Harald Welte
84d28da2d1
add fiducials for automatic mounting of components
2019-06-22 11:52:46 +02:00
Harald Welte
5f08cd82e6
Specify LED series resistor as 100 Ohms
2019-06-22 11:52:46 +02:00
Harald Welte
59403fe0d5
mark R1 as 'DNP' (no stub to U.FL connector)
2019-06-22 11:52:46 +02:00
Harald Welte
e52cc5d731
add placement files for top and bottom
2019-06-22 11:52:46 +02:00
Harald Welte
d32100e71f
import gerber output
2019-06-22 11:52:46 +02:00
Harald Welte
db5e530345
add CAM file for generating gerber output
2019-06-22 11:52:46 +02:00
Harald Welte
0679fbf23e
remove D45014F marking (seeedstudio)
2019-06-22 11:52:46 +02:00
Harald Welte
2b68fcacb8
update the _brd.pdf to include the LED and R13 and correspond with schemstics
2019-06-22 11:52:46 +02:00
Harald Welte
0cb278399a
add updated PDF schematics
2019-06-22 11:52:46 +02:00
Harald Welte
cee9a8682d
approve various ERC changes
2019-06-22 11:52:46 +02:00
Harald Welte
e008d9236b
re-merge my previous changes manually into the project
2019-06-22 11:52:46 +02:00
Harald Welte
b8752f45e0
sylvains branch (ignores some of harald's changes)
2019-06-22 11:52:46 +02:00
Harald Welte
b324e5353c
don't have two SERIAL_RXD labels but one RXD and one TXD
2019-06-22 11:52:46 +02:00
Harald Welte
2c45271d5d
add ublox LEA6T evaluation board design, first version
2019-06-22 11:52:46 +02:00
Harald Welte
6748fe27c1
Merge branch 'laforge/clock-gen-v2'
2019-06-19 19:11:27 +02:00
Harald Welte
accdfd63c6
clock-generator: Move GND via to avoid overlap with N$15
2019-06-19 19:10:51 +02:00
Martin Schramm
e2cdc91a3a
<osmo-clock-gen: add more TVS for exposed signals, clean up and finish
2019-06-19 19:10:50 +02:00
Martin Schramm
436048290a
osmo-clock-gen: capacitive coupling for XA input needed - added 100n
...
This was a remark by tnt, thanks.
2019-06-19 19:10:50 +02:00
Martin Schramm
c3f627affe
clock-generator: compacting + place MTA100 header (solves OSM#4050)
2019-06-19 19:10:50 +02:00
Martin Schramm
425699d67a
clock-generator: changes adressing OSM#4050
...
A shouded UEXT would need much space; no room for an MTA100 yet... tbd
2019-06-19 19:10:50 +02:00
Martin Schramm
4cd9ee1bd7
clock-generator: insert changes discussed so far for v2
...
* selectable VDDIO{1..4} for PLL: either 3V3 or ADJ (VOUT/DAC)
* use SAMD21 instead of SAMD11
* bring some GPIO on pin header
* use GCLK_IO4 (PA10) to feed XA of PLL
2019-06-19 19:10:50 +02:00
Martin Schramm
e1714e7432
clock-generator: add tracking LDO, make PCB four layer
2019-06-19 19:10:50 +02:00
Harald Welte
cdaf319147
WIP: click-generator: Replace U3 (so far SAMD11) with SAMD21
...
Closes: OS#3856
2019-06-19 19:10:50 +02:00
Martin Schramm
85fc4063bb
sfp-*: add OSHW logo, fill ext'd attribs for BOM
2019-05-09 18:33:33 +02:00
Martin Schramm
89cbce6ffb
sfp: update BOMs for both breakout and experimenter PCBs
2019-05-08 20:33:46 +02:00
Harald Welte
f37aa06c2a
clock-converter: Export BOM
2019-02-14 22:06:36 +01:00
Harald Welte
22ad1c0a54
clock-converter: Add attributes with digikey links
2019-02-14 22:06:22 +01:00
Harald Welte
6d4dd1bead
Clock converter for low phase noise sine -> square conversion
2019-02-02 11:50:41 +01:00
Harald Welte
bbbd83c9dd
clock-gen: Add BOM information + PDF exports of schematics
2019-01-28 12:38:59 +01:00
Harald Welte
0240e5c8c9
clock-gen: Update gpio spreadsheet with all assignments
...
The assignments have been chosen to be nearly identical to the
SAMD11-XPRO board.
2019-01-27 19:17:06 +01:00
Harald Welte
fcc91db897
Merge branch 'laforge/clock-gen'
2019-01-27 18:24:51 +01:00
Harald Welte
ff2d7b03e0
clock-gen: Minor changes; final version as ordered
...
* move DC jack to extend beyond PCB edge into front panel
* harmonize component variants (10n only 0402, 4.7u only 0805)
* add "sysmocom" as manufacturer name (WEEE requirement)
2019-01-27 18:17:36 +01:00
Harald Welte
51315a16ff
clock-gen: Cosmetic changes
2019-01-27 18:02:10 +01:00
Harald Welte
c82c71b3c0
clock-gen: finish routing of PCB layout
2019-01-27 17:00:46 +01:00
Harald Welte
73acd67b00
clock-gen: Connect EEPROM WP to GND to disable write-protect
2019-01-26 21:21:47 +01:00
Harald Welte
69aea8bd5c
clock-gen: Add SPI; UEXT header; mounting holes; do layout/routing
2019-01-26 20:57:42 +01:00
Harald Welte
40b61a84c9
clock-generator: Most of the layout
...
Traces are intended for dual-layer 1mm FR4 PCB with 35um copper.
2019-01-23 19:50:30 +01:00
Harald Welte
ef5f4655c8
clock-generator: More schematics work; initial placement/grouping
...
* add I2C EEPROM
* start board design file
* group parts to their respective "main part"
* define TC-2030 pinout
2019-01-23 00:13:00 +01:00
Harald Welte
63b23976a7
clock-generator: More work on schematics (USB, UART, ESD)
2019-01-21 22:43:27 +01:00
Harald Welte
bf89576eff
initial check-in of upcoming clock-generator board
2019-01-16 22:13:42 +01:00
Martin Schramm
680384cd6d
SFP: publish experimenter and breakout schematicss as pdf
2019-01-08 16:39:11 +01:00
Harald Welte
29cf4f0514
add SFP multi-source agreement to give context to the boards
2018-10-06 21:15:17 +02:00
Harald Welte
3d507d68ef
sfp-breakout: X1 pin 5 missing connection to VCC_3V3
...
Due to an overisght, pin 5 of the X1 header was missing the intended
connection to the 3V3 plane. Let's fix this. No routing changes on the
PCB required, as this simply connects the VCC plane layer to the
through-hole.
2018-09-05 12:38:19 +02:00
Martin Schramm
157dfbf79f
sfp: add part numbers for SFP conn and cage
2018-08-30 17:37:36 +02:00
Martin Schramm
2c9fc33df4
mvuart: align JP2 in 0.1' grid with JP3 (solves OSM#3037)
2018-08-23 20:41:26 +02:00
Harald Welte
ad2df019cb
sfp-{breakout,experimenter}: Commit GERBER exports
2018-08-21 19:47:28 +02:00
Harald Welte
86f788b33e
sfp: Use minimum clearance of 0.25mm as 0.15mm is needlessly tight in this board
2018-08-21 19:46:57 +02:00
Martin Schramm
74b053d521
sfp: remove unneeded layer in brd + sch
2018-08-17 21:37:47 +02:00
Martin Schramm
7ca3444a52
sfp: add LOS, TX_FAULT LEDs + add more supply pinheader on both PCBs
2018-08-17 21:33:19 +02:00
Martin Schramm
ee9af12fb6
spf: revise both SFP designs (OSM#3313/OSM#3314)
2018-08-17 19:14:25 +02:00