This provides a solution for configs where there is e.g. a catch-all %any
PSK, while more specific PSKs would be found by the identities of configs
that e.g. use FQDNs as local/remote addresses.
Fixes#2223.
Memory is allocated with calloc, hence set to zero, thus assigning the
numerical value 0 is not required.
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com>
We actually want to wait until the IKE_SA is destroyed, not any of the
CHILD_SAs (even though there might not be that much of a difference
depending on the number of CHILD_SAs).
Fixes#2261.
Previously, the client had to propose no wider selectors than the certificate
permits, otherwise the complete CHILD_SA was rejected. However, with IKEv2
we can dynamically narrow the selectors to what the certificate allows. This
makes client and gateway configurations very simple by just proposing 0.0.0.0/0,
narrowed to selectors the client is permitted to route into the network.
This allows a gateway to enforce the addrblock policy on certificates that
actually have the extension only. For (legacy) certificates not having the
extension, traffic selectors are validated/narrowed by other means, most
likely by the configuration.
Usually, %dynamic is used as traffic selector for transport mode SAs,
however, if wildcard traps are used then the remote TS will be a subnet.
With strongSwan at the remote end that usually works fine as the local
%dynamic TS narrows the proposed TS appropriately. But some
implementations reject non-host TS for transport mode SAs.
Another problem could be if several distinct subnets are configured for a
wildcard trap, as we'd then propose unrelated subnets on that transport
mode SA, which might be problematic even for strongSwan (switch to tunnel
mode and duplicate policies).
Closesstrongswan/strongswan#61.
Some devices always use the oldest IKE_SA to send DPDs and will delete
all IKE_SAs when there is no response. If uniqueness is not enforced
rekeyed IKE_SAs might not get deleted until they expire so we should
respond to DPDs.
References #2090.
When multihomed, a setup might prefer to dynamically stay on the cheapest
available path by using MOBIKE migrations. If the cheapest path goes away and
comes back, we currently stay on the more expensive path to reduce noise and
prevent potential migration issues. This is usually just fine for links not
generating real cost.
If we have more expensive links in the setup, it can be desirable to always
migrate to the cheapest link available. By setting charon.prefer_best_path,
charon tries to migrate to the path using the highest priority link, allowing
an external application to update routes to indirectly control MOBIKE behavior.
This option has no effect if MOBIKE is unavailable.
Disabling MOBIKE and statically configuring a local address should be
enough indication that the user doesn't want to roam to a different
address. There might not be any routes that indicate we can use the
current address but it might still work (e.g. if the address is on an
interface that is not referenced in any routes and the address itself
is neither). This way we avoid switching to another address for routes
that might be available on the system.
We currently don't make much use of COND_STALE anyway when MOBIKE is not
enabled, e.g. to avoid sending DPDs if the connection is seemingly down.
With MOBIKE enabled we don't exactly check that state but we do don't
send DPDs if there is no route/source address available.
This way updates to the mediation config are respected and the order in
which configs are configured/loaded does not matter.
The SQL plugin currently maintains the strong relationship between
mediated and mediation connection (we could theoretically change that to a
string too).
The original name is returned in the new "name" attribute.
This fixes an issue with bindings that map VICI messages to
dictionaries. For instance, in roadwarrior scenarios where every
CHILD_SA has the same name only the information of the last CHILD_SA
would end up in the dictionary for that name.
PINs are stored in a "hidden" credential set, so that its shared
secrets are not exposed via VICI. Since they are not explicitly loaded as
shared secrets via VICI a client might consider them as removed secrets and
remove them.
After an interface disappeared we can't remove the policies correctly as
the name doesn't resolve to the previous index anymore.
And making the policies so specific might not provide that much benefit.
To handle the interfaces on the policies correctly would require some
changes to the child-cfg, kernel-interface etc. so they'd take interface
indices directly so we could target the policies correctly even if an
interface disappeared (or reappeared and got a new index).
The SA ID (src, dst, proto, spi) is unique on ingress.
As such, explicit inbound marking is not needed to match an SA.
On the other hand, requiring inbound SAs to use marks forces the
installation of a mechanism for marking traffic (e.g. iptables) based
on some criteria.
Defining the criteria becomes complicated, for example when required to
support multiple SAs from the same src, especially when traffic is UDP
encapsulated.
This commit removes the assignment of the child_sa mark_in to the inbound SA.
Policies can be arbitrated by existing means - e.g, via netfilter policy
matching or using VTI interfaces - without the need to classify the flows prior
to state matching.
Since the reqid allocator regards the mark value, there is no risk of matching
the wrong policy.
And as explicit marking was required for route-based VPN to work before this
change, it should not cause regressions in existing setups.
Closesstrongswan/strongswan#59.
For table dumps the kernel accepts RTA_PREFSRC to filter the routes, which is
what we do when doing userspace route calculations. For kernel-based route
lookups, however, the RTA_PREFSRC attribute is ignored and we must specify
RTA_SRC for policy based route lookups.
For gateways with many connections, installing routes is often disabled,
as we can use a static route configuration to achieve proper routing with
a single rule. If this is the case, there is no need to dump all routes and
do userspace route lookups, as there is no need to exclude routes we installed
ourself.
Doing kernel-based route lookups is not only faster with may routes, but also
can use the full power of Linux policy based routing; something we can hardly
rebuild in userspace when calculating routes.
When using vici over RPyC and its (awesome) splitbrain, encoding and decoding
strings fails in vici, most likely because of the Monkey-Patch magic splitbrain
uses.
When specifying the implicit UTF-8 as encoding scheme explicitly, Python uses
the correct method to encode/decode the string, making vici useable in
splitbrain contexts.
If this is the first message by the peer, i.e. we expect MID 0, the
message is not pre-processed in the task manager so we ignore it in the
task.
We also make sure to ignore such messages if the extension is disabled
and the peer already sent us one INFORMATIONAL, e.g. a DPD (we'd otherwise
consider the message with MID 0 as a retransmit).
If the responder never sent a message the expected MID is 0. While
the sent MID (M1) SHOULD be increased beyond the known value, it's
not necessarily the case.
Since M2 - 1 would then equal UINT_MAX setting that MID would get ignored
and while we'd return 0 in the notify we'd actually expect 1 afterwards.
Tobias Brunner