After this patch, Several "local-ip" and "remote-ip" lines are accepted
under "listen" and "asp" VTY nodes, allowing to configure an SCTP
connection with multiple connections, hence allowing control of SCTP
multi-homing features.
libosmo-sccp clients such as osmo-bsc and osmo-msc also gain support for
this feature with this commit.
Related: OS#3608
Depends: libosmocore.git Ic8681d9e093216c99c6bca4be81c31ef83688ed1
Depends: libosmo-netif.git I0fe62f518e195db4e34f3b0ad1762bb57ba9d92a
Change-Id: Ibd15de7a4e00dbec78ff2e2dd6a686b0f3af22de
When receiving SCCP messages from an IPA peer/ASP, osmo-stp so far
unconditionally inserted origin/destination point codes int the SCCP
called / calling party addresses.
This behaviro is now made optional with the introduction of the
following per-AS configuration:
"point-code override patch-sccp (disabled|both)"
The default behavior is switched from 'both' to 'disabled' at the same
time.
Change-Id: I535e2170adadfe755d2bcbf5bbf4556bebb77737
Closes: OS#4219
The previous hardcoded SCCP timers may cause SCCP connection releases, if the
peer is configured with far lower timers than libosmo-sccp. Testing with a
specific SCCPlite MSC, I experienced an iar of just over three minutes, meaning
that calls would be cut off by the MSC, since the osmo-bsc failed to send an
Inactivity Timer message until seven minutes have passed.
With this patch, SCCP timers are configurable by the user.
Define constant global default timers, and variable user-configurable timers
with each osmo_sccp_instance.
Add VTY UI to configure the timers. Users must call osmo_sccp_vty_init() to get
the sccp-timer config nodes under the 'cs7' node. Show the new UI in
ss7_asp_test.vty.
Note that even though this function is not new at all, until recently, all of
our SCCP users (osmo-bsc, osmo-msc, osmo-sgsn, osmo-hnbgw) failed to call
osmo_sccp_vty_init(), and thus also missed out on the various 'show' commands
defined in sccp_vty.c. In other words, to benefit from the timer
configurability, the patches to call osmo_sccp_vty_init() must first be merged
to the corresponding master branches.
If a 'sccp-timer' config command occurs, the cs7 instance must allocate an SCCP
instance in order to store the timer config. Do that by calling the recently
added osmo_ss7_ensure_sccp() function.
Hence remove the limitation that the SCCP instance must not be populated from
the "simple" setup function. If we want to configure SCCP timers beforehand,
there must be an SCCP instance for that, and there is no hard reason to require
a NULL SCCP instance, besides the desire to prevent this function from being
invoked twice.
Change-Id: I28a7362aa838e648ecc9b26ee53dbcade81a9d65
For 'show cs7 instance 0 ssn', fix doc string for 'ssn', and add missing one
for the SSN arg. This fixes depending builds that see VTY test failures due to
the missing doc string.
For 'show cs7 instance 0 connectsion', fix doc string for 'connections'.
Change-Id: I214ea51fc6bfa2a9a4dd7c34b43add0c77ffe22e
The 'show cs7 instance 0 sccp-addressbook' command should not be inside the
'cs7' node. That defies the point of naming the instance again, and it falls
out of place of all the other 'show cs7' commands on the VIEW and ENABLE nodes.
Drop the old command within the 'cs7' node without substitution or deprecation.
At the same time, drop dash from 'show cs7 i 0 sccp-addressbook'
There are various other show cs7 commands already defined in sccp_vty.c, which
have 'sccp' as a separate string. Conform to that.
Change-Id: I80e0bc0a91bcd3fb75372045db34592d2d663d41
Fix typo "to long".
Say 'cs7 instance' instead of 'ss7 instance': we are interacting with a user on
the telnet VTY, and that user is configuring a 'cs7 instance'. Especially a
lowercase 'ss7' is potentially confusing ("is there an 'ss7' node?").
Changes show in ss7_asp_test.vty.
Change-Id: Iebb976531576268d58338895a4baadbca6137b80
Define SCCP_STR in sccp_internal.h, because I know that I want to also use it
in osmo_ss7_vty.c.
Fix "Signaling" to "Signalling" upon copying the old string.
Change-Id: Ic93e4771147070a9222c73f80b5f7c29ae7eec35
Add ss7_asp_vty_test, a shim test program with the sole purpose of exposing the
cs7 VTY nodes.
Add ss7_asp_test.vty, transcript for verifying VTY nodes using above program.
Add --enable-external-tests to configure.
Run jenkins.sh with --enable-external-tests.
Change-Id: I6a28684fa24d6e7de568623444297028eba2ab8c
Pau Espin
Harald Welte
Neels Hofmeyr