFIG_USBSER_EPINTIN=1
|
||||
CONFIG_USBSER_EPBULKOUT=2
|
||||
CONFIG_USBSER_EPBULKIN=3
|
||||
CONFIG_USBSER_NWRREQS=4
|
||||
CONFIG_USBSER_NRDREQS=4
|
||||
CONFIG_USBSER_VENDORID=0x067b
|
||||
CONFIG_USBSER_PRODUCTID=0x2303
|
||||
CONFIG_USBSER_VENDORSTR="Nuttx"
|
||||
CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
|
||||
CONFIG_USBSER_RXBUFSIZE=512
|
||||
CONFIG_USBSER_TXBUFSIZE=512
|
||||
|
||||
#
|
||||
# USB Storage Device Configuration
|
||||
#
|
||||
# CONFIG_USBSTRG
|
||||
# Enable compilation of the USB storage driver
|
||||
# CONFIG_USBSTRG_EP0MAXPACKET
|
||||
# Max packet size for endpoint 0
|
||||
# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
|
||||
# The logical 7-bit address of a hardware endpoints that support
|
||||
# bulk OUT and IN operations
|
||||
# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
|
||||
# The number of write/read requests that can be in flight
|
||||
# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
|
||||
# The size of the buffer in each write/read request. This
|
||||
# value needs to be at least as large as the endpoint
|
||||
# maxpacket and ideally as large as a block device sector.
|
||||
# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
|
||||
# The vendor ID code/string
|
||||
# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
|
||||
# The product ID code/string
|
||||
# CONFIG_USBSTRG_REMOVABLE
|
||||
# Select if the media is removable
|
||||
#
|
||||
CONFIG_USBSTRG=n
|
||||
CONFIG_USBSTRG_EP0MAXPACKET=64
|
||||
CONFIG_USBSTRG_EPBULKOUT=2
|
||||
CONFIG_USBSTRG_EPBULKIN=5
|
||||
CONFIG_USBSTRG_NRDREQS=2
|
||||
CONFIG_USBSTRG_NWRREQS=2
|
||||
CONFIG_USBSTRG_BULKINREQLEN=256
|
||||
CONFIG_USBSTRG_BULKOUTREQLEN=256
|
||||
CONFIG_USBSTRG_VENDORID=0x584e
|
||||
CONFIG_USBSTRG_VENDORSTR="NuttX"
|
||||
CONFIG_USBSTRG_PRODUCTID=0x5342
|
||||
CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
|
||||
CONFIG_USBSTRG_VERSIONNO=0x0399
|
||||
CONFIG_USBSTRG_REMOVABLE=y
|
||||
|
||||
#
|
||||
# Settings for examples/uip
|
||||
#
|
||||
CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_UIP_DHCPC=n
|
||||
|
||||
#
|
||||
# Settings for examples/nettest
|
||||
CONFIG_EXAMPLE_NETTEST_SERVER=n
|
||||
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
|
||||
CONFIG_EXAMPLE_NETTEST_NOMAC=n
|
||||
CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
|
||||
|
||||
#
|
||||
# Settings for examples/ostest
|
||||
#
|
||||
CONFIG_EXAMPLES_OSTEST_LOOPS=1
|
||||
CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
|
||||
CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
|
||||
|
||||
#
|
||||
# Settings for apps/nshlib
|
||||
#
|
||||
# CONFIG_NSH_BUILTIN_APPS - Support external registered,
|
||||
# "named" applications that can be executed from the NSH
|
||||
# command line (see apps/README.txt for more information).
|
||||
# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
|
||||
# CONFIG_NSH_STRERROR - Use strerror(errno)
|
||||
# CONFIG_NSH_LINELEN - Maximum length of one command line
|
||||
# CONFIG_NSH_STACKSIZE - Stack size to use for new threads.
|
||||
# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
|
||||
# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
|
||||
# CONFIG_NSH_DISABLEBG - Disable background commands
|
||||
# CONFIG_NSH_ROMFSETC - Use startup script in /etc
|
||||
# CONFIG_NSH_CONSOLE - Use serial console front end
|
||||
# CONFIG_NSH_TELNET - Use telnetd console front end
|
||||
# CONFIG_NSH_ARCHINIT - Platform provides architecture
|
||||
# specific initialization (nsh_archinitialize()).
|
||||
#
|
||||
# If CONFIG_NSH_TELNET is selected:
|
||||
# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
|
||||
# CONFIG_NSH_DHCPC - Obtain address using DHCP
|
||||
# CONFIG_NSH_IPADDR - Provides static IP address
|
||||
# CONFIG_NSH_DRIPADDR - Provides static router IP address
|
||||
# CONFIG_NSH_NETMASK - Provides static network mask
|
||||
# CONFIG_NSH_NOMAC - Use a bogus MAC address
|
||||
#
|
||||
# If CONFIG_NSH_ROMFSETC is selected:
|
||||
# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
|
||||
# CONFIG_NSH_INITSCRIPT - Relative path to init script
|
||||
# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
|
||||
# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
|
||||
# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
|
||||
# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
|
||||
# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
|
||||
# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
|
||||
#
|
||||
CONFIG_NSH_BUILTIN_APPS=n
|
||||
CONFIG_NSH_FILEIOSIZE=512
|
||||
CONFIG_NSH_STRERROR=n
|
||||
CONFIG_NSH_LINELEN=64
|
||||
CONFIG_NSH_STACKSIZE=2048
|
||||
CONFIG_NSH_NESTDEPTH=3
|
||||
CONFIG_NSH_DISABLESCRIPT=n
|
||||
CONFIG_NSH_DISABLEBG=n
|
||||
CONFIG_NSH_ROMFSETC=n
|
||||
CONFIG_NSH_CONSOLE=y
|
||||
CONFIG_NSH_TELNET=n
|
||||
CONFIG_NSH_ARCHINIT=y
|
||||
CONFIG_NSH_IOBUFFER_SIZE=512
|
||||
CONFIG_NSH_DHCPC=n
|
||||
CONFIG_NSH_NOMAC=n
|
||||
CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_NSH_ROMFSMOUNTPT="/etc"
|
||||
CONFIG_NSH_INITSCRIPT="init.d/rcS"
|
||||
CONFIG_NSH_ROMFSDEVNO=0
|
||||
CONFIG_NSH_ROMFSSECTSIZE=64
|
||||
CONFIG_NSH_FATDEVNO=1
|
||||
CONFIG_NSH_FATSECTSIZE=512
|
||||
CONFIG_NSH_FATNSECTORS=1024
|
||||
CONFIG_NSH_FATMOUNTPT=/tmp
|
||||
|
||||
#
|
||||
# Architecture-specific NSH options
|
||||
#
|
||||
CONFIG_NSH_MMCSDSPIPORTNO=0
|
||||
CONFIG_NSH_MMCSDSLOTNO=0
|
||||
CONFIG_NSH_MMCSDMINOR=0
|
||||
|
||||
#
|
||||
# Settings for examples/usbserial
|
||||
#
|
||||
# CONFIG_EXAMPLES_USBSERIAL_INONLY
|
||||
# Only verify IN (device-to-host) data transfers. Default: both
|
||||
# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
|
||||
# Only verify OUT (host-to-device) data transfers. Default: both
|
||||
# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
|
||||
# Send only small, single packet messages. Default: Send large and small.
|
||||
# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
|
||||
# Send only large, multi-packet messages. Default: Send large and small.
|
||||
#
|
||||
CONFIG_EXAMPLES_USBSERIAL_INONLY=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
|
||||
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
|
||||
|
||||
#
|
||||
# Stack and heap information
|
||||
#
|
||||
# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
|
||||
# operation from FLASH but must copy initialized .data sections to RAM.
|
||||
# (should also be =n for the Hy-Mini STM32v which always runs from flash)
|
||||
# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH
|
||||
# but copy themselves entirely into RAM for better performance.
|
||||
# CONFIG_CUSTOM_STACK - The up_ implementation will handle
|
||||
# all stack operations outside of the nuttx model.
|
||||
# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
|
||||
# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
|
||||
# This is the thread that (1) performs the inital boot of the system up
|
||||
# to the point where user_start() is spawned, and (2) there after is the
|
||||
# IDLE thread that executes only when there is no other thread ready to
|
||||
# run.
|
||||
# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
|
||||
# for the main user thread that begins at the user_start() entry point.
|
||||
# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
|
||||
# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
|
||||
# CONFIG_HEAP_BASE - The beginning of the heap
|
||||
# CONFIG_HEAP_SIZE - The size of the heap
|
||||
#
|
||||
CONFIG_BOOT_RUNFROMFLASH=n
|
||||
CONFIG_BOOT_COPYTORAM=n
|
||||
CONFIG_CUSTOM_STACK=n
|
||||
CONFIG_STACK_POINTER=
|
||||
CONFIG_IDLETHREAD_STACKSIZE=1024
|
||||
CONFIG_USERMAIN_STACKSIZE=2048
|
||||
CONFIG_PTHREAD_STACK_MIN=256
|
||||
CONFIG_PTHREAD_STACK_DEFAULT=2048
|
||||
CONFIG_HEAP_BASE=
|
||||
CONFIG_HEAP_SIZE=
|
|
@ -0,0 +1,112 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/nsh/ld.script
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
|
||||
* 64Kb of SRAM beginning at address 0x2000:0000. When booting from FLASH,
|
||||
* FLASH memory is aliased to address 0x0000:0000 where the code expects to
|
||||
* begin execution by jumping to the entry point in the 0x0800:0000 address
|
||||
* range.
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x08000000, LENGTH = 512K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} >sram
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
|
@ -0,0 +1,111 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/nsh/ld.script.dfu
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
|
||||
* 64Kb of SRAM beginning at address 0x2000:0000. Here we assume that the
|
||||
* Hy-Mini STM32v's DFU bootloader is being used. In that case, the corrct
|
||||
* load .text load address is 0x08003000 (leaving 464Kb).
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x08003000, LENGTH = 464K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} >sram
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
|
@ -0,0 +1,47 @@
|
|||
#!/bin/bash
|
||||
# configs/hymini-stm32v/dfu/setenv.sh
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
|
||||
if [ "$(basename $0)" = "setenv.sh" ] ; then
|
||||
echo "You must source this script, not run it!" 1>&2
|
||||
exit 1
|
||||
fi
|
||||
|
||||
if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi
|
||||
|
||||
WD=`pwd`
|
||||
export RIDE_BIN="/cygdrive/c/Program Files/Raisonance/Ride/arm-gcc/bin"
|
||||
export BUILDROOT_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
|
||||
export PATH="${BUILDROOT_BIN}:${RIDE_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
|
||||
|
||||
echo "PATH : ${PATH}"
|
|
@ -0,0 +1,174 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/nsh2/Make.defs
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include ${TOPDIR}/.config
|
||||
|
||||
# Setup for the selected toolchain
|
||||
|
||||
ifeq ($(CONFIG_STM32_DFU),y)
|
||||
LDSCRIPT = ld.script.dfu
|
||||
else
|
||||
LDSCRIPT = ld.script
|
||||
endif
|
||||
|
||||
ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
|
||||
# CodeSourcery under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
|
||||
# CodeSourcery under Linux
|
||||
CROSSDEV = arm-none-eabi-
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -O2
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_DEVKITARM),y)
|
||||
# devkitARM under Windows
|
||||
CROSSDEV = arm-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_RAISONANCE),y)
|
||||
# Raisonance RIDE7 under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_BUILDROOT),y)
|
||||
# NuttX buildroot under Linux or Cygwin
|
||||
CROSSDEV = arm-elf-
|
||||
ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -Os
|
||||
endif
|
||||
|
||||
ifeq ($(WINTOOL),y)
|
||||
# Windows-native toolchains
|
||||
DIRLINK = $(TOPDIR)/tools/winlink.sh
|
||||
DIRUNLINK = $(TOPDIR)/tools/unlink.sh
|
||||
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
|
||||
ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh2/$(LDSCRIPT)}"
|
||||
MAXOPTIMIZATION = -O2
|
||||
else
|
||||
# Linux/Cygwin-native toolchain
|
||||
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
||||
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
||||
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh2/$(LDSCRIPT)
|
||||
endif
|
||||
|
||||
CC = $(CROSSDEV)gcc
|
||||
CXX = $(CROSSDEV)g++
|
||||
CPP = $(CROSSDEV)gcc -E
|
||||
LD = $(CROSSDEV)ld
|
||||
AR = $(CROSSDEV)ar rcs
|
||||
NM = $(CROSSDEV)nm
|
||||
OBJCOPY = $(CROSSDEV)objcopy
|
||||
OBJDUMP = $(CROSSDEV)objdump
|
||||
|
||||
ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
|
||||
ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
|
||||
|
||||
ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
|
||||
ARCHOPTIMIZATION = -g
|
||||
else
|
||||
ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
|
||||
endif
|
||||
|
||||
ARCHCFLAGS = -fno-builtin
|
||||
ARCHCXXFLAGS = -fno-builtin -fno-exceptions
|
||||
ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
|
||||
ARCHWARNINGSXX = -Wall -Wshadow
|
||||
ARCHDEFINES =
|
||||
ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
|
||||
|
||||
CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
|
||||
CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
|
||||
CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
|
||||
AFLAGS = $(CFLAGS) -D__ASSEMBLY__
|
||||
|
||||
NXFLATLDFLAGS1 = -r -d -warn-common
|
||||
NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
|
||||
LDNXFLATFLAGS = -e main -s 2048
|
||||
|
||||
OBJEXT = .o
|
||||
LIBEXT = .a
|
||||
EXEEXT =
|
||||
|
||||
ifneq ($(CROSSDEV),arm-elf-)
|
||||
LDFLAGS += -nostartfiles -nodefaultlibs
|
||||
endif
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
LDFLAGS += -g
|
||||
endif
|
||||
|
||||
define PREPROCESS
|
||||
@echo "CPP: $1->$2"
|
||||
@$(CPP) $(CPPFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILE
|
||||
@echo "CC: $1"
|
||||
@$(CC) -c $(CFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILEXX
|
||||
@echo "CXX: $1"
|
||||
@$(CXX) -c $(CXXFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ASSEMBLE
|
||||
@echo "AS: $1"
|
||||
@$(CC) -c $(AFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ARCHIVE
|
||||
echo "AR: $2"; \
|
||||
$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
|
||||
endef
|
||||
|
||||
define CLEAN
|
||||
@rm -f *.o *.a
|
||||
endef
|
||||
|
||||
HOSTCC = gcc
|
||||
HOSTINCLUDES = -I.
|
||||
HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
|
||||
HOSTLDFLAGS =
|
||||
|
|
@ -0,0 +1,52 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/nsh2/appconfig
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
# Path to example in apps/examples containing the user_start entry point
|
||||
|
||||
CONFIGURED_APPS += examples/nsh
|
||||
|
||||
# The NSH application library
|
||||
|
||||
CONFIGURED_APPS += nshlib
|
||||
|
||||
# The NX and NXHELLO examples configured as an NX built-in commands
|
||||
|
||||
# CONFIGURED_APPS += examples/nx
|
||||
CONFIGURED_APPS += examples/usbstorage
|
||||
CONFIGURED_APPS += examples/nximage
|
||||
CONFIGURED_APPS += examples/touchscreen
|
||||
CONFIGURED_APPS += examples/lcdtest
|
||||
CONFIGURED_APPS += examples/buttons
|
||||
CONFIGURED_APPS += examples/tc_test
|
File diff suppressed because it is too large
Load Diff
|
@ -0,0 +1,112 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/nsh2/ld.script
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F103VCT6 has 256Kb of FLASH beginning at address 0x0800:0000 and
|
||||
* 48Kb of SRAM beginning at address 0x2000:0000. When booting from FLASH,
|
||||
* FLASH memory is aliased to address 0x0000:0000 where the code expects to
|
||||
* begin execution by jumping to the entry point in the 0x0800:0000 address
|
||||
* range.
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x08000000, LENGTH = 256K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 48K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} >sram
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
|
@ -0,0 +1,111 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/nsh2/ld.script.dfu
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
|
||||
* 64Kb of SRAM beginning at address 0x2000:0000. Here we assume that the
|
||||
* Hy-Mini STM32v's DFU bootloader is being used. In that case, the corrct
|
||||
* load .text load address is 0x08003000 (leaving 464Kb).
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x08003000, LENGTH = 464K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} >sram
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
|
@ -0,0 +1,67 @@
|
|||
#!/bin/bash
|
||||
# configs/hymini-stm32v/nsh2/setenv.sh
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
|
||||
if [ "$_" = "$0" ] ; then
|
||||
echo "You must source this script, not run it!" 1>&2
|
||||
exit 1
|
||||
fi
|
||||
|
||||
WD=`pwd`
|
||||
if [ ! -x "setenv.sh" ]; then
|
||||
echo "This script must be executed from the top-level NuttX build directory"
|
||||
exit 1
|
||||
fi
|
||||
|
||||
if [ -z "${PATH_ORIG}" ]; then
|
||||
export PATH_ORIG="${PATH}"
|
||||
fi
|
||||
|
||||
# This the Cygwin path to the location where I installed the RIDE
|
||||
# toolchain under windows. You will also have to edit this if you install
|
||||
# the RIDE toolchain in any other location
|
||||
#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/Raisonance/Ride/arm-gcc/bin"
|
||||
|
||||
# This the Cygwin path to the location where I installed the CodeSourcery
|
||||
# toolchain under windows. You will also have to edit this if you install
|
||||
# the CodeSourcery toolchain in any other location
|
||||
export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin"
|
||||
|
||||
# This the Cygwin path to the location where I build the buildroot
|
||||
# toolchain.
|
||||
#export TOOLCHAIN_BIN="${WD}/../misc/buildroot/build_arm_nofpu/staging_dir/bin"
|
||||
|
||||
# Add the path to the toolchain to the PATH varialble
|
||||
export PATH="${TOOLCHAIN_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
|
||||
|
||||
echo "PATH : ${PATH}"
|
|
@ -0,0 +1,174 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/nx/Make.defs
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include ${TOPDIR}/.config
|
||||
|
||||
# Setup for the selected toolchain
|
||||
|
||||
ifeq ($(CONFIG_STM32_DFU),y)
|
||||
LDSCRIPT = ld.script.dfu
|
||||
else
|
||||
LDSCRIPT = ld.script
|
||||
endif
|
||||
|
||||
ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
|
||||
# CodeSourcery under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
|
||||
# CodeSourcery under Linux
|
||||
CROSSDEV = arm-none-eabi-
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -O2
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_DEVKITARM),y)
|
||||
# devkitARM under Windows
|
||||
CROSSDEV = arm-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_RAISONANCE),y)
|
||||
# Raisonance RIDE7 under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_BUILDROOT),y)
|
||||
# NuttX buildroot under Linux or Cygwin
|
||||
CROSSDEV = arm-elf-
|
||||
ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -Os
|
||||
endif
|
||||
|
||||
ifeq ($(WINTOOL),y)
|
||||
# Windows-native toolchains
|
||||
DIRLINK = $(TOPDIR)/tools/winlink.sh
|
||||
DIRUNLINK = $(TOPDIR)/tools/unlink.sh
|
||||
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
|
||||
ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nx/$(LDSCRIPT)}"
|
||||
MAXOPTIMIZATION = -O2
|
||||
else
|
||||
# Linux/Cygwin-native toolchain
|
||||
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
||||
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
||||
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nx/$(LDSCRIPT)
|
||||
endif
|
||||
|
||||
CC = $(CROSSDEV)gcc
|
||||
CXX = $(CROSSDEV)g++
|
||||
CPP = $(CROSSDEV)gcc -E
|
||||
LD = $(CROSSDEV)ld
|
||||
AR = $(CROSSDEV)ar rcs
|
||||
NM = $(CROSSDEV)nm
|
||||
OBJCOPY = $(CROSSDEV)objcopy
|
||||
OBJDUMP = $(CROSSDEV)objdump
|
||||
|
||||
ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
|
||||
ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
|
||||
|
||||
ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
|
||||
ARCHOPTIMIZATION = -g
|
||||
else
|
||||
ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
|
||||
endif
|
||||
|
||||
ARCHCFLAGS = -fno-builtin
|
||||
ARCHCXXFLAGS = -fno-builtin -fno-exceptions
|
||||
ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
|
||||
ARCHWARNINGSXX = -Wall -Wshadow
|
||||
ARCHDEFINES =
|
||||
ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
|
||||
|
||||
CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
|
||||
CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
|
||||
CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
|
||||
AFLAGS = $(CFLAGS) -D__ASSEMBLY__
|
||||
|
||||
NXFLATLDFLAGS1 = -r -d -warn-common
|
||||
NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
|
||||
LDNXFLATFLAGS = -e main -s 2048
|
||||
|
||||
OBJEXT = .o
|
||||
LIBEXT = .a
|
||||
EXEEXT =
|
||||
|
||||
ifneq ($(CROSSDEV),arm-elf-)
|
||||
LDFLAGS += -nostartfiles -nodefaultlibs
|
||||
endif
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
LDFLAGS += -g
|
||||
endif
|
||||
|
||||
define PREPROCESS
|
||||
@echo "CPP: $1->$2"
|
||||
@$(CPP) $(CPPFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILE
|
||||
@echo "CC: $1"
|
||||
@$(CC) -c $(CFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILEXX
|
||||
@echo "CXX: $1"
|
||||
@$(CXX) -c $(CXXFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ASSEMBLE
|
||||
@echo "AS: $1"
|
||||
@$(CC) -c $(AFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ARCHIVE
|
||||
echo "AR: $2"; \
|
||||
$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
|
||||
endef
|
||||
|
||||
define CLEAN
|
||||
@rm -f *.o *.a
|
||||
endef
|
||||
|
||||
HOSTCC = gcc
|
||||
HOSTINCLUDES = -I.
|
||||
HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
|
||||
HOSTLDFLAGS =
|
||||
|
|
@ -0,0 +1,39 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/nx/appconfig
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
# Path to example in apps/examples containing the user_start entry point
|
||||
|
||||
CONFIGURED_APPS += examples/nx
|
||||
|
File diff suppressed because it is too large
Load Diff
|
@ -0,0 +1,112 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/nx/ld.script
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F103VCT6 has 256Kb of FLASH beginning at address 0x0800:0000 and
|
||||
* 48Kb of SRAM beginning at address 0x2000:0000. When booting from FLASH,
|
||||
* FLASH memory is aliased to address 0x0000:0000 where the code expects to
|
||||
* begin execution by jumping to the entry point in the 0x0800:0000 address
|
||||
* range.
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x08000000, LENGTH = 256K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 48K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} >sram
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
|
@ -0,0 +1,111 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/nx/ld.script.dfu
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
|
||||
* 64Kb of SRAM beginning at address 0x2000:0000. Here we assume that the
|
||||
* Hy-Mini STM32v's DFU bootloader is being used. In that case, the corrct
|
||||
* load .text load address is 0x08003000 (leaving 464Kb).
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x08003000, LENGTH = 464K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} >sram
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
|
@ -0,0 +1,62 @@
|
|||
#!/bin/bash
|
||||
# configs/hymini-stm32v/nx/setenv.sh
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
|
||||
if [ "$_" = "$0" ] ; then
|
||||
echo "You must source this script, not run it!" 1>&2
|
||||
exit 1
|
||||
fi
|
||||
|
||||
WD=`pwd`
|
||||
if [ ! -x "setenv.sh" ]; then
|
||||
echo "This script must be executed from the top-level NuttX build directory"
|
||||
exit 1
|
||||
fi
|
||||
|
||||
if [ -z "${PATH_ORIG}" ]; then
|
||||
export PATH_ORIG="${PATH}"
|
||||
fi
|
||||
|
||||
# This the Cygwin path to the location where I installed the CodeSourcery
|
||||
# toolchain under windows. You will also have to edit this if you install
|
||||
# the CodeSourcery toolchain in any other location
|
||||
export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin"
|
||||
|
||||
# This the Cygwin path to the location where I build the buildroot
|
||||
# toolchain.
|
||||
#export TOOLCHAIN_BIN="${WD}/../misc/buildroot/build_arm_nofpu/staging_dir/bin"
|
||||
|
||||
# Add the path to the toolchain to the PATH varialble
|
||||
export PATH="${TOOLCHAIN_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
|
||||
|
||||
echo "PATH : ${PATH}"
|
|
@ -0,0 +1,176 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/nxlines/Make.defs
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include ${TOPDIR}/.config
|
||||
|
||||
# Setup for the selected toolchain
|
||||
|
||||
ifeq ($(CONFIG_STM32_DFU),y)
|
||||
LDSCRIPT = ld.script.dfu
|
||||
else
|
||||
LDSCRIPT = ld.script
|
||||
endif
|
||||
|
||||
ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
|
||||
# CodeSourcery under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -O1
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
|
||||
# CodeSourcery under Linux
|
||||
CROSSDEV = arm-none-eabi-
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -O1
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_DEVKITARM),y)
|
||||
# devkitARM under Windows
|
||||
CROSSDEV = arm-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -O2
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_RAISONANCE),y)
|
||||
# Raisonance RIDE7 under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -O2
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_BUILDROOT),y)
|
||||
# NuttX buildroot under Linux or Cygwin
|
||||
CROSSDEV = arm-elf-
|
||||
ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -Os
|
||||
endif
|
||||
|
||||
ifeq ($(WINTOOL),y)
|
||||
# Windows-native toolchains
|
||||
DIRLINK = $(TOPDIR)/tools/winlink.sh
|
||||
DIRUNLINK = $(TOPDIR)/tools/unlink.sh
|
||||
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
|
||||
ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nxlines/$(LDSCRIPT)}"
|
||||
else
|
||||
# Linux/Cygwin-native toolchain
|
||||
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
||||
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
||||
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nxlines/$(LDSCRIPT)
|
||||
endif
|
||||
|
||||
CC = $(CROSSDEV)gcc
|
||||
CXX = $(CROSSDEV)g++
|
||||
CPP = $(CROSSDEV)gcc -E
|
||||
LD = $(CROSSDEV)ld
|
||||
AR = $(CROSSDEV)ar rcs
|
||||
NM = $(CROSSDEV)nm
|
||||
OBJCOPY = $(CROSSDEV)objcopy
|
||||
OBJDUMP = $(CROSSDEV)objdump
|
||||
|
||||
ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
|
||||
ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
|
||||
|
||||
ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
|
||||
ARCHOPTIMIZATION = -g
|
||||
else
|
||||
ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
|
||||
endif
|
||||
|
||||
ARCHCFLAGS = -fno-builtin
|
||||
ARCHCXXFLAGS = -fno-builtin -fno-exceptions
|
||||
ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
|
||||
ARCHWARNINGSXX = -Wall -Wshadow
|
||||
ARCHDEFINES =
|
||||
ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
|
||||
|
||||
CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
|
||||
CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
|
||||
CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
|
||||
AFLAGS = $(CFLAGS) -D__ASSEMBLY__
|
||||
|
||||
NXFLATLDFLAGS1 = -r -d -warn-common
|
||||
NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
|
||||
LDNXFLATFLAGS = -e main -s 2048
|
||||
|
||||
OBJEXT = .o
|
||||
LIBEXT = .a
|
||||
EXEEXT =
|
||||
|
||||
ifneq ($(CROSSDEV),arm-elf-)
|
||||
LDFLAGS += -nostartfiles -nodefaultlibs
|
||||
endif
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
LDFLAGS += -g
|
||||
endif
|
||||
|
||||
define PREPROCESS
|
||||
@echo "CPP: $1->$2"
|
||||
@$(CPP) $(CPPFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILE
|
||||
@echo "CC: $1"
|
||||
@$(CC) -c $(CFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILEXX
|
||||
@echo "CXX: $1"
|
||||
@$(CXX) -c $(CXXFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ASSEMBLE
|
||||
@echo "AS: $1"
|
||||
@$(CC) -c $(AFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ARCHIVE
|
||||
echo "AR: $2"; \
|
||||
$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
|
||||
endef
|
||||
|
||||
define CLEAN
|
||||
@rm -f *.o *.a
|
||||
endef
|
||||
|
||||
HOSTCC = gcc
|
||||
HOSTINCLUDES = -I.
|
||||
HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
|
||||
HOSTLDFLAGS =
|
||||
|
|
@ -0,0 +1,39 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/nxlines/appconfig
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
# Path to example in apps/examples containing the user_start entry point
|
||||
|
||||
CONFIGURED_APPS += examples/nxlines
|
||||
|
File diff suppressed because it is too large
Load Diff
|
@ -0,0 +1,112 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/nxlines/ld.script
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F103VCT6 has 256Kb of FLASH beginning at address 0x0800:0000 and
|
||||
* 48Kb of SRAM beginning at address 0x2000:0000. When booting from FLASH,
|
||||
* FLASH memory is aliased to address 0x0000:0000 where the code expects to
|
||||
* begin execution by jumping to the entry point in the 0x0800:0000 address
|
||||
* range.
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x08000000, LENGTH = 256K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 48K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} >sram
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
|
@ -0,0 +1,111 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/nxlines/ld.script.dfu
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
|
||||
* 64Kb of SRAM beginning at address 0x2000:0000. Here we assume that the
|
||||
* Hy-Mini STM32v's DFU bootloader is being used. In that case, the corrct
|
||||
* load .text load address is 0x08003000 (leaving 464Kb).
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x08003000, LENGTH = 464K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} >sram
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
|
@ -0,0 +1,53 @@
|
|||
#!/bin/bash
|
||||
# configs/hymini-stm32v/nxlines/setenv.sh
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
|
||||
if [ "$_" = "$0" ] ; then
|
||||
echo "You must source this script, not run it!"
|
||||
exit 1
|
||||
fi
|
||||
|
||||
WD=`pwd`
|
||||
if [ ! -x "setenv.sh" ]; then
|
||||
echo "This script must be executed from the top-level NuttX build directory"
|
||||
exit 1
|
||||
fi
|
||||
|
||||
if [ -z "${PATH_ORIG}" ]; then
|
||||
export PATH_ORIG="${PATH}"
|
||||
fi
|
||||
|
||||
export BUILDROOT_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
|
||||
export PATH="${BUILDROOT_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
|
||||
|
||||
echo "PATH : ${PATH}"
|
|
@ -0,0 +1,102 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/src/Makefile
|
||||
#
|
||||
# Copyright (C) 2009-2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
# Laurent Latil <laurent@latil.nom.fr>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
-include $(TOPDIR)/Make.defs
|
||||
|
||||
CFLAGS += -I$(TOPDIR)/sched
|
||||
|
||||
ASRCS =
|
||||
AOBJS = $(ASRCS:.S=$(OBJEXT))
|
||||
|
||||
CSRCS = up_boot.c up_leds.c up_buttons.c up_spi.c up_usbdev.c
|
||||
|
||||
ifeq ($(CONFIG_NX_LCDDRIVER),y)
|
||||
CSRCS += ssd1289.c
|
||||
endif
|
||||
|
||||
ifeq ($(CONFIG_NSH_ARCHINIT),y)
|
||||
CSRCS += up_nsh.c
|
||||
endif
|
||||
|
||||
ifeq ($(CONFIG_INPUT),y)
|
||||
CSRCS += up_ts.c
|
||||
endif
|
||||
|
||||
ifeq ($(CONFIG_USBSTRG),y)
|
||||
CSRCS += up_usbstrg.c
|
||||
endif
|
||||
|
||||
COBJS = $(CSRCS:.c=$(OBJEXT))
|
||||
|
||||
SRCS = $(ASRCS) $(CSRCS)
|
||||
OBJS = $(AOBJS) $(COBJS)
|
||||
|
||||
ARCH_SRCDIR = $(TOPDIR)/arch/$(CONFIG_ARCH)/src
|
||||
ifeq ($(WINTOOL),y)
|
||||
CFLAGS += -I "${shell cygpath -w $(ARCH_SRCDIR)/chip}" \
|
||||
-I "${shell cygpath -w $(ARCH_SRCDIR)/common}" \
|
||||
-I "${shell cygpath -w $(ARCH_SRCDIR)/armv7-m}"
|
||||
else
|
||||
CFLAGS += -I$(ARCH_SRCDIR)/chip -I$(ARCH_SRCDIR)/common -I$(ARCH_SRCDIR)/armv7-m
|
||||
endif
|
||||
|
||||
all: libboard$(LIBEXT)
|
||||
|
||||
$(AOBJS): %$(OBJEXT): %.S
|
||||
$(call ASSEMBLE, $<, $@)
|
||||
|
||||
$(COBJS) $(LINKOBJS): %$(OBJEXT): %.c
|
||||
$(call COMPILE, $<, $@)
|
||||
|
||||
libboard$(LIBEXT): $(OBJS)
|
||||
@( for obj in $(OBJS) ; do \
|
||||
$(call ARCHIVE, $@, $${obj}); \
|
||||
done ; )
|
||||
|
||||
.depend: Makefile $(SRCS)
|
||||
@$(MKDEP) $(CC) -- $(CFLAGS) -- $(SRCS) >Make.dep
|
||||
@touch $@
|
||||
|
||||
depend: .depend
|
||||
|
||||
clean:
|
||||
@rm -f libboard$(LIBEXT) *~ .*.swp
|
||||
$(call CLEAN)
|
||||
|
||||
distclean: clean
|
||||
@rm -f Make.dep .depend
|
||||
|
||||
-include Make.dep
|
|
@ -0,0 +1 @@
|
|||
This directory contains drivers unique to the HY-MiniSTM32V development board.
|
|
@ -0,0 +1,153 @@
|
|||
/************************************************************************************
|
||||
* configs/hymini-stm32v/src/hymini_stm32v-internal.h
|
||||
* arch/arm/src/board/hymini_stm32v-internal.h
|
||||
*
|
||||
* Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
* Laurent Latil <laurent@latil.nom.fr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
#ifndef __CONFIGS_HYMINI_STM32V_INTERNAL_H
|
||||
#define __CONFIGS_HYMINI_STM32V_INTERNAL_H
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
#include <nuttx/compiler.h>
|
||||
#include <stdint.h>
|
||||
|
||||
/************************************************************************************
|
||||
* Definitions
|
||||
************************************************************************************/
|
||||
|
||||
/* How many SPI modules does this chip support? The LM3S6918 supports 2 SPI
|
||||
* modules (others may support more -- in such case, the following must be
|
||||
* expanded).
|
||||
*/
|
||||
|
||||
#if STM32_NSPI < 1
|
||||
# undef CONFIG_STM32_SPI1
|
||||
# undef CONFIG_STM32_SPI2
|
||||
#elif STM32_NSPI < 2
|
||||
# undef CONFIG_STM32_SPI2
|
||||
#endif
|
||||
|
||||
/* GPIOs **************************************************************/
|
||||
/* LEDs */
|
||||
|
||||
#define GPIO_LED1 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
|
||||
GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN0)
|
||||
#define GPIO_LED2 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
|
||||
GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN1)
|
||||
|
||||
/* BUTTONS -- NOTE that some have EXTI interrupts configured */
|
||||
|
||||
#define MIN_IRQBUTTON BUTTON_KEYA
|
||||
#define MAX_IRQBUTTON BUTTON_KEYB
|
||||
#define NUM_IRQBUTTONS NUM_BUTTONS
|
||||
|
||||
/* Button A is externally pulled up */
|
||||
#define GPIO_BTN_KEYA (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_MODE_INPUT|\
|
||||
GPIO_PORTC|GPIO_PIN13)
|
||||
|
||||
/* Button B is externally pulled dw */
|
||||
#define GPIO_BTN_KEYB (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_MODE_INPUT|\
|
||||
GPIO_PORTB|GPIO_PIN2)
|
||||
|
||||
/* SPI touch screen (ADS7843) chip select: PA.4 */
|
||||
|
||||
#define GPIO_TS_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
|
||||
GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
|
||||
|
||||
/* Touch screen (ADS7843) IRQ pin: PB.6 */
|
||||
#define GPIO_TS_IRQ (GPIO_INPUT|GPIO_CNF_INPULLUP|GPIO_MODE_INPUT|\
|
||||
GPIO_PORTB|GPIO_PIN6)
|
||||
|
||||
/* USB Soft Connect Pullup: PB.7 */
|
||||
#define GPIO_USB_PULLUP (GPIO_OUTPUT|GPIO_CNF_OUTOD|GPIO_MODE_50MHz|\
|
||||
GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN7)
|
||||
|
||||
/* SD card detect pin: PD.3 */
|
||||
#define GPIO_SD_CD (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_MODE_INPUT|\
|
||||
GPIO_PORTD|GPIO_PIN3)
|
||||
|
||||
/************************************************************************************
|
||||
* Public Types
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Public data
|
||||
************************************************************************************/
|
||||
|
||||
#ifndef __ASSEMBLY__
|
||||
|
||||
/************************************************************************************
|
||||
* Public Functions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_spiinitialize
|
||||
*
|
||||
* Description:
|
||||
* Called to configure SPI chip select GPIO pins for the Hy-Mini STM32v board.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
extern void weak_function stm32_spiinitialize(void);
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_usbinitialize
|
||||
*
|
||||
* Description:
|
||||
* Called to setup USB-related GPIO pins for the Hy-Mini STM32v board.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
extern void weak_function stm32_usbinitialize(void);
|
||||
|
||||
#if defined(CONFIG_INPUT_ADS7843E)
|
||||
|
||||
/************************************************************************************
|
||||
* Name: Touchscreen initialization
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
extern int arch_tcinitialize(int minor);
|
||||
|
||||
extern void arch_tcuninitialize(void);
|
||||
|
||||
#endif /* CONFIG_INPUT_ADS7843E */
|
||||
|
||||
#endif /* __ASSEMBLY__ */
|
||||
#endif /* __CONFIGS_HYMINI_STM32V_INTERNAL_H */
|
||||
|
|
@ -0,0 +1,989 @@
|
|||
/************************************************************************************
|
||||
* configs/hymini-stm32v/src/ssd1289.c
|
||||
* arch/arm/src/board/ssd1289.c
|
||||
*
|
||||
* Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
* Laurent Latil <laurent@latil.nom.fr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <sys/types.h>
|
||||
#include <stdint.h>
|
||||
#include <stdbool.h>
|
||||
#include <string.h>
|
||||
#include <errno.h>
|
||||
#include <debug.h>
|
||||
|
||||
#include <nuttx/arch.h>
|
||||
#include <nuttx/spi.h>
|
||||
|
||||
#include <arch/board/board.h>
|
||||
|
||||
#include "up_arch.h"
|
||||
#include "stm32.h"
|
||||
#include "stm32_internal.h"
|
||||
#include "hymini_stm32v-internal.h"
|
||||
|
||||
#include "ssd1289.h"
|
||||
|
||||
/* Color depth and format */
|
||||
#define LCD_BPP 16
|
||||
#define LCD_COLORFMT FB_FMT_RGB16_565
|
||||
|
||||
/* Display Resolution */
|
||||
#if defined(CONFIG_LCD_LANDSCAPE)
|
||||
# define LCD_XRES 320
|
||||
# define LCD_YRES 240
|
||||
#else
|
||||
# define LCD_XRES 240
|
||||
# define LCD_YRES 320
|
||||
#endif
|
||||
|
||||
#define LCD_BL_TIMER_PERIOD 8999
|
||||
|
||||
|
||||
/* Debug ******************************************************************************/
|
||||
#ifdef CONFIG_DEBUG_LCD
|
||||
# define lcddbg(format, arg...) vdbg(format, ##arg)
|
||||
#else
|
||||
# define lcddbg(x...)
|
||||
#endif
|
||||
|
||||
/* LCD is connected to the FSMC_Bank1_NOR/SRAM1 and NE1 is used as ship select signal */
|
||||
/* RS <==> A16 */
|
||||
#define LCD_REG (*((volatile unsigned short *) 0x60000000)) /* RS = 0 */
|
||||
#define LCD_RAM (*((volatile unsigned short *) 0x60020000)) /* RS = 1 */
|
||||
|
||||
const uint16_t fsmc_gpios[] =
|
||||
{ /* A16... A24 */
|
||||
GPIO_NPS_A16, GPIO_NPS_A17, GPIO_NPS_A18, GPIO_NPS_A19, GPIO_NPS_A20,
|
||||
GPIO_NPS_A21, GPIO_NPS_A22, GPIO_NPS_A23,
|
||||
|
||||
/* D0... D15 */GPIO_NPS_D0, GPIO_NPS_D1, GPIO_NPS_D2, GPIO_NPS_D3,
|
||||
GPIO_NPS_D4, GPIO_NPS_D5, GPIO_NPS_D6, GPIO_NPS_D7, GPIO_NPS_D8, GPIO_NPS_D9,
|
||||
GPIO_NPS_D10, GPIO_NPS_D11, GPIO_NPS_D12, GPIO_NPS_D13, GPIO_NPS_D14,
|
||||
GPIO_NPS_D15,
|
||||
|
||||
/* NOE, NWE */GPIO_NPS_NOE, GPIO_NPS_NWE,
|
||||
|
||||
/* NE1 */GPIO_NPS_NE1 };
|
||||
|
||||
#define NGPIOS (sizeof(fsmc_gpios)/sizeof(uint16_t))
|
||||
|
||||
/** This should be put elsewhere */
|
||||
#ifdef __CC_ARM /* ARM Compiler */
|
||||
#define lcd_inline static __inline
|
||||
#elif defined (__ICCARM__) /* for IAR Compiler */
|
||||
#define lcd_inline inline
|
||||
#elif defined (__GNUC__) /* GNU GCC Compiler */
|
||||
#define lcd_inline static __inline
|
||||
#else
|
||||
#define lcd_inline static
|
||||
#endif
|
||||
|
||||
/* Low Level methods */
|
||||
void lcd_clear(uint16_t color);
|
||||
|
||||
/* LCD Data Transfer Methods */
|
||||
int lcd_putrun(fb_coord_t row, fb_coord_t col, FAR const uint8_t *buffer,
|
||||
size_t npixels);
|
||||
int lcd_getrun(fb_coord_t row, fb_coord_t col, FAR uint8_t *buffer,
|
||||
size_t npixels);
|
||||
|
||||
/* LCD Configuration */
|
||||
static int lcd_getvideoinfo(FAR struct lcd_dev_s *dev,
|
||||
FAR struct fb_videoinfo_s *vinfo);
|
||||
static int lcd_getplaneinfo(FAR struct lcd_dev_s *dev, unsigned int planeno,
|
||||
FAR struct lcd_planeinfo_s *pinfo);
|
||||
|
||||
/* LCD RGB Mapping */
|
||||
#ifdef CONFIG_FB_CMAP
|
||||
# error "RGB color mapping not supported by this driver"
|
||||
#endif
|
||||
|
||||
/* Cursor Controls */
|
||||
#ifdef CONFIG_FB_HWCURSOR
|
||||
# error "Cursor control not supported by this driver"
|
||||
#endif
|
||||
|
||||
/* LCD Specific Controls */
|
||||
static int lcd_getpower(struct lcd_dev_s *dev);
|
||||
static int lcd_setpower(struct lcd_dev_s *dev, int power);
|
||||
static int lcd_getcontrast(struct lcd_dev_s *dev);
|
||||
static int lcd_setcontrast(struct lcd_dev_s *dev, unsigned int contrast);
|
||||
|
||||
/* Initialization (LCD ctrl / backlight) */
|
||||
static inline void lcd_initialize(void);
|
||||
|
||||
#ifdef CONFIG_LCD_BACKLIGHT
|
||||
static void lcd_backlight(void);
|
||||
#else
|
||||
# define lcd_backlight()
|
||||
#endif
|
||||
|
||||
/**************************************************************************************
|
||||
* Private Data
|
||||
**************************************************************************************/
|
||||
|
||||
/* This is working memory allocated by the LCD driver for each LCD device
|
||||
* and for each color plane. This memory will hold one raster line of data.
|
||||
* The size of the allocated run buffer must therefore be at least
|
||||
* (bpp * xres / 8). Actual alignment of the buffer must conform to the
|
||||
* bitwidth of the underlying pixel type.
|
||||
*
|
||||
* If there are multiple planes, they may share the same working buffer
|
||||
* because different planes will not be operate on concurrently. However,
|
||||
* if there are multiple LCD devices, they must each have unique run buffers.
|
||||
*/
|
||||
|
||||
static uint16_t g_runbuffer[LCD_XRES];
|
||||
|
||||
/* This structure describes the overall LCD video controller */
|
||||
|
||||
static const struct fb_videoinfo_s g_videoinfo =
|
||||
{ .fmt = LCD_COLORFMT, /* Color format: RGB16-565: RRRR RGGG GGGB BBBB */
|
||||
.xres = LCD_XRES, /* Horizontal resolution in pixel columns */
|
||||
.yres = LCD_YRES, /* Vertical resolution in pixel rows */
|
||||
.nplanes = 1, /* Number of color planes supported */
|
||||
};
|
||||
|
||||
/* This is the standard, NuttX Plane information object */
|
||||
|
||||
static const struct lcd_planeinfo_s g_planeinfo =
|
||||
{ .putrun = lcd_putrun, /* Put a run into LCD memory */
|
||||
.getrun = lcd_getrun, /* Get a run from LCD memory */
|
||||
.buffer = (uint8_t*) g_runbuffer, /* Run scratch buffer */
|
||||
.bpp = LCD_BPP, /* Bits-per-pixel */
|
||||
};
|
||||
|
||||
/* This is the standard, NuttX LCD driver object */
|
||||
|
||||
static struct ssd1289_dev_s g_lcddev =
|
||||
{ .dev =
|
||||
{
|
||||
/* LCD Configuration */
|
||||
|
||||
.getvideoinfo = lcd_getvideoinfo,
|
||||
.getplaneinfo = lcd_getplaneinfo,
|
||||
|
||||
/* LCD RGB Mapping -- Not supported */
|
||||
/* Cursor Controls -- Not supported */
|
||||
|
||||
/* LCD Specific Controls */
|
||||
.getpower = lcd_getpower,
|
||||
.setpower = lcd_setpower,
|
||||
.getcontrast = lcd_getcontrast,
|
||||
.setcontrast = lcd_setcontrast,
|
||||
},
|
||||
.power=0
|
||||
};
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_extmemgpios
|
||||
*
|
||||
* Description:
|
||||
* Initialize GPIOs for NOR or SRAM
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
static inline void stm32_extmemgpios(const uint16_t *gpios, int ngpios)
|
||||
{
|
||||
int i;
|
||||
|
||||
/* Configure GPIOs */
|
||||
for (i = 0; i < ngpios; i++)
|
||||
{
|
||||
stm32_configgpio(gpios[i]);
|
||||
}
|
||||
}
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_enablefsmc
|
||||
*
|
||||
* Description:
|
||||
* enable clocking to the FSMC module
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
#ifndef CONFIG_STM32_FSMC
|
||||
# error CONFIG_STM32_FSMC is required for LCD support
|
||||
#endif
|
||||
|
||||
static void stm32_enablefsmc(void)
|
||||
{
|
||||
uint32_t regval;
|
||||
|
||||
/* Enable AHB clocking to the FSMC */
|
||||
|
||||
regval = getreg32( STM32_RCC_AHBENR);
|
||||
regval |= RCC_AHBENR_FSMCEN;
|
||||
putreg32(regval, STM32_RCC_AHBENR);
|
||||
}
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_disablefsmc
|
||||
*
|
||||
* Description:
|
||||
* enable clocking to the FSMC module
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
static void stm32_disablefsmc(void)
|
||||
{
|
||||
uint32_t regval;
|
||||
|
||||
/* Enable AHB clocking to the FSMC */
|
||||
|
||||
regval = getreg32( STM32_RCC_AHBENR);
|
||||
regval &= ~RCC_AHBENR_FSMCEN;
|
||||
putreg32(regval, STM32_RCC_AHBENR);
|
||||
}
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_selectlcd
|
||||
*
|
||||
* Description:
|
||||
* Initialize to the LCD
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
static void stm32_selectlcd(void)
|
||||
{
|
||||
/* Configure new GPIO state */
|
||||
stm32_extmemgpios(fsmc_gpios, NGPIOS);
|
||||
|
||||
/* Enable AHB clocking to the FSMC */
|
||||
stm32_enablefsmc();
|
||||
|
||||
/* Bank1 NOR/SRAM control register configuration */
|
||||
putreg32(FSMC_BCR_SRAM | FSMC_BCR_MWID16 | FSMC_BCR_WREN, STM32_FSMC_BCR1);
|
||||
|
||||
/* Bank1 NOR/SRAM timing register configuration */
|
||||
putreg32(
|
||||
FSMC_BTR_ADDSET(2)|FSMC_BTR_ADDHLD(0)|FSMC_BTR_DATAST(2)|FSMC_BTR_BUSTRUN(0)| FSMC_BTR_CLKDIV(0)|FSMC_BTR_DATLAT(0)|FSMC_BTR_ACCMODA,
|
||||
STM32_FSMC_BTR1);
|
||||
|
||||
/* As ext mode is not active the write timing is ignored!! */
|
||||
putreg32(0xffffffff, STM32_FSMC_BWTR1);
|
||||
|
||||
/* Enable the bank by setting the MBKEN bit */
|
||||
putreg32(FSMC_BCR_MBKEN | FSMC_BCR_SRAM | FSMC_BCR_MWID16 | FSMC_BCR_WREN,
|
||||
STM32_FSMC_BCR1);
|
||||
}
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_deselectlcd
|
||||
*
|
||||
* Description:
|
||||
* Disable the LCD
|
||||
*
|
||||
************************************************************************************/
|
||||
// FIXME: Check this code !!
|
||||
void stm32_deselectlcd(void)
|
||||
{
|
||||
/* Restore registers to their power up settings */
|
||||
|
||||
putreg32(0xffffffff, STM32_FSMC_BCR4);
|
||||
|
||||
/* Bank1 NOR/SRAM timing register configuration */
|
||||
|
||||
putreg32(0x0fffffff, STM32_FSMC_BTR4);
|
||||
|
||||
/* Disable AHB clocking to the FSMC */
|
||||
|
||||
stm32_disablefsmc();
|
||||
}
|
||||
|
||||
lcd_inline void write_cmd(unsigned short cmd)
|
||||
{
|
||||
LCD_REG = cmd;
|
||||
}
|
||||
|
||||
lcd_inline unsigned short read_data(void)
|
||||
{
|
||||
return LCD_RAM;
|
||||
}
|
||||
|
||||
lcd_inline void write_data(unsigned short data_code)
|
||||
{
|
||||
LCD_RAM = data_code;
|
||||
}
|
||||
|
||||
void write_reg(unsigned char reg_addr, unsigned short reg_val)
|
||||
{
|
||||
write_cmd(reg_addr);
|
||||
write_data(reg_val);
|
||||
}
|
||||
|
||||
unsigned short read_reg(unsigned char reg_addr)
|
||||
{
|
||||
unsigned short val;
|
||||
write_cmd(reg_addr);
|
||||
val = read_data();
|
||||
return (val);
|
||||
}
|
||||
|
||||
static inline void lcd_gramselect(void)
|
||||
{
|
||||
write_cmd(0x22);
|
||||
}
|
||||
|
||||
void lcd_setcursor(unsigned int x, unsigned int y)
|
||||
{
|
||||
#if defined(CONFIG_LCD_PORTRAIT) || defined (CONFIG_LCD_RPORTRAIT)
|
||||
# if defined (CONFIG_LCD_RPORTRAIT)
|
||||
x = (LCD_XRES - 1) - x;
|
||||
y = (LCD_YRES - 1) - y;
|
||||
# endif
|
||||
write_reg(0x4e, x);
|
||||
write_reg(0x4f, y);
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_LCD_LANDSCAPE)
|
||||
y = (LCD_YRES - 1) - y;
|
||||
|
||||
write_reg(0x4e, y);
|
||||
write_reg(0x4f, x);
|
||||
#endif
|
||||
}
|
||||
|
||||
/**************************************************************************************
|
||||
* Name: lcd_putrun
|
||||
*
|
||||
* Description:
|
||||
* This method can be used to write a partial raster line to the LCD:
|
||||
*
|
||||
* row - Starting row to write to (range: 0 <= row < yres)
|
||||
* col - Starting column to write to (range: 0 <= col <= xres-npixels)
|
||||
* buffer - The buffer containing the run to be written to the LCD
|
||||
* npixels - The number of pixels to write to the LCD
|
||||
* (range: 0 < npixels <= xres-col)
|
||||
*
|
||||
**************************************************************************************/
|
||||
|
||||
int lcd_putrun(fb_coord_t row, fb_coord_t col, FAR const uint8_t *buffer,
|
||||
size_t npixels)
|
||||
{
|
||||
int i;
|
||||
FAR const uint16_t *src = (FAR const uint16_t*) buffer;
|
||||
|
||||
/* Buffer must be provided and aligned to a 16-bit address boundary */
|
||||
DEBUGASSERT(buffer && ((uintptr_t)buffer & 1) == 0);
|
||||
|
||||
/* Write the run to GRAM. */
|
||||
lcd_setcursor(col, row);
|
||||
|
||||
lcd_gramselect();
|
||||
for (i = 0; i < npixels; i++)
|
||||
{
|
||||
write_data(*src++);
|
||||
}
|
||||
return OK;
|
||||
}
|
||||
|
||||
/**************************************************************************************
|
||||
* Name: lcd_getrun
|
||||
*
|
||||
* Description:
|
||||
* This method can be used to read a partial raster line from the LCD:
|
||||
*
|
||||
* row - Starting row to read from (range: 0 <= row < yres)
|
||||
* col - Starting column to read read (range: 0 <= col <= xres-npixels)
|
||||
* buffer - The buffer in which to return the run read from the LCD
|
||||
* npixels - The number of pixels to read from the LCD
|
||||
* (range: 0 < npixels <= xres-col)
|
||||
*
|
||||
**************************************************************************************/
|
||||
|
||||
int lcd_getrun(fb_coord_t row, fb_coord_t col, FAR uint8_t *buffer,
|
||||
size_t npixels)
|
||||
{
|
||||
FAR uint16_t *dest = (FAR uint16_t*) buffer;
|
||||
int i;
|
||||
|
||||
/* Buffer must be provided and aligned to a 16-bit address boundary */
|
||||
DEBUGASSERT(buffer && ((uintptr_t)buffer & 1) == 0);
|
||||
|
||||
/* Read the run from GRAM. */
|
||||
lcd_setcursor(col, row);
|
||||
|
||||
lcd_gramselect();
|
||||
|
||||
/* dummy read */
|
||||
(void)read_data();
|
||||
|
||||
for (i = 0; i < npixels; i++)
|
||||
{
|
||||
*dest++ = read_data();
|
||||
}
|
||||
return OK;
|
||||
}
|
||||
|
||||
/**************************************************************************************
|
||||
* Name: lcd_getvideoinfo
|
||||
*
|
||||
* Description:
|
||||
* Get information about the LCD video controller configuration.
|
||||
*
|
||||
**************************************************************************************/
|
||||
|
||||
static int lcd_getvideoinfo(FAR struct lcd_dev_s *dev,
|
||||
FAR struct fb_videoinfo_s *vinfo)
|
||||
{
|
||||
DEBUGASSERT(dev && vinfo);gvdbg("fmt: %d xres: %d yres: %d nplanes: %d\n",
|
||||
g_videoinfo.fmt, g_videoinfo.xres, g_videoinfo.yres, g_videoinfo.nplanes);
|
||||
memcpy(vinfo, &g_videoinfo, sizeof(struct fb_videoinfo_s));
|
||||
return OK;
|
||||
}
|
||||
|
||||
/**************************************************************************************
|
||||
* Name: lcd_getplaneinfo
|
||||
*
|
||||
* Description:
|
||||
* Get information about the configuration of each LCD color plane.
|
||||
*
|
||||
**************************************************************************************/
|
||||
|
||||
static int lcd_getplaneinfo(FAR struct lcd_dev_s *dev, unsigned int planeno,
|
||||
FAR struct lcd_planeinfo_s *pinfo)
|
||||
{
|
||||
DEBUGASSERT(dev && pinfo && planeno == 0);gvdbg("planeno: %d bpp: %d\n", planeno, g_planeinfo.bpp);
|
||||
memcpy(pinfo, &g_planeinfo, sizeof(struct lcd_planeinfo_s));
|
||||
return OK;
|
||||
}
|
||||
|
||||
/**************************************************************************************
|
||||
* Name: lcd_getpower
|
||||
*
|
||||
* Description:
|
||||
* Get the LCD panel power status (0: full off - CONFIG_LCD_MAXPOWER: full on). On
|
||||
* backlit LCDs, this setting may correspond to the backlight setting.
|
||||
*
|
||||
**************************************************************************************/
|
||||
|
||||
static int lcd_getpower(struct lcd_dev_s *dev)
|
||||
{
|
||||
gvdbg("power: %d\n", 0);
|
||||
return g_lcddev.power;
|
||||
}
|
||||
|
||||
/**************************************************************************************
|
||||
* Name: lcd_setpower
|
||||
*
|
||||
* Description:
|
||||
* Enable/disable LCD panel power (0: full off - CONFIG_LCD_MAXPOWER: full on).
|
||||
* Used here to set pwm duty on timer used for backlight.
|
||||
*
|
||||
**************************************************************************************/
|
||||
|
||||
static int lcd_setpower(struct lcd_dev_s *dev, int power)
|
||||
{
|
||||
if (g_lcddev.power == power) {
|
||||
return OK;
|
||||
}
|
||||
|
||||
gvdbg("power: %d\n", power);
|
||||
DEBUGASSERT(power <= CONFIG_LCD_MAXPOWER);
|
||||
|
||||
/* Set new power level */
|
||||
|
||||
if (power > 0)
|
||||
{
|
||||
#ifdef CONFIG_LCD_BACKLIGHT
|
||||
uint32_t duty;
|
||||
|
||||
/* Calculate the new backlight duty. It is a fraction of the timer
|
||||
* period based on the ration of the current power setting to the
|
||||
* maximum power setting.
|
||||
*/
|
||||
duty = ((uint32_t)LCD_BL_TIMER_PERIOD * (uint32_t)power) / CONFIG_LCD_MAXPOWER;
|
||||
if (duty >= LCD_BL_TIMER_PERIOD)
|
||||
{
|
||||
duty = LCD_BL_TIMER_PERIOD - 1;
|
||||
}
|
||||
gvdbg("PWM duty: %d\n", duty);
|
||||
putreg16((uint16_t)duty, STM32_TIM3_CCR2);
|
||||
#endif
|
||||
/* TODO turn the display on */
|
||||
}
|
||||
else
|
||||
{
|
||||
/* FIXME: Turn display off ? */
|
||||
gvdbg("Force PWM to 0\n");
|
||||
putreg16((uint16_t)0, STM32_TIM3_CCR2);
|
||||
}
|
||||
g_lcddev.power = power;
|
||||
return OK;
|
||||
}
|
||||
|
||||
|
||||
/**************************************************************************************
|
||||
* Name: lcd_getcontrast
|
||||
*
|
||||
* Description:
|
||||
* Get the current contrast setting (0-CONFIG_LCD_MAXCONTRAST).
|
||||
*
|
||||
**************************************************************************************/
|
||||
|
||||
static int lcd_getcontrast(struct lcd_dev_s *dev)
|
||||
{
|
||||
gvdbg("Not implemented\n");
|
||||
return -ENOSYS;
|
||||
}
|
||||
|
||||
/**************************************************************************************
|
||||
* Name: lcd_setcontrast
|
||||
*
|
||||
* Description:
|
||||
* Set LCD panel contrast (0-CONFIG_LCD_MAXCONTRAST).
|
||||
*
|
||||
**************************************************************************************/
|
||||
|
||||
static int lcd_setcontrast(struct lcd_dev_s *dev, unsigned int contrast)
|
||||
{
|
||||
gvdbg("Not implemented\n");
|
||||
return -ENOSYS;
|
||||
}
|
||||
|
||||
/**************************************************************************************
|
||||
* Name: lcd_lcdinitialize
|
||||
*
|
||||
* Description:
|
||||
* Set LCD panel contrast (0-CONFIG_LCD_MAXCONTRAST).
|
||||
*
|
||||
**************************************************************************************/
|
||||
static inline void lcd_initialize(void)
|
||||
{
|
||||
/* Display control (GON=1,DTE=0,D[1:0]=01)
|
||||
D[1:0]=01 - Internal display is performed, display is off.
|
||||
*/
|
||||
write_reg(0x07, 0x0021);
|
||||
|
||||
/* Oscillator (OSCEN=1) */
|
||||
write_reg(0x00, 0x0001);
|
||||
|
||||
/* Display control (GON=1,DTE=0,D[1:0]=11)
|
||||
D[1:0]=11 - Internal display is performed, display is on.
|
||||
*/
|
||||
write_reg(0x07, 0x0023);
|
||||
|
||||
/* Wait 30ms */
|
||||
up_mdelay(30);
|
||||
|
||||
/* Display control (GON=1,DTE=1,D[1:0]=11) */
|
||||
write_reg(0x07, 0x0033);
|
||||
|
||||
/* Power control 1
|
||||
DCT3 DCT2 DCT1 DCT0 BT2 BT1 BT0 - DC3 DC2 DC1 DC0 AP2 AP1 AP0 -
|
||||
1 0 1 0 1 0 0 0 1 0 1 0 0 1 0 0
|
||||
DCT[3:0] - 1010: fosc/4 (step-up cycle of the step-up circuit for 8-color mode)
|
||||
BT[2:0] - 100 (step-up factor of the step-up circuit)
|
||||
DC[3:0] - 1010: fosc/4 (step-up cycle of the step-up circuit for 262k-color mode)
|
||||
AP[2:0] - 010: Small to medium (amount of current from the stable-current source in internal operational amplifier circuit)
|
||||
*/
|
||||
write_reg(0x03, 0xA8A4); /* or 0x0804 ?? */
|
||||
|
||||
/* Power Control 2
|
||||
VRC[2:0] - 000: 5.1v (VCIX2 output voltage)
|
||||
*/
|
||||
write_reg(0x0C, 0x0000);
|
||||
|
||||
/* Power Control 3
|
||||
- - - - - - - - - - - - VRH3 VRH2 VRH1 VRH0
|
||||
0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
|
||||
VRH[3:0] - 1000: Vref x 2.165 (Set amplitude magnification of VLCD63)
|
||||
*/
|
||||
write_reg(0x0D, 0x0008); // or 0x080C ??
|
||||
|
||||
/* power control 4
|
||||
- - VCOMG VDV4 VDV3 VDV2 VDV1 VDV0 - - - - - - - -
|
||||
0 0 1 0 1 0 0 1 0 0 0 0 0 0 0 0
|
||||
VDV[4:0] - 01001: VLCD63 x 0.xx (Vcom amplitude)
|
||||
VCOMG - 1 (enable output voltage of VcomL - VDV[4:0])
|
||||
*/
|
||||
write_reg(0x0E, 0x2900);
|
||||
|
||||
/* Power Control 5
|
||||
- - - - - - - - nOTP - VCM5 VCM4 VCM3 VCM2 VCM1 VCM0
|
||||
0 0 0 0 0 0 0 0 1 0 1 1 1 0 0 0
|
||||
nOTP: 1 - setting of VCM[5:0] becomes valid and voltage of VcomH can be adjusted.
|
||||
VCM[5-0] - 111000: VLCD63 x 0.xx (amplify the VcomH voltage 0.35 to 0.99 times the VLCD63 voltage)
|
||||
*/
|
||||
write_reg(0x1E, 0x00B8);
|
||||
|
||||
/* Driver Output Control
|
||||
- RL REV CAD BGR SM TB MUX8 MUX7 MUX6 MUX5 MUX4 MUX3 MUX2 MUX1 MUX0
|
||||
0 0 1 0 1 0 1 1 0 0 1 1 1 1 1 1
|
||||
RL - 0 RL setting is ignored when display with RAM (Dmode[1:0] = 00).
|
||||
REV - 1 Reverse source output level
|
||||
CAD - 0 Cs on Common
|
||||
BGR - 1 BGR (Selects the order from RGB to BGR in writing 18-bit pixel data in the GDDRAM)
|
||||
SM - 0 (Gate scan sequence)
|
||||
TB - 1 (output shift direction of the gate driver)
|
||||
MUX[8:0] - 100111111 (319) (number of lines for the LCD driver)
|
||||
*/
|
||||
write_reg(0x01, 0x2B3F);
|
||||
|
||||
/* LCD-Driving-Waveform Control
|
||||
- - - FLD ENWS B/C EOR WSMD NW7 NW6 NW5 NW4 NW3 NW2 NW1 NW0
|
||||
0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 0
|
||||
FLD - 0 ?
|
||||
ENWS- 0 (disable WSYNC output pin -> HiZ)
|
||||
B/C - 1 (When B/C = 1, a N-line inversion waveform is generated and alternates in a N-line equals to NW[7:0]+1)
|
||||
EOR - 1
|
||||
WSMD- 0
|
||||
NW[7:0] - 0 Specify the number of lines that will alternate at the N-line inversion setting (if B/C = 1).
|
||||
*/
|
||||
/* Set FLD ? */
|
||||
write_reg(0x02, 0x0600);
|
||||
|
||||
/* Exit sleep mode */
|
||||
write_reg(0x10, 0x0000);
|
||||
|
||||
/* Entry Mode
|
||||
VSMode DFM1 DFM0 TRANS OEDef WMode DMode1 DMode0 TY1 TY0 ID1 ID0 AM LG2 LG1 LG0
|
||||
0 1 1 0 0 0 0 0 0 1 1 1 0 0 0 0
|
||||
VSMode - 0 When VSMode = 1 at DMode[1:0] = “00”, the frame frequency will be dependent on VSYNC.
|
||||
DFM[1:0] - 11 (65k color mode selected)
|
||||
TRANS - 0 (if TRANS = 1, transparent display is allowed during DMode[1:0] = “1x”)
|
||||
0EDef - 0 (display window is defined by R4Eh and R4Fh)
|
||||
WMode - 0 (Normal data bus)
|
||||
DMode[1:0] - 00 (data display from RAM data)
|
||||
TY[1:0] - 01 (type B. Used for 262k color mode only)
|
||||
ID[1:0] - 11 (address counter auto incremented by 1, horizontal & vertical)
|
||||
AM - 0 Horizontal (direction of the address counter update after data are written to the GDDRAM)
|
||||
LG[2:0] - 000 (operation to perform according to GDRAM compare registers ?)
|
||||
*/
|
||||
#if defined(CONFIG_LCD_PORTRAIT)
|
||||
write_reg(0x11, 0x6070);
|
||||
#elif defined(CONFIG_LCD_RPORTRAIT)
|
||||
/* ID[1:0] - 00 (address counter auto decremented by 1, horizontal & vertical) */
|
||||
write_reg(0x11, 0x6840);
|
||||
#elif defined(CONFIG_LCD_LANDSCAPE)
|
||||
/* ID[1:0] - 10 (address counter auto decremented by 1, horizontal & vertical)
|
||||
AM - 1 Vertical direction
|
||||
*/
|
||||
write_reg(0x11, 0x6068);
|
||||
#else
|
||||
#error "LCD orientation not supported"
|
||||
#endif
|
||||
|
||||
/* Compare register (unused ?) */
|
||||
write_reg(0x05, 0x0000);
|
||||
write_reg(0x06, 0x0000);
|
||||
|
||||
/* Horizontal Porch
|
||||
XL7 XL6 XL5 XL4 XL3 XL2 IB9 XL1 HBP7 HBP6 HBP5 HBP4 HBP3 HBP2 HBP1 HBP0
|
||||
XL[7:0] - 0xEF (239) (Number of valid pixel per line is equal to XL[7:0] + 1)
|
||||
HBP[7:0] - 0x1C (28) 30 dot clocks (delay period from falling edge of HSYNC signal to first valid data)
|
||||
*/
|
||||
write_reg(0x16, 0xEF1C);
|
||||
|
||||
/* Vertical Porch */
|
||||
write_reg(0x17, 0x0003);
|
||||
|
||||
/* Display control
|
||||
- - - PT1 PT0 VLE2 VLE1 SPT - - GON DTE CM - D1 D0
|
||||
0 0 0 0 0 0 0 1 0 0 1 1 0 0 1 1
|
||||
VLE[2:1]: 00 (When VLE1 = 1 or VLE2 = 1, vertical scroll performed in the 1st screen by taking data VL17-0 in R41h
|
||||
register. When VLE1 = 1 and VLE2 = 1, a vertical scroll is performed in the 1st and 2nd screen by VL1[8:0] and VL2[8:0])
|
||||
SPT: 1 (When SPT = “1”, the 2-division LCD drive is performed.
|
||||
CM: 0 (8-color mode setting 0=disabled, 1=enabled)
|
||||
D[1:0]: 11
|
||||
*/
|
||||
write_reg(0x07, 0x0133);
|
||||
|
||||
/* Frame Cycle Control */
|
||||
write_reg(0x0B, 0x0000);
|
||||
|
||||
/* Gate Scan Position */
|
||||
/* write_reg(0x0F, 0x0000); // Default value */
|
||||
|
||||
/* Vertical Scroll Control */
|
||||
write_reg(0x41, 0x0000);
|
||||
write_reg(0x42, 0x0000);
|
||||
|
||||
/* 1st Screen driving position
|
||||
driving start position for the first screen in a line unit. (0)
|
||||
*/
|
||||
write_reg(0x48, 0x0000);
|
||||
/* driving end position for the first screen in a line unit. (319) */
|
||||
write_reg(0x49, 0x013F);
|
||||
|
||||
/* 2nd Screen driving position (unused) */
|
||||
write_reg(0x4A, 0x0000);
|
||||
write_reg(0x4B, 0x0000);
|
||||
|
||||
/* start/end positions of the window address in the horizontal direction */
|
||||
write_reg(0x44, 0xEF00);
|
||||
|
||||
/* start/end positions of the window address in the vertical direction */
|
||||
/* write_reg(0x45, 0x0000); // Default value
|
||||
write_reg(0x46, 0x013F); // Default value
|
||||
*/
|
||||
|
||||
/* Gamma Control */
|
||||
write_reg(0x0030, 0x0707);
|
||||
write_reg(0x0031, 0x0204);
|
||||
write_reg(0x0032, 0x0204);
|
||||
write_reg(0x0033, 0x0502);
|
||||
write_reg(0x0034, 0x0507);
|
||||
write_reg(0x0035, 0x0204);
|
||||
write_reg(0x0036, 0x0204);
|
||||
write_reg(0x0037, 0x0502);
|
||||
write_reg(0x003A, 0x0302);
|
||||
write_reg(0x003B, 0x0302);
|
||||
|
||||
/* RAM write data mask (unused)
|
||||
write_reg(0x23, 0x0000); // Default value
|
||||
write_reg(0x24, 0x0000); // Default value
|
||||
*/
|
||||
|
||||
/* Setting R28h as 0x0006 is required before setting R25h and R29h registers.*/
|
||||
|
||||
write_reg(0x28, 0x0006);
|
||||
|
||||
/* Frame Frequency Control (R25h)
|
||||
OSC3 OSC2 OSC1 OSC0 - - - - - - - - - - - -
|
||||
1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0
|
||||
OSC[3:0]: 1110 Corresponding frame freq: 80Hz
|
||||
*/
|
||||
write_reg(0x25, 0xE000); /* (Default value = 8000h) */
|
||||
}
|
||||
|
||||
/**************************************************************************************
|
||||
* Name: lcd_backlight
|
||||
*
|
||||
* Description:
|
||||
* The LCD backlight is driven from PB.5 which must be configured as TIM3
|
||||
* CH2. TIM3 must then be configured to pwm output on PB.5; the duty
|
||||
* of the clock determines the backlight level.
|
||||
*
|
||||
**************************************************************************************/
|
||||
|
||||
#ifdef CONFIG_LCD_BACKLIGHT
|
||||
|
||||
#ifndef CONFIG_STM32_TIM3_PARTIAL_REMAP
|
||||
# error CONFIG_STM32_TIM3_PARTIAL_REMAP must be set (to have TIM3 CH2 on pin B.5)
|
||||
#endif
|
||||
|
||||
static void lcd_backlight(void)
|
||||
{
|
||||
uint16_t ccmr;
|
||||
uint16_t ccer;
|
||||
uint16_t cr2;
|
||||
|
||||
/* Configure PB5 as TIM3 CH2 output */
|
||||
stm32_configgpio(GPIO_TIM3_CH2OUT);
|
||||
|
||||
/* Enabled timer 3 clocking */
|
||||
modifyreg32(STM32_RCC_APB1ENR, 0, RCC_APB1ENR_TIM3EN);
|
||||
|
||||
/* Reset timer 3 */
|
||||
|
||||
modifyreg32(STM32_RCC_APB1RSTR, 0, RCC_APB1RSTR_TIM3RST);
|
||||
modifyreg32(STM32_RCC_APB1RSTR, RCC_APB1RSTR_TIM3RST, 0);
|
||||
|
||||
/* Reset the Counter Mode and set the clock division */
|
||||
putreg16(0, STM32_TIM3_CR1);
|
||||
|
||||
/* Set the Autoreload value */
|
||||
putreg16(LCD_BL_TIMER_PERIOD, STM32_TIM3_ARR);
|
||||
|
||||
/* Set the Prescaler value */
|
||||
|
||||
putreg16(0, STM32_TIM3_PSC);
|
||||
|
||||
/* Generate an update event to reload the Prescaler value immediatly */
|
||||
|
||||
putreg16(ATIM_EGR_UG, STM32_TIM3_EGR);
|
||||
|
||||
/* Disable the Channel 2 */
|
||||
|
||||
ccer = getreg16(STM32_TIM3_CCER);
|
||||
ccer &= ~ATIM_CCER_CC2E;
|
||||
putreg16(ccer, STM32_TIM3_CCER);
|
||||
|
||||
/* Get the TIM3 CR2 register value */
|
||||
cr2 = getreg16(STM32_TIM3_CR2);
|
||||
|
||||
/* Select the Output Compare Mode Bits */
|
||||
|
||||
ccmr = getreg16(STM32_TIM3_CCMR1);
|
||||
ccmr &= ATIM_CCMR1_OC2M_MASK;
|
||||
ccmr |= (ATIM_CCMR_MODE_PWM1 << ATIM_CCMR1_OC2M_SHIFT);
|
||||
|
||||
/* Set the capture compare register value (50% duty) */
|
||||
// FIXME should be set to 0 (appl needs to call setpower to change it)
|
||||
g_lcddev.power = (CONFIG_LCD_MAXPOWER + 1) / 2;
|
||||
putreg16((LCD_BL_TIMER_PERIOD + 1) / 2, STM32_TIM3_CCR2);
|
||||
|
||||
/* Select the output polarity level == HIGH */
|
||||
ccer &= !ATIM_CCER_CC2P;
|
||||
|
||||
/* Enable channel 2*/
|
||||
ccer |= ATIM_CCER_CC2E;
|
||||
|
||||
/* Write the timer configuration */
|
||||
|
||||
putreg16(ccmr, STM32_TIM3_CCMR1);
|
||||
putreg16(ccer, STM32_TIM3_CCER);
|
||||
|
||||
/* Set the auto preload enable bit */
|
||||
|
||||
modifyreg16(STM32_TIM3_CR1, 0, ATIM_CR1_ARPE);
|
||||
|
||||
/* Enable Backlight Timer !!!!*/
|
||||
modifyreg16(STM32_TIM3_CR1, 0, ATIM_CR1_CEN);
|
||||
|
||||
/* Dump timer3 registers */
|
||||
lcddbg("APB1ENR: %08x\n", getreg32(STM32_RCC_APB1ENR));
|
||||
lcddbg("CR1: %04x\n", getreg32(STM32_TIM3_CR1));
|
||||
lcddbg("CR2: %04x\n", getreg32(STM32_TIM3_CR2));
|
||||
lcddbg("SMCR: %04x\n", getreg32(STM32_TIM3_SMCR));
|
||||
lcddbg("DIER: %04x\n", getreg32(STM32_TIM3_DIER));
|
||||
lcddbg("SR: %04x\n", getreg32(STM32_TIM3_SR));
|
||||
lcddbg("EGR: %04x\n", getreg32(STM32_TIM3_EGR));
|
||||
lcddbg("CCMR1: %04x\n", getreg32(STM32_TIM3_CCMR1));
|
||||
lcddbg("CCMR2: %04x\n", getreg32(STM32_TIM3_CCMR2));
|
||||
lcddbg("CCER: %04x\n", getreg32(STM32_TIM3_CCER));
|
||||
lcddbg("CNT: %04x\n", getreg32(STM32_TIM3_CNT));
|
||||
lcddbg("PSC: %04x\n", getreg32(STM32_TIM3_PSC));
|
||||
lcddbg("ARR: %04x\n", getreg32(STM32_TIM3_ARR));
|
||||
lcddbg("CCR1: %04x\n", getreg32(STM32_TIM3_CCR1));
|
||||
lcddbg("CCR2: %04x\n", getreg32(STM32_TIM3_CCR2));
|
||||
lcddbg("CCR3: %04x\n", getreg32(STM32_TIM3_CCR3));
|
||||
lcddbg("CCR4: %04x\n", getreg32(STM32_TIM3_CCR4));
|
||||
lcddbg("CCR4: %04x\n", getreg32(STM32_TIM3_CCR4));
|
||||
lcddbg("CCR4: %04x\n", getreg32(STM32_TIM3_CCR4));
|
||||
lcddbg("DMAR: %04x\n", getreg32(STM32_TIM3_DMAR));
|
||||
}
|
||||
#endif
|
||||
|
||||
/**************************************************************************************
|
||||
* Public Functions
|
||||
**************************************************************************************/
|
||||
|
||||
/**************************************************************************************
|
||||
* Name: up_lcdinitialize
|
||||
*
|
||||
* Description:
|
||||
* Initialize the LCD video hardware. The initial state of the LCD is fully
|
||||
* initialized, display memory cleared, and the LCD ready to use, but with the power
|
||||
* setting at 0 (full off).
|
||||
*
|
||||
**************************************************************************************/
|
||||
|
||||
int up_lcdinitialize(void)
|
||||
{
|
||||
unsigned short id;
|
||||
|
||||
gvdbg("Initializing\n");
|
||||
|
||||
/* Configure GPIO pins and configure the FSMC to support the LCD */
|
||||
stm32_selectlcd();
|
||||
|
||||
/* Delay required here */
|
||||
|
||||
up_mdelay(50);
|
||||
|
||||
/* Check model id */
|
||||
|
||||
id=read_reg(0x0);
|
||||
if (id != SSD1289_ID) {
|
||||
/* Not a SSD1289 ? */
|
||||
gdbg("up_lcdinitialize: LCD ctrl is not a SSD1289");
|
||||
return ERROR;
|
||||
}
|
||||
|
||||
/* Configure and enable LCD */
|
||||
|
||||
lcd_initialize();
|
||||
|
||||
/* Clear the display (setting it to the color 0=black) */
|
||||
|
||||
lcd_clear(0);
|
||||
|
||||
/* Configure the backlight */
|
||||
|
||||
lcd_backlight();
|
||||
return OK;
|
||||
}
|
||||
|
||||
/**************************************************************************************
|
||||
* Name: up_lcdgetdev
|
||||
*
|
||||
* Description:
|
||||
* Return a a reference to the LCD object for the specified LCD. This allows support
|
||||
* for multiple LCD devices.
|
||||
*
|
||||
**************************************************************************************/
|
||||
|
||||
FAR struct lcd_dev_s *up_lcdgetdev(int lcddev)
|
||||
{
|
||||
DEBUGASSERT(lcddev == 0);
|
||||
return &g_lcddev.dev;
|
||||
}
|
||||
|
||||
/**************************************************************************************
|
||||
* Name: up_lcduninitialize
|
||||
*
|
||||
* Description:
|
||||
* Un-initialize the LCD support
|
||||
*
|
||||
**************************************************************************************/
|
||||
|
||||
void up_lcduninitialize(void)
|
||||
{
|
||||
lcd_setpower(&g_lcddev.dev, 0);
|
||||
stm32_deselectlcd();
|
||||
}
|
||||
|
||||
/**************************************************************************************
|
||||
* Name: lcd_clear
|
||||
*
|
||||
* Description:
|
||||
* Fill the LCD ctrl memory with given color
|
||||
*
|
||||
**************************************************************************************/
|
||||
|
||||
void lcd_clear(uint16_t color)
|
||||
{
|
||||
uint32_t index;
|
||||
lcd_setcursor(0, 0);
|
||||
lcd_gramselect(); /* Prepare to write GRAM */
|
||||
for (index = 0; index < LCD_XRES * LCD_YRES; index++)
|
||||
{
|
||||
write_data(color);
|
||||
}
|
||||
}
|
|
@ -0,0 +1,55 @@
|
|||
/************************************************************************************
|
||||
* configs/hymini-stm32v/src/ssd1289.h
|
||||
* arch/arm/src/board/ssd1289.h
|
||||
*
|
||||
* Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
* Laurent Latil <laurent@latil.nom.fr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
#ifndef SSD1289_H_
|
||||
#define SSD1289_H_
|
||||
|
||||
#include <nuttx/lcd/lcd.h>
|
||||
|
||||
/* LCD IDs */
|
||||
#define SSD1289_ID 0x8989
|
||||
|
||||
struct ssd1289_dev_s
|
||||
{
|
||||
/* Publicly visible device structure */
|
||||
struct lcd_dev_s dev;
|
||||
|
||||
/* Private LCD-specific information follows */
|
||||
uint8_t power; /* Current power setting */
|
||||
};
|
||||
|
||||
#endif /* SSD1289_H_ */
|
|
@ -0,0 +1,103 @@
|
|||
/************************************************************************************
|
||||
* configs/hymini-stm32v/src/up_boot.c
|
||||
* arch/arm/src/board/up_boot.c
|
||||
*
|
||||
* Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
* Laurent Latil <laurent@latil.nom.fr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
#include <nuttx/spi.h>
|
||||
#include <debug.h>
|
||||
|
||||
#include <arch/board/board.h>
|
||||
|
||||
#include "up_arch.h"
|
||||
#include "hymini_stm32v-internal.h"
|
||||
|
||||
/************************************************************************************
|
||||
* Definitions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Private Data
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Public Functions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_boardinitialize
|
||||
*
|
||||
* Description:
|
||||
* All STM32 architectures must provide the following entry point. This entry point
|
||||
* is called early in the initialization -- after all memory has been configured
|
||||
* and mapped but before any devices have been initialized.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
void stm32_boardinitialize(void)
|
||||
{
|
||||
/* Configure SPI chip selects if 1) SPI is not disabled, and 2) the weak function
|
||||
* stm32_spiinitialize() has been brought into the link.
|
||||
*/
|
||||
|
||||
#if defined(CONFIG_STM32_SPI1) || defined(CONFIG_STM32_SPI2)
|
||||
if (stm32_spiinitialize)
|
||||
{
|
||||
stm32_spiinitialize();
|
||||
}
|
||||
#endif
|
||||
|
||||
/* Initialize USB is 1) USBDEV is selected, 2) the USB controller is not
|
||||
* disabled, and 3) the weak function stm32_usbinitialize() has been brought
|
||||
* into the build.
|
||||
*/
|
||||
|
||||
#if defined(CONFIG_USBDEV) && defined(CONFIG_STM32_USB)
|
||||
if (stm32_usbinitialize)
|
||||
{
|
||||
stm32_usbinitialize();
|
||||
}
|
||||
#endif
|
||||
|
||||
/* Configure on-board LEDs if LED support has been selected. */
|
||||
|
||||
#ifdef CONFIG_ARCH_LEDS
|
||||
up_ledinit();
|
||||
#endif
|
||||
}
|
|
@ -0,0 +1,159 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/src/up_buttons.c
|
||||
*
|
||||
* Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <stdint.h>
|
||||
|
||||
#include <arch/board/board.h>
|
||||
#include "hymini_stm32v-internal.h"
|
||||
|
||||
#ifdef CONFIG_ARCH_BUTTONS
|
||||
|
||||
/****************************************************************************
|
||||
* Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Private Data
|
||||
****************************************************************************/
|
||||
/* Pin configuration for each HY-mini button. This array is indexed by
|
||||
* the BUTTON_* definitions in board.h
|
||||
*/
|
||||
|
||||
//static const uint16_t g_buttons[NUM_BUTTONS] =
|
||||
// {
|
||||
// GPIO_BTN_KEYA, GPIO_BTN_KEYB
|
||||
// };
|
||||
|
||||
/****************************************************************************
|
||||
* Private Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Public Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Name: up_buttoninit
|
||||
*
|
||||
* Description:
|
||||
* up_buttoninit() must be called to initialize button resources. After
|
||||
* that, up_buttons() may be called to collect the current state of all
|
||||
* buttons or up_irqbutton() may be called to register button interrupt
|
||||
* handlers.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
void up_buttoninit(void)
|
||||
{
|
||||
stm32_configgpio(GPIO_BTN_KEYA);
|
||||
stm32_configgpio(GPIO_BTN_KEYB);
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: up_buttons
|
||||
****************************************************************************/
|
||||
|
||||
uint8_t up_buttons(void)
|
||||
{
|
||||
uint8_t ret = 0;
|
||||
bool pinValue;
|
||||
|
||||
/* Check that state of each key */
|
||||
|
||||
/* Pin is pulled up */
|
||||
pinValue = stm32_gpioread(GPIO_BTN_KEYA);
|
||||
if (!pinValue)
|
||||
{
|
||||
// Button pressed
|
||||
ret = 1 << BUTTON_KEYA;
|
||||
}
|
||||
|
||||
/* Pin is pulled down */
|
||||
pinValue = stm32_gpioread(GPIO_BTN_KEYB);
|
||||
if (pinValue)
|
||||
{
|
||||
// Button pressed
|
||||
ret |= 1 << BUTTON_KEYB;
|
||||
}
|
||||
return ret;
|
||||
}
|
||||
|
||||
/************************************************************************************
|
||||
* Button support.
|
||||
*
|
||||
* Description:
|
||||
* up_buttoninit() must be called to initialize button resources. After
|
||||
* that, up_buttons() may be called to collect the current state of all
|
||||
* buttons or up_irqbutton() may be called to register button interrupt
|
||||
* handlers.
|
||||
*
|
||||
* After up_buttoninit() has been called, up_buttons() may be called to
|
||||
* collect the state of all buttons. up_buttons() returns an 8-bit bit set
|
||||
* with each bit associated with a button. See the BUTTON_*_BIT and JOYSTICK_*_BIT
|
||||
* definitions in board.h for the meaning of each bit.
|
||||
*
|
||||
* up_irqbutton() may be called to register an interrupt handler that will
|
||||
* be called when a button is depressed or released. The ID value is a
|
||||
* button enumeration value that uniquely identifies a button resource. See the
|
||||
* BUTTON_* definitions in board.h for the meaning of enumeration
|
||||
* value. The previous interrupt handler address is returned (so that it may
|
||||
* restored, if so desired).
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
#ifdef CONFIG_ARCH_IRQBUTTONS
|
||||
xcpt_t up_irqbutton(int id, xcpt_t irqhandler)
|
||||
{
|
||||
xcpt_t oldhandler = NULL;
|
||||
uint32_t pinset = GPIO_BTN_KEYA;
|
||||
|
||||
if (id == 1)
|
||||
{
|
||||
pinset = GPIO_BTN_KEYB;
|
||||
}
|
||||
if (id < 2)
|
||||
{
|
||||
oldhandler = stm32_gpiosetevent(pinset, true, true, true, irqhandler);
|
||||
}
|
||||
return oldhandler;
|
||||
}
|
||||
#endif
|
||||
#endif /* CONFIG_ARCH_BUTTONS */
|
|
@ -0,0 +1,241 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/src/up_leds.c
|
||||
* arch/arm/src/board/up_leds.c
|
||||
*
|
||||
* Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
* Laurent Latil <laurent@latil.nom.fr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <stdint.h>
|
||||
#include <stdbool.h>
|
||||
#include <debug.h>
|
||||
|
||||
#include <arch/board/board.h>
|
||||
|
||||
#include "chip.h"
|
||||
#include "up_arch.h"
|
||||
#include "up_internal.h"
|
||||
#include "stm32_internal.h"
|
||||
#include "hymini_stm32v-internal.h"
|
||||
|
||||
/****************************************************************************
|
||||
* Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/* Enables debug output from this file (needs CONFIG_DEBUG with
|
||||
* CONFIG_DEBUG_VERBOSE too)
|
||||
*/
|
||||
|
||||
#undef LED_DEBUG /* Define to enable debug */
|
||||
|
||||
#ifdef LED_DEBUG
|
||||
# define leddbg lldbg
|
||||
# define ledvdbg llvdbg
|
||||
#else
|
||||
# define leddbg(x...)
|
||||
# define ledvdbg(x...)
|
||||
#endif
|
||||
|
||||
/* The following definitions map the encoded LED setting to GPIO settings */
|
||||
|
||||
#define HYMINI_STM32_LED1 (1 << 0)
|
||||
#define HYMINI_STM32_LED2 (1 << 1)
|
||||
|
||||
#define ON_SETBITS_SHIFT (0)
|
||||
#define ON_CLRBITS_SHIFT (4)
|
||||
#define OFF_SETBITS_SHIFT (8)
|
||||
#define OFF_CLRBITS_SHIFT (12)
|
||||
|
||||
#define ON_BITS(v) ((v) & 0xff)
|
||||
#define OFF_BITS(v) (((v) >> 8) & 0x0ff)
|
||||
#define SETBITS(b) ((b) & 0x0f)
|
||||
#define CLRBITS(b) (((b) >> 4) & 0x0f)
|
||||
|
||||
#define ON_SETBITS(v) (SETBITS(ON_BITS(v))
|
||||
#define ON_CLRBITS(v) (CLRBITS(ON_BITS(v))
|
||||
#define OFF_SETBITS(v) (SETBITS(OFF_BITS(v))
|
||||
#define OFF_CLRBITS(v) (CLRBITS(OFF_BITS(v))
|
||||
|
||||
/* On: !LED1 + !LED2 Off: - */
|
||||
#define LED_STARTED_ON_SETBITS ((0) << ON_SETBITS_SHIFT)
|
||||
#define LED_STARTED_ON_CLRBITS ((HYMINI_STM32_LED1|HYMINI_STM32_LED2) << ON_CLRBITS_SHIFT)
|
||||
#define LED_STARTED_OFF_SETBITS (0 << OFF_SETBITS_SHIFT)
|
||||
#define LED_STARTED_OFF_CLRBITS (0 << OFF_CLRBITS_SHIFT)
|
||||
|
||||
/* On: LED1+!LED2 Off: N/A */
|
||||
#define LED_HEAPALLOCATE_ON_SETBITS ((HYMINI_STM32_LED1) << ON_SETBITS_SHIFT)
|
||||
#define LED_HEAPALLOCATE_ON_CLRBITS ((HYMINI_STM32_LED2) << ON_CLRBITS_SHIFT)
|
||||
#define LED_HEAPALLOCATE_OFF_SETBITS (0)
|
||||
#define LED_HEAPALLOCATE_OFF_CLRBITS (0)
|
||||
|
||||
/* On: LED2+!LED1 Off: N/A */
|
||||
#define LED_IRQSENABLED_ON_SETBITS ((HYMINI_STM32_LED2) << ON_SETBITS_SHIFT)
|
||||
#define LED_IRQSENABLED_ON_CLRBITS ((HYMINI_STM32_LED1) << ON_CLRBITS_SHIFT)
|
||||
#define LED_IRQSENABLED_OFF_SETBITS (0)
|
||||
#define LED_IRQSENABLED_OFF_CLRBITS (0)
|
||||
|
||||
/* On: LED1+!LED2 Off: N/A */
|
||||
#define LED_STACKCREATED_ON_SETBITS ((HYMINI_STM32_LED1) << ON_SETBITS_SHIFT)
|
||||
#define LED_STACKCREATED_ON_CLRBITS ((HYMINI_STM32_LED2) << ON_CLRBITS_SHIFT)
|
||||
#define LED_STACKCREATED_OFF_SETBITS (0)
|
||||
#define LED_STACKCREATED_OFF_CLRBITS (0)
|
||||
|
||||
/* On: !LED1 Off: LED1 */
|
||||
#define LED_INIRQ_ON_SETBITS ((0) << ON_SETBITS_SHIFT)
|
||||
#define LED_INIRQ_ON_CLRBITS ((HYMINI_STM32_LED1) << ON_CLRBITS_SHIFT)
|
||||
#define LED_INIRQ_OFF_SETBITS ((HYMINI_STM32_LED1) << OFF_SETBITS_SHIFT)
|
||||
#define LED_INIRQ_OFF_CLRBITS ((0) << OFF_CLRBITS_SHIFT)
|
||||
|
||||
/* On: LED2 Off: !LED2 */
|
||||
#define LED_SIGNAL_ON_SETBITS ((HYMINI_STM32_LED2) << ON_SETBITS_SHIFT)
|
||||
#define LED_SIGNAL_ON_CLRBITS ((0) << ON_CLRBITS_SHIFT)
|
||||
#define LED_SIGNAL_OFF_SETBITS ((0) << OFF_SETBITS_SHIFT)
|
||||
#define LED_SIGNAL_OFF_CLRBITS ((HYMINI_STM32_LED2) << OFF_CLRBITS_SHIFT)
|
||||
|
||||
/* On: LED1+LED2 Off: - */
|
||||
#define LED_ASSERTION_ON_SETBITS ((HYMINI_STM32_LED2|HYMINI_STM32_LED2) << ON_SETBITS_SHIFT)
|
||||
#define LED_ASSERTION_ON_CLRBITS ((0) << ON_CLRBITS_SHIFT)
|
||||
#define LED_ASSERTION_OFF_SETBITS ((0) << OFF_SETBITS_SHIFT)
|
||||
#define LED_ASSERTION_OFF_CLRBITS ((0) << OFF_CLRBITS_SHIFT)
|
||||
|
||||
/* On: LED1 Off: LED2 */
|
||||
#define LED_PANIC_ON_SETBITS ((HYMINI_STM32_LED1) << ON_SETBITS_SHIFT)
|
||||
#define LED_PANIC_ON_CLRBITS ((HYMINI_STM32_LED2) << ON_CLRBITS_SHIFT)
|
||||
#define LED_PANIC_OFF_SETBITS ((HYMINI_STM32_LED2) << OFF_SETBITS_SHIFT)
|
||||
#define LED_PANIC_OFF_CLRBITS ((HYMINI_STM32_LED1) << OFF_CLRBITS_SHIFT)
|
||||
|
||||
/****************************************************************************
|
||||
* Private Data
|
||||
****************************************************************************/
|
||||
|
||||
static const uint16_t g_ledbits[8] =
|
||||
{ (LED_STARTED_ON_SETBITS | LED_STARTED_ON_CLRBITS | LED_STARTED_OFF_SETBITS
|
||||
| LED_STARTED_OFF_CLRBITS),
|
||||
|
||||
(LED_HEAPALLOCATE_ON_SETBITS | LED_HEAPALLOCATE_ON_CLRBITS
|
||||
| LED_HEAPALLOCATE_OFF_SETBITS | LED_HEAPALLOCATE_OFF_CLRBITS),
|
||||
|
||||
(LED_IRQSENABLED_ON_SETBITS | LED_IRQSENABLED_ON_CLRBITS
|
||||
| LED_IRQSENABLED_OFF_SETBITS | LED_IRQSENABLED_OFF_CLRBITS),
|
||||
|
||||
(LED_STACKCREATED_ON_SETBITS | LED_STACKCREATED_ON_CLRBITS
|
||||
| LED_STACKCREATED_OFF_SETBITS | LED_STACKCREATED_OFF_CLRBITS),
|
||||
|
||||
(LED_INIRQ_ON_SETBITS | LED_INIRQ_ON_CLRBITS | LED_INIRQ_OFF_SETBITS
|
||||
| LED_INIRQ_OFF_CLRBITS),
|
||||
|
||||
(LED_SIGNAL_ON_SETBITS | LED_SIGNAL_ON_CLRBITS | LED_SIGNAL_OFF_SETBITS
|
||||
| LED_SIGNAL_OFF_CLRBITS),
|
||||
|
||||
(LED_ASSERTION_ON_SETBITS | LED_ASSERTION_ON_CLRBITS | LED_ASSERTION_OFF_SETBITS
|
||||
| LED_ASSERTION_OFF_CLRBITS),
|
||||
|
||||
(LED_PANIC_ON_SETBITS | LED_PANIC_ON_CLRBITS | LED_PANIC_OFF_SETBITS
|
||||
| LED_PANIC_OFF_CLRBITS) };
|
||||
|
||||
/****************************************************************************
|
||||
* Private Functions
|
||||
****************************************************************************/
|
||||
|
||||
static inline void led_clrbits(unsigned int clrbits)
|
||||
{
|
||||
if ((clrbits & HYMINI_STM32_LED1) != 0)
|
||||
{
|
||||
stm32_gpiowrite(GPIO_LED1, false);
|
||||
}
|
||||
|
||||
if ((clrbits & HYMINI_STM32_LED2) != 0)
|
||||
{
|
||||
stm32_gpiowrite(GPIO_LED2, false);
|
||||
}
|
||||
}
|
||||
|
||||
static inline void led_setbits(unsigned int setbits)
|
||||
{
|
||||
if ((setbits & HYMINI_STM32_LED1) != 0)
|
||||
{
|
||||
stm32_gpiowrite(GPIO_LED1, true);
|
||||
}
|
||||
|
||||
if ((setbits & HYMINI_STM32_LED2) != 0)
|
||||
{
|
||||
stm32_gpiowrite(GPIO_LED2, true);
|
||||
}
|
||||
}
|
||||
|
||||
static void led_setonoff(unsigned int bits)
|
||||
{
|
||||
led_clrbits(CLRBITS(bits));
|
||||
led_setbits(SETBITS(bits));
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Public Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Name: up_ledinit
|
||||
****************************************************************************/
|
||||
|
||||
#ifdef CONFIG_ARCH_LEDS
|
||||
void up_ledinit(void)
|
||||
{
|
||||
/* Configure LED1 & LED2 GPIOs for output */
|
||||
stm32_configgpio(GPIO_LED1);
|
||||
stm32_configgpio(GPIO_LED2);
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: up_ledon
|
||||
****************************************************************************/
|
||||
|
||||
void up_ledon(int led)
|
||||
{
|
||||
led_setonoff(ON_BITS(g_ledbits[led]));
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: up_ledoff
|
||||
****************************************************************************/
|
||||
|
||||
void up_ledoff(int led)
|
||||
{
|
||||
led_setonoff(OFF_BITS(g_ledbits[led]));
|
||||
}
|
||||
|
||||
#endif /* CONFIG_ARCH_LEDS */
|
|
@ -0,0 +1,182 @@
|
|||
/****************************************************************************
|
||||
* config/hymini-stm32v/src/up_nsh.c
|
||||
* arch/arm/src/board/up_nsh.c
|
||||
*
|
||||
* Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <stdbool.h>
|
||||
#include <stdio.h>
|
||||
#include <debug.h>
|
||||
#include <errno.h>
|
||||
|
||||
#ifdef CONFIG_STM32_SPI1
|
||||
# include <nuttx/spi.h>
|
||||
# include <nuttx/mtd.h>
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_STM32_SDIO
|
||||
# include <nuttx/sdio.h>
|
||||
# include <nuttx/mmcsd.h>
|
||||
#endif
|
||||
|
||||
#include "stm32_internal.h"
|
||||
#include "hymini_stm32v-internal.h"
|
||||
|
||||
/****************************************************************************
|
||||
* Pre-Processor Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/* Configuration ************************************************************/
|
||||
|
||||
/* For now, don't build in any SPI1 support -- NSH is not using it */
|
||||
|
||||
#undef CONFIG_STM32_SPI1
|
||||
|
||||
|
||||
/* PORT and SLOT number probably depend on the board configuration */
|
||||
|
||||
#ifdef CONFIG_ARCH_BOARD_HYMINI_STM32V
|
||||
# define CONFIG_NSH_HAVEUSBDEV 1
|
||||
# define CONFIG_NSH_HAVEMMCSD 1
|
||||
# if defined(CONFIG_NSH_MMCSDSLOTNO) && CONFIG_NSH_MMCSDSLOTNO != 0
|
||||
# error "Only one MMC/SD slot"
|
||||
# undef CONFIG_NSH_MMCSDSLOTNO
|
||||
# endif
|
||||
# ifndef CONFIG_NSH_MMCSDSLOTNO
|
||||
# define CONFIG_NSH_MMCSDSLOTNO 0
|
||||
# endif
|
||||
#else
|
||||
/* Add configuration for new STM32 boards here */
|
||||
# error "Unrecognized STM32 board"
|
||||
# undef CONFIG_NSH_HAVEUSBDEV
|
||||
# undef CONFIG_NSH_HAVEMMCSD
|
||||
#endif
|
||||
|
||||
/* Can't support USB features if USB is not enabled */
|
||||
|
||||
#ifndef CONFIG_USBDEV
|
||||
# undef CONFIG_NSH_HAVEUSBDEV
|
||||
#endif
|
||||
|
||||
/* Can't support MMC/SD features if mountpoints are disabled or if SDIO support
|
||||
* is not enabled.
|
||||
*/
|
||||
|
||||
#if defined(CONFIG_DISABLE_MOUNTPOINT) || !defined(CONFIG_STM32_SDIO)
|
||||
# undef CONFIG_NSH_HAVEMMCSD
|
||||
#endif
|
||||
|
||||
#ifndef CONFIG_NSH_MMCSDMINOR
|
||||
# define CONFIG_NSH_MMCSDMINOR 0
|
||||
#endif
|
||||
|
||||
/* Debug ********************************************************************/
|
||||
|
||||
#ifdef CONFIG_CPP_HAVE_VARARGS
|
||||
# ifdef CONFIG_DEBUG
|
||||
# define message(...) lib_lowprintf(__VA_ARGS__)
|
||||
# else
|
||||
# define message(...) printf(__VA_ARGS__)
|
||||
# endif
|
||||
#else
|
||||
# ifdef CONFIG_DEBUG
|
||||
# define message lib_lowprintf
|
||||
# else
|
||||
# define message printf
|
||||
# endif
|
||||
#endif
|
||||
|
||||
/****************************************************************************
|
||||
* Public Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Name: nsh_archinitialize
|
||||
*
|
||||
* Description:
|
||||
* Perform architecture specific initialization
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
int nsh_archinitialize(void)
|
||||
{
|
||||
#ifdef CONFIG_NSH_HAVEMMCSD
|
||||
FAR struct sdio_dev_s *sdio;
|
||||
int ret;
|
||||
|
||||
/* Card detect */
|
||||
bool cd_status;
|
||||
#endif
|
||||
|
||||
/* Mount the SDIO-based MMC/SD block driver */
|
||||
|
||||
#ifdef CONFIG_NSH_HAVEMMCSD
|
||||
/* First, get an instance of the SDIO interface */
|
||||
|
||||
message("nsh_archinitialize: Initializing SDIO slot %d\n",
|
||||
CONFIG_NSH_MMCSDSLOTNO);
|
||||
sdio = sdio_initialize(CONFIG_NSH_MMCSDSLOTNO);
|
||||
if (!sdio)
|
||||
{
|
||||
message("nsh_archinitialize: Failed to initialize SDIO slot %d\n",
|
||||
CONFIG_NSH_MMCSDSLOTNO);
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
/* Now bind the SDIO interface to the MMC/SD driver */
|
||||
|
||||
message("nsh_archinitialize: Bind SDIO to the MMC/SD driver, minor=%d\n",
|
||||
CONFIG_NSH_MMCSDMINOR);
|
||||
ret = mmcsd_slotinitialize(CONFIG_NSH_MMCSDMINOR, sdio);
|
||||
if (ret != OK)
|
||||
{
|
||||
message("nsh_archinitialize: Failed to bind SDIO to the MMC/SD driver: %d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
message("nsh_archinitialize: Successfully bound SDIO to the MMC/SD driver\n");
|
||||
|
||||
/* Use SD card detect pin to check if a card is inserted */
|
||||
|
||||
cd_status = !stm32_gpioread(GPIO_SD_CD);
|
||||
message("Card detect : %hhu", cd_status);
|
||||
|
||||
sdio_mediachange(sdio, cd_status);
|
||||
#endif
|
||||
return OK;
|
||||
}
|
|
@ -0,0 +1,179 @@
|
|||
/************************************************************************************
|
||||
* configs/hymini-stm32v/src/up_spi.c
|
||||
* arch/arm/src/board/up_spi.c
|
||||
*
|
||||
* Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
* Laurent Latil <laurent@latil.nom.fr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <stdint.h>
|
||||
#include <stdbool.h>
|
||||
#include <debug.h>
|
||||
|
||||
#include <nuttx/spi.h>
|
||||
#include <arch/board/board.h>
|
||||
|
||||
#include "up_arch.h"
|
||||
#include "chip.h"
|
||||
#include "stm32_internal.h"
|
||||
#include "hymini_stm32v-internal.h"
|
||||
|
||||
#if defined(CONFIG_STM32_SPI1) || defined(CONFIG_STM32_SPI2)
|
||||
|
||||
/************************************************************************************
|
||||
* Definitions
|
||||
************************************************************************************/
|
||||
|
||||
/* Enables debug output from this file (needs CONFIG_DEBUG too) */
|
||||
|
||||
#define SPI_DEBUG /* Define to enable debug */
|
||||
#define SPI_VERBOSE /* Define to enable verbose debug */
|
||||
|
||||
#ifdef SPI_DEBUG
|
||||
# define spidbg lldbg
|
||||
# ifdef SPI_VERBOSE
|
||||
# define spivdbg lldbg
|
||||
# else
|
||||
# define spivdbg(x...)
|
||||
# endif
|
||||
#else
|
||||
# undef SPI_VERBOSE
|
||||
# define spidbg(x...)
|
||||
# define spivdbg(x...)
|
||||
#endif
|
||||
|
||||
/************************************************************************************
|
||||
* Private Functions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Public Functions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_spiinitialize
|
||||
*
|
||||
* Description:
|
||||
* Called to configure SPI chip select GPIO pins for the HY-MiniSTM32 board.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
void stm32_spiinitialize(void)
|
||||
{
|
||||
/* NOTE: Clocking for SPI1 and/or SPI2 was already provided in stm32_rcc.c.
|
||||
* Configurations of SPI pins is performed in stm32_spi.c.
|
||||
* Here, we only initialize chip select pins unique to the board
|
||||
* architecture.
|
||||
*/
|
||||
|
||||
#ifdef CONFIG_STM32_SPI1
|
||||
/* Configure the SPI-based touch screen CS GPIO */
|
||||
spivdbg("Configure GPIO for SPI1/CS\n");
|
||||
stm32_configgpio(GPIO_TS_CS);
|
||||
#endif
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: stm32_spi1/2/3select and stm32_spi1/2/3status
|
||||
*
|
||||
* Description:
|
||||
* The external functions, stm32_spi1/2/3select and stm32_spi1/2/3status must be
|
||||
* provided by board-specific logic. They are implementations of the select
|
||||
* and status methods of the SPI interface defined by struct spi_ops_s (see
|
||||
* include/nuttx/spi.h). All other methods (including up_spiinitialize())
|
||||
* are provided by common STM32 logic. To use this common SPI logic on your
|
||||
* board:
|
||||
*
|
||||
* 1. Provide logic in stm32_boardinitialize() to configure SPI chip select
|
||||
* pins.
|
||||
* 2. Provide stm32_spi1/2/3select() and stm32_spi1/2/3status() functions in your
|
||||
* board-specific logic. These functions will perform chip selection and
|
||||
* status operations using GPIOs in the way your board is configured.
|
||||
* 3. Add a calls to up_spiinitialize() in your low level application
|
||||
* initialization logic
|
||||
* 4. The handle returned by up_spiinitialize() may then be used to bind the
|
||||
* SPI driver to higher level logic (e.g., calling
|
||||
* mmcsd_spislotinitialize(), for example, will bind the SPI driver to
|
||||
* the SPI MMC/SD driver).
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
#ifdef CONFIG_STM32_SPI1
|
||||
void stm32_spi1select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
|
||||
{
|
||||
spidbg("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert");
|
||||
|
||||
if (devid == SPIDEV_TOUCHSCREEN)
|
||||
{
|
||||
/* Set the GPIO low to select and high to de-select */
|
||||
|
||||
stm32_gpiowrite(GPIO_TS_CS, !selected);
|
||||
}
|
||||
}
|
||||
|
||||
uint8_t stm32_spi1status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
|
||||
{
|
||||
return SPI_STATUS_PRESENT;
|
||||
}
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_STM32_SPI2
|
||||
void stm32_spi2select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
|
||||
{
|
||||
spidbg("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert");
|
||||
}
|
||||
|
||||
uint8_t stm32_spi2status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
|
||||
{
|
||||
return SPI_STATUS_PRESENT;
|
||||
}
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_STM32_SPI3
|
||||
void stm32_spi3select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
|
||||
{
|
||||
spidbg("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert");
|
||||
}
|
||||
|
||||
uint8_t stm32_spi3status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
|
||||
{
|
||||
return SPI_STATUS_PRESENT;
|
||||
}
|
||||
#endif
|
||||
|
||||
#endif /* CONFIG_STM32_SPI1 || CONFIG_STM32_SPI2 */
|
|
@ -0,0 +1,163 @@
|
|||
/************************************************************************************
|
||||
* configs/hymini-stm32v/src/up_ts.c
|
||||
* arch/arm/src/board/up_ts.c
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
* Laurent Latil <laurent@latil.nom.fr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
#include <nuttx/spi.h>
|
||||
#include <nuttx/arch.h>
|
||||
|
||||
#include <errno.h>
|
||||
#include <debug.h>
|
||||
|
||||
#include "stm32.h"
|
||||
#include "stm32_internal.h"
|
||||
#include "hymini_stm32v-internal.h"
|
||||
|
||||
#include <nuttx/input/ads7843e.h>
|
||||
|
||||
#if !defined(CONFIG_STM32_SPI1)
|
||||
# error CONFIG_STM32_SPI1 must be defined to use the ADS7843 on this board
|
||||
#endif
|
||||
|
||||
static int hymini_ts_irq_attach(FAR struct ads7843e_config_s *state, xcpt_t isr);
|
||||
static void hymini_ts_irq_enable(FAR struct ads7843e_config_s *state,
|
||||
bool enable);
|
||||
static void hymini_ts_irq_clear(FAR struct ads7843e_config_s *state);
|
||||
static bool hymini_ts_busy(FAR struct ads7843e_config_s *state);
|
||||
static bool hymini_ts_pendown(FAR struct ads7843e_config_s *state);
|
||||
|
||||
/************************************************************************************
|
||||
* Private Data
|
||||
************************************************************************************/
|
||||
|
||||
static FAR struct ads7843e_config_s ts_cfg =
|
||||
{
|
||||
.frequency = CONFIG_ADS7843E_FREQUENCY,
|
||||
|
||||
.attach = hymini_ts_irq_attach,
|
||||
.enable=hymini_ts_irq_enable,
|
||||
.clear=hymini_ts_irq_clear,
|
||||
.busy = hymini_ts_busy,
|
||||
.pendown=hymini_ts_pendown
|
||||
};
|
||||
|
||||
static xcpt_t tc_isr;
|
||||
|
||||
/************************************************************************************
|
||||
* Private Functions
|
||||
************************************************************************************/
|
||||
|
||||
/* Attach the ADS7843E interrupt handler to the GPIO interrupt */
|
||||
static int hymini_ts_irq_attach(FAR struct ads7843e_config_s *state, xcpt_t isr)
|
||||
{
|
||||
ivdbg("hymini_ts_irq_attach\n");
|
||||
|
||||
tc_isr = isr;
|
||||
stm32_gpiosetevent(GPIO_TS_IRQ, true, true, true, isr);
|
||||
return OK;
|
||||
}
|
||||
|
||||
/* Enable or disable the GPIO interrupt */
|
||||
static void hymini_ts_irq_enable(FAR struct ads7843e_config_s *state,
|
||||
bool enable)
|
||||
{
|
||||
illvdbg("%d\n", enable);
|
||||
|
||||
stm32_gpiosetevent(GPIO_TS_IRQ, true, true, true, enable? tc_isr:NULL);
|
||||
}
|
||||
|
||||
/* Acknowledge/clear any pending GPIO interrupt */
|
||||
static void hymini_ts_irq_clear(FAR struct ads7843e_config_s *state)
|
||||
{
|
||||
// FIXME Nothing to do ?
|
||||
}
|
||||
|
||||
/* As the busy line is not connected, we just wait a little bit here */
|
||||
static bool hymini_ts_busy(FAR struct ads7843e_config_s *state)
|
||||
{
|
||||
up_mdelay(50);
|
||||
return false;
|
||||
}
|
||||
|
||||
/* Return the state of the pen down GPIO input */
|
||||
static bool hymini_ts_pendown(FAR struct ads7843e_config_s *state)
|
||||
{
|
||||
bool pin_value = stm32_gpioread(GPIO_TS_IRQ);
|
||||
return !pin_value;
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: arch_tcinitialize()
|
||||
*
|
||||
* Description:
|
||||
* Perform architecture-specific initialization of the touchscreen.
|
||||
* This function must be called directly from application.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
int arch_tcinitialize(int minor)
|
||||
{
|
||||
FAR struct spi_dev_s *dev;
|
||||
|
||||
idbg("arch_tcinitialize: minor %d\n", minor);
|
||||
|
||||
dev = up_spiinitialize(1);
|
||||
if (!dev)
|
||||
{
|
||||
idbg("arch_tcinitialize: Failed to initialize SPI bus\n");
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
/* Configure the PIO interrupt */
|
||||
|
||||
stm32_configgpio(GPIO_TS_IRQ);
|
||||
|
||||
return ads7843e_register(dev, &ts_cfg, minor);
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: arch_tcuninitialize()
|
||||
*
|
||||
* Description:
|
||||
* Perform architecture-specific un-initialization of the touchscreen
|
||||
* hardware. This function must be called directly from application.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
void arch_tcuninitialize(void)
|
||||
{
|
||||
/* FIXME What can/should we do here ? */
|
||||
}
|
|
@ -0,0 +1,117 @@
|
|||
/************************************************************************************
|
||||
* configs/hymini-stm32v/src/up_usbdev.c
|
||||
* arch/arm/src/board/up_boot.c
|
||||
*
|
||||
* Copyright (C) 2009-2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <sys/types.h>
|
||||
#include <stdint.h>
|
||||
#include <stdbool.h>
|
||||
#include <debug.h>
|
||||
|
||||
#include <nuttx/usb/usbdev.h>
|
||||
#include <nuttx/usb/usbdev_trace.h>
|
||||
|
||||
#include "up_arch.h"
|
||||
#include "stm32_internal.h"
|
||||
#include "hymini_stm32v-internal.h"
|
||||
|
||||
/************************************************************************************
|
||||
* Definitions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Private Functions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Public Functions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_usbinitialize
|
||||
*
|
||||
* Description:
|
||||
* Called to setup USB-related GPIO pins for the Hy-Mini STM32v board.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
void stm32_usbinitialize(void)
|
||||
{
|
||||
ulldbg("called\n");
|
||||
|
||||
/* USB Soft Connect Pullup */
|
||||
stm32_configgpio(GPIO_USB_PULLUP);
|
||||
}
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_usbpullup
|
||||
*
|
||||
* Description:
|
||||
* If USB is supported and the board supports a pullup via GPIO (for USB software
|
||||
* connect and disconnect), then the board software must provide stm32_pullup.
|
||||
* See include/nuttx/usb/usbdev.h for additional description of this method.
|
||||
* Alternatively, if no pull-up GPIO the following EXTERN can be redefined to be
|
||||
* NULL.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
int stm32_usbpullup(FAR struct usbdev_s *dev, bool enable)
|
||||
{
|
||||
usbtrace(TRACE_DEVPULLUP, (uint16_t)enable);
|
||||
stm32_gpiowrite(GPIO_USB_PULLUP, !enable);
|
||||
return OK;
|
||||
}
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_usbsuspend
|
||||
*
|
||||
* Description:
|
||||
* Board logic must provide the stm32_usbsuspend logic if the USBDEV driver is
|
||||
* used. This function is called whenever the USB enters or leaves suspend mode.
|
||||
* This is an opportunity for the board logic to shutdown clocks, power, etc.
|
||||
* while the USB is suspended.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
void stm32_usbsuspend(FAR struct usbdev_s *dev, bool resume)
|
||||
{
|
||||
ulldbg("resume: %d\n", resume);
|
||||
}
|
||||
|
|
@ -0,0 +1,164 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/src/up_usbstrg.c
|
||||
*
|
||||
* Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Configure and register the STM32 MMC/SD SDIO block driver.
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <stdio.h>
|
||||
#include <debug.h>
|
||||
#include <errno.h>
|
||||
|
||||
#include <nuttx/sdio.h>
|
||||
#include <nuttx/mmcsd.h>
|
||||
|
||||
#include "stm32_internal.h"
|
||||
|
||||
/* There is nothing to do here if SDIO support is not selected. */
|
||||
|
||||
#ifdef CONFIG_STM32_SDIO
|
||||
|
||||
/****************************************************************************
|
||||
* Pre-Processor Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/* Configuration ************************************************************/
|
||||
|
||||
#ifndef CONFIG_EXAMPLES_USBSTRG_DEVMINOR1
|
||||
# define CONFIG_EXAMPLES_USBSTRG_DEVMINOR1 0
|
||||
#endif
|
||||
|
||||
/* SLOT number(s) could depend on the board configuration */
|
||||
|
||||
#ifdef CONFIG_ARCH_BOARD_HYMINI_STM32V
|
||||
# undef STM32_MMCSDSLOTNO
|
||||
# define STM32_MMCSDSLOTNO 0
|
||||
#else
|
||||
/* Add configuration for new STM32 boards here */
|
||||
# error "Unrecognized STM32 board"
|
||||
#endif
|
||||
|
||||
/* Debug ********************************************************************/
|
||||
|
||||
#ifdef CONFIG_CPP_HAVE_VARARGS
|
||||
# ifdef CONFIG_DEBUG
|
||||
# define message(...) lib_lowprintf(__VA_ARGS__)
|
||||
# define msgflush()
|
||||
# else
|
||||
# define message(...) printf(__VA_ARGS__)
|
||||
# define msgflush() fflush(stdout)
|
||||
# endif
|
||||
#else
|
||||
# ifdef CONFIG_DEBUG
|
||||
# define message lib_lowprintf
|
||||
# define msgflush()
|
||||
# else
|
||||
# define message printf
|
||||
# define msgflush() fflush(stdout)
|
||||
# endif
|
||||
#endif
|
||||
|
||||
|
||||
/****************************************************************************
|
||||
* Public Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Name: usbstrg_archinitialize
|
||||
*
|
||||
* Description:
|
||||
* Perform architecture specific initialization
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
int usbstrg_archinitialize(void)
|
||||
{
|
||||
/* If examples/usbstrg is built as an NSH command, then SD slot should
|
||||
* already have been initialized in nsh_archinitialize() (see up_nsh.c). In
|
||||
* this case, there is nothing further to be done here.
|
||||
*/
|
||||
|
||||
#ifndef CONFIG_EXAMPLES_USBSTRG_BUILTIN
|
||||
FAR struct sdio_dev_s *sdio;
|
||||
int ret;
|
||||
|
||||
/* First, get an instance of the SDIO interface */
|
||||
|
||||
message("usbstrg_archinitialize: "
|
||||
"Initializing SDIO slot %d\n",
|
||||
STM32_MMCSDSLOTNO);
|
||||
|
||||
sdio = sdio_initialize(STM32_MMCSDSLOTNO);
|
||||
if (!sdio)
|
||||
{
|
||||
message("usbstrg_archinitialize: Failed to initialize SDIO slot %d\n",
|
||||
STM32_MMCSDSLOTNO);
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
/* Now bind the SDIO interface to the MMC/SD driver */
|
||||
|
||||
message("usbstrg_archinitialize: "
|
||||
"Bind SDIO to the MMC/SD driver, minor=%d\n",
|
||||
CONFIG_EXAMPLES_USBSTRG_DEVMINOR1);
|
||||
|
||||
ret = mmcsd_slotinitialize(CONFIG_EXAMPLES_USBSTRG_DEVMINOR1, sdio);
|
||||
if (ret != OK)
|
||||
{
|
||||
message("usbstrg_archinitialize: "
|
||||
"Failed to bind SDIO to the MMC/SD driver: %d\n",
|
||||
ret);
|
||||
return ret;
|
||||
}
|
||||
message("usbstrg_archinitialize: "
|
||||
"Successfully bound SDIO to the MMC/SD driver\n");
|
||||
|
||||
/* Then let's guess and say that there is a card in the slot. I need to check to
|
||||
* see if the Hy-Mini STM32v board supports a GPIO to detect if there is a card in
|
||||
* the slot.
|
||||
*/
|
||||
|
||||
sdio_mediachange(sdio, true);
|
||||
|
||||
#endif /* CONFIG_EXAMPLES_USBSTRG_BUILTIN */
|
||||
|
||||
return OK;
|
||||
}
|
||||
|
||||
#endif /* CONFIG_STM32_SDIO */
|
|
@ -0,0 +1,174 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/usbserial/Make.defs
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include ${TOPDIR}/.config
|
||||
|
||||
# Setup for the selected toolchain
|
||||
|
||||
ifeq ($(CONFIG_STM32_DFU),y)
|
||||
LDSCRIPT = ld.script.dfu
|
||||
else
|
||||
LDSCRIPT = ld.script
|
||||
endif
|
||||
|
||||
ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
|
||||
# CodeSourcery under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
|
||||
# CodeSourcery under Linux
|
||||
CROSSDEV = arm-none-eabi-
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -O2
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_DEVKITARM),y)
|
||||
# devkitARM under Windows
|
||||
CROSSDEV = arm-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_RAISONANCE),y)
|
||||
# Raisonance RIDE7 under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_BUILDROOT),y)
|
||||
# NuttX buildroot under Linux or Cygwin
|
||||
CROSSDEV = arm-elf-
|
||||
ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -Os
|
||||
endif
|
||||
|
||||
ifeq ($(WINTOOL),y)
|
||||
# Windows-native toolchains
|
||||
DIRLINK = $(TOPDIR)/tools/winlink.sh
|
||||
DIRUNLINK = $(TOPDIR)/tools/unlink.sh
|
||||
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
|
||||
ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/usbserial/$(LDSCRIPT)}"
|
||||
MAXOPTIMIZATION = -O2
|
||||
else
|
||||
# Linux/Cygwin-native toolchain
|
||||
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
||||
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
||||
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/usbserial/$(LDSCRIPT)
|
||||
endif
|
||||
|
||||
CC = $(CROSSDEV)gcc
|
||||
CXX = $(CROSSDEV)g++
|
||||
CPP = $(CROSSDEV)gcc -E
|
||||
LD = $(CROSSDEV)ld
|
||||
AR = $(CROSSDEV)ar rcs
|
||||
NM = $(CROSSDEV)nm
|
||||
OBJCOPY = $(CROSSDEV)objcopy
|
||||
OBJDUMP = $(CROSSDEV)objdump
|
||||
|
||||
ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
|
||||
ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
|
||||
|
||||
ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
|
||||
ARCHOPTIMIZATION = -g
|
||||
else
|
||||
ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
|
||||
endif
|
||||
|
||||
ARCHCFLAGS = -fno-builtin
|
||||
ARCHCXXFLAGS = -fno-builtin -fno-exceptions
|
||||
ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
|
||||
ARCHWARNINGSXX = -Wall -Wshadow
|
||||
ARCHDEFINES =
|
||||
ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
|
||||
|
||||
CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
|
||||
CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
|
||||
CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
|
||||
AFLAGS = $(CFLAGS) -D__ASSEMBLY__
|
||||
|
||||
NXFLATLDFLAGS1 = -r -d -warn-common
|
||||
NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
|
||||
LDNXFLATFLAGS = -e main -s 2048
|
||||
|
||||
OBJEXT = .o
|
||||
LIBEXT = .a
|
||||
EXEEXT =
|
||||
|
||||
ifneq ($(CROSSDEV),arm-elf-)
|
||||
LDFLAGS += -nostartfiles -nodefaultlibs
|
||||
endif
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
LDFLAGS += -g
|
||||
endif
|
||||
|
||||
define PREPROCESS
|
||||
@echo "CPP: $1->$2"
|
||||
@$(CPP) $(CPPFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILE
|
||||
@echo "CC: $1"
|
||||
@$(CC) -c $(CFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILEXX
|
||||
@echo "CXX: $1"
|
||||
@$(CXX) -c $(CXXFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ASSEMBLE
|
||||
@echo "AS: $1"
|
||||
@$(CC) -c $(AFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ARCHIVE
|
||||
echo "AR: $2"; \
|
||||
$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
|
||||
endef
|
||||
|
||||
define CLEAN
|
||||
@rm -f *.o *.a
|
||||
endef
|
||||
|
||||
HOSTCC = gcc
|
||||
HOSTINCLUDES = -I.
|
||||
HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
|
||||
HOSTLDFLAGS =
|
||||
|
|
@ -0,0 +1,39 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/usbserial/appconfig
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
# Path to example in apps/examples containing the user_start entry point
|
||||
|
||||
CONFIGURED_APPS += examples/usbserial
|
||||
|
|
@ -0,0 +1,953 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/usbserial/defconfig
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
#
|
||||
# architecture selection
|
||||
#
|
||||
# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
|
||||
# processor architecture.
|
||||
# CONFIG_ARCH_family - for use in C code. This identifies the
|
||||
# particular chip family that the architecture is implemented
|
||||
# in.
|
||||
# CONFIG_ARCH_architecture - for use in C code. This identifies the
|
||||
# specific architecture within the chip familyl.
|
||||
# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||||
# CONFIG_ARCH_CHIP_name - For use in C code
|
||||
# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
|
||||
# the board that supports the particular chip or SoC.
|
||||
# CONFIG_ARCH_BOARD_name - for use in C code
|
||||
# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
|
||||
# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
|
||||
# CONFIG_DRAM_SIZE - Describes the installed DRAM.
|
||||
# CONFIG_DRAM_START - The start address of DRAM (physical)
|
||||
# CONFIG_DRAM_END - Last address+1 of installed RAM
|
||||
# CONFIG_ARCH_IRQPRIO - The ST32F103Z supports interrupt prioritization
|
||||
# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
||||
# stack. If defined, this symbol is the size of the interrupt
|
||||
# stack in bytes. If not defined, the user task stacks will be
|
||||
# used during interrupt handling.
|
||||
# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||||
# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
|
||||
# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
||||
# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture.
|
||||
# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
||||
# cause a 100 second delay during boot-up. This 100 second delay
|
||||
# serves no purpose other than it allows you to calibrate
|
||||
# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure
|
||||
# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
|
||||
# the delay actually is 100 seconds.
|
||||
# CONFIG_ARCH_DMA - Support DMA initialization
|
||||
#
|
||||
CONFIG_ARCH=arm
|
||||
CONFIG_ARCH_ARM=y
|
||||
CONFIG_ARCH_CORTEXM3=y
|
||||
CONFIG_ARCH_CHIP=stm32
|
||||
CONFIG_ARCH_CHIP_STM32F103VCT6=y
|
||||
CONFIG_ARCH_BOARD=hymini-stm32v
|
||||
CONFIG_ARCH_BOARD_HYMINI_STM32V=y
|
||||
|
||||
CONFIG_BOARD_LOOPSPERMSEC=5483
|
||||
CONFIG_DRAM_SIZE=0x0000C000
|
||||
CONFIG_DRAM_START=0x20000000
|
||||
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
||||
CONFIG_ARCH_IRQPRIO=y
|
||||
CONFIG_ARCH_INTERRUPTSTACK=n
|
||||
CONFIG_ARCH_STACKDUMP=y
|
||||
CONFIG_ARCH_BOOTLOADER=n
|
||||
CONFIG_ARCH_LEDS=y
|
||||
CONFIG_ARCH_BUTTONS=n
|
||||
CONFIG_ARCH_CALIBRATION=n
|
||||
CONFIG_ARCH_DMA=n
|
||||
|
||||
#
|
||||
# Identify toolchain and linker options
|
||||
#
|
||||
CONFIG_STM32_CODESOURCERYW=n
|
||||
CONFIG_STM32_CODESOURCERYL=y
|
||||
CONFIG_STM32_DEVKITARM=n
|
||||
CONFIG_STM32_RAISONANCE=n
|
||||
CONFIG_STM32_BUILDROOT=n
|
||||
CONFIG_STM32_DFU=n
|
||||
|
||||
#
|
||||
# Individual subsystems can be enabled:
|
||||
#
|
||||
# Individual subsystems can be enabled:
|
||||
# AHB:
|
||||
CONFIG_STM32_DMA1=n
|
||||
CONFIG_STM32_DMA2=n
|
||||
CONFIG_STM32_CRC=n
|
||||
CONFIG_STM32_FSMC=y
|
||||
CONFIG_STM32_SDIO=n
|
||||
# APB1:
|
||||
CONFIG_STM32_TIM2=n
|
||||
CONFIG_STM32_TIM3=n
|
||||
CONFIG_STM32_TIM4=n
|
||||
CONFIG_STM32_TIM5=n
|
||||
CONFIG_STM32_TIM6=n
|
||||
CONFIG_STM32_TIM7=n
|
||||
CONFIG_STM32_WWDG=n
|
||||
CONFIG_STM32_SPI2=n
|
||||
CONFIG_STM32_SPI4=n
|
||||
CONFIG_STM32_USART2=y
|
||||
CONFIG_STM32_USART3=n
|
||||
CONFIG_STM32_UART4=n
|
||||
CONFIG_STM32_UART5=n
|
||||
CONFIG_STM32_I2C1=n
|
||||
CONFIG_STM32_I2C2=n
|
||||
CONFIG_STM32_USB=y
|
||||
CONFIG_STM32_CAN=n
|
||||
CONFIG_STM32_BKP=n
|
||||
CONFIG_STM32_PWR=n
|
||||
CONFIG_STM32_DAC=n
|
||||
# APB2:
|
||||
CONFIG_STM32_ADC1=n
|
||||
CONFIG_STM32_ADC2=n
|
||||
CONFIG_STM32_TIM1=n
|
||||
CONFIG_STM32_SPI1=n
|
||||
CONFIG_STM32_TIM8=n
|
||||
CONFIG_STM32_USART1=y
|
||||
CONFIG_STM32_ADC3=n
|
||||
|
||||
#
|
||||
# Timer and I2C devices may need to the following to force power to be applied:
|
||||
#
|
||||
#CONFIG_STM32_FORCEPOWER=y
|
||||
|
||||
#
|
||||
# STM32F103V specific serial device driver settings
|
||||
#
|
||||
# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
|
||||
# console and ttys0 (default is the USART1).
|
||||
# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
|
||||
# This specific the size of the receive buffer
|
||||
# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
|
||||
# being sent. This specific the size of the transmit buffer
|
||||
# CONFIG_USARTn_BAUD - The configure BAUD of the UART. Must be
|
||||
# CONFIG_USARTn_BITS - The number of bits. Must be either 7 or 8.
|
||||
# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
||||
# CONFIG_USARTn_2STOP - Two stop bits
|
||||
#
|
||||
CONFIG_USART1_SERIAL_CONSOLE=y
|
||||
CONFIG_USART2_SERIAL_CONSOLE=n
|
||||
CONFIG_USART3_SERIAL_CONSOLE=n
|
||||
CONFIG_USART4_SERIAL_CONSOLE=n
|
||||
CONFIG_USART5_SERIAL_CONSOLE=n
|
||||
|
||||
CONFIG_USART1_TXBUFSIZE=256
|
||||
CONFIG_USART2_TXBUFSIZE=256
|
||||
CONFIG_USART3_TXBUFSIZE=256
|
||||
CONFIG_USART4_TXBUFSIZE=256
|
||||
CONFIG_USART5_TXBUFSIZE=256
|
||||
|
||||
CONFIG_USART1_RXBUFSIZE=256
|
||||
CONFIG_USART2_RXBUFSIZE=256
|
||||
CONFIG_USART3_RXBUFSIZE=256
|
||||
CONFIG_USART4_RXBUFSIZE=256
|
||||
CONFIG_USART5_RXBUFSIZE=256
|
||||
|
||||
CONFIG_USART1_BAUD=115200
|
||||
CONFIG_USART2_BAUD=115200
|
||||
CONFIG_USART3_BAUD=115200
|
||||
CONFIG_USART4_BAUD=115200
|
||||
CONFIG_USART5_BAUD=115200
|
||||
|
||||
CONFIG_USART1_BITS=8
|
||||
CONFIG_USART2_BITS=8
|
||||
CONFIG_USART3_BITS=8
|
||||
CONFIG_USART4_BITS=8
|
||||
CONFIG_USART5_BITS=8
|
||||
|
||||
CONFIG_USART1_PARITY=0
|
||||
CONFIG_USART2_PARITY=0
|
||||
CONFIG_USART3_PARITY=0
|
||||
CONFIG_USART4_PARITY=0
|
||||
CONFIG_USART5_PARITY=0
|
||||
|
||||
CONFIG_USART1_2STOP=0
|
||||
CONFIG_USART2_2STOP=0
|
||||
CONFIG_USART3_2STOP=0
|
||||
CONFIG_USART4_2STOP=0
|
||||
CONFIG_USART5_2STOP=0
|
||||
|
||||
#
|
||||
# STM32F103V specific SSI device driver settings
|
||||
#
|
||||
# CONFIG_SSIn_DISABLE - select to disable all support for
|
||||
# the SSI
|
||||
# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
|
||||
# Poll-waiting is recommended if the interrupt rate would be to
|
||||
# high in the interrupt driven case.
|
||||
# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
|
||||
# emptying the Rx FIFO. If the SPI frequency is high and this
|
||||
# value is large, then larger values of this setting may cause
|
||||
# Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
|
||||
#
|
||||
CONFIG_SSI0_DISABLE=n
|
||||
CONFIG_SSI1_DISABLE=y
|
||||
CONFIG_SSI_POLLWAIT=y
|
||||
#CONFIG_SSI_TXLIMIT=4
|
||||
|
||||
#
|
||||
# General build options
|
||||
#
|
||||
# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
|
||||
# BSPs from www.ridgerun.com using the tools/mkimage.sh script
|
||||
# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_RAW_BINARY - make a raw binary format file used with many
|
||||
# different loaders using the GNU objcopy program. This option
|
||||
# should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_HAVE_LIBM - toolchain supports libm.a
|
||||
#
|
||||
CONFIG_RRLOAD_BINARY=n
|
||||
CONFIG_INTELHEX_BINARY=n
|
||||
CONFIG_MOTOROLA_SREC=n
|
||||
CONFIG_RAW_BINARY=y
|
||||
CONFIG_HAVE_LIBM=n
|
||||
|
||||
#
|
||||
# General OS setup
|
||||
#
|
||||
# CONFIG_APPS_DIR - Identifies the relative path to the directory
|
||||
# that builds the application to link with NuttX. Default: ../apps
|
||||
# CONFIG_DEBUG - enables built-in debug options
|
||||
# CONFIG_DEBUG_VERBOSE - enables verbose debug output
|
||||
# CONFIG_DEBUG_SYMBOLS - build without optimization and with
|
||||
# debug symbols (needed for use with a debugger).
|
||||
# CONFIG_MM_REGIONS - If the architecture includes multiple
|
||||
# regions of memory to allocate from, this specifies the
|
||||
# number of memory regions that the memory manager must
|
||||
# handle and enables the API mm_addregion(start, end);
|
||||
# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
|
||||
# time console output
|
||||
# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
|
||||
# or MSEC_PER_TICK=10. This setting may be defined to
|
||||
# inform NuttX that the processor hardware is providing
|
||||
# system timer interrupts at some interrupt interval other
|
||||
# than 10 msec.
|
||||
# CONFIG_RR_INTERVAL - The round robin timeslice will be set
|
||||
# this number of milliseconds; Round robin scheduling can
|
||||
# be disabled by setting this value to zero.
|
||||
# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in
|
||||
# scheduler to monitor system performance
|
||||
# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
|
||||
# task name to save in the TCB. Useful if scheduler
|
||||
# instrumentation is selected. Set to zero to disable.
|
||||
# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
|
||||
# Used to initialize the internal time logic.
|
||||
# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
|
||||
# You would only need this if you are concerned about accurate
|
||||
# time conversions in the past or in the distant future.
|
||||
# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
|
||||
# would only need this if you are concerned about accurate
|
||||
# time conversion in the distand past. You must also define
|
||||
# CONFIG_GREGORIAN_TIME in order to use Julian time.
|
||||
# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
|
||||
# provides /dev/console. Enables stdout, stderr, stdin.
|
||||
# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
|
||||
# driver (minimul support)
|
||||
# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
|
||||
# errorcheck mutexes. Enables pthread_mutexattr_settype().
|
||||
# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
|
||||
# inheritance on mutexes and semaphores.
|
||||
# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
|
||||
# inheritance is enabled. It defines the maximum number of
|
||||
# different threads (minus one) that can take counts on a
|
||||
# semaphore with priority inheritance support. This may be
|
||||
# set to zero if priority inheritance is disabled OR if you
|
||||
# are only using semaphores as mutexes (only one holder) OR
|
||||
# if no more than two threads participate using a counting
|
||||
# semaphore.
|
||||
# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled,
|
||||
# then this setting is the maximum number of higher priority
|
||||
# threads (minus 1) than can be waiting for another thread
|
||||
# to release a count on a semaphore. This value may be set
|
||||
# to zero if no more than one thread is expected to wait for
|
||||
# a semaphore.
|
||||
# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
|
||||
# by task_create() when a new task is started. If set, all
|
||||
# files/drivers will appear to be closed in the new task.
|
||||
# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
|
||||
# three file descriptors (stdin, stdout, stderr) by task_create()
|
||||
# when a new task is started. If set, all files/drivers will
|
||||
# appear to be closed in the new task except for stdin, stdout,
|
||||
# and stderr.
|
||||
# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
|
||||
# desciptors by task_create() when a new task is started. If
|
||||
# set, all sockets will appear to be closed in the new task.
|
||||
# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
|
||||
# This format will support execution of NuttX binaries located
|
||||
# in a ROMFS filesystem (see examples/nxflat).
|
||||
# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to
|
||||
# handle delayed processing from interrupt handlers. This feature
|
||||
# is required for some drivers but, if there are not complaints,
|
||||
# can be safely disabled. The worker thread also performs
|
||||
# garbage collection -- completing any delayed memory deallocations
|
||||
# from interrupt handlers. If the worker thread is disabled,
|
||||
# then that clean will be performed by the IDLE thread instead
|
||||
# (which runs at the lowest of priority and may not be appropriate
|
||||
# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE
|
||||
# is enabled, then the following options can also be used:
|
||||
# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
|
||||
# thread. Default: 50
|
||||
# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
|
||||
# work in units of microseconds. Default: 50*1000 (50 MS).
|
||||
# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
|
||||
# thread. Default: CONFIG_IDLETHREAD_STACKSIZE.
|
||||
# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
|
||||
# the worker thread. Default: 4
|
||||
#
|
||||
#CONFIG_APPS_DIR=
|
||||
CONFIG_DEBUG=n
|
||||
CONFIG_DEBUG_VERBOSE=n
|
||||
CONFIG_DEBUG_USB=n
|
||||
CONFIG_DEBUG_SYMBOLS=n
|
||||
CONFIG_MM_REGIONS=1
|
||||
CONFIG_ARCH_LOWPUTC=y
|
||||
CONFIG_RR_INTERVAL=200
|
||||
CONFIG_SCHED_INSTRUMENTATION=n
|
||||
CONFIG_TASK_NAME_SIZE=0
|
||||
CONFIG_START_YEAR=2009
|
||||
CONFIG_START_MONTH=10
|
||||
CONFIG_START_DAY=23
|
||||
CONFIG_GREGORIAN_TIME=n
|
||||
CONFIG_JULIAN_TIME=n
|
||||
CONFIG_DEV_CONSOLE=y
|
||||
CONFIG_DEV_LOWCONSOLE=n
|
||||
CONFIG_MUTEX_TYPES=n
|
||||
CONFIG_PRIORITY_INHERITANCE=n
|
||||
CONFIG_SEM_PREALLOCHOLDERS=0
|
||||
CONFIG_SEM_NNESTPRIO=0
|
||||
CONFIG_FDCLONE_DISABLE=n
|
||||
CONFIG_FDCLONE_STDIO=n
|
||||
CONFIG_SDCLONE_DISABLE=y
|
||||
CONFIG_NXFLAT=n
|
||||
CONFIG_SCHED_WORKQUEUE=n
|
||||
CONFIG_SCHED_WORKPRIORITY=50
|
||||
CONFIG_SCHED_WORKPERIOD=(50*1000)
|
||||
CONFIG_SCHED_WORKSTACKSIZE=1024
|
||||
CONFIG_SIG_SIGWORK=4
|
||||
|
||||
#
|
||||
# The following can be used to disable categories of
|
||||
# APIs supported by the OS. If the compiler supports
|
||||
# weak functions, then it should not be necessary to
|
||||
# disable functions unless you want to restrict usage
|
||||
# of those APIs.
|
||||
#
|
||||
# There are certain dependency relationships in these
|
||||
# features.
|
||||
#
|
||||
# o mq_notify logic depends on signals to awaken tasks
|
||||
# waiting for queues to become full or empty.
|
||||
# o pthread_condtimedwait() depends on signals to wake
|
||||
# up waiting tasks.
|
||||
#
|
||||
CONFIG_DISABLE_CLOCK=n
|
||||
CONFIG_DISABLE_POSIX_TIMERS=n
|
||||
CONFIG_DISABLE_PTHREAD=n
|
||||
CONFIG_DISABLE_SIGNALS=n
|
||||
CONFIG_DISABLE_MQUEUE=n
|
||||
CONFIG_DISABLE_MOUNTPOINT=y
|
||||
CONFIG_DISABLE_ENVIRON=n
|
||||
CONFIG_DISABLE_POLL=y
|
||||
|
||||
#
|
||||
# Misc libc settings
|
||||
#
|
||||
# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
|
||||
# little smaller if we do not support fieldwidthes
|
||||
#
|
||||
CONFIG_NOPRINTF_FIELDWIDTH=n
|
||||
|
||||
#
|
||||
# Allow for architecture optimized implementations
|
||||
#
|
||||
# The architecture can provide optimized versions of the
|
||||
# following to improve system performance
|
||||
#
|
||||
CONFIG_ARCH_MEMCPY=n
|
||||
CONFIG_ARCH_MEMCMP=n
|
||||
CONFIG_ARCH_MEMMOVE=n
|
||||
CONFIG_ARCH_MEMSET=n
|
||||
CONFIG_ARCH_STRCMP=n
|
||||
CONFIG_ARCH_STRCPY=n
|
||||
CONFIG_ARCH_STRNCPY=n
|
||||
CONFIG_ARCH_STRLEN=n
|
||||
CONFIG_ARCH_STRNLEN=n
|
||||
CONFIG_ARCH_BZERO=n
|
||||
|
||||
#
|
||||
# Sizes of configurable things (0 disables)
|
||||
#
|
||||
# CONFIG_MAX_TASKS - The maximum number of simultaneously
|
||||
# active tasks. This value must be a power of two.
|
||||
# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
|
||||
# of parameters that a task may receive (i.e., maxmum value
|
||||
# of 'argc')
|
||||
# CONFIG_NPTHREAD_KEYS - The number of items of thread-
|
||||
# specific data that can be retained
|
||||
# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
|
||||
# descriptors (one for each open)
|
||||
# CONFIG_NFILE_STREAMS - The maximum number of streams that
|
||||
# can be fopen'ed
|
||||
# CONFIG_NAME_MAX - The maximum size of a file name.
|
||||
# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
|
||||
# on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_NUNGET_CHARS - Number of characters that can be
|
||||
# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
|
||||
# structures. The system manages a pool of preallocated
|
||||
# message structures to minimize dynamic allocations
|
||||
# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
|
||||
# a fixed payload size given by this settin (does not include
|
||||
# other message structure overhead.
|
||||
# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
|
||||
# can be passed to a watchdog handler
|
||||
# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
|
||||
# structures. The system manages a pool of preallocated
|
||||
# watchdog structures to minimize dynamic allocations
|
||||
# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
|
||||
# timer structures. The system manages a pool of preallocated
|
||||
# timer structures to minimize dynamic allocations. Set to
|
||||
# zero for all dynamic allocations.
|
||||
#
|
||||
CONFIG_MAX_TASKS=16
|
||||
CONFIG_MAX_TASK_ARGS=4
|
||||
CONFIG_NPTHREAD_KEYS=4
|
||||
CONFIG_NFILE_DESCRIPTORS=8
|
||||
CONFIG_NFILE_STREAMS=8
|
||||
CONFIG_NAME_MAX=32
|
||||
CONFIG_STDIO_BUFFER_SIZE=256
|
||||
CONFIG_NUNGET_CHARS=2
|
||||
CONFIG_PREALLOC_MQ_MSGS=4
|
||||
CONFIG_MQ_MAXMSGSIZE=32
|
||||
CONFIG_MAX_WDOGPARMS=2
|
||||
CONFIG_PREALLOC_WDOGS=4
|
||||
CONFIG_PREALLOC_TIMERS=4
|
||||
|
||||
#
|
||||
# Filesystem configuration
|
||||
#
|
||||
# CONFIG_FS_FAT - Enable FAT filesystem support
|
||||
# CONFIG_FAT_SECTORSIZE - Max supported sector size
|
||||
# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
|
||||
# file name support.
|
||||
# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims
|
||||
# patents on FAT long file name technology. Please read the
|
||||
# disclaimer in the top-level COPYING file and only enable this
|
||||
# feature if you understand these issues.
|
||||
# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
|
||||
# default, maximum long file name is 255 bytes. This can eat up
|
||||
# a lot of memory (especially stack space). If you are willing
|
||||
# to live with some non-standard, short long file names, then
|
||||
# define this value. A good choice would be the same value as
|
||||
# selected for CONFIG_NAME_MAX which will limit the visibility
|
||||
# of longer file names anyway.
|
||||
# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
|
||||
# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH.
|
||||
# This must have one of the values of 0xff or 0x00.
|
||||
# Default: 0xff.
|
||||
# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
|
||||
# don't both with file chunks smaller than this number of data bytes.
|
||||
# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
|
||||
# Default: 255.
|
||||
# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
|
||||
# don't both with file chunks smaller than this number of data bytes.
|
||||
# Default: 32.
|
||||
# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
|
||||
# packing files together toward the end of the file or, if file are
|
||||
# deleted at the end of the file, clean up can simply mean erasing
|
||||
# the end of FLASH memory so that it can be re-used again. However,
|
||||
# doing this can also harm the life of the FLASH part because it can
|
||||
# mean that the tail end of the FLASH is re-used too often. This
|
||||
# threshold determines if/when it is worth erased the tail end of FLASH
|
||||
# and making it available for re-use (and possible over-wear).
|
||||
# Default: 8192.
|
||||
# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
|
||||
# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
|
||||
# option will enable a limited form of memory mapping that is
|
||||
# implemented by copying whole files into memory.
|
||||
#
|
||||
CONFIG_FS_FAT=n
|
||||
CONFIG_FAT_LCNAMES=n
|
||||
CONFIG_FAT_LFN=n
|
||||
CONFIG_FAT_MAXFNAME=32
|
||||
CONFIG_FS_NXFFS=n
|
||||
CONFIG_FS_ROMFS=n
|
||||
|
||||
#
|
||||
# SPI-based MMC/SD driver
|
||||
#
|
||||
# CONFIG_MMCSD_NSLOTS
|
||||
# Number of MMC/SD slots supported by the driver
|
||||
# CONFIG_MMCSD_READONLY
|
||||
# Provide read-only access (default is read/write)
|
||||
# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
|
||||
# Default is 20MHz.
|
||||
#
|
||||
CONFIG_MMCSD_NSLOTS=1
|
||||
CONFIG_MMCSD_READONLY=n
|
||||
CONFIG_MMCSD_SPICLOCK=12500000
|
||||
|
||||
#
|
||||
# Block driver buffering
|
||||
#
|
||||
# CONFIG_FS_READAHEAD
|
||||
# Enable read-ahead buffering
|
||||
# CONFIG_FS_WRITEBUFFER
|
||||
# Enable write buffering
|
||||
#
|
||||
CONFIG_FS_READAHEAD=n
|
||||
CONFIG_FS_WRITEBUFFER=n
|
||||
|
||||
#
|
||||
# SDIO-based MMC/SD driver
|
||||
#
|
||||
# CONFIG_SDIO_DMA
|
||||
# SDIO driver supports DMA
|
||||
# CONFIG_MMCSD_MMCSUPPORT
|
||||
# Enable support for MMC cards
|
||||
# CONFIG_MMCSD_HAVECARDDETECT
|
||||
# SDIO driver card detection is 100% accurate
|
||||
#
|
||||
CONFIG_SDIO_DMA=n
|
||||
CONFIG_MMCSD_MMCSUPPORT=n
|
||||
CONFIG_MMCSD_HAVECARDDETECT=n
|
||||
|
||||
#
|
||||
# TCP/IP and UDP support via uIP
|
||||
# CONFIG_NET - Enable or disable all network features
|
||||
# CONFIG_NET_IPv6 - Build in support for IPv6
|
||||
# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
|
||||
# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
|
||||
# CONFIG_NET_BUFSIZE - uIP buffer size
|
||||
# CONFIG_NET_TCP - TCP support on or off
|
||||
# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
|
||||
# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
|
||||
# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
|
||||
# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
|
||||
# accept() is called. The size of the backlog is selected when listen() is called.
|
||||
# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
|
||||
# CONFIG_NET_UDP - UDP support on or off
|
||||
# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
|
||||
# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
|
||||
# CONFIG_NET_ICMP - ICMP ping response support on or off
|
||||
# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
|
||||
# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
|
||||
# CONFIG_NET_STATISTICS - uIP statistics on or off
|
||||
# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
|
||||
# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
|
||||
# CONFIG_NET_BROADCAST - Broadcast support
|
||||
# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
|
||||
#
|
||||
CONFIG_NET=n
|
||||
CONFIG_NET_IPv6=n
|
||||
CONFIG_NSOCKET_DESCRIPTORS=0
|
||||
CONFIG_NET_SOCKOPTS=y
|
||||
CONFIG_NET_BUFSIZE=420
|
||||
CONFIG_NET_TCP=n
|
||||
CONFIG_NET_TCP_CONNS=40
|
||||
CONFIG_NET_MAX_LISTENPORTS=40
|
||||
CONFIG_NET_UDP=n
|
||||
CONFIG_NET_UDP_CHECKSUMS=y
|
||||
#CONFIG_NET_UDP_CONNS=10
|
||||
CONFIG_NET_ICMP=n
|
||||
CONFIG_NET_ICMP_PING=n
|
||||
#CONFIG_NET_PINGADDRCONF=0
|
||||
CONFIG_NET_STATISTICS=y
|
||||
#CONFIG_NET_RECEIVE_WINDOW=
|
||||
#CONFIG_NET_ARPTAB_SIZE=8
|
||||
CONFIG_NET_BROADCAST=n
|
||||
#CONFIG_NET_FWCACHE_SIZE=2
|
||||
|
||||
#
|
||||
# UIP Network Utilities
|
||||
# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
|
||||
# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
|
||||
#
|
||||
CONFIG_NET_DHCP_LIGHT=n
|
||||
CONFIG_NET_RESOLV_ENTRIES=4
|
||||
|
||||
#
|
||||
# USB Device Configuration
|
||||
#
|
||||
# CONFIG_USBDEV
|
||||
# Enables USB device support
|
||||
# CONFIG_USBDEV_ISOCHRONOUS
|
||||
# Build in extra support for isochronous endpoints
|
||||
# CONFIG_USBDEV_DUALSPEED
|
||||
# Hardware handles high and full speed operation (USB 2.0)
|
||||
# CONFIG_USBDEV_SELFPOWERED
|
||||
# Will cause USB features to indicate that the device is
|
||||
# self-powered
|
||||
# CONFIG_USBDEV_MAXPOWER
|
||||
# Maximum power consumption in mA
|
||||
# CONFIG_USBDEV_TRACE
|
||||
# Enables USB tracing for debug
|
||||
# CONFIG_USBDEV_TRACE_NRECORDS
|
||||
# Number of trace entries to remember
|
||||
#
|
||||
CONFIG_USBDEV=y
|
||||
CONFIG_USBDEV_ISOCHRONOUS=n
|
||||
CONFIG_USBDEV_DUALSPEED=n
|
||||
CONFIG_USBDEV_SELFPOWERED=y
|
||||
CONFIG_USBDEV_REMOTEWAKEUP=n
|
||||
CONFIG_USBDEV_MAXPOWER=100
|
||||
CONFIG_USBDEV_TRACE=n
|
||||
CONFIG_USBDEV_TRACE_NRECORDS=128
|
||||
|
||||
#
|
||||
# USB Serial Device Configuration (Prolific PL2303 Emulation)
|
||||
#
|
||||
# CONFIG_USBSER
|
||||
# Enable compilation of the USB serial driver
|
||||
# CONFIG_USBSER_EPINTIN
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# interrupt IN operation
|
||||
# CONFIG_USBSER_EPBULKOUT
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# bulk OUT operation
|
||||
# CONFIG_USBSER_EPBULKIN
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# bulk IN operation
|
||||
# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
|
||||
# The number of write/read requests that can be in flight
|
||||
# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
|
||||
# The vendor ID code/string
|
||||
# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
|
||||
# The product ID code/string
|
||||
# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
|
||||
# Size of the serial receive/transmit buffers
|
||||
#
|
||||
CONFIG_USBSER=y
|
||||
CONFIG_USBSER_EPINTIN=1
|
||||
CONFIG_USBSER_EPBULKOUT=2
|
||||
CONFIG_USBSER_EPBULKIN=3
|
||||
CONFIG_USBSER_NWRREQS=4
|
||||
CONFIG_USBSER_NRDREQS=4
|
||||
CONFIG_USBSER_VENDORID=0x067b
|
||||
CONFIG_USBSER_PRODUCTID=0x2303
|
||||
CONFIG_USBSER_VENDORSTR="Nuttx"
|
||||
CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
|
||||
CONFIG_USBSER_RXBUFSIZE=512
|
||||
CONFIG_USBSER_TXBUFSIZE=512
|
||||
|
||||
#
|
||||
# USB serial device class driver (Standard CDC ACM class)
|
||||
#
|
||||
# CONFIG_CDCSER
|
||||
# Enable compilation of the USB serial driver
|
||||
# CONFIG_CDCSER_EP0MAXPACKET
|
||||
# Endpoint 0 max packet size. Default 64
|
||||
# CONFIG_CDCSER_EPINTIN
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# interrupt IN operation. Default 2.
|
||||
# CONFIG_CDCSER_EPINTIN_FSSIZE
|
||||
# Max package size for the interrupt IN endpoint if full speed mode.
|
||||
# Default 64.
|
||||
# CONFIG_CDCSER_EPINTIN_HSSIZE
|
||||
# Max package size for the interrupt IN endpoint if high speed mode.
|
||||
# Default 64
|
||||
# CONFIG_CDCSER_EPBULKOUT
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# bulk OUT operation
|
||||
# CONFIG_CDCSER_EPBULKOUT_FSSIZE
|
||||
# Max package size for the bulk OUT endpoint if full speed mode.
|
||||
# Default 64.
|
||||
# CONFIG_CDCSER_EPBULKOUT_HSSIZE
|
||||
# Max package size for the bulk OUT endpoint if high speed mode.
|
||||
# Default 512.
|
||||
# CONFIG_CDCSER_EPBULKIN
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# bulk IN operation
|
||||
# CONFIG_CDCSER_EPBULKIN_FSSIZE
|
||||
# Max package size for the bulk IN endpoint if full speed mode.
|
||||
# Default 64.
|
||||
# CONFIG_CDCSER_EPBULKIN_HSSIZE
|
||||
# Max package size for the bulk IN endpoint if high speed mode.
|
||||
# Default 512.
|
||||
# CONFIG_CDCSER_NWRREQS and CONFIG_CDCSER_NRDREQS
|
||||
# The number of write/read requests that can be in flight.
|
||||
# Default 256.
|
||||
# CONFIG_CDCSER_VENDORID and CONFIG_CDCSER_VENDORSTR
|
||||
# The vendor ID code/string. Default 0x0525 and "NuttX"
|
||||
# 0x0525 is the Netchip vendor and should not be used in any
|
||||
# products. This default VID was selected for compatibility with
|
||||
# the Linux CDC ACM default VID.
|
||||
# CONFIG_CDCSER_PRODUCTID and CONFIG_CDCSER_PRODUCTSTR
|
||||
# The product ID code/string. Default 0xara7 and "CDC/ACM Serial"
|
||||
# 0xa4a7 was selected for compatibility with the Linux CDC ACM
|
||||
# default PID.
|
||||
# CONFIG_CDCSER_RXBUFSIZE and CONFIG_CDCSER_TXBUFSIZE
|
||||
# Size of the serial receive/transmit buffers. Default 256.
|
||||
#
|
||||
CONFIG_CDCSER=n
|
||||
#CONFIG_CDCSER_EP0MAXPACKET
|
||||
#CONFIG_CDCSER_EPINTIN
|
||||
#CONFIG_CDCSER_EPINTIN_FSSIZE
|
||||
#CONFIG_CDCSER_EPINTIN_HSSIZE
|
||||
#CONFIG_CDCSER_EPBULKOUT
|
||||
#CONFIG_CDCSER_EPBULKOUT_FSSIZE
|
||||
#CONFIG_CDCSER_EPBULKOUT_HSSIZE
|
||||
#CONFIG_CDCSER_EPBULKIN
|
||||
#CONFIG_CDCSER_EPBULKIN_FSSIZE
|
||||
#CONFIG_CDCSER_EPBULKIN_HSSIZE
|
||||
#CONFIG_CDCSER_NWRREQS
|
||||
#CONFIG_CDCSER_NRDREQS
|
||||
#CONFIG_CDCSER_VENDORID
|
||||
#CONFIG_CDCSER_VENDORSTR
|
||||
#CONFIG_CDCSER_PRODUCTID
|
||||
#CONFIG_CDCSER_PRODUCTSTR
|
||||
#CONFIG_CDCSER_RXBUFSIZE
|
||||
#CONFIG_CDCSER_TXBUFSIZE
|
||||
|
||||
# USB Storage Device Configuration
|
||||
#
|
||||
# CONFIG_USBSTRG
|
||||
# Enable compilation of the USB storage driver
|
||||
# CONFIG_USBSTRG_EP0MAXPACKET
|
||||
# Max packet size for endpoint 0
|
||||
# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
|
||||
# The logical 7-bit address of a hardware endpoints that support
|
||||
# bulk OUT and IN operations
|
||||
# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
|
||||
# The number of write/read requests that can be in flight
|
||||
# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
|
||||
# The size of the buffer in each write/read request. This
|
||||
# value needs to be at least as large as the endpoint
|
||||
# maxpacket and ideally as large as a block device sector.
|
||||
# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
|
||||
# The vendor ID code/string
|
||||
# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
|
||||
# The product ID code/string
|
||||
# CONFIG_USBSTRG_REMOVABLE
|
||||
# Select if the media is removable
|
||||
#
|
||||
CONFIG_USBSTRG=n
|
||||
CONFIG_USBSTRG_EP0MAXPACKET=64
|
||||
CONFIG_USBSTRG_EPBULKOUT=2
|
||||
CONFIG_USBSTRG_EPBULKIN=5
|
||||
CONFIG_USBSTRG_NRDREQS=2
|
||||
CONFIG_USBSTRG_NWRREQS=2
|
||||
CONFIG_USBSTRG_BULKINREQLEN=256
|
||||
CONFIG_USBSTRG_BULKOUTREQLEN=256
|
||||
CONFIG_USBSTRG_VENDORID=0x584e
|
||||
CONFIG_USBSTRG_VENDORSTR="NuttX"
|
||||
CONFIG_USBSTRG_PRODUCTID=0x5342
|
||||
CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
|
||||
CONFIG_USBSTRG_VERSIONNO=0x0399
|
||||
CONFIG_USBSTRG_REMOVABLE=y
|
||||
|
||||
#
|
||||
# Settings for examples/uip
|
||||
#
|
||||
CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_UIP_DHCPC=n
|
||||
|
||||
#
|
||||
# Settings for examples/nettest
|
||||
CONFIG_EXAMPLE_NETTEST_SERVER=n
|
||||
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
|
||||
CONFIG_EXAMPLE_NETTEST_NOMAC=n
|
||||
CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
|
||||
|
||||
#
|
||||
# Settings for examples/ostest
|
||||
#
|
||||
CONFIG_EXAMPLES_OSTEST_LOOPS=1
|
||||
CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
|
||||
CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
|
||||
|
||||
#
|
||||
# Settings for apps/nshlib
|
||||
#
|
||||
# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
|
||||
# CONFIG_NSH_STRERROR - Use strerror(errno)
|
||||
# CONFIG_NSH_LINELEN - Maximum length of one command line
|
||||
# CONFIG_NSH_STACKSIZE - Stack size to use for new threads.
|
||||
# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
|
||||
# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
|
||||
# CONFIG_NSH_DISABLEBG - Disable background commands
|
||||
# CONFIG_NSH_ROMFSETC - Use startup script in /etc
|
||||
# CONFIG_NSH_CONSOLE - Use serial console front end
|
||||
# CONFIG_NSH_TELNET - Use telnetd console front end
|
||||
# CONFIG_NSH_ARCHINIT - Platform provides architecture
|
||||
# specific initialization (nsh_archinitialize()).
|
||||
#
|
||||
# If CONFIG_NSH_TELNET is selected:
|
||||
# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
|
||||
# CONFIG_NSH_DHCPC - Obtain address using DHCP
|
||||
# CONFIG_NSH_IPADDR - Provides static IP address
|
||||
# CONFIG_NSH_DRIPADDR - Provides static router IP address
|
||||
# CONFIG_NSH_NETMASK - Provides static network mask
|
||||
# CONFIG_NSH_NOMAC - Use a bogus MAC address
|
||||
#
|
||||
# If CONFIG_NSH_ROMFSETC is selected:
|
||||
# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
|
||||
# CONFIG_NSH_INITSCRIPT - Relative path to init script
|
||||
# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
|
||||
# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
|
||||
# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
|
||||
# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
|
||||
# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
|
||||
# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
|
||||
#
|
||||
CONFIG_NSH_FILEIOSIZE=512
|
||||
CONFIG_NSH_STRERROR=n
|
||||
CONFIG_NSH_LINELEN=64
|
||||
CONFIG_NSH_STACKSIZE=2048
|
||||
CONFIG_NSH_NESTDEPTH=3
|
||||
CONFIG_NSH_DISABLESCRIPT=n
|
||||
CONFIG_NSH_DISABLEBG=n
|
||||
CONFIG_NSH_ROMFSETC=n
|
||||
CONFIG_NSH_CONSOLE=y
|
||||
CONFIG_NSH_TELNET=n
|
||||
CONFIG_NSH_ARCHINIT=n
|
||||
CONFIG_NSH_IOBUFFER_SIZE=512
|
||||
CONFIG_NSH_DHCPC=n
|
||||
CONFIG_NSH_NOMAC=n
|
||||
CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_NSH_ROMFSMOUNTPT="/etc"
|
||||
CONFIG_NSH_INITSCRIPT="init.d/rcS"
|
||||
CONFIG_NSH_ROMFSDEVNO=0
|
||||
CONFIG_NSH_ROMFSSECTSIZE=64
|
||||
CONFIG_NSH_FATDEVNO=1
|
||||
CONFIG_NSH_FATSECTSIZE=512
|
||||
CONFIG_NSH_FATNSECTORS=1024
|
||||
CONFIG_NSH_FATMOUNTPT=/tmp
|
||||
|
||||
#
|
||||
# Architecture-specific NSH options
|
||||
#
|
||||
CONFIG_NSH_MMCSDSPIPORTNO=0
|
||||
CONFIG_NSH_MMCSDSLOTNO=0
|
||||
CONFIG_NSH_MMCSDMINOR=0
|
||||
|
||||
#
|
||||
# Settings for examples/usbserial
|
||||
#
|
||||
# CONFIG_EXAMPLES_USBSERIAL_INONLY
|
||||
# Only verify IN (device-to-host) data transfers. Default: both
|
||||
# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
|
||||
# Only verify OUT (host-to-device) data transfers. Default: both
|
||||
# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
|
||||
# Send only small, single packet messages. Default: Send large and small.
|
||||
# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
|
||||
# Send only large, multi-packet messages. Default: Send large and small.
|
||||
#
|
||||
CONFIG_EXAMPLES_USBSERIAL_INONLY=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
|
||||
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
|
||||
|
||||
#
|
||||
# Settings for examples/usbterm
|
||||
#
|
||||
# CONFIG_EXAMPLES_UBSTERM_BUILTIN - Build the usbterm example as an NSH
|
||||
# built-in command. NOTE: This is not fully functional as of this
|
||||
# writing.. It should work, but there is no mechanism in place yet
|
||||
# to exit the USB terminal program and return to NSH.
|
||||
# CONFIG_EXAMPLES_USBTERM_BUFLEN - The size of the input and output
|
||||
# buffers used for receiving data. Default 256 bytes.
|
||||
#
|
||||
# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB, or
|
||||
# CONFIG_USBDEV_TRACE), then the example code will also manage the USB trace
|
||||
# output. The amount of trace output can be controlled using:
|
||||
#
|
||||
# CONFIG_EXAMPLES_USBTERM_TRACEINIT - Show initialization events
|
||||
# CONFIG_EXAMPLES_USBTERM_TRACECLASS - Show class driver events
|
||||
# CONFIG_EXAMPLES_USBTERM_TRACETRANSFERS - Show data transfer events
|
||||
# CONFIG_EXAMPLES_USBTERM_TRACECONTROLLER - Show controller events
|
||||
# CONFIG_EXAMPLES_USBTERM_TRACEINTERRUPTS - Show interrupt-related events
|
||||
#
|
||||
CONFIG_EXAMPLES_UBSTERM_BUILTIN=n
|
||||
CONFIG_EXAMPLES_USBTERM_BUFLEN=256
|
||||
CONFIG_EXAMPLES_USBTERM_TRACEINIT=n
|
||||
CONFIG_EXAMPLES_USBTERM_TRACECLASS=n
|
||||
CONFIG_EXAMPLES_USBTERM_TRACETRANSFERS=n
|
||||
CONFIG_EXAMPLES_USBTERM_TRACECONTROLLER=n
|
||||
CONFIG_EXAMPLES_USBTERM_TRACEINTERRUPTS=n
|
||||
|
||||
#
|
||||
# Stack and heap information
|
||||
#
|
||||
# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
|
||||
# operation from FLASH but must copy initialized .data sections to RAM.
|
||||
# (should also be =n for the Hy-Mini STM32v which always runs from flash)
|
||||
# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH
|
||||
# but copy themselves entirely into RAM for better performance.
|
||||
# CONFIG_CUSTOM_STACK - The up_ implementation will handle
|
||||
# all stack operations outside of the nuttx model.
|
||||
# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
|
||||
# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
|
||||
# This is the thread that (1) performs the inital boot of the system up
|
||||
# to the point where user_start() is spawned, and (2) there after is the
|
||||
# IDLE thread that executes only when there is no other thread ready to
|
||||
# run.
|
||||
# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
|
||||
# for the main user thread that begins at the user_start() entry point.
|
||||
# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
|
||||
# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
|
||||
# CONFIG_HEAP_BASE - The beginning of the heap
|
||||
# CONFIG_HEAP_SIZE - The size of the heap
|
||||
#
|
||||
CONFIG_BOOT_RUNFROMFLASH=n
|
||||
CONFIG_BOOT_COPYTORAM=n
|
||||
CONFIG_CUSTOM_STACK=n
|
||||
CONFIG_STACK_POINTER=
|
||||
CONFIG_IDLETHREAD_STACKSIZE=1024
|
||||
CONFIG_USERMAIN_STACKSIZE=2048
|
||||
CONFIG_PTHREAD_STACK_MIN=256
|
||||
CONFIG_PTHREAD_STACK_DEFAULT=2048
|
||||
CONFIG_HEAP_BASE=
|
||||
CONFIG_HEAP_SIZE=
|
|
@ -0,0 +1,113 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/usbserial/ld.script
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
* Laurent Latil <laurent@latil.nom.fr>
|
||||
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F103VCT6 has 256Kb of FLASH beginning at address 0x0800:0000 and
|
||||
* 48Kb of SRAM beginning at address 0x2000:0000. When booting from FLASH,
|
||||
* FLASH memory is aliased to address 0x0000:0000 where the code expects to
|
||||
* begin execution by jumping to the entry point in the 0x0800:0000 address
|
||||
* range.
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x08000000, LENGTH = 256K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 48K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} >sram
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
|
@ -0,0 +1,111 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/usbserial/ld.script.dfu
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
|
||||
* 64Kb of SRAM beginning at address 0x2000:0000. Here we assume that the
|
||||
* Hy-Mini STM32v's DFU bootloader is being used. In that case, the corrct
|
||||
* load .text load address is 0x08003000 (leaving 464Kb).
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x08003000, LENGTH = 464K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} >sram
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
|
@ -0,0 +1,47 @@
|
|||
#!/bin/bash
|
||||
# configs/hymini-stm32v/ostest/setenv.sh
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
|
||||
if [ "$(basename $0)" = "setenv.sh" ] ; then
|
||||
echo "You must source this script, not run it!" 1>&2
|
||||
exit 1
|
||||
fi
|
||||
|
||||
if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi
|
||||
|
||||
WD=`pwd`
|
||||
export RIDE_BIN="/cygdrive/c/Program Files/Raisonance/Ride/arm-gcc/bin"
|
||||
export BUILDROOT_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
|
||||
export PATH="${BUILDROOT_BIN}:${RIDE_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
|
||||
|
||||
echo "PATH : ${PATH}"
|
|
@ -0,0 +1,174 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/usbstorage/Make.defs
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include ${TOPDIR}/.config
|
||||
|
||||
# Setup for the selected toolchain
|
||||
|
||||
ifeq ($(CONFIG_STM32_DFU),y)
|
||||
LDSCRIPT = ld.script.dfu
|
||||
else
|
||||
LDSCRIPT = ld.script
|
||||
endif
|
||||
|
||||
ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
|
||||
# CodeSourcery under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
|
||||
# CodeSourcery under Linux
|
||||
CROSSDEV = arm-none-eabi-
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -O2
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_DEVKITARM),y)
|
||||
# devkitARM under Windows
|
||||
CROSSDEV = arm-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_RAISONANCE),y)
|
||||
# Raisonance RIDE7 under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_STM32_BUILDROOT),y)
|
||||
# NuttX buildroot under Linux or Cygwin
|
||||
CROSSDEV = arm-elf-
|
||||
ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -Os
|
||||
endif
|
||||
|
||||
ifeq ($(WINTOOL),y)
|
||||
# Windows-native toolchains
|
||||
DIRLINK = $(TOPDIR)/tools/winlink.sh
|
||||
DIRUNLINK = $(TOPDIR)/tools/unlink.sh
|
||||
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
|
||||
ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/usbstorage/$(LDSCRIPT)}"
|
||||
MAXOPTIMIZATION = -O2
|
||||
else
|
||||
# Linux/Cygwin-native toolchain
|
||||
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
||||
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
||||
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/usbstorage/$(LDSCRIPT)
|
||||
endif
|
||||
|
||||
CC = $(CROSSDEV)gcc
|
||||
CXX = $(CROSSDEV)g++
|
||||
CPP = $(CROSSDEV)gcc -E
|
||||
LD = $(CROSSDEV)ld
|
||||
AR = $(CROSSDEV)ar rcs
|
||||
NM = $(CROSSDEV)nm
|
||||
OBJCOPY = $(CROSSDEV)objcopy
|
||||
OBJDUMP = $(CROSSDEV)objdump
|
||||
|
||||
ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
|
||||
ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
|
||||
|
||||
ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
|
||||
ARCHOPTIMIZATION = -g
|
||||
else
|
||||
ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
|
||||
endif
|
||||
|
||||
ARCHCFLAGS = -fno-builtin
|
||||
ARCHCXXFLAGS = -fno-builtin -fno-exceptions
|
||||
ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
|
||||
ARCHWARNINGSXX = -Wall -Wshadow
|
||||
ARCHDEFINES =
|
||||
ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
|
||||
|
||||
CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
|
||||
CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
|
||||
CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
|
||||
AFLAGS = $(CFLAGS) -D__ASSEMBLY__
|
||||
|
||||
NXFLATLDFLAGS1 = -r -d -warn-common
|
||||
NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
|
||||
LDNXFLATFLAGS = -e main -s 2048
|
||||
|
||||
OBJEXT = .o
|
||||
LIBEXT = .a
|
||||
EXEEXT =
|
||||
|
||||
ifneq ($(CROSSDEV),arm-elf-)
|
||||
LDFLAGS += -nostartfiles -nodefaultlibs
|
||||
endif
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
LDFLAGS += -g
|
||||
endif
|
||||
|
||||
define PREPROCESS
|
||||
@echo "CPP: $1->$2"
|
||||
@$(CPP) $(CPPFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILE
|
||||
@echo "CC: $1"
|
||||
@$(CC) -c $(CFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILEXX
|
||||
@echo "CXX: $1"
|
||||
@$(CXX) -c $(CXXFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ASSEMBLE
|
||||
@echo "AS: $1"
|
||||
@$(CC) -c $(AFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ARCHIVE
|
||||
echo "AR: $2"; \
|
||||
$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
|
||||
endef
|
||||
|
||||
define CLEAN
|
||||
@rm -f *.o *.a
|
||||
endef
|
||||
|
||||
HOSTCC = gcc
|
||||
HOSTINCLUDES = -I.
|
||||
HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
|
||||
HOSTLDFLAGS =
|
||||
|
|
@ -0,0 +1,39 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/usbstorage/appconfig
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
# Path to example in apps/examples containing the user_start entry point
|
||||
|
||||
CONFIGURED_APPS += examples/usbstorage
|
||||
|
|
@ -0,0 +1,928 @@
|
|||
############################################################################
|
||||
# configs/hymini-stm32v/usbstorage/defconfig
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
#
|
||||
# architecture selection
|
||||
#
|
||||
# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
|
||||
# processor architecture.
|
||||
# CONFIG_ARCH_family - for use in C code. This identifies the
|
||||
# particular chip family that the architecture is implemented
|
||||
# in.
|
||||
# CONFIG_ARCH_architecture - for use in C code. This identifies the
|
||||
# specific architecture within the chip familyl.
|
||||
# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||||
# CONFIG_ARCH_CHIP_name - For use in C code
|
||||
# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
|
||||
# the board that supports the particular chip or SoC.
|
||||
# CONFIG_ARCH_BOARD_name - for use in C code
|
||||
# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
|
||||
# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
|
||||
# CONFIG_DRAM_SIZE - Describes the installed DRAM.
|
||||
# CONFIG_DRAM_START - The start address of DRAM (physical)
|
||||
# CONFIG_DRAM_END - Last address+1 of installed RAM
|
||||
# CONFIG_ARCH_IRQPRIO - The ST32F103Z supports interrupt prioritization
|
||||
# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
||||
# stack. If defined, this symbol is the size of the interrupt
|
||||
# stack in bytes. If not defined, the user task stacks will be
|
||||
# used during interrupt handling.
|
||||
# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||||
# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
|
||||
# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
||||
# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture.
|
||||
# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
||||
# cause a 100 second delay during boot-up. This 100 second delay
|
||||
# serves no purpose other than it allows you to calibrate
|
||||
# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure
|
||||
# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
|
||||
# the delay actually is 100 seconds.
|
||||
# CONFIG_ARCH_DMA - Support DMA initialization
|
||||
#
|
||||
CONFIG_ARCH=arm
|
||||
CONFIG_ARCH_ARM=y
|
||||
CONFIG_ARCH_CORTEXM3=y
|
||||
CONFIG_ARCH_CHIP=stm32
|
||||
CONFIG_ARCH_CHIP_STM32F103VCT6=y
|
||||
CONFIG_ARCH_BOARD=hymini-stm32v
|
||||
CONFIG_ARCH_BOARD_HYMINI_STM32V=y
|
||||
|
||||
CONFIG_BOARD_LOOPSPERMSEC=5483
|
||||
CONFIG_DRAM_SIZE=0x0000C000
|
||||
CONFIG_DRAM_START=0x20000000
|
||||
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
||||
CONFIG_ARCH_IRQPRIO=y
|
||||
CONFIG_ARCH_INTERRUPTSTACK=n
|
||||
CONFIG_ARCH_STACKDUMP=y
|
||||
CONFIG_ARCH_BOOTLOADER=n
|
||||
CONFIG_ARCH_LEDS=y
|
||||
CONFIG_ARCH_BUTTONS=n
|
||||
CONFIG_ARCH_CALIBRATION=n
|
||||
CONFIG_ARCH_DMA=y
|
||||
|
||||
#
|
||||
# Identify toolchain and linker options
|
||||
#
|
||||
CONFIG_STM32_CODESOURCERYW=n
|
||||
CONFIG_STM32_CODESOURCERYL=y
|
||||
CONFIG_STM32_DEVKITARM=n
|
||||
CONFIG_STM32_RAISONANCE=n
|
||||
CONFIG_STM32_BUILDROOT=n
|
||||
CONFIG_STM32_DFU=n
|
||||
|
||||
#
|
||||
# Individual subsystems can be enabled:
|
||||
# AHB:
|
||||
CONFIG_STM32_DMA1=n
|
||||
CONFIG_STM32_DMA2=y
|
||||
CONFIG_STM32_CRC=n
|
||||
CONFIG_STM32_FSMC=y
|
||||
CONFIG_STM32_SDIO=y
|
||||
# APB1:
|
||||
CONFIG_STM32_TIM2=n
|
||||
CONFIG_STM32_TIM3=n
|
||||
CONFIG_STM32_TIM4=n
|
||||
CONFIG_STM32_TIM5=n
|
||||
CONFIG_STM32_TIM6=n
|
||||
CONFIG_STM32_TIM7=n
|
||||
CONFIG_STM32_WWDG=n
|
||||
CONFIG_STM32_SPI2=n
|
||||
CONFIG_STM32_SPI4=n
|
||||
CONFIG_STM32_USART2=y
|
||||
CONFIG_STM32_USART3=n
|
||||
CONFIG_STM32_UART4=n
|
||||
CONFIG_STM32_UART5=n
|
||||
CONFIG_STM32_I2C1=n
|
||||
CONFIG_STM32_I2C2=n
|
||||
CONFIG_STM32_USB=y
|
||||
CONFIG_STM32_CAN=n
|
||||
CONFIG_STM32_BKP=n
|
||||
CONFIG_STM32_PWR=n
|
||||
CONFIG_STM32_DAC=n
|
||||
# APB2:
|
||||
CONFIG_STM32_ADC1=n
|
||||
CONFIG_STM32_ADC2=n
|
||||
CONFIG_STM32_TIM1=n
|
||||
CONFIG_STM32_SPI1=n
|
||||
CONFIG_STM32_TIM8=n
|
||||
CONFIG_STM32_USART1=y
|
||||
CONFIG_STM32_ADC3=n
|
||||
|
||||
#
|
||||
# Timer and I2C devices may need to the following to force power to be applied:
|
||||
#
|
||||
#CONFIG_STM32_FORCEPOWER=y
|
||||
|
||||
#
|
||||
# STM32F103V specific serial device driver settings
|
||||
#
|
||||
# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
|
||||
# console and ttys0 (default is the USART1).
|
||||
# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
|
||||
# This specific the size of the receive buffer
|
||||
# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
|
||||
# being sent. This specific the size of the transmit buffer
|
||||
# CONFIG_USARTn_BAUD - The configure BAUD of the UART. Must be
|
||||
# CONFIG_USARTn_BITS - The number of bits. Must be either 7 or 8.
|
||||
# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
||||
# CONFIG_USARTn_2STOP - Two stop bits
|
||||
#
|
||||
CONFIG_USART1_SERIAL_CONSOLE=y
|
||||
CONFIG_USART2_SERIAL_CONSOLE=n
|
||||
CONFIG_USART3_SERIAL_CONSOLE=n
|
||||
CONFIG_USART4_SERIAL_CONSOLE=n
|
||||
CONFIG_USART5_SERIAL_CONSOLE=n
|
||||
|
||||
CONFIG_USART1_TXBUFSIZE=256
|
||||
CONFIG_USART2_TXBUFSIZE=256
|
||||
CONFIG_USART3_TXBUFSIZE=256
|
||||
CONFIG_USART4_TXBUFSIZE=256
|
||||
CONFIG_USART5_TXBUFSIZE=256
|
||||
|
||||
CONFIG_USART1_RXBUFSIZE=256
|
||||
CONFIG_USART2_RXBUFSIZE=256
|
||||
CONFIG_USART3_RXBUFSIZE=256
|
||||
CONFIG_USART4_RXBUFSIZE=256
|
||||
CONFIG_USART5_RXBUFSIZE=256
|
||||
|
||||
CONFIG_USART1_BAUD=115200
|
||||
CONFIG_USART2_BAUD=115200
|
||||
CONFIG_USART3_BAUD=115200
|
||||
CONFIG_USART4_BAUD=115200
|
||||
CONFIG_USART5_BAUD=115200
|
||||
|
||||
CONFIG_USART1_BITS=8
|
||||
CONFIG_USART2_BITS=8
|
||||
CONFIG_USART3_BITS=8
|
||||
CONFIG_USART4_BITS=8
|
||||
CONFIG_USART5_BITS=8
|
||||
|
||||
CONFIG_USART1_PARITY=0
|
||||
CONFIG_USART2_PARITY=0
|
||||
CONFIG_USART3_PARITY=0
|
||||
CONFIG_USART4_PARITY=0
|
||||
CONFIG_USART5_PARITY=0
|
||||
|
||||
CONFIG_USART1_2STOP=0
|
||||
CONFIG_USART2_2STOP=0
|
||||
CONFIG_USART3_2STOP=0
|
||||
CONFIG_USART4_2STOP=0
|
||||
CONFIG_USART5_2STOP=0
|
||||
|
||||
#
|
||||
# STM32F103V specific SSI device driver settings
|
||||
#
|
||||
# CONFIG_SSIn_DISABLE - select to disable all support for
|
||||
# the SSI
|
||||
# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
|
||||
# Poll-waiting is recommended if the interrupt rate would be to
|
||||
# high in the interrupt driven case.
|
||||
# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
|
||||
# emptying the Rx FIFO. If the SPI frequency is high and this
|
||||
# value is large, then larger values of this setting may cause
|
||||
# Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
|
||||
#
|
||||
CONFIG_SSI0_DISABLE=n
|
||||
CONFIG_SSI1_DISABLE=y
|
||||
CONFIG_SSI_POLLWAIT=y
|
||||
#CONFIG_SSI_TXLIMIT=4
|
||||
|
||||
#
|
||||
# General build options
|
||||
#
|
||||
# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
|
||||
# BSPs from www.ridgerun.com using the tools/mkimage.sh script
|
||||
# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_RAW_BINARY - make a raw binary format file used with many
|
||||
# different loaders using the GNU objcopy program. This option
|
||||
# should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_HAVE_LIBM - toolchain supports libm.a
|
||||
#
|
||||
CONFIG_RRLOAD_BINARY=n
|
||||
CONFIG_INTELHEX_BINARY=n
|
||||
CONFIG_MOTOROLA_SREC=n
|
||||
CONFIG_RAW_BINARY=y
|
||||
CONFIG_HAVE_LIBM=n
|
||||
|
||||
#
|
||||
# General OS setup
|
||||
#
|
||||
# CONFIG_APPS_DIR - Identifies the relative path to the directory
|
||||
# that builds the application to link with NuttX. Default: ../apps
|
||||
# CONFIG_DEBUG - enables built-in debug options
|
||||
# CONFIG_DEBUG_VERBOSE - enables verbose debug output
|
||||
# CONFIG_DEBUG_SYMBOLS - build without optimization and with
|
||||
# debug symbols (needed for use with a debugger).
|
||||
# CONFIG_MM_REGIONS - If the architecture includes multiple
|
||||
# regions of memory to allocate from, this specifies the
|
||||
# number of memory regions that the memory manager must
|
||||
# handle and enables the API mm_addregion(start, end);
|
||||
# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
|
||||
# time console output
|
||||
# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
|
||||
# or MSEC_PER_TICK=10. This setting may be defined to
|
||||
# inform NuttX that the processor hardware is providing
|
||||
# system timer interrupts at some interrupt interval other
|
||||
# than 10 msec.
|
||||
# CONFIG_RR_INTERVAL - The round robin timeslice will be set
|
||||
# this number of milliseconds; Round robin scheduling can
|
||||
# be disabled by setting this value to zero.
|
||||
# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in
|
||||
# scheduler to monitor system performance
|
||||
# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
|
||||
# task name to save in the TCB. Useful if scheduler
|
||||
# instrumentation is selected. Set to zero to disable.
|
||||
# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
|
||||
# Used to initialize the internal time logic.
|
||||
# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
|
||||
# You would only need this if you are concerned about accurate
|
||||
# time conversions in the past or in the distant future.
|
||||
# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
|
||||
# would only need this if you are concerned about accurate
|
||||
# time conversion in the distand past. You must also define
|
||||
# CONFIG_GREGORIAN_TIME in order to use Julian time.
|
||||
# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
|
||||
# provides /dev/console. Enables stdout, stderr, stdin.
|
||||
# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
|
||||
# driver (minimul support)
|
||||
# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
|
||||
# errorcheck mutexes. Enables pthread_mutexattr_settype().
|
||||
# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
|
||||
# inheritance on mutexes and semaphores.
|
||||
# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
|
||||
# inheritance is enabled. It defines the maximum number of
|
||||
# different threads (minus one) that can take counts on a
|
||||
# semaphore with priority inheritance support. This may be
|
||||
# set to zero if priority inheritance is disabled OR if you
|
||||
# are only using semaphores as mutexes (only one holder) OR
|
||||
# if no more than two threads participate using a counting
|
||||
# semaphore.
|
||||
# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled,
|
||||
# then this setting is the maximum number of higher priority
|
||||
# threads (minus 1) than can be waiting for another thread
|
||||
# to release a count on a semaphore. This value may be set
|
||||
# to zero if no more than one thread is expected to wait for
|
||||
# a semaphore.
|
||||
# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
|
||||
# by task_create() when a new task is started. If set, all
|
||||
# files/drivers will appear to be closed in the new task.
|
||||
# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
|
||||
# three file descriptors (stdin, stdout, stderr) by task_create()
|
||||
# when a new task is started. If set, all files/drivers will
|
||||
# appear to be closed in the new task except for stdin, stdout,
|
||||
# and stderr.
|
||||
# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
|
||||
# desciptors by task_create() when a new task is started. If
|
||||
# set, all sockets will appear to be closed in the new task.
|
||||
# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to
|
||||
# handle delayed processing from interrupt handlers. This feature
|
||||
# is required for some drivers but, if there are not complaints,
|
||||
# can be safely disabled. The worker thread also performs
|
||||
# garbage collection -- completing any delayed memory deallocations
|
||||
# from interrupt handlers. If the worker thread is disabled,
|
||||
# then that clean will be performed by the IDLE thread instead
|
||||
# (which runs at the lowest of priority and may not be appropriate
|
||||
# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE
|
||||
# is enabled, then the following options can also be used:
|
||||
# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
|
||||
# thread. Default: 50
|
||||
# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
|
||||
# work in units of microseconds. Default: 50*1000 (50 MS).
|
||||
# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
|
||||
# thread. Default: CONFIG_IDLETHREAD_STACKSIZE.
|
||||
# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
|
||||
# the worker thread. Default: 4
|
||||
#
|
||||
#CONFIG_APPS_DIR=
|
||||
CONFIG_DEBUG=n
|
||||
CONFIG_DEBUG_VERBOSE=n
|
||||
CONFIG_DEBUG_FS=n
|
||||
CONFIG_DEBUG_USB=n
|
||||
CONFIG_DEBUG_SYMBOLS=n
|
||||
CONFIG_MM_REGIONS=1
|
||||
CONFIG_ARCH_LOWPUTC=y
|
||||
CONFIG_RR_INTERVAL=200
|
||||
CONFIG_SCHED_INSTRUMENTATION=n
|
||||
CONFIG_TASK_NAME_SIZE=0
|
||||
CONFIG_START_YEAR=2009
|
||||
CONFIG_START_MONTH=11
|
||||
CONFIG_START_DAY=30
|
||||
CONFIG_GREGORIAN_TIME=n
|
||||
CONFIG_JULIAN_TIME=n
|
||||
CONFIG_DEV_CONSOLE=y
|
||||
CONFIG_DEV_LOWCONSOLE=n
|
||||
CONFIG_MUTEX_TYPES=n
|
||||
CONFIG_PRIORITY_INHERITANCE=n
|
||||
CONFIG_SEM_PREALLOCHOLDERS=0
|
||||
CONFIG_SEM_NNESTPRIO=0
|
||||
CONFIG_FDCLONE_DISABLE=n
|
||||
CONFIG_FDCLONE_STDIO=n
|
||||
CONFIG_SDCLONE_DISABLE=y
|
||||
CONFIG_SCHED_WORKQUEUE=y
|
||||
CONFIG_SCHED_WORKPRIORITY=50
|
||||
CONFIG_SCHED_WORKPERIOD=(50*1000)
|
||||
CONFIG_SCHED_WORKSTACKSIZE=1024
|
||||
CONFIG_SIG_SIGWORK=4
|
||||
|
||||
#
|
||||
# Settings for NXFLAT
|
||||
#
|
||||
# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
|
||||
# This format will support execution of NuttX binaries located
|
||||
# in a ROMFS filesystem (see examples/nxflat).
|
||||
# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals
|
||||
# with. CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and
|
||||
# CONFIG_DEBUG_BINFMT have to be defined or
|
||||
# CONFIG_NXFLAT_DUMPBUFFER does nothing.
|
||||
# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table
|
||||
# is ordered by symbol name
|
||||
#
|
||||
CONFIG_NXFLAT=n
|
||||
CONFIG_NXFLAT_DUMPBUFFER=n
|
||||
CONFIG_SYMTAB_ORDEREDBYNAME=y
|
||||
|
||||
#
|
||||
# The following can be used to disable categories of
|
||||
# APIs supported by the OS. If the compiler supports
|
||||
# weak functions, then it should not be necessary to
|
||||
# disable functions unless you want to restrict usage
|
||||
# of those APIs.
|
||||
#
|
||||
# There are certain dependency relationships in these
|
||||
# features.
|
||||
#
|
||||
# o mq_notify logic depends on signals to awaken tasks
|
||||
# waiting for queues to become full or empty.
|
||||
# o pthread_condtimedwait() depends on signals to wake
|
||||
# up waiting tasks.
|
||||
#
|
||||
CONFIG_DISABLE_CLOCK=n
|
||||
CONFIG_DISABLE_POSIX_TIMERS=n
|
||||
CONFIG_DISABLE_PTHREAD=n
|
||||
CONFIG_DISABLE_SIGNALS=n
|
||||
CONFIG_DISABLE_MQUEUE=n
|
||||
CONFIG_DISABLE_MOUNTPOINT=y
|
||||
CONFIG_DISABLE_ENVIRON=n
|
||||
CONFIG_DISABLE_POLL=y
|
||||
|
||||
#
|
||||
# Misc libc settings
|
||||
#
|
||||
# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
|
||||
# little smaller if we do not support fieldwidthes
|
||||
#
|
||||
CONFIG_NOPRINTF_FIELDWIDTH=n
|
||||
|
||||
#
|
||||
# Allow for architecture optimized implementations
|
||||
#
|
||||
# The architecture can provide optimized versions of the
|
||||
# following to improve system performance
|
||||
#
|
||||
CONFIG_ARCH_MEMCPY=n
|
||||
CONFIG_ARCH_MEMCMP=n
|
||||
CONFIG_ARCH_MEMMOVE=n
|
||||
CONFIG_ARCH_MEMSET=n
|
||||
CONFIG_ARCH_STRCMP=n
|
||||
CONFIG_ARCH_STRCPY=n
|
||||
CONFIG_ARCH_STRNCPY=n
|
||||
CONFIG_ARCH_STRLEN=n
|
||||
CONFIG_ARCH_STRNLEN=n
|
||||
CONFIG_ARCH_BZERO=n
|
||||
|
||||
#
|
||||
# Sizes of configurable things (0 disables)
|
||||
#
|
||||
# CONFIG_MAX_TASKS - The maximum number of simultaneously
|
||||
# active tasks. This value must be a power of two.
|
||||
# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
|
||||
# of parameters that a task may receive (i.e., maxmum value
|
||||
# of 'argc')
|
||||
# CONFIG_NPTHREAD_KEYS - The number of items of thread-
|
||||
# specific data that can be retained
|
||||
# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
|
||||
# descriptors (one for each open)
|
||||
# CONFIG_NFILE_STREAMS - The maximum number of streams that
|
||||
# can be fopen'ed
|
||||
# CONFIG_NAME_MAX - The maximum size of a file name.
|
||||
# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
|
||||
# on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_NUNGET_CHARS - Number of characters that can be
|
||||
# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
|
||||
# structures. The system manages a pool of preallocated
|
||||
# message structures to minimize dynamic allocations
|
||||
# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
|
||||
# a fixed payload size given by this settin (does not include
|
||||
# other message structure overhead.
|
||||
# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
|
||||
# can be passed to a watchdog handler
|
||||
# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
|
||||
# structures. The system manages a pool of preallocated
|
||||
# watchdog structures to minimize dynamic allocations
|
||||
# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
|
||||
# timer structures. The system manages a pool of preallocated
|
||||
# timer structures to minimize dynamic allocations. Set to
|
||||
# zero for all dynamic allocations.
|
||||
#
|
||||
CONFIG_MAX_TASKS=16
|
||||
CONFIG_MAX_TASK_ARGS=4
|
||||
CONFIG_NPTHREAD_KEYS=4
|
||||
CONFIG_NFILE_DESCRIPTORS=8
|
||||
CONFIG_NFILE_STREAMS=8
|
||||
CONFIG_NAME_MAX=32
|
||||
CONFIG_STDIO_BUFFER_SIZE=256
|
||||
CONFIG_NUNGET_CHARS=2
|
||||
CONFIG_PREALLOC_MQ_MSGS=4
|
||||
CONFIG_MQ_MAXMSGSIZE=32
|
||||
CONFIG_MAX_WDOGPARMS=2
|
||||
CONFIG_PREALLOC_WDOGS=4
|
||||
CONFIG_PREALLOC_TIMERS=4
|
||||
|
||||
#
|
||||
# Filesystem configuration
|
||||
#
|
||||
# CONFIG_FS_FAT - Enable FAT filesystem support
|
||||
# CONFIG_FAT_SECTORSIZE - Max supported sector size
|
||||
# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
|
||||
# file name support.
|
||||
# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims
|
||||
# patents on FAT long file name technology. Please read the
|
||||
# disclaimer in the top-level COPYING file and only enable this
|
||||
# feature if you understand these issues.
|
||||
# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
|
||||
# default, maximum long file name is 255 bytes. This can eat up
|
||||
# a lot of memory (especially stack space). If you are willing
|
||||
# to live with some non-standard, short long file names, then
|
||||
# define this value. A good choice would be the same value as
|
||||
# selected for CONFIG_NAME_MAX which will limit the visibility
|
||||
# of longer file names anyway.
|
||||
# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
|
||||
# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH.
|
||||
# This must have one of the values of 0xff or 0x00.
|
||||
# Default: 0xff.
|
||||
# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
|
||||
# don't both with file chunks smaller than this number of data bytes.
|
||||
# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
|
||||
# Default: 255.
|
||||
# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
|
||||
# don't both with file chunks smaller than this number of data bytes.
|
||||
# Default: 32.
|
||||
# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
|
||||
# packing files together toward the end of the file or, if file are
|
||||
# deleted at the end of the file, clean up can simply mean erasing
|
||||
# the end of FLASH memory so that it can be re-used again. However,
|
||||
# doing this can also harm the life of the FLASH part because it can
|
||||
# mean that the tail end of the FLASH is re-used too often. This
|
||||
# threshold determines if/when it is worth erased the tail end of FLASH
|
||||
# and making it available for re-use (and possible over-wear).
|
||||
# Default: 8192.
|
||||
# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
|
||||
# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
|
||||
# option will enable a limited form of memory mapping that is
|
||||
# implemented by copying whole files into memory.
|
||||
#
|
||||
CONFIG_FS_FAT=n
|
||||
CONFIG_FAT_LCNAMES=n
|
||||
CONFIG_FAT_LFN=n
|
||||
CONFIG_FAT_MAXFNAME=32
|
||||
CONFIG_FS_NXFFS=n
|
||||
CONFIG_FS_ROMFS=n
|
||||
|
||||
#
|
||||
# SPI-based MMC/SD driver
|
||||
#
|
||||
# CONFIG_MMCSD_NSLOTS
|
||||
# Number of MMC/SD slots supported by the driver
|
||||
# CONFIG_MMCSD_READONLY
|
||||
# Provide read-only access (default is read/write)
|
||||
# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
|
||||
# Default is 20MHz.
|
||||
#
|
||||
CONFIG_MMCSD_NSLOTS=1
|
||||
CONFIG_MMCSD_READONLY=n
|
||||
CONFIG_MMCSD_SPICLOCK=12500000
|
||||
|
||||
#
|
||||
# Block driver buffering
|
||||
#
|
||||
# CONFIG_FS_READAHEAD
|
||||
# Enable read-ahead buffering
|
||||
# CONFIG_FS_WRITEBUFFER
|
||||
# Enable write buffering
|
||||
#
|
||||
CONFIG_FS_READAHEAD=n
|
||||
CONFIG_FS_WRITEBUFFER=n
|
||||
|
||||
#
|
||||
# SDIO-based MMC/SD driver
|
||||
#
|
||||
# CONFIG_SDIO_DMA
|
||||
# SDIO driver supports DMA
|
||||
# CONFIG_MMCSD_MMCSUPPORT
|
||||
# Enable support for MMC cards
|
||||
# CONFIG_MMCSD_HAVECARDDETECT
|
||||
# SDIO driver card detection is 100% accurate
|
||||
#
|
||||
CONFIG_SDIO_DMA=y
|
||||
CONFIG_MMCSD_MMCSUPPORT=n
|
||||
CONFIG_MMCSD_HAVECARDDETECT=n
|
||||
|
||||
#
|
||||
# TCP/IP and UDP support via uIP
|
||||
# CONFIG_NET - Enable or disable all network features
|
||||
# CONFIG_NET_IPv6 - Build in support for IPv6
|
||||
# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
|
||||
# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
|
||||
# CONFIG_NET_BUFSIZE - uIP buffer size
|
||||
# CONFIG_NET_TCP - TCP support on or off
|
||||
# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
|
||||
# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
|
||||
# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
|
||||
# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
|
||||
# accept() is called. The size of the backlog is selected when listen() is called.
|
||||
# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
|
||||
# CONFIG_NET_UDP - UDP support on or off
|
||||
# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
|
||||
# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
|
||||
# CONFIG_NET_ICMP - ICMP ping response support on or off
|
||||
# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
|
||||
# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
|
||||
# CONFIG_NET_STATISTICS - uIP statistics on or off
|
||||
# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
|
||||
# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
|
||||
# CONFIG_NET_BROADCAST - Broadcast support
|
||||
# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
|
||||
#
|
||||
CONFIG_NET=n
|
||||
CONFIG_NET_IPv6=n
|
||||
CONFIG_NSOCKET_DESCRIPTORS=0
|
||||
CONFIG_NET_SOCKOPTS=y
|
||||
CONFIG_NET_BUFSIZE=420
|
||||
CONFIG_NET_TCP=n
|
||||
CONFIG_NET_TCP_CONNS=40
|
||||
CONFIG_NET_MAX_LISTENPORTS=40
|
||||
CONFIG_NET_UDP=n
|
||||
CONFIG_NET_UDP_CHECKSUMS=y
|
||||
#CONFIG_NET_UDP_CONNS=10
|
||||
CONFIG_NET_ICMP=n
|
||||
CONFIG_NET_ICMP_PING=n
|
||||
#CONFIG_NET_PINGADDRCONF=0
|
||||
CONFIG_NET_STATISTICS=y
|
||||
#CONFIG_NET_RECEIVE_WINDOW=
|
||||
#CONFIG_NET_ARPTAB_SIZE=8
|
||||
CONFIG_NET_BROADCAST=n
|
||||
#CONFIG_NET_FWCACHE_SIZE=2
|
||||
|
||||
#
|
||||
# UIP Network Utilities
|
||||
# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
|
||||
# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
|
||||
#
|
||||
CONFIG_NET_DHCP_LIGHT=n
|
||||
CONFIG_NET_RESOLV_ENTRIES=4
|
||||
|
||||
#
|
||||
# USB Device Configuration
|
||||
#
|
||||
# CONFIG_USBDEV
|
||||
# Enables USB device support
|
||||
# CONFIG_USBDEV_ISOCHRONOUS
|
||||
# Build in extra support for isochronous endpoints
|
||||
# CONFIG_USBDEV_DUALSPEED
|
||||
# Hardware handles high and full speed operation (USB 2.0)
|
||||
# CONFIG_USBDEV_SELFPOWERED
|
||||
# Will cause USB features to indicate that the device is
|
||||
# self-powered
|
||||
# CONFIG_USBDEV_MAXPOWER
|
||||
# Maximum power consumption in mA
|
||||
# CONFIG_USBDEV_TRACE
|
||||
# Enables USB tracing for debug
|
||||
# CONFIG_USBDEV_TRACE_NRECORDS
|
||||
# Number of trace entries to remember
|
||||
#
|
||||
CONFIG_USBDEV=y
|
||||
CONFIG_USBDEV_ISOCHRONOUS=n
|
||||
CONFIG_USBDEV_DUALSPEED=n
|
||||
CONFIG_USBDEV_SELFPOWERED=y
|
||||
CONFIG_USBDEV_REMOTEWAKEUP=n
|
||||
CONFIG_USBDEV_MAXPOWER=100
|
||||
CONFIG_USBDEV_TRACE=n
|
||||
CONFIG_USBDEV_TRACE_NRECORDS=128
|
||||
|
||||
#
|
||||
# USB Serial Device Configuration
|
||||
#
|
||||
# CONFIG_USBSER
|
||||
# Enable compilation of the USB serial driver
|
||||
# CONFIG_USBSER_EPINTIN
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# interrupt IN operation
|
||||
# CONFIG_USBSER_EPBULKOUT
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# bulk OUT operation
|
||||
# CONFIG_USBSER_EPBULKIN
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# bulk IN operation
|
||||
# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
|
||||
# The number of write/read requests that can be in flight
|
||||
# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
|
||||
# The vendor ID code/string
|
||||
# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
|
||||
# The product ID code/string
|
||||
# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
|
||||
# Size of the serial receive/transmit buffers
|
||||
#
|
||||
CONFIG_USBSER=n
|
||||
CONFIG_USBSER_EPINTIN=1
|
||||
CONFIG_USBSER_EPBULKOUT=2
|
||||
CONFIG_USBSER_EPBULKIN=3
|
||||
CONFIG_USBSER_NWRREQS=4
|
||||
CONFIG_USBSER_NRDREQS=4
|
||||
CONFIG_USBSER_VENDORID=0x067b
|
||||
CONFIG_USBSER_PRODUCTID=0x2303
|
||||
CONFIG_USBSER_VENDORSTR="Nuttx"
|
||||
CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
|
||||
CONFIG_USBSER_RXBUFSIZE=512
|
||||
CONFIG_USBSER_TXBUFSIZE=512
|
||||
|
||||
#
|
||||
# USB Storage Device Configuration
|
||||
#
|
||||
# CONFIG_USBSTRG
|
||||
# Enable compilation of the USB storage driver
|
||||
# CONFIG_USBSTRG_EP0MAXPACKET
|
||||
# Max packet size for endpoint 0
|
||||
# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
|
||||
# The logical 7-bit address of a hardware endpoints that support
|
||||
# bulk OUT and IN operations
|
||||
# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
|
||||
# The number of write/read requests that can be in flight
|
||||
# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
|
||||
# The size of the buffer in each write/read request. This
|
||||
# value needs to be at least as large as the endpoint
|
||||
# maxpacket and ideally as large as a block device sector.
|
||||
# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
|
||||
# The vendor ID code/string
|
||||
# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
|
||||
# The product ID code/string
|
||||
# CONFIG_USBSTRG_REMOVABLE
|
||||
# Select if the media is removable
|
||||
#
|
||||
CONFIG_USBSTRG=y
|
||||
CONFIG_USBSTRG_EP0MAXPACKET=64
|
||||
CONFIG_USBSTRG_EPBULKOUT=2
|
||||
CONFIG_USBSTRG_EPBULKIN=5
|
||||
CONFIG_USBSTRG_NRDREQS=2
|
||||
CONFIG_USBSTRG_NWRREQS=2
|
||||
CONFIG_USBSTRG_BULKINREQLEN=256
|
||||
CONFIG_USBSTRG_BULKOUTREQLEN=256
|
||||
CONFIG_USBSTRG_VENDORID=0x584e
|
||||
CONFIG_USBSTRG_VENDORSTR="NuttX"
|
||||
CONFIG_USBSTRG_PRODUCTID=0x5342
|
||||
CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
|
||||
CONFIG_USBSTRG_VERSIONNO=0x0399
|
||||
CONFIG_USBSTRG_REMOVABLE=y
|
||||
|
||||
#
|
||||
# Settings for examples/uip
|
||||
#
|
||||
CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_UIP_DHCPC=n
|
||||
|
||||
#
|
||||
# Settings for examples/nettest
|
||||
CONFIG_EXAMPLE_NETTEST_SERVER=n
|
||||
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
|
||||
CONFIG_EXAMPLE_NETTEST_NOMAC=n
|
||||
CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
|
||||
|
||||
#
|
||||
# Settings for examples/ostest
|
||||
#
|
||||
CONFIG_EXAMPLES_OSTEST_LOOPS=1
|
||||
CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
|
||||
CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
|
||||
|
||||
#
|
||||
# Settings for apps/nshlib
|
||||
#
|
||||
# CONFIG_NSH_BUILTIN_APPS - Support external registered,
|
||||
# "named" applications that can be executed from the NSH
|
||||
# command line (see apps/README.txt for more information).
|
||||
# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
|
||||
# CONFIG_NSH_STRERROR - Use strerror(errno)
|
||||
# CONFIG_NSH_LINELEN - Maximum length of one command line
|
||||
# CONFIG_NSH_STACKSIZE - Stack size to use for new threads.
|
||||
# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
|
||||
# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
|
||||
# CONFIG_NSH_DISABLEBG - Disable background commands
|
||||
# CONFIG_NSH_ROMFSETC - Use startup script in /etc
|
||||
# CONFIG_NSH_CONSOLE - Use serial console front end
|
||||
# CONFIG_NSH_CONDEV - Select the serial device used to support
|
||||
# the NSH console. Default: stdin and stdout
|
||||
# CONFIG_NSH_TELNET - Use telnetd console front end
|
||||
# CONFIG_NSH_ARCHINIT - Platform provides architecture
|
||||
# specific initialization (nsh_archinitialize()).
|
||||
#
|
||||
# If CONFIG_NSH_TELNET is selected:
|
||||
# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
|
||||
# CONFIG_NSH_DHCPC - Obtain address using DHCP
|
||||
# CONFIG_NSH_IPADDR - Provides static IP address
|
||||
# CONFIG_NSH_DRIPADDR - Provides static router IP address
|
||||
# CONFIG_NSH_NETMASK - Provides static network mask
|
||||
# CONFIG_NSH_NOMAC - Use a bogus MAC address
|
||||
#
|
||||
# If CONFIG_NSH_ROMFSETC is selected:
|
||||
# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
|
||||
# CONFIG_NSH_INITSCRIPT - Relative path to init script
|
||||
# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
|
||||
# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
|
||||
# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
|
||||
# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
|
||||
# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
|
||||
# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
|
||||
#
|
||||
CONFIG_NSH_BUILTIN_APPS=n
|
||||
CONFIG_NSH_FILEIOSIZE=512
|
||||
CONFIG_NSH_STRERROR=n
|
||||
CONFIG_NSH_LINELEN=64
|
||||
CONFIG_NSH_STACKSIZE=2048
|
||||
CONFIG_NSH_NESTDEPTH=3
|
||||
CONFIG_NSH_DISABLESCRIPT=n
|
||||
CONFIG_NSH_DISABLEBG=n
|
||||
CONFIG_NSH_ROMFSETC=n
|
||||
CONFIG_NSH_CONSOLE=y
|
||||
#CONFIG_NSH_CONDEV="/dev/ttyS1"
|
||||
CONFIG_NSH_TELNET=n
|
||||
CONFIG_NSH_ARCHINIT=y
|
||||
CONFIG_NSH_IOBUFFER_SIZE=512
|
||||
CONFIG_NSH_DHCPC=n
|
||||
CONFIG_NSH_NOMAC=n
|
||||
CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_NSH_ROMFSMOUNTPT="/etc"
|
||||
CONFIG_NSH_INITSCRIPT="init.d/rcS"
|
||||
CONFIG_NSH_ROMFSDEVNO=0
|
||||
CONFIG_NSH_ROMFSSECTSIZE=64
|
||||
CONFIG_NSH_FATDEVNO=1
|
||||
CONFIG_NSH_FATSECTSIZE=512
|
||||
CONFIG_NSH_FATNSECTORS=1024
|
||||
CONFIG_NSH_FATMOUNTPT=/tmp
|
||||
|
||||
#
|
||||
# Architecture-specific NSH options
|
||||
#
|
||||
CONFIG_NSH_MMCSDSPIPORTNO=0
|
||||
CONFIG_NSH_MMCSDSLOTNO=0
|
||||
CONFIG_NSH_MMCSDMINOR=0
|
||||
|
||||
#
|
||||
# Settings for examples/usbserial
|
||||
#
|
||||
# CONFIG_EXAMPLES_USBSERIAL_INONLY
|
||||
# Only verify IN (device-to-host) data transfers. Default: both
|
||||
# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
|
||||
# Only verify OUT (host-to-device) data transfers. Default: both
|
||||
# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
|
||||
# Send only small, single packet messages. Default: Send large and small.
|
||||
# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
|
||||
# Send only large, multi-packet messages. Default: Send large and small.
|
||||
#
|
||||
CONFIG_EXAMPLES_USBSERIAL_INONLY=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
|
||||
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
|
||||
|
||||
#
|
||||
# Settings for examples/usbstorage
|
||||
#
|
||||
# CONFIG_EXAMPLES_USBSTRG_BUILTIN
|
||||
# This example can be built as two NSH "built-in" commands if this option
|
||||
# is selection: 'msconn' will connect the USB mass storage device; 'msdis'
|
||||
# will disconnect the USB storage device.
|
||||
# CONFIG_EXAMPLES_USBSTRG_NLUNS
|
||||
# Defines the number of logical units (LUNs) exported by the USB storage
|
||||
# driver. Each LUN corresponds to one exported block driver (or partition
|
||||
# of a block driver). May be 1, 2, or 3. Default is 1.
|
||||
# CONFIG_EXAMPLES_USBSTRG_DEVMINOR1
|
||||
# The minor device number of the block driver for the first LUN. For
|
||||
# example, N in /dev/mmcsdN. Used for registering the block driver. Default
|
||||
# is zero.
|
||||
# CONFIG_EXAMPLES_USBSTRG_DEVPATH1
|
||||
# The full path to the registered block driver. Default is "/dev/mmcsd0"
|
||||
# CONFIG_EXAMPLES_USBSTRG_DEVMINOR2 and CONFIG_EXAMPLES_USBSTRG_DEVPATH2
|
||||
# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBSTRG_NLUNS
|
||||
# is 2 or 3. No defaults.
|
||||
# CONFIG_EXAMPLES_USBSTRG_DEVMINOR3 and CONFIG_EXAMPLES_USBSTRG_DEVPATH3
|
||||
# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBSTRG_NLUNS
|
||||
# is 3. No defaults.
|
||||
# CONFIG_EXAMPLES_USBSTRG_DEBUGMM
|
||||
# Enables some debug tests to check for memory usage and memory leaks.
|
||||
#
|
||||
# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB), then
|
||||
# the example code will also manage the USB trace output. The amount of trace output
|
||||
# can be controlled using:
|
||||
#
|
||||
# CONFIG_EXAMPLES_USBSTRG_TRACEINIT
|
||||
# Show initialization events
|
||||
# CONFIG_EXAMPLES_USBSTRG_TRACECLASS
|
||||
# Show class driver events
|
||||
# CONFIG_EXAMPLES_USBSTRG_TRACETRANSFERS
|
||||
# Show data transfer events
|
||||
# CONFIG_EXAMPLES_USBSTRG_TRACECONTROLLER
|
||||
# Show controller events
|
||||
# CONFIG_EXAMPLES_USBSTRG_TRACEINTERRUPTS
|
||||
# Show interrupt-related events.
|
||||
#
|
||||
CONFIG_EXAMPLES_USBSTRG_BUILTIN=n
|
||||
CONFIG_EXAMPLES_USBSTRG_NLUNS=1
|
||||
CONFIG_EXAMPLES_USBSTRG_DEVMINOR1=0
|
||||
CONFIG_EXAMPLES_USBSTRG_DEVPATH1="/dev/mmcsd0"
|
||||
CONFIG_EXAMPLES_USBSTRG_DEBUGMM=n
|
||||
CONFIG_EXAMPLES_USBSTRG_TRACEINIT=n
|
||||
CONFIG_EXAMPLES_USBSTRG_TRACECLASS=n
|
||||
CONFIG_EXAMPLES_USBSTRG_TRACETRANSFERS=n
|
||||
CONFIG_EXAMPLES_USBSTRG_TRACECONTROLLER=n
|
||||
CONFIG_EXAMPLES_USBSTRG_TRACEINTERRUPTS=n
|
||||
|
||||
#
|
||||
# Stack and heap information
|
||||
#
|
||||
# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
|
||||
# operation from FLASH but must copy initialized .data sections to RAM.
|
||||
# (should also be =n for the Hy-Mini STM32v which always runs from flash)
|
||||
# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH
|
||||
# but copy themselves entirely into RAM for better performance.
|
||||
# CONFIG_CUSTOM_STACK - The up_ implementation will handle
|
||||
# all stack operations outside of the nuttx model.
|
||||
# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
|
||||
# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
|
||||
# This is the thread that (1) performs the inital boot of the system up
|
||||
# to the point where user_start() is spawned, and (2) there after is the
|
||||
# IDLE thread that executes only when there is no other thread ready to
|
||||
# run.
|
||||
# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
|
||||
# for the main user thread that begins at the user_start() entry point.
|
||||
# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
|
||||
# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
|
||||
# CONFIG_HEAP_BASE - The beginning of the heap
|
||||
# CONFIG_HEAP_SIZE - The size of the heap
|
||||
#
|
||||
CONFIG_BOOT_RUNFROMFLASH=n
|
||||
CONFIG_BOOT_COPYTORAM=n
|
||||
CONFIG_CUSTOM_STACK=n
|
||||
CONFIG_STACK_POINTER=
|
||||
CONFIG_IDLETHREAD_STACKSIZE=1024
|
||||
CONFIG_USERMAIN_STACKSIZE=2048
|
||||
CONFIG_PTHREAD_STACK_MIN=256
|
||||
CONFIG_PTHREAD_STACK_DEFAULT=2048
|
||||
CONFIG_HEAP_BASE=
|
||||
CONFIG_HEAP_SIZE=
|
|
@ -0,0 +1,112 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/usbstorage/ld.script
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
|
||||
* 64Kb of SRAM beginning at address 0x2000:0000. When booting from FLASH,
|
||||
* FLASH memory is aliased to address 0x0000:0000 where the code expects to
|
||||
* begin execution by jumping to the entry point in the 0x0800:0000 address
|
||||
* range.
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x08000000, LENGTH = 512K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} >sram
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
|
@ -0,0 +1,111 @@
|
|||
/****************************************************************************
|
||||
* configs/hymini-stm32v/usbstorage/ld.script.dfu
|
||||
*
|
||||
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
|
||||
* 64Kb of SRAM beginning at address 0x2000:0000. Here we assume that the
|
||||
* Hy-Mini STM32v's DFU bootloader is being used. In that case, the corrct
|
||||
* load .text load address is 0x08003000 (leaving 464Kb).
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x08003000, LENGTH = 464K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} >sram
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
|
@ -0,0 +1,47 @@
|
|||
#!/bin/bash
|
||||
# configs/hymini-stm32v/dfu/setenv.sh
|
||||
#
|
||||
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
|
||||
if [ "$(basename $0)" = "setenv.sh" ] ; then
|
||||
echo "You must source this script, not run it!" 1>&2
|
||||
exit 1
|
||||
fi
|
||||
|
||||
if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi
|
||||
|
||||
WD=`pwd`
|
||||
export RIDE_BIN="/cygdrive/c/Program Files/Raisonance/Ride/arm-gcc/bin"
|
||||
export BUILDROOT_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
|
||||
export PATH="${BUILDROOT_BIN}:${RIDE_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
|
||||
|
||||
echo "PATH : ${PATH}"
|
|
@ -179,14 +179,14 @@ static inline void ads7843e_select(FAR struct spi_dev_s *spi)
|
|||
#else
|
||||
static void ads7843e_select(FAR struct spi_dev_s *spi)
|
||||
{
|
||||
/* Select P14201 chip (locking the SPI bus in case there are multiple
|
||||
/* Select ADS7843 chip (locking the SPI bus in case there are multiple
|
||||
* devices competing for the SPI bus
|
||||
*/
|
||||
|
||||
SPI_LOCK(spi, true);
|
||||
SPI_SELECT(spi, SPIDEV_TOUCHSCREEN, true);
|
||||
|
||||
/* Now make sure that the SPI bus is configured for the P14201 (it
|
||||
/* Now make sure that the SPI bus is configured for the ADS7843 (it
|
||||
* might have gotten configured for a different device while unlocked)
|
||||
*/
|
||||
|
||||
|
@ -201,7 +201,7 @@ static void ads7843e_select(FAR struct spi_dev_s *spi)
|
|||
*
|
||||
* Description:
|
||||
* De-select the SPI, unlocking as necessary. This function must be
|
||||
* after completing asequence of SPI operations. If we are sharing the SPI
|
||||
* after completing a sequence of SPI operations. If we are sharing the SPI
|
||||
* bus with other devices (CONFIG_SPI_OWNBUS undefined) then we need to
|
||||
* un-lock the SPI bus for each transfer, possibly losing the current
|
||||
* configuration.
|
||||
|
@ -226,7 +226,7 @@ static inline void ads7843e_deselect(FAR struct spi_dev_s *spi)
|
|||
#else
|
||||
static void ads7843e_deselect(FAR struct spi_dev_s *spi)
|
||||
{
|
||||
/* De-select P14201 chip and relinquish the SPI bus. */
|
||||
/* De-select ADS7843 chip and relinquish the SPI bus. */
|
||||
|
||||
SPI_SELECT(spi, SPIDEV_TOUCHSCREEN, false);
|
||||
SPI_LOCK(spi, false);
|
||||
|
@ -237,7 +237,7 @@ static void ads7843e_deselect(FAR struct spi_dev_s *spi)
|
|||
* Function: ads7843e_configspi
|
||||
*
|
||||
* Description:
|
||||
* Configure the SPI for use with the ADS7843E. This funcution should be
|
||||
* Configure the SPI for use with the ADS7843E. This function should be
|
||||
* called once during touchscreen initialization to configure the SPI
|
||||
* bus. Note that if CONFIG_SPI_OWNBUS is not defined, then this function
|
||||
* does nothing.
|
||||
|
@ -257,7 +257,7 @@ static inline void ads7843e_configspi(FAR struct spi_dev_s *spi)
|
|||
idbg("Mode: %d Bits: 8 Frequency: %d\n",
|
||||
CONFIG_ADS7843E_SPIMODE, CONFIG_ADS7843E_FREQUENCY);
|
||||
|
||||
/* Configure SPI for the P14201. But only if we own the SPI bus. Otherwise, don't
|
||||
/* Configure SPI for the ADS7843. But only if we own the SPI bus. Otherwise, don't
|
||||
* bother because it might change.
|
||||
*/
|
||||
|
||||
|
@ -265,7 +265,7 @@ static inline void ads7843e_configspi(FAR struct spi_dev_s *spi)
|
|||
SPI_SELECT(spi, SPIDEV_TOUCHSCREEN, true);
|
||||
SPI_SETMODE(spi, CONFIG_ADS7843E_SPIMODE);
|
||||
SPI_SETBITS(spi, 8);
|
||||
SPI_SETFREQUENCY(spi, CONFIG_ADS7843E_FREQUENCY)
|
||||
SPI_SETFREQUENCY(spi, CONFIG_ADS7843E_FREQUENCY);
|
||||
SPI_SELECT(spi, SPIDEV_TOUCHSCREEN, false);
|
||||
#endif
|
||||
}
|
||||
|
@ -326,13 +326,13 @@ static void ads7843e_notify(FAR struct ads7843e_dev_s *priv)
|
|||
if (priv->nwaiters > 0)
|
||||
{
|
||||
/* After posting this semaphore, we need to exit because the ADS7843E
|
||||
* is no longer avaialable.
|
||||
* is no longer available.
|
||||
*/
|
||||
|
||||
sem_post(&priv->waitsem);
|
||||
}
|
||||
|
||||
/* If there are threads waiting on poll() for ADS7843E data to become availabe,
|
||||
/* If there are threads waiting on poll() for ADS7843E data to become available,
|
||||
* then wake them up now. NOTE: we wake up all waiting threads because we
|
||||
* do not know that they are going to do. If they all try to read the data,
|
||||
* then some make end up blocking after all.
|
||||
|
@ -363,7 +363,7 @@ static int ads7843e_sample(FAR struct ads7843e_dev_s *priv,
|
|||
int ret = -EAGAIN;
|
||||
|
||||
/* Interrupts me be disabled when this is called to (1) prevent posting
|
||||
* of semphores from interrupt handlers, and (2) to prevent sampled data
|
||||
* of semaphores from interrupt handlers, and (2) to prevent sampled data
|
||||
* from changing until it has been reported.
|
||||
*/
|
||||
|
||||
|
@ -383,7 +383,7 @@ static int ads7843e_sample(FAR struct ads7843e_dev_s *priv,
|
|||
|
||||
if (sample->contact == CONTACT_UP)
|
||||
{
|
||||
/* Next.. no contract. Increment the ID so that next contact ID will be unique */
|
||||
/* Next.. no contact. Increment the ID so that next contact ID will be unique */
|
||||
|
||||
priv->sample.contact = CONTACT_NONE;
|
||||
priv->id++;
|
||||
|
@ -414,7 +414,7 @@ static int ads7843e_waitsample(FAR struct ads7843e_dev_s *priv,
|
|||
int ret;
|
||||
|
||||
/* Interrupts me be disabled when this is called to (1) prevent posting
|
||||
* of semphores from interrupt handlers, and (2) to prevent sampled data
|
||||
* of semaphores from interrupt handlers, and (2) to prevent sampled data
|
||||
* from changing until it has been reported.
|
||||
*
|
||||
* In addition, we will also disable pre-emption to prevent other threads
|
||||
|
@ -432,7 +432,7 @@ static int ads7843e_waitsample(FAR struct ads7843e_dev_s *priv,
|
|||
sem_post(&priv->devsem);
|
||||
|
||||
/* Try to get the a sample... if we cannot, then wait on the semaphore
|
||||
* that is posted when new sample data is availble.
|
||||
* that is posted when new sample data is available.
|
||||
*/
|
||||
|
||||
while (ads7843e_sample(priv, sample) < 0)
|
||||
|
@ -501,7 +501,7 @@ static int ads7843e_schedule(FAR struct ads7843e_dev_s *priv)
|
|||
DEBUGASSERT(config != NULL);
|
||||
|
||||
/* Disable further interrupts. ADS7843E interrupts will be re-enabled
|
||||
* after the worker thread exectues.
|
||||
* after the worker thread executes.
|
||||
*/
|
||||
|
||||
config->enable(config, false);
|
||||
|
@ -568,7 +568,7 @@ static void ads7843e_worker(FAR void *arg)
|
|||
|
||||
if (!pendown)
|
||||
{
|
||||
/* Ignore the interrupt if the pen was already down (CONTACT_NONE == pen up and
|
||||
/* Ignore the interrupt if the pen was already up (CONTACT_NONE == pen up and
|
||||
* already reported. CONTACT_UP == pen up, but not reported)
|
||||
*/
|
||||
|
||||
|
@ -614,7 +614,7 @@ static void ads7843e_worker(FAR void *arg)
|
|||
priv->sample.id = priv->id;
|
||||
priv->penchange = true;
|
||||
|
||||
/* Notify any waiters that nes ADS7843E data is available */
|
||||
/* Notify any waiters that new ADS7843E data is available */
|
||||
|
||||
ads7843e_notify(priv);
|
||||
|
||||
|
@ -1055,7 +1055,7 @@ errout:
|
|||
*
|
||||
* Input Parameters:
|
||||
* dev - An SPI driver instance
|
||||
* config - Persistant board configuration data
|
||||
* config - Persistent board configuration data
|
||||
* minor - The input device minor number
|
||||
*
|
||||
* Returned Value:
|
||||
|
|
|
@ -276,7 +276,7 @@ static void at45db_lock(struct at45db_dev_s *priv)
|
|||
* the SPI buss. We will retain that exclusive access until the bus is unlocked.
|
||||
*/
|
||||
|
||||
(void)SPI_LOCK(priv->spi, true);
|
||||
SPI_LOCK(priv->spi, true);
|
||||
|
||||
/* After locking the SPI bus, the we also need call the setfrequency, setbits, and
|
||||
* setmode methods to make sure that the SPI is properly configured for the device.
|
||||
|
@ -295,7 +295,7 @@ static void at45db_lock(struct at45db_dev_s *priv)
|
|||
|
||||
static inline void at45db_unlock(struct at45db_dev_s *priv)
|
||||
{
|
||||
(void)SPI_LOCK(priv->spi, false);
|
||||
SPI_LOCK(priv->spi, false);
|
||||
}
|
||||
|
||||
/************************************************************************************
|
||||
|
|
|
@ -196,7 +196,7 @@ static void m25p_lock(FAR struct spi_dev_s *dev)
|
|||
* the SPI buss. We will retain that exclusive access until the bus is unlocked.
|
||||
*/
|
||||
|
||||
(void)SPI_LOCK(dev, true);
|
||||
SPI_LOCK(dev, true);
|
||||
|
||||
/* After locking the SPI bus, the we also need call the setfrequency, setbits, and
|
||||
* setmode methods to make sure that the SPI is properly configured for the device.
|
||||
|
@ -215,7 +215,7 @@ static void m25p_lock(FAR struct spi_dev_s *dev)
|
|||
|
||||
static inline void m25p_unlock(FAR struct spi_dev_s *dev)
|
||||
{
|
||||
(void)SPI_LOCK(dev, false);
|
||||
SPI_LOCK(dev, false);
|
||||
}
|
||||
|
||||
/************************************************************************************
|
||||
|
|
File diff suppressed because it is too large
Load Diff
|
@ -67,7 +67,7 @@
|
|||
#endif
|
||||
|
||||
#ifndef CONFIG_ADS7843E_SPIMODE
|
||||
# define CONFIG_ADS7843E_SPIMODE SPIDEV_MODE1
|
||||
# define CONFIG_ADS7843E_SPIMODE SPIDEV_MODE0
|
||||
#endif
|
||||
|
||||
/* Check for some required settings. This can save the user a lot of time
|
||||
|
@ -150,7 +150,7 @@ extern "C" {
|
|||
*
|
||||
* Input Parameters:
|
||||
* dev - An SPI driver instance
|
||||
* config - Persistant board configuration data
|
||||
* config - Persistent board configuration data
|
||||
* minor - The input device minor number
|
||||
*
|
||||
* Returned Value:
|
||||
|
|
Loading…
Reference in New Issue